This beaker (tumbler) was presented to the Faculty in 1977 by Professor Arthur Bull, as a token of esteem and friendship, from the Faculty of Anaesthetists College of Medicine of South Africa. It was in this year that Professor Bull was also awarded an honorary fellowship from ANZCA. Professor Arthur Barclay Bull was a pioneer of South African Anaesthesia, having played a major role in the specialty and research in anaesthesia from 1954. One of his achievements include the use of prolonged curarisation and IPPV for treating tetanus. In 1965 - 1967 the Taurus Blood Warmer was developed - named after Professor Bull - to prevent hypothermia after major blood transfusion. Not only was Professor Bull the presenter of this beaker, but also its maker. It is hand wrought from sterling silver recovered from discarded tracheostomy tubes. The maker has hallmarked the beaker with the initials A B. Hand wrought sterling silver beaker made from the silver recovered from discarded tracheostomy tubes.To / The Faculty of Anaesthetists / R.A.C.S. / from / The Faculty of Anaesthetists / C.M. of S.A. / 1977 [hallmark in maker's logo] A Btracheostomy, taurus blood warmer, the college of medicine of south africa, faracs

During a visit to Ulimaroa in 1994, Dr Richard Howell (Coventry, West Midlands), Griselda Cooper (Queen Elizabeth Hospital, Birmingham) and David Greaves (Ashington Hospital, Northumberland) presented the College with a Royal Brierley etched vase. This gift was accepted on behalf of the college by the Registrar, Mrs Joan Sheales. Royal Brierley is a crystal glass manufacturer based in Brierley Hill, Dudley, West Midlands. It is one of the oldest crystal glass manufacturers in England which dates back to the early 17th century.Medium sized round shaped crystal vase, hand made, decorated with etched floral motifs.[LABEL] SINCE 1776 / Royal Brierley / HANDMADE / IN / ENGLANDdr howell, dr cooper, dr greaves, royal brierley

This vase was gifted to the Faculty by Dr Walter Wyndham Biggs upon his retirement from the Faculty Board in 1981. Dr Biggs was the first flying anaesthetist of the Flying Surgeon Service based at Longreach in central Queensland. The vase is hand painted by Dr Biggs mother, Bessie Biggs. The manufacturer of the vase, Furstenberg, is one of oldest and most renowned porcelain makers in Europe since 1747. Made in West Germany, the makers mark is found at the base of the vase marked with a blue under glaze symbol of a crown, script F and a number 9. Porcelain vase of bulbous form and narrow neck with gold trim on lip. Black and white hand painted scene of flying geese above a body of water surrounded by reeds.[hand written on base in black ink] Handpainted / by / Bessie Biggs / 1981 [embossed on base] 7405/30 [Blue under-glaze on base] symbol of crown / cursive script F / 9 / FURSTENBERG / SEIT 1747 / WEST GERMANY [Artist signature on painted surface] B BIGGSdr walter biggs, furstenberg, porcelain

This is a portrait of former ANZCA President, Associate Professor Richard Walsh. In 1996, he was elected Vice President and, in 1998 was elected President, serving a full two year term. This painting was formally presented to the College in 2006. Further information about Associate Professor Richard Walsh can be obtained on the Lives of the Fellows, http://anzca.online-exhibition.net/fellows/fellows-1992/richard-george-walsh/ The artist, Jiawei Shen is a Chinese Australian artist considered to be one of Australia's leading portrait artists. He is most famous for his 2006 winning entry of the prestigious Sir John Sulman Prize in which he painted a portrait of Pope Francis which was presented to His Holiness in 2014. Oil painting on canvas of Associate Professor Richard Walsh sitting to the side facing left on a blue chair, wearing the College gown and President's medal against a plain background. Mounted in a mottled brown coloured frame.Lower left hand corner [artist signature \ '05]painting, walsh, richard, anzca president, shen, jiawei

In 1940 doctors started experimenting with curare for use with electric shock therapy. Electric shock therapy regularly caused broken bones, including vertebrae, and all sorts of dislocations. The intensity of convulsions was high and couldn’t be controlled. During the 19th Century curare was unsuccessfully used to treat rabies, tetanus and epilepsy. By 1935, Harold King had isolated tubocurarine, curare’s active ingredient. In 1942, Harold Griffith successfully used standardised curare (Intocostrin) with cyclopropane. Within five years synthesised muscle relaxants were available. Intocostrin, combined with an anaesthetic agent, was a break-through for this treatment.Solid wooden box with three separate sections inside box. First section contains electrical lead for attaching unit to mains power. Second section contains ECT unit and controls. Third sections contains electrical lead ending in plugs for holding in hands. Sections cannot be separated out, they form one unit.Etched on to the face of the internal unit: PROPERTY OF / THE ROYAL WOMEN'S HOSPITAL Label tape affixed to top of the lid: E.C.T. UNIT OP. THEATRES R.W.H.anaesthesia, muscle relaxants, electroconvulsive shock therapy, women

In a gold frame there is a white flag (RAN) . There are four sections on the fag divided by red. Three of these sections are white. the one on the top left hand corner has the Union Jack.There is the number 824602 to the left of the Union Jackflag, ran, cerberus collection

Long term loan from Neurological Society of Australasia Museum of Neurosurgical Instruments,South Australia. Catalogue with Historical Commentaries Second Edition January 2006 Copy located at RACS MuseumTrumble's Skull Plough or craniotome devised by Hugh Trumble (1864-1962 ) CRANIOTOME. This craniotome was designed by Hugh Trumble (1894-1962) of the Alfred Hospital, Melbourne, one of the eight founders of the Neurosurgical Society of Australasia. It was a modification of an earlier instrument, similar in principle but less versatile, designed by Sir Henry Souttar(l875 - 1964), a very inventive surgeon who worked in the London Hospital. Souttar also used a motor-powered circular saw when necessary. He cut very large circular bone flaps, exposing the occipital lobes and posterior fossa in a few minutes. Trumble reported the use of this craniotome as "an expeditious method of cutting bone flaps" and in the designer's hands this claim was certainly justified. To use the crauiotome, it was necessary to hold the skull rigidly, and this was done by embedding the head in a plaster mould. Three holes were drilled in the skull to fix the pin of the craniotome, and the flap was then cut in a series of three arcs, after which the flap was elevated with levers until its base fractured. The 'Trumbolian" instrumentation was used in the Alfred Hospital by a number of Trumble's pupils. The craniotome is made of steel, not plated and apparently not stainless. It is believed that Trumble made his craniotomes himself, in a backyard workshop.

Benjamin Rank was considered by many to be the father of plastic surgery in Australia. He was born on 14 January 1911 in Heidelberg, Victoria, where his father, Wreghitt Rank, owned a grain store and mill. His mother was Bessie née Smith. He was educated at Scotch College, Melbourne, and Ormond College, University of Melbourne, graduating with many honours and prizes. He did a two-year residency in the Royal Melbourne Hospital before going to London to specialise in surgery. There he did junior posts at St James' Hospital, Balham, but soon became fascinated by the new specialty of plastic surgery and was appointed assistant plastic surgeon at Hill End (Bart's EMS unit). Joining the Royal Australasian Army Medical Corps in 1940, he commanded their plastic surgical unit in Egypt. In 1942, he returned to Australia to set up a plastic and maxillofacial unit at Heidelberg Military Hospital. Among the patients treated there was one Flight Lieutenant John Gorton, who went on to become Prime Minister of Australia. In 1946 he was the first honorary plastic surgeon at the Royal Melbourne Hospital. He spent much time overseas and was instrumental in setting up the specialty of plastic surgery in India, for which he set up 'Interplast' - a charity supported by the Rotary Clubs to offer training and expertise to Asian and Pacific nations. He was the Sims Commonwealth Travelling Professor of the College in 1958, Moynihan lecturer in 1972, President of the British Association of Plastic Surgeons in 1965 and President of the Royal Australasian College of Surgeons from 1966 to 1968. He made important contributions to the study of Marjolin's ulcer, radiation carcinoma, and the transition from benign to malignant melanoma. He also made a major contribution to hand surgery, and his textbook Surgery of repair as applied to hand injuries (Livingstone, 1953) ran to four editions. He wrote extensively, including an autobiography, and was a talented painter. He was a tireless campaigner for no-fault motor accident insurance and was President of the St John Ambulance Association. He married Barbara Lyle Facy in 1938. They had one son Andrew, and three daughters, Helen, Julie and Mary (one of whom became a nurse). He died on 26 January 2002. Reference; https:livesonline.rcseng.ac.uk surgeon, sir benjamin rank, heidelberg military hospital, plastic surgery, royal melbourne hospital

Mr Ernie Fitzgerald of Tarrawingee, traveled to Wangaratta, a distance of 14 Kilometres on Market days for his provisions. He was pulled along by his one of two dogs attached to a hand held leather strap (recounted by a witness who remembers Mr Fitzgerald's weekly visit to Wangaratta for supplies at The CoStore). This vehicle remains in possession of his family. This was an unique mode of transport in the 1930's, the witness was a child at the time and remembers Mr Fitzgerald and his dogs and the cart quite clearly. This is a unique mode of transport for the area, is documented and still in existence. WHS Inc were presented with 10,000 glass plate negative from Thelma & Vine Photographic Studios Murphy Street Wangaratta from the 1860's - 1950's. An example of a glass plate negative is featured above of Mr Ernie Fitzgerald of Tarrawingee who traveled to Wangaratta, a distance of 14 Kilometres on Market days for his provisions. He was pulled along by his one of two dogs attached to a hand held leather strap. (Recounted by a witness who remembers Mr Fitzgerald's weekly visit to Wangaratta for supplies). This vehicle remains in possession of his family. Unknownthree wheel steerable chair

Two men; one soldier and one Vietnamese man with hardly any front teeth. Shelves in background with instruments on them. Photographed by Robert Moffitt. Ektachrome slideTheatre staff, 8 Fd Ambulance are short of Dettol. Dental Unit has surplus of Dettol, however WO2 Geoff Andrews refuses to hand it over as the unit will be out of stock. 33DU OR;s one night empty the Dettol and replace it with water, Theatre staff thank 33DU OR's for their efforts8th field ambulance, 1st australian field hospital

A hand written letter by James Kelly Kerr to his parents. At the top of the page underlined is the wording letter 1. One page. Letter 1letter, james kelly kerr

In a black frame two coloured Photograph. the top one is of a sunken ship with the number 62 on it at sea. the bottom one there are many beached vessel parts in the sand. Bottom left hand side reads Voyages To Vietnam Collection, bottom right hand side reads Copyright Tony EyVoyages To Vietnam Collection. Copyright Tony Ey

A black and white photograph of a VIP Vietnamese Colonel, his family and his Aide-de-Camp gets a helping hand from Crew Chief Cpl Allan Hudson as "first country nationals" particularly the Military, Vietnamese had priority one status for transportation in Vietnamphotograph, cpl allan hudson, first country nationals, gibbons collection catalogue

A collage of Photograph (coloured and black and white) in a black frame of the history of RAN 1962 - 1972. In the top left hand corner is the signature by peter CosgrovePhotograhy is a means of recording forever the things one sees for a moment - Aaron Sussman A unique photographic history of the Royal Australian Navy 1962 - 1972. Photograph by Australian Veterans of the Vietnam conflictphotograph, r.a.n., general cosgrove, cerberus collection

A coloured photograph in a black frame are sailors dressed up for Melbourne Cup day. One of the sailors is dressed as a lady. Bottom righ hand corner are the words Voyages to Cietnam Collection. Bottom left hand corner are the words Copyright "Slim" Whitfieldphotograph, hmas stuart, cerberus collection

Formerly New Bath & Criterion, built in 1856. New Bath demolished in the 1860s. A new hotel was built in 1878 and altered in 1921, when it changed hands and an entertainment venue was incorporated into the former exclusively residential building. Famed for live music, it is one of the earliest, largest and most prominent 19th-century resort hotels in Victoria. It has been altered many times since and this image predates extensive renovations and restoration work in 2018.colour photographst kilda, esplanade hotel, hotel esplanade, the espy, the esplanade

Notice of a meeting of citizens, convened by the Mayor of St Kilda, to raise funds for the widow and child of the late Albert Jacka, former St Kilda Councillor (from 1929) and Mayor (1930). The meeting was held in the St Kilda Town Hall on 25 January 1932. Albert Jacka had collapsed on 14 December 1931 after a council meeting and was admitted to Caulfield Military Hospital. He died on 17 January 1932 at the age of 39. Albert Jacka is most well-known for his military service in WWI, having received the Victoria Cross medal for his actions during the Gallipoli campaign and two more decorations for his bravery on the Western Front. He received a hero's welcome on his return to Melbourne in January 1920 and an estimated 50,000 people turned up to watch his funeral procession to St Kilda Cemetery, where he was buried with full military honours. On 29 January, the appeal committee, chaired by Brigadier-General Brand, decided to call for donations to the Albert Jacka Fund by 29 February. The Fund had two objectives: 'In the first instance, the erection of a simple, suitable and inexpensive memorial stone over the grave of the dead hero, and secondly the placing of the residue of the fund in the hands of trustees for the benefit of his widow and child.'White paper, discoloured with age, printed in blue on one side.albert jacka, city of st kilda, jacka appeal

This Hand trolley was built by Chris Alger to undertake weed poisoning and other minor track work on the railway between Belgrave and Menzies Creek while the line was closed (1954-1962). From 1958, Chris often put a drum of chemical on the trolley and propelled it by hand up and down the line until the shakedown specials in 1962. Other times it just took the tools needed to keep the line free of trees and other weeds. Chris was on the Puffing Billy Preservation Society committee for a number of years in the early days and contributed funds to Puffing Billy Preservation Society projects.Narrow Gauge - Puffing Billy Railway - track maintenance Hardwood planks, Hardwood frame Flat 4 wheel, 2'6" rail trolley Removable Steel "T" handle Brake applies to one wheelNone2'6", puffing billy, pbps, trolley, chris alger, narrow gauge

The trolley entered service for the Commonwealth Railways (later Australian National Railways) as trolley number "386" and was originally built to the gauge of 3"6.Historic - Commonwealth Railways - Narrow Gauge Railway - Track vehicleThe tricycle is red and has three wheels, two large on one side with a single offset wheel on the other. Timber and steel constructionhand tricycle, commonwealth railways, australian national railways, trolley, puffing billy

This type of trolly is known to date from prior to 1910 and were in use before petrol engines were used to transport workmen along the railway lines. The exhibit was located at Colac in 1961, after being used on the Colac to Beech Forest and Crowes narrow gauge railway. This type of trolly was built in two versions; one for the Victorian Railways broad gauge lines, and one for the narrow gauge lines.Historic - Victorian Railways narrow gauge - track work vehicle. This vehicle was used in the days before petrol engines were used to drive vehicles transporting workmen along the railway line.C2N Type Trolly - Victorian Railways Gauge 2'6" Trolly Has a flat piece of wood that you would stand on with four metal wheels, one under each corner.c2n, trolley, victorian railways, hand power, narrow gauge, puffing billy, trolly

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

The Museum was first considered in 1963 when it was felt that Victorian narrow gauge railway history was quickly being destroyed by progress. Originally it was planned to only cater for two locomotives and some rolling stock associated with the Moe and Walhalla Railway. Construction of the site commenced on Labour Day Weekend in March 1964, the area was then fenced. The first exhibit arrived soon after and companies with locomotives and other railway features offered items to the Museum. When interesting exhibits from the "Steam Era " were known to be coming available,discussions were held with the owners in an attempt to obtain the item for preservation. In 1965 an Umbrella style shed was built and by May, the first locomotive ex Erica State Saw Mill (CLIMAX) had arrived. The Museum was opened to the public in November 1970 but was officially opened by His Excellency the Governor of Victoria, Sir Rohan Delacombe on Saturday 7th April 1973.Historic - Puffing Billy Museum Entry SignPuffing Billy Museum Entry Sign Rectangular hand painted sign in use from 1970.Puffing Billy Museum This is one of the Volunteer activities of The Puffing Billy Preservation Society Preserving part of our National Heritage Proud to Help Preserve Australia's Heritage puffing billy, menzies creek, sir rohan delacombe, narrow gauge, steam

The Lister Auto-Truck was a small monowheel tractor built for moving light loads around factories, railway yards and similar sites. They were built by R A Lister and Company of Dursley, Gloucestershire, well known for their range of small stationary engines The Auto-Truck was one of several monowheel tractors to appear in the 1920s and '30s, with the availability of small, reliable petrol engines, as developed for motorcycles and the stationary engines for which Lister were already known. These were tricycle vehicles, with the single leading wheel used for both drive and steering. Their simple construction carried most of the mechanism on this wheel as a single unit, the chassis with the trailing wheels being little more than a trailer for balance. Simplicity was a key feature. The engines were single-cylinder and air-cooled. Ignition was by magneto, rather than requiring a battery and electrical system. One of these designs was produced in the 1920s by George Grist of the Auto Mower Co., Norton St Philip, Somerset. The engine was a JAP 600 cc four-stroke air-cooled sidevalve, a typical small engine of the time. The Auto Mower Co. were Lister agents and when Lister heard of this 'Auto-Truck' they bought one for use in their own factory. It was used to carry heavy engine castings from the foundry to the machine shop. Lister customers saw them and there was such interest in wanting to buy them that Lister negotiated with Auto Mower to build them under licence. Although Lister were already well known for their small petrol stationary engines, these were heavy cast-iron engines with water hopper cooling and unsuitable for vehicle use. Lister remained with the JAP engine for the Auto-Truck. The Auto-Truck was designed for use in factories or other places with smooth surfaces of concrete or tarmac. This allowed the use of small solid-tyred wheels with only simple suspension, making the vehicle simple, cheap and lightweight. They had little ability on soft surfaces though and could even topple over if driven carelessly across slopes. Their design was a compromise between the top-heavy nature of the tall engine grouping above its wheel and a well thought-out chassis for stability. The bearing between them was a large diameter ring roller bearing, mounted at the lowest part of the chassis. This gave rigidity and stability, even after long wear. A ring of rolled channel girder was attached to the engine group and rollers on the chassis carried the load upon this. On early Auto-Trucks this bearing is set very low, in line with the chassis members, and is covered by thin steel plates. The front panel of the engine cover is distinctive with large ventilation holes and a Lister signature cut through it. Strangely this panel is made of thick cast iron, providing substantial weight high on the engine and only adding to its top heaviness. To improve visibility of moving vehicles in noisy factories, this panel was often painted white, the rest of the vehicle being Lister's usual brunswick green. The driver was seated on a Brooks bicycle saddle, which in recognition of the lack of vehicle suspension, was carried on the end of a cantilevered bar that acted as a leaf spring. A wide handlebar on the engine group was used for steering. A squeeze bar the width of this handlebar engaged the clutch. Controls included a hand throttle, a gear lever with two forward and one reverse gears, and a large handbrake lever. The engine unit rotated freely for a full 360° rotation. When used in reverse, the Auto-Truck could either be driven from the saddle, looking backwards over the driver's shoulder; or they could dismount, swivel the engine unit around and control it as a pedestrian-controlled truck from behind. Under the engine cover were two equal diameter tanks, a fuel tank for petrol and a shorter oil tank. Engine and chain-drive lubrication used a total-loss oil system, controlled by a small pump and needle valve. Info Ref: Lister Auto-Truck - Wikipedia https://en.wikipedia.org/wiki/Lister_Auto-TruckHistoric - Industrial monowheel tractor for moving light loads around factories, railway yards and similar sites.The Lister Auto-Truck - small monowheel tractor Made of steel with three wheels. Powered by a J.A.P single cylinder petrol motor which is Hand Cranked to start.Lister puffing billy, lister, lister auto truck, monowheel tractor

Zeehan & North East Dundas Tramway Bogie 1896 The North East Dundas Tramway (NEDT) was a 2 ft (610 mm) narrow gauge tramway on West Coast Tasmania that ran between Zeehan and Deep Lead (now Williamsford). It was part of Tasmanian Government Railways. The line was opened in 1896 to carry ore from the Williamsford mines to Zeehan where it would be loaded onto another train for shipment to Burnie. The narrow-gauge (2 ft) was chosen because of the extremely difficult terrain that the railway crossed, requiring several big trestle bridges, including one at the foot of Montezuma Falls. After some rain the engine and carriages would get soaked by spray from the falls. There was a break-of-gauge with the mainline 1,067 mm (3 ft 6 in) system at Zeehan. The railway was closed in 1932. The rolling stock for the Tramway was built in the Launceston Railway workshops, and comprised twenty five eight-wheel low-side trucks, tare 3 tons 1 cwt. 1 qr., load 10 tons; six eight-wheel flat trucks, tare 2 tons 18 cwt. 1 qr., load 10 tons; two four-wheel bolster trucks, for carrying long timber, tare 1 ton 19 cwt., load 5 tons; and four passenger cars, each with six cross-seats with reversible backs, to carry eighteen passengers, also a locker for mails and parcels. All trucks and cars have cast-steel wheels 21 inches in diameter and are fitted with automatic vacuum brakes. The trucks have side levers and the cars have hand-screw brakes. The vacuum brake can be worked from the engine or from the passenger cars, which act as brake vans. When this brake was introduced, one effect was to accelerate the journey speed by about 10 minutes owing to more even running on down gradients. Historic - Industrial Narrow Gauge railway - Bogie used on the Zeehan & North East Dundas Tramway, Tasmania, Australia Bogie made from steel, iron and wrought ironZN & NTDS ML TRAM 1896 Griffinpuffing billy, bogie, zeehan & north east dundas tramway bogie, zeehan & north east dundas tramway, industrial narrow gauge railway, gauge: 2' (610 mm)

Electric staff - Electric staff instruments The staff and ticket system was still too inflexible for busy lines, as it did not allow for the situation where the train intended to carry the actual token was cancelled or running very late. To provide for this, the electric train token system was developed. Each single-line section is provided with a pair of token instruments, one at the signal box at each end. A supply of identical tokens is stored in the instruments, which are connected by telegraph lines. A Staff can be removed from one instrument only if both signalmen co-operate in agreeing to the release. Once a Staff has been removed, another cannot be removed until the token which is "out" is replaced in either instrument. (There are variations on this sequence of events.) By this means, it can be ensured that at any one time, only one token is available to be issued to a driver. Staff belonging to adjacent sections have different configurations to prevent them being inserted into the wrong instrument. Nevertheless, in the Abermule train collision in 1921 and lax working procedures allowed the safeguards provided by the electric Staff system to be circumvented; a driver was handed a Staff for the wrong section, and without reading the information listed on the staff, proceeded on the mistaken belief that the Staff was correct. To prevent this, it became a requirement in the UK for the signals controlling entry to the single line section (starting or section signals) to be locked at danger unless a token has been released from the relevant Staff instrument. Historic - Victorian Railways Electric Staff Instrument Electric Staff Instrument made of Iron , Brass and Glasspuffing billy, electric staff instrument, victorian railways

Porters Luggage Trolley - large red one Used for transporting luggage and other items on a railway platforms by porters and other station staff.Historic - Victorian Railways - Station Porters platform Luggage Trolley Large Porters Trolley - made of wood and steelpuffing billy, victorian railways, porter, luggage, hand trolley

Staff exchanger hoop - Leather Bakelite and wooden prop staff. The hoop held the 'Staff’ giving authority for a locomotive or rail vehicle permission to travel over a specified section of track. The display shows the hand held type used from person to person. Hand held staffs were exchanged at low speeds or stationary. Automatic staff exchangers were also in use when a vehicle was not required to travel at low speed to exchange the staffs and were used by express trains. To exchange the 'Staff’ from the platform or signal box to the locomotive driver, the hoop was held up in the air by the person, and collected by the Drivers arm. The reverse occurred when the staff was being given by the Driver. Both exchanges may occur where one section of line ends and another commences.Historic - Railways - Staff exchanger hoop - used for person to person exchanging.Staff exchanger hoop made of Leather Bakelite and wooden prop staffpuffing billy, staff exchanger hoop

24 NB - Carriage (NB 3rd series) 6 compartments (36) Vehicle Length 29 feet 6 inches ( 8992 mm) Coupled Length 31 feet 4 inches (9550 mm) Width 6 feet 7 inches (2007 mm) Height 9 feet 9 inches (2972 mm) Weight 11 tons Capacity 40 passengers, or 36 with guard's compartment. Built 1906 - 1915 Number Built (1st Series) 6 Number Built (2nd Series) 17 Number Built (3rd Series) 4 In use NB 24 VR Service History NABAB 4.VA - 18/ 9/1909 NWS Built new - circa 1910 - To NAB 4.VA - NAB 4.VA - 18/ 6/1917 - To NB 24.VA - *NB 24.VA - / 6/1926 - Modified AC Malco 19/ 1/1932 NWS Into Workshops - 10/ 5/1932 NWS Out of Workshops (113 days) 21/ 6/1933 NWS Into Workshops - 17/ 8/1933 NWS Out of Workshops (58 days) 28/ 8/1934 NWS Into Workshops - 13/ 9/1934 NWS Out of Workshops (17 days) 9/ 2/1937 NWS Into Workshops - 17/ 3/1937 NWS Out of Workshops (37 days) 31/ 5/1940 NWS Into Workshops - 5/12/1940 NWS Out of Workshops (189 days) 27/ 1/1948 NWS Into Workshops - 29/ 7/1948 NWS Out of Workshops (185 days) 12/12/1954 - Scrapped Body to Eng. Spcl Works 17/ 8/1957 - Traced at Stocktake STET - Return to Register Puffing Billy Service History or Notes NB (3rd series) The Puffing Billy Railway built a guard's compartment built in 24 NB. This reduced the passenger capacity to 36. The car retained its classification as NB in an attempt to emphasise that this was only a temporary conversion. The NBC classification was already in use. One day the guard's compartment will be removed and the vehicle returned to the classification of NB. The guard's compartment has a radio, air brake taps and gauges but no hand brake.Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: NB Passenger carriage Passenger carriage 24NB - Carriage (NB 2nd series 6 compartments), Timber body on a steel frame 24NBpuffing billy, 24nb, nb passenger carriage, 2'6" guage, victorian railways, narrow gauge passenger rolling stock

NBD This is a Puffing Billy Railway reclassification of the first series of NB carriages. COMBINED NB PASSENGER CAR AND GUARD'S VAN. A saloon or end platform NB which has had a guard's compartment temporarily added in one end. Due to the temporary nature of this conversion, this vehicle also retains its original number in the NB numbering sequence but is classed NBD to differentiate it from the standard NBC and the NAC. The use of the letter 'D' in the classification is recognising the code for guard's vans prior to 1910. NB Class - Number Built (1st Series) 6 - Number Built (2nd Series) 17 - Number Built (3rd Series) 4 NB (1st series) NB 5 was equipped with a vertical hand brake at one end to enable it to be used as the last vehicle of a train. Body Length 20 feet 6 inches ( 6248 mm) Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 5 inches (2870 mm) Weight 8 tons Capacity 16 passengers Built 1898 - 1904 Number Built 6 In use NBD 1, 2, 5 NB - Puffing Billy Railway classed these as NBD to indicate their use as a trailing vehicle with guard's accommodation. 5 NBD Victorian Railways Service History NBB 5. ( it's original number ) Built new - - / 6/1901 Newport Workshops 4/ 2/1902 - In Service "Commenced running" circa 1910 - renumbered To NB 5 *NB 5. - / 6/1926 - Modified AC Malco 5/ 2/1951 - Scrapped - Body and underframe purchased by Puffing Billy Preservation Society from Pakenham. Restored by the Puffing Billy Preservation Society 1975. In July 2006 work commenced on 5 NB to make it a temporary kitchen car for the luncheon/dinner train. It has had the seating removed from the saloon and kitchen equipment installed. Plans are for a kitchen car to be constructed and 5 NB restored to carry passengers.Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger and Guard's Van carriage 5 NBD - converted into Catering Car and Guards vanMade of Timber and steel 5NBDvictorian railways, narrow gauge rolling stock, 5nbd - catering car and van, puffing billy

11NBHC Passenger Carriage - Excursion Car and Guard's Van Excursion Car 11 NBH which has been converted by the addition of a Guard's Van compartment by Puffing Billy Railway and re classed & numbered 11 NBHC The NBHC is a conversion from the standard NBH. This was a temporary, but long term, conversion to overcome lack of suitable guard's vans on the Puffing Billy railway. One end of a standard NBH had windows and a hand brake fitted. A padded seat replaced the standard back to back seating, and a partition separated the guard from the passenger compartment. VR Service History *NBH 11.VA - 8/12/1919 NWS Built new - / 1/1929 - Modified AC Malco BO circa 1955 - Condemned - Puffing Billy Service History or Notes Body Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 2 inches (2794 mm) Weight 8 tons Capacity 22 passengers Number Built 1 In use 1 Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger Carriage - Excursion Car 11 NBH which has been converted by the addition of a Guard's Van compartment by Puffing Billy Railway and re classed & numbered 11 NBHC 11 NBHC - Passenger Carriage - Excursion Car and Guard's Van made of wrought iron and timber11NBHCpuffing billy, pbr, rolling stock , 11 nbhc, victorian railways, passenger carriage - excursion car and guard's van, 11nbh