52NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs Puffing Billy Service History or Notes Coupled Length 31 feet 4 inches (9550 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 2 inches (2794 mm) Weight 8 tons Capacity 24 passengers, or 20 passengers and 3 wheelchairs, or 16 passengers and 6 wheelchairs Number Built 2 In use 2 In 1981 the first of two extended NBHs with provision for wheelchair passengers (double door access and fold-up seats) was built, the second following in 1983. These were numbered 51 & 52 - a separate number series because of their length made them different from the other NBHs. May 2016 - In for repairs to the roofHistoric - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car specially built for Wheelchairs access52 NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs made of wrought iron and timber52NBHpuffing billy, pbr, rolling stock , 52 nbh, narrow gauge - passenger rolling stock: excursion car for wheelchair

This box was made for the Royal Dunkeld School in Scotland to participate in a flag exchange with with the Dunkeld State School No 183 in Victoria, Australia in 1910. It was made from the wood of one of three Larch trees planted in Dunkeld Scotland by the 2nd Duke of Athol from seeds which were brought from the Tyrol. The tree was struck by lightning in 1905 and died over the next few years. It was cut down and some of the timber was used to make the box.This box was sent to the Dunkeld State School from the Royal School of Dunkeld, Scotland and part of a state wide flag exchange in Victoria in 1910. Schools were encouraged to contact schools with a similar name. This box contained a Union Jack which was first flown at the Dunkeld, Victoria school on Empire Day 1910. A box made of Australian Ash was sent to Scotland with an Australian flag enclosed.Timber box made from larch wood. Silver shield on the lid and plaque on the front edge of the lid and crossed flags on the front of the box with a portrait of King George 5th and a banner engraved "God Save the King". Handles on the end are brass lions heads with rings through their mouth. Lock keeper is silver in the form of a Maltese Cross.. The lid has bevelled sides and ends and the interior has strengthening bars in the corners and inside the lid is the provenance of the timber.On top a shield with a bird and a thistle and the letters RDS. Below this a bannet with the words Forward with Honour. On the front bevel of the lid a plaque with "Presented to Dunkeld State School Victoria Australia from Dunkeld Royal H.G. School Scotland 24th may 1910. On the front. Banner with God save the King. Crossed flags representing either the Union Jack or the Scottish Saltair and the Australian Flag and a medallion with the head of King George 5th in relief.

Item belonged to William David Maher No 68, 8th LH Regt AIF. Refer 532 for main details. .1) Container, brass, round, made from possibly a 3" shell, engraved all around with depictions of small branches, leaves etc. Engraving is "Souvenir from the Great war " - "Made by G. KAMPER Duisberg Germany." .2) Lid, brass, round for .1) Lid is possibly a 3" shell with a small handle centre made from a round possible .303 size.,1) Marz, 1917. ST.G33,HL25 .2) DEZ 1917 ,ST, G,297 ,67,HL31arms - ammunition, brassware, engraving, trench art

Banner with the Logo of the Northern District School of Nursing.Banner made from white cotton coated curtain fabric with the logo of the Northern District School of Nursing made with applique fabric and fabric paint in red and gold. The banner is supported top and bottom with lengths of dowel inserted into a hemmed section. The banner was made by Max Ellis for the five yearly reunion of the Northern District School of Nursing Graduates' association held in 2000.banner, reunion, northern district school of nursing, ndsn

KING RAZOR MFG. CO.Pittsburgh, Pennsylvania; moved to Indiana, Pennsylvania in 1911.ca. 1904 - 1919 Marked "Made in Germany", although the company's offices were located at 118 E. 28th Street, New York City. ca. 1934-1943 Used the "THE KING OF RAZORS REGISTERED TRADEMARK" trademark. 47-1/2 and Trademark: Crown and Wolf. For 500 years the Weyersberg family has been producing the finest blades in the world. For centuries the King’s Crown™ mark has been synonymous with exacting precision, hand-craftsmanship and quality. For the first few hundred years the blades, made in Solingen, Germany (the “City of Blades”), were for swords. As times changed, the Weyersberg family transitioned into making cut throat razors. The Greb. Weyersberg™ family business.continue to place our mark on each and every product sold as we have done since first being able to register it in 1774. For over a 100 years, the straight razors continue to be produced in Solingen (Germany). King's Crown™A folding cut-throat razoron blade ; KING'S / CROWN 'a crown trademark' RAZOR / EXTRA HOLLOW GROUND around 'trademark' ; SET READY FOR USE on steel handle; MADE IN GERMANYcut-throat razors, straight razors, shaving equipment, steel blades, swords, weyersberg family, king crown pty ltd., solingen, germany, early settlers, market gardeners, moorabbin, bentleigh, cheltenham,

Owned by Sig. L. W. Hanger who enlisted in February 1942 at Caulfield and was discharged in December 1945. Last posting was with 5 Aust. Jungle Trunk Line Maintenance Section with rank of Lance Corporal. Note: Although these helmets were designed for Motorcycle Despatch Riders, they were also widely used by the 1st Australian Parachute Battalion from 1943-1945 due to a lack of available British Steel Airborne Helmets. Despatch rider's helmet made of Duperite (similar to Bakelite) with leather wraparound side and back below helmet. Cloth webbing inside for firm fitting. (See photos for detail of leather wrap and internal webbing). Chinstrap buckle and tongue attached to leather wrap.External front of helmet: ink-stamped Despatch Rider insignia Name (Inside on webbing support): Sig. L.W. Hanger Service Number (Inside on webbing support): VX74482 Manufacturer's Label (inside): Duperite 1942 Made In Australia THIS HELMET IS SUITABLE FOR HEAD SIZES 6 3/4 TO 7 MODEL No. 2200/2 (See photos for more detail of Label)

Marion “Annie” (Cooper) Harrison, a milliner by trade, designed and made women’s hats, initially in the 1940s in High Street, and later in the 1950s and 60s at 5 Princess Street. The hats were constructed upstairs in her shop in Princes Street while the ground floor was reserved for sales and display. She employed other milliners to assist but always ran the showroom herself. Hectic periods were in the weeks before the big racing carnivals when the many wealthy race-goers of Kew kept her busy. She typically walked to her business as she and her husband, Fred Harrison, lived locally. Annie died in April 2016, at the great age of 107 years. Her hats are held in local and national collections.The Kew Historical Society’s fashion and design collection is comprised of costumes, hats, shoes and personal accessories. Many of these items were purchased or handmade in Victoria; some locally in Kew. The extensive hat collection comprises items dating from the 1860s to the 1970s. While most of the hats in the collection were created by milliners for women, there are a number of early and important men’s hats in the collection. The headwear collection is particularly significant in that it includes the work of notable Australian and international milliners.Pale green and black felt woman’s hat retailed by Anne Harrison of Kew. The pale green crown is bordered by a black turned up rim. An additional adornmant to the hat is an abstract bow at the front made of black felt.Label: Anne Harrison of Kew. WM 9906.anne harrison, women's clothing, costume accesories - hats, fashion and textiles collection - kew historical society, cloche hats, milliners - kew (vic)

The apparently haphazard arrangement of fabric pieces in a quilt made of scraps doesn't always preclude a conscious sense of design. The pieces in this quilt have been carefully arranged according to size and colour, possibly indicating that it was intended to go on a bed as a spread without a cover. Placed in a room that may not have been adorned with many other decorative items, this quilt would have been a colourful and inexpensive home furnishing solution.Patchwork quilt made from large pieces of wool suitings, colourful clothing off cuts and woollen blankets. The quilt has been hand stitched together with stitches that hold the front and back sides together. Either a large single bed size or small double bed size.quilting history, patchwork history, running stitch group, running stitch collection, quilting - history, patchwork - history

A note was attached to this tablecloth when it was donated "made by G.L. Angus for Helen - Berry ". Berry is the daughter of Gladys and Dr W.R. Angus. The tablecloth was donated to Flagstaff Hill Maritime Village by the family of Doctor William Roy Angus, Surgeon and Oculist. It is part of the “W.R. Angus Collection” that includes historical medical equipment, surgical instruments and material once belonging to Dr Edward Ryan and Dr Thomas Francis Ryan, (both of Nhill, Victoria) as well as Dr Angus’ own belongings. The Collection’s history spans the medical practices of the two Doctors Ryan, from 1885-1926 plus that of Dr Angus, up until 1969. ABOUT THE “W.R.ANGUS COLLECTION” Doctor William Roy Angus M.B., B.S., Adel., 1923, F.R.C.S. Edin.,1928 (also known as Dr Roy Angus) was born in Murrumbeena, Victoria in 1901 and lived until 1970. He qualified as a doctor in 1923 at University of Adelaide, was Resident Medical Officer at the Royal Adelaide Hospital in 1924 and for a period was house surgeon to Sir (then Mr.) Henry Simpson Newland. Dr Angus was briefly an Assistant to Dr Riddell of Kapunda, then commenced private practice at Curramulka, Yorke Peninsula, SA, where he was physician, surgeon and chemist. In 1926, he was appointed as new Medical Assistant to Dr Thomas Francis Ryan (T.F. Ryan, or Tom), in Nhill, Victoria, where his experiences included radiology and pharmacy. In 1927 he was Acting House Surgeon in Dr Tom Ryan’s absence. Dr Angus had become engaged to Gladys Forsyth and they decided he further his studies overseas in the UK in 1927. He studied at London University College Hospital and at Edinburgh Royal Infirmary and in 1928, was awarded FRCS (Fellow from the Royal College of Surgeons), Edinburgh. He worked his passage back to Australia as a Ship’s Surgeon on the on the Australian Commonwealth Line’s T.S.S. Largs Bay. Dr Angus married Gladys in 1929, in Ballarat. (They went on to have one son (Graham 1932, born in SA) and two daughters (Helen (died 12/07/1996) and Berenice (Berry), both born at Mira, Nhill ) According to Berry, her mother Gladys made a lot of their clothes. She was very talented and did some lovely embroidery including lingerie for her trousseau and beautifully handmade baby clothes. Dr Angus was a ‘flying doctor’ for the A.I.M. (Australian Inland Ministry) Aerial Medical Service in 1928 . Its first station was in the remote town of Oodnadatta, where Dr Angus was stationed. He was locum tenens there on North-South Railway at 21 Mile Camp. He took up this ‘flying doctor’ position in response to a call from Dr John Flynn; the organisation was later known as the Flying Doctor Service, then the Royal Flying Doctor Service. A lot of his work during this time involved dental surgery also. Between 1928-1932 he was surgeon at the Curramulka Hospital, Yorke Peninsula, South Australia. In 1933 Dr Angus returned to Nhill and purchased a share of the Nelson Street practice and Mira hospital (a 2 bed ward at the Nelson Street Practice) from Dr Les Middleton one of the Middleton Brothers, the current owners of what previously once Dr Tom Ryan’s practice. Dr Tom and his brother had worked as surgeons included eye surgery. Dr Tom Ryan performed many of his operations in the Mira private hospital on his premises. He had been House Surgeon at the Nhill Hospital 1902-1926. Dr Tom Ryan had one of the only two pieces of radiology equipment in Victoria during his practicing years – The Royal Melbourne Hospital had the other one. Over the years Dr Tom Ryan had gradually set up what was effectively a training school for country general-practitioner-surgeons. Each patient was carefully examined, including using the X-ray machine, and any surgery was discussed and planned with Dr Ryan’s assistants several days in advance. Dr Angus gained experience in using the X-ray machine there during his time as assistant to Dr Ryan. When Dr Angus bought into the Nelson Street premises in Nhill he was also appointed as the Nhill Hospital’s Honorary House Surgeon 1933-1938. His practitioner’s plate from his Nhill surgery is now mounted on the doorway to the Port Medical Office at Flagstaff Hill Maritime Village, Warrnambool. When Dr Angus took up practice in the Dr Edward and Dr Tom Ryan’s old premises he obtained their extensive collection of historical medical equipment and materials spanning 1884-1926. A large part of this collection is now on display at the Port Medical Office at Flagstaff Hill Maritime Village in Warrnambool. In 1939 Dr Angus and his family moved to Warrnambool where he purchased “Birchwood,” the 1852 home and medical practice of Dr John Hunter Henderson, at 214 Koroit Street. (This property was sold in1965 to the State Government and is now the site of the Warrnambool Police Station. and an ALDI sore is on the land that was once their tennis court). The Angus family was able to afford gardeners, cooks and maids; their home was a popular place for visiting dignitaries to stay whilst visiting Warrnambool. Dr Angus had his own silk worm farm at home in a Mulberry tree. His young daughter used his centrifuge for spinning the silk. Dr Angus was appointed on a part-time basis as Port Medical Officer (Health Officer) in Warrnambool and held this position until the 1940’s when the government no longer required the service of a Port Medical Officer in Warrnambool; he was thus Warrnambool’s last serving Port Medical Officer. (Masters of immigrant ships arriving in port reported incidents of diseases, illness and death and the Port Medical Officer made a decision on whether the ship required Quarantine and for how long, in this way preventing contagious illness from spreading from new immigrants to the residents already in the colony.) Dr Angus was a member of the Australian Medical Association, for 35 years and surgeon at the Warrnambool Base Hospital 1939-1942, He served as a Surgeon Captain during WWII1942-45, in Ballarat, Victoria, and in Bonegilla, N.S.W., completing his service just before the end of the war due to suffering from a heart attack. During his convalescence he carved an intricate and ‘most artistic’ chess set from the material that dentures were made from. He then studied ophthalmology at the Royal Melbourne Eye and Ear Hospital and created cosmetically superior artificial eyes by pioneering using the intrascleral cartilage. Angus received accolades from the Ophthalmological Society of Australasia for this work. He returned to Warrnambool to commence practice as an ophthalmologist, pioneering in artificial eye improvements. He was Honorary Consultant Ophthalmologist to Warrnambool Base Hospital for 31 years. He made monthly visits to Portland as a visiting surgeon, to perform eye surgery. He represented the Victorian South-West subdivision of the Australian Medical Association as its secretary between 1949 and 1956 and as chairman from 1956 to 1958. In 1968 Dr Angus was elected member of Spain’s Barraquer Institute of Barcelona after his research work in Intrasclearal cartilage grafting, becoming one of the few Australian ophthalmologists to receive this honour, and in the following year presented his final paper on Living Intrasclearal Cartilage Implants at the Inaugural Meeting of the Australian College of Ophthalmologists in Melbourne In his personal life Dr Angus was a Presbyterian and treated Sunday as a Sabbath, a day of rest. He would visit 3 or 4 country patients on a Sunday, taking his children along ‘for the ride’ and to visit with him. Sunday evenings he would play the pianola and sing Scottish songs to his family. One of Dr Angus’ patients was Margaret MacKenzie, author of a book on local shipwrecks that she’d seen as an eye witness from the late 1880’s in Peterborough, Victoria. In the early 1950’s Dr Angus, painted a picture of a shipwreck for the cover jacket of Margaret’s book, Shipwrecks and More Shipwrecks. She was blind in later life and her daughter wrote the actual book for her. Dr Angus and his wife Gladys were very involved in Warrnambool’s society with a strong interest in civic affairs. He had an interest in people and the community They were both involved in the creation of Flagstaff Hill, including the layout of the gardens. After his death (28th March 1970) his family requested his practitioner’s plate, medical instruments and some personal belongings be displayed in the Port Medical Office surgery at Flagstaff Hill Maritime Village, and be called the “W. R. Angus Collection”. The W.R. Angus Collection is significant for still being located at the site it is connected with, Doctor Angus being the last Port Medical Officer in Warrnambool. The collection of medical instruments and other equipment is culturally significant, being an historical example of medicine from late 19th to mid-20th century. Dr Angus assisted Dr Tom Ryan, a pioneer in the use of X-rays and in ocular surgery. Tablecloth, part of the W.R. Angus Collection. Cream cut-work tablecloth, square shape. Tablecloth was made by Gladys Argus, wife of Dr W.R. Angusflagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, dr w r angus, gladys argus, handcrafted tablecloth, cut-work tablecloth 1900's, table linen, manchester

The Olivetti company was founded in Italy in 1908.This particular typewriter is a Olivetti Lettera 22, oblique front stroke and portable manufactured after 1950. The 1950s and 1960s was a time when British manufactured goods were still purchased by many Australian consumers. The later 1960s onwards, there was a shift, mainly in the cities, to European made goods. The invasion of Japanese manufactured goods was relatively slower, especially in rural areas. The demand for long lasted and dependable merchandise was in the rural area still the most important criteria. The ease of setting up this typewriter and its compact mobility was its major benefit to trades people and travelling professionals, e.g. rural doctors, other medical professionals, accountants, lawyers and educators. This item facilitated the growing numbers of professional nomads requiring a relatively light office stationery package e.g. travelling novelist, writer, businessman and academics. This typewriter needed no electrical or battery power to operate it. Outback Australia, where at this point in time, was still relatively isolated from a good available electrical power reticulation and battery power, and therefore could not be totally measured as a highly efficient office environment.Although this typewriter was purchased from a business in Penrith, Sydney, N.S.W., it is significant that it travelled easily to the Kiewa Valley, demonstrating the mobility of certain sections of the community. This typewriter was designed by an Italian industrial designer, Marcello Nizzoli, in line with the art deco style of the 1930s and the colour and flexibility of the vibrant 1950s. The underlying theme of manufacturing in the 1950s was to produce equipment that was more efficient than what was inherited from the earlier period of 20th century. Improvements were made to this Olivetti typewriter by Giuseppe Beccio by reducing the number of parts made from 3,000 to 2,000. This reduction of parts and therefore cost of production was the major principle of the Japanese manufacturing juggernauts of the post World War II era. Efficiency and low costs material was becoming prime factors in the success of rural industries from the 1960s. Competition from overseas producers was starting to affect rural industries and the removal of the large range of tariff protection, especially rural products, required not only a shift of farm management but a more efficient cost savings modus operandi. This Olivetti Lettera 22, oblique front stroke portable (weighs 4kg) mechanical typewriter has a coral coloured plastic casing. The keys are made of black hardened plastic with white lettering, numbers and symbols (imperial fractions, and pound). It has a QWERTY keyboard as opposed to the Italian QZERTY. It has a lever to move the ribbon between black, neutral (for mimeograph stencils)and red colours (a red key is provided for highlighting specific words,letters or symbols) . This machine is fitted with only a black ribbon. It has a black rubber paper rollers and chromed metal parts on the carriage way. It has four rubber feet underneath the main body. On the left side of the roller there is a lever to adjust the roller from fixed (when mobile) through 1,2 and 3 line space gradients. This model has a key for zero but not one for the number one (uppercase letter l is used) see KVHS 0459 for the carrying bag.On the cover over the ribbon wheels letter strikers has a plate marked "Lettera 22" and the back plate behind the paper roller and in front of the paper supports has a silver metal label marked "olivetti made in great britain".commercial, mobile office equipment, mechanical typewriter

This brass cow bell was recovered from the wreck of the sailing ship ‘Loch Ard’ at Mutton Bird Island, near Port Campbell, Victoria, from late 1960s to early 1970s. Cow bells were listed as part of the cargo on board the Loch Ard. This bell is now part of the John Chance collection. Flagstaff Hill Maritime Village’s divers also recovered similar bells from the Loch Ard wreck in 1973. One of them was found in a sandy hole in the centre of the wreck site. All of the recovered cow bells are without their hangers. A bell of this size could have been used by horse or cattle teams. Cow bells were a common Colonial item. They were hung around the necks of grazing domestic cows and goats, bullock and horse teams, even camel teams so that they could be found again. Sheep and cattle drovers used them as a warning for night time disturbances such as wild animals. The maker of the cow bell, James Barwell, was a bell founder established in Birmingham, England, from 1784. In 1842 he acquired Fiddian’s firm of ‘Steam and Water’, keeping its name and stamping it on some of his products. According to his advertisement in the Exhibitors guide for the Church Congress of 1887, he made bells and fittings for churches and schools. He also made bells for cloches and chimes, and made tuned musical handbells. He repaired and reproduced bells, and he had a team of experienced ringers to “inspect towers and report upon the tone and condition of bells and fittings.” In 1903 he became incorporated as a Limited Company, ‘engineers’ and plumbers’ brasswork, and bell founders.’ In 1914 he advertised as ‘Cock and Bell Founders’, specialising in plumbing and engineering fittings, church bells, and “every description of hanging and hand bells.” Some of Barwell’s products were stamped with his maker’s mark (his initials J. B. either side of a cross entwined with a ‘B’ in an oval of oak leaves (for Birmingham)). James Barwell bells were no longer made after 1920. James Barwell was among makers who exported bells to the Australian colony from the 1860s. Early Australian iron animal bells were also made from the 1860s by blacksmiths such as Anthony Morgan from 1861, August Menneke from 1867, and Samuel Jones from 1868. Few brass bells were produced here in those times. This bell is historically significant as typical of a cow bell used by farmers and herdsmen in Colonial Victoria. Its significance is increased by being an artefact recovered by John Chance, a diver from the wreck of the Loch Ard and other wrecks in the late 1960s to early 1970s. Items that come from several wrecks along Victoria's coast have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value. The cow bell is also significant for being part of Flagstaff Hill’s collection of artefacts from LOCH ARD, which is significant for being one of the largest collections of artefacts from this shipwreck in Victoria. It is significant for its association with the shipwreck, which is on the Victorian Heritage Register (VHR S417). The collection is significant because of the relationship between the objects, as together they have a high potential to interpret the story of the LOCH ARD. The LOCH ARD collection is archaeologically significant as the remains of a large international passenger and cargo ship. The LOCH ARD collection is historically significant for representing aspects of Victoria’s shipping history and its potential to interpret sub-theme 1.5 of Victoria’s Framework of Historical Themes (living with natural processes). The collection is also historically significant for its association with the LOCH ARD, which was one of the worst and best known shipwrecks in Victoria’s history. Cow bell; heavy brass, flat top, pyramid shape, rectangular head, shoulders flare out to rectangular mouth. The head has two same-sized tooled holes for adding the hanging yoke. Inscription on top and one side. Encrustations are on the metal in places. The hanger and clapper are missing. Made by James Barwell of Birmingham.Stamped on the head "BARWELL / - - - / - - -- ING" [Perhaps BARWELL - - - BIRMING. Could size be in centre? 3 3/4 IN?] Stamped on side [motif] (undecipherable) flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, john chance, loch ard, mutton bird island, glenample, eva carmichael, tom pearce, james barwell, cow bell, horse bell, bell founder, bell smith, vintage bell, birmingham bell foundry, farmer, shepherd, drover, stock bell

The subject item is a saw blade sharpening clamp that attaches to a bench allowing the operator to sharpen the teeth on a saw with a file while keeping the saw blade in an upright position. Henry Disston (1819–1878) began his career as an American saw maker in Philadelphia. He emigrated from England in 1833 and started making saws and squares in 1840. In 1850, he founded the company that would become the largest saw maker in the world the ”Keystone Saw Works” on the Delaware River. Some five years later, Disston built a furnace possibly the first melting plant for steel in America and began producing the first crucible saw steel ever made in the United States. While his competitors were buying good steel from Britain, he was making his own, to his specification, for his own needs. Disston subsequently constructed a special rolling mill exclusively for saw blades. Over the following decade, the Disston company continued to grow, even while dedicating itself to the Union Army's war effort. In 1865, when his son Hamilton Disston rejoined the business after serving in the Civil War, Disston changed the company's name to Henry Disston & Son. Henry Disston and his sons set the standards for American saw makers, both in terms of producing high-quality saws and developing innovative manufacturing techniques. Disston also started making files in 1865. In September 1872, Henry Disston and two other men dug a part of the foundation for what was to become the largest saw manufacturing facility in the world: Disston Saw Works. This was in the Tacony section of Philadelphia. Having previously moved his expanding business from near Second and Market Streets to Front and Laurel Streets, Disston sought to establish his business away from this cramped area. It took over 25 years to move the entire facility to Tacony. This Philadelphia neighborhood seems to have been the only company town in the United States established within an existing city. At its peak of operations, Disston Saw Works employed 8,000 people and the factory covered 300 acres. The company, known as Henry Disston and Sons, Inc by the early 20th century, cast the first crucible steel in the nation from an electric furnace in 1906. The firm's Armour plate building near Princeton Avenue and Milnor Street contributed tremendously to the World War II effort. But the company's innovation and industriousness would not last forever. In 1955, with mounting cash-flow problems and waning interest on the family's part to run the firm, Henry Disston and Sons were sold to the H.K. Porter Company of Pittsburgh. Porter's Disston Division was sold in 1978 and became the Henry Disston Division of Sandvik Saw of Sweden. This division was then sold in 1984 to R.A.F. Industries of Philadelphia and became known as Disston Precision Incorporated, a maker of specialized flat steel products. In 2013, R.A.F. Industries sold Disston Precision Inc. in a private sale. Although the company has ceased making Disston handsaws, the Disston brand name still exists in this firm. A significant American company that pioneered the making of high-quality steel and saws along with other tools and accessories. The subject item is significant as it was made at a time when the company was in its hay day. Adjustable Ball & Socket Saw Sharpening vice, cast iron, with clamp to attach to a workbench. Made by Henry Disston & Co. No 1 painted greyflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, saw clamp, henry disston & sons, saw sharpening, tool accessories, wood saws

This item is part of the Di Reidie collection. Diane Reidie was a much loved volunteer and President of Brighton Historical Society from 1999 until 2016. Originally from New Zealand, Di and her family lived in Male Street, Brighton for many years. A vibrant and energetic person with a zest for life and a gift for bringing people together, Di was a friend to many in the Bayside community and active in local community organisations. Her tireless work as President of BHS saw her named Bayside Citizen of the Year in 2008. As a seller and collector of vintage clothing, she was passionate about fashion history; one of her many enduring contributions to BHS was her extensive work in preserving, developing and promoting the Society's costume collection. In 2018-19, Di donated more than one hundred items from her personal vintage clothing collection to the Society. The collection, which includes clothing, hats, handbags and shoes from local and international designers, is representative of Di's wide-ranging interests, colourful personality, creativity, humour and love of fashion and travel. Di purchased these 1890s shoes around 1990 and recalled wearing them to approximately three events before she donated them to BHS in 2019. Di enjoyed the novelty and conversation they would inspire due to their unusual appearance by modern standards. The shoes are indicative of Di's playful approach to clothing and life. The decorative preserved mink pelt with head featured on the vamps of these shoes is typical of Victorian era interest in and prevalent use of preserved animals for decorative purposes in clothing, millinery and household adornment. This fashion reflected social positioning of oneself as being affluent, educated and worldly. Following the death of Queen Victoria's husband Prince Albert in 1861, the Queen's approach to mourning his death influenced social conventions for the public, with the wearing of black becoming a significant aspect of Victorian fashions. The shoes were made by Kendal Milne & Co, a large department store on Deansgate, Manchester. It has traded under various names and owners since it opened in 1832; it traded as Kendal Milne & Co from 1862-1919, and continued to be known by this name for many years after. The store is currently owned by the House of Fraser department store chain and is known as House of Fraser Manchester.Black silk linear quilted uppers of single piece construction with feature centre front vamp seam. Horsehair wadding can be seen along the side of the forefoot where the upper is coming away from the leather soles. Approx 4.5 cm plain black silk covered heel with leather top piece missing from right shoe. Both shoes feature the head of a small preserved mink with glass eyes. The toppling of the vamp features a decorative strip of mink fur. Inside of both shoes is a gold printed manufacturers label on the black silk insole.Manufacturers label - Made expressly for Kendall Milne and Co, Manchester.victoriana, mink pelt, taxidermy, 1890s, fur, di reidie, vintage clothing

People in ancient civilisations smoked pipes during various healing and religious ceremonies. By the end of the 15th century, after tobacco was discovered in America, smoking had become a common pastime for everyday people. From that time, tobacco pipes were fashioned from many materials ranging from gold and silver to corn cobs and clay. A popular material was meerschaum, an expensive, soft, white stone from Turkey. In the 1820s, French craftsmen carved pipes out of the wood from the growth on the root of a Mediterranean White Heath. This material became increasingly popular due to its durable, heat-resistant qualities. The growth was called ‘bruyere’, now anglicised to ‘briar’ wood. Bakelite was the first plastic made from synthetic components. It was developed by Leo Baekeland of New York in 1907. The material was heat-resistant and could be moulded into any shape and hardened to keep its shape. This invention greatly impacted the industrial world and the products available to the domestic market, making more objects available at reduced cost.This smoker's tobacco pipe symbolises one of the leisure activities of the early 20th century that has continued into modern times. The shape and materials of the pipe represent a point in time in the evolution of tobacco pipes, including the revolutionary impact that the 1900s invention of Bakelite had on objects available in the domestic and industrial markets.Smoker's tobacco pipe; a round brown wooden pipe bowl joined to a dark brown mouthpiece. The French pipe's bowl is made from briar wood, and its mouthpiece is Bakelite. There is an inscription on the pipe."French Briar Pipe"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, smoker's pipe, tobacco pipe, briar wood pipe, wooden pipe, smoking, french pipe, bakelite, smoker's equipment

Certificate is of the pledge that the brigade made to His Royal Highness the Duke of Edinburugh at a dinner that the Duke attended at the Ballarat Fire Station on 10th December 1867 during a royal visit to the district. White timber framed pledge from the Ballarat Fire Brigade to His Royal Highness the Duke of Edinburugh during his royal visit in December 1867. Pledge is on white paper with a coat of arms near the centre at the top of the page. Lettering is mainly in black ink with some red coloured letters being used. Certificate has a light brown coloured border around it with a hand drawn scrolled decorative edge made in gold colour. To His Royal Higness / The Duke of Edinburugh / May It Please Your Royal Highness / We Othe fficers and Members of the Ballaarat Fire Brigade, an institution based upon pure philanthropic / principles, our motto being "We Strive to Save" bear to approach your Royal / Highness with feelings of devotion and attachment, and deep felt gratitude to the Almighty, for this / opportunity of envicingour loyalty to Her Most Gracious Majesty Queen Victoria, your Royal / Mother: and, of tendering a hearty Firemans welcome to Your Royal Highness, in the land of our / adoption, and the good town of Ballaarat East, our residence. / We are deeply impressed with the great honor and importance of your Royal Higness's visit to the / Australian Colonies, and beg to express our fervent wishes for your Royal Highness's safe return / to our mother country. / We have the privilege and honor, to subscribe ourselves your Royal Higness's most obedient and humble / servants. / On behalf of the Brigade / Charles Dunn, Captain Carl Franz, Lieutenant / R. Geilhofer, Hon. Secretary / Ballaarat, December, 1867ballarat fire brigade, queen victoria, his royal higness, the duke of edinburugh, december 1867, 1867, captain charles dunn, captain dunn, lieutenant carl franz, lieutenant franz, honourary secretary r geilhofer, his royal highness the duke of edinburugh

The blouse was made in Greece about 1945. The method used to create this fine embroidery was to copy a design from a cross stitch embroidery book guided by fine white tapestry threads tacked onto the yolk; when the design was finished, the embroiderer would pull out each fine white tapestry thread until only the embroidery remained around the yolk of the blouse.Throughout the centuries and up until the 1970s-80s, the women of Ithaca spun, wove, embroidered and knitted. Mothers prepared their daughters' 'glory boxes' trousseau (prikia), weaving bedspreads, rag mats (koureloudes) for everyday use, finer wool rugs for formal use, as well as linen sheets, pillowcases, blankets, towels and tablecloths. Linen was also woven to make the mattress that the young brides would take to their future homes. Mothers also wove and embroidered the fabric for their daughters' underwear and petticoats, nightgowns, etc. Sewing of the garments was also done by hand. The girls embroidered handicrafts using various stitches, they crocheted lace, netted pillows and even linen carpets. The handicrafts were usually embroidered by hand in cross-stitch using linen and cotton fabric. At the time there were merchants who travelled to the villages to sell machine made goods for the trousseaus, but most of the dowries consisted of the beautifully crafted work of the women. In the 30's the SINGER Company came to Ithaca and taught the girls sewing on the machine. A handwoven silk blouse. Colour - ecru. Hand embroidered, hand sewn, very fine white tapestry was tacked round the yolk; a gusset was sewn under each short puff sleeve at the armpit; two-tone hand made silk thread cords were passed through the hollow border of the sleeves and neckline.

UnknownLight Weight bomb is made from 3 parts. The cylinder head section made of light steel screws onto the main body which is Aluminium and has a cylinder shape and screwed to the body section is a tin fin sectionSome what appears to be Japaness writing on the heads sectionlight weight bomb ww2

Dark grey nib holder made of metal. It is shaped into a cylinder with one end cut on an angle. There are two slots on the sloped end to hold the nib. Printed into the metal is: Koala Series Accommodation Holder. Made in Australia. Handle is missing.

Mr JH Quinton of Olinda, Victoria had the unusual hobby of carving coconut shell. Over a 50 year period he carved thousands of curios and household articles. Supplies of coconuts were sent to him by his brother in Singapore. Known in the Dandenong Ranges as "The Coconut King", he carved many series, including Australian animals, likenesses of hundreds of men prominent in public life, tableaux of sporting activities, including a series depicting cricket strokes, a coconut tea set, butterflies, buttons and boxes. Mr Quinton was an engraver and his considerable can be seen in the fine detail and sense of movement he was able to capture in his carvings.Decorative cube shaped box made from small tiles made from coconut shell. Brown in colour with a hinged lid. Additional carved decoration comprising acorns, flower and butterfly. Inside lid lined with red velvet.jh quinton, coconut shell, carving

Cloth shoulder patch to indicate that the conductor of the tram was qualified as a "Conductor Trainer". Made on black cloth backing, red stitching on the edge and the words "Conductor Trainer" stitched in red cotton. Presumed made by the uniform clothing section at Hawthorn.trams, tramways, mmtb, clothing, badges, uniforms, training

This Stanley plane was used in the making of components for the ship model Sovereign of the Seas. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This plane is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This plane was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Plane, No 120, made in USA by Stanley. This small plane is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”."Stanley", "USA", "No. 120"flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, wood working tool, plane, stanley of usa, sovereign of the sea, ship model, hobby, ship model tool

51 NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs Puffing Billy Service History or Notes Coupled Length 31 feet 4 inches (9550 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 2 inches (2794 mm) Weight 8 tons Capacity 24 passengers, or 20 passengers and 3 wheelchairs, or 16 passengers and 6 wheelchairs Number Built 2 In use 2 In 1981 the first of two extended NBHs with provision for wheelchair passengers (double door access and fold-up seats) was built, the second following in 1983. These were numbered 51 & 52 - a separate number series because of their length made them different from the other NBHs. May 2016 - In for repairs to the roofHistoric - Puffing Billy Railway Narrow Gauge - Passenger Rolling Stock: Excursion Car specially built for Wheelchairs access51 NBH - Excursion Car for wheelchairs - specially built for Wheelchair access allowing it to carry 24 passengers or 20 passengers and 3 wheelchairs, or 16 passengers & 6 wheelchairs made of wrought iron and timber 51NBH

Typewriters pre date computers and were used by office workers eg. Secretaries for documents and letter writing. An inked tape was hit by the keys as it moved along which resulted in their imprint being copied onto paper. Multiple copies were made by inserting carbon paper between sheets of paper. The original was easily identified.Used in the Kiewa Valley.Large, heavy, hard plastic two toned grey typewriter. The keys board includes symbols for inches, pounds, dollars, cents and fractions. The margins and size of paper measurements are in inches.The keyboard slopes up to a vertical plane. On top the area is flat where there is a small gap which exposes the metal keys. The cylinder that holds and enables the paper to be moved is long with controls at each end and a large lever that returns the cylinder to the left. Behind the cylinder there is a compartment. The keys hit an inked tape (black or red and black) which forms an impression onto the paper. Mechanisms, using the correct buttons, enable margins etc. to be pre set. This typewriter sits 3 cm high from a base. Vinyl deep red/black cover sits on top covering top and sides to protect the typewriter from dust. It is homemade with 2 sides attached to 1 long piece.Front top left: "Royal" Back top right "Made in England" Back silver paper sticker on top left "For Supplies and Service / Business Equipment Pty Ltd typewriter. royal. office. secretary. writing. business equipment.

The main photograph of the battery, "Vivian" a 24 Head Stamper is now in Beaconsfield, Tasmania. The battery head stamper was made in 1862 for crushing gold ore for the "Newchum" mine at Pleasant Creek (now Stawell) Victoria. In 1933 the Chintock family used the Head Stamper to cruse tin ore in a mine at Blue Teir in north-eastern Tasmania. It is not know how or when "Vivian" the battery head stamper came to Tasmania. In 1993 the battery was restored as is a working exhibit in the museum at Beaconsfield Tasmania.Two colour photographs, one of the Battery and the other information about the Battery. The main photograph of the battery, "Vivian" a 24 Head Stamper now in Beaconsfield, Tasmania. The battery head stamper was made in 1862 for crushing gold ore for the "Newchum" mine at Pleasant Creek (now Stawell) Victoria. Beaconsfieldstawell, mining

Made in Ballarat The latest in a series of events including recitals and masterclasses. Patron David Hobson, this program was devised by Graeme Vendy. President of the Arts Foundation Val Sarah.3 pages cover with image of hands playing violin, the program, and insert on blue paper with programme of musical items.Orchestral MASTERCLASS 21st June 2008 ... etc MADE IN BALLARAT Concert 2.30pm 22nd June 2008 The Ballarat Symphony Orchestra - Conductor Benjamin Northey With - David Hobson, Roger Lemke, Jacqueline Dark Accompanist - Wendy Rechenberg ... etc.orchestral, made in ballarat, 2008, the ballarat symphony orchestra, benjamin northey, david hobson, roger lemke, jacqueline dark, wendy rechenberg, opera, singing, singer, orchestra, ballarat

This is a superbly crafted cartographic mapping instrument. It is housed in its own high-quality purpose-built oak box. Made in the Netherlands from 1950 onwards. This instrument is from c 1956. it is a very high-quality military grade stereoscope that was generally used by photographic interpreters such as intelligence analysts but was equally useful for mapping activities. The stereoscope was used to examine 3D aerial photographic images. This instrument has a particularly useful capability to scan over the 3D stereo model using X and Y movement knobs, rather than having to physically move the aerial photographs. In the public and private sector it was also useful for photogrammetric interpretation for Forestry and Agricultural purposes. See also Bendigo RSL Collections Victoria item Number 6205.6P that shows the Old Deft Stereoscope in use at the Army Survey Regiment, Bendigo.This is an "Old Delft" scanning stereoscope with its reflecting carriage and legs. The Stereoscope is housed in its own purpose built wooden oak box that has dovetail joints, 2 x securing clips, 2 x handles and a lock (without key). The instrument is assembled by inserting colour coded legs into their matching slots."OLD DELFT SCANNING STEREOSCOPE ODSS III" "Patents Applied for" "OLD DELFT C4790" "MADE IN THE NETHERLANDS"royal australian survey corps, rasvy, fortuna, army survey regiment, army svy regt, asr

John Glass Cramond 1829 and James Dickson 1831-1910 were founders of a large drapery store. Both were Scots and both came separately to Australia in 1852. Cramond initially came for gold but soon opened a store in St Kilda with a post Office attached and he was the first post master there. Dickson was a farmer’s son but became a draper and while he was unsuccessful on the Bendigo diggings and then returned to Melbourne where he met Cramond and soon after they opened a store on Lonsdale Street. They opened their business in Warrnambool in 1855 as a general store with groceries, drapery and ironmongery. Both partners were involved with the community and James Dickson was an original director of the Warrnambool Woollen Mill 1909 and the Warrnambool Cheese and butter factory. He also served on the committee of management of Warrnambool Base Hospital. These coathangers were an everyday item from their store. A common item which provides a link to one of Warrnambool’s largest and longest running businesses.Wooden hangers with rounded corners and metal hooks, one plastic coated. Printed names engraved and painted in black with business name.Cramond & Dickson Tailors & Outfitters Warrnambool. 2 made on America and 3 made in Germany. 1 unmarkedcramond and dickson store, warrnambool

The photograph was taken during an opening on Ballarat Heritage Weekend. Colour image of stone and weatherboard building which was the initial shelter of the Learmonth Brothers who squatted at Ercildoun.The First House learmonth Bros (built 1837) made from hand split ? and hand made bricks. ?garden, ballarat heritage weekend, ercildoun, ercildoune, architecture

The photograph was taken during an opening on Ballarat Heritage Weekend. Colour image of stone and weatherboard building which was the initial shelter of the Learmonth Brothers who squatted at Ercildoun.The First House learmonth Bros (built 1837) made from hand split ? and hand made bricks. ?garden, ballarat heritage weekend, ercildoun, ercildoune, architecture

The photograph was taken during an opening of the Ercildoun property during Ballarat Heritage Weekend. Colour image of stone and weatherboard building which was the initial shelter of the Learmonth Brothers who squatted at Ercildoun.The First House Learmonth Bros (built 1837) made from hand split ? and hand made bricks. ?garden, ballarat heritage weekend, ercildoun, ercildoune, architecture, squatter, settlement