This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill

Kerosene was used to light the signal lamps at night time on a railway, to ensure that a locomotive driver could see that the line was clear there was no danger of another train ahead. This container was used to store the in kerosene to fuel such lamps and was kept inside a lamp room until required for use.Victorian Railways - Keroseane Container Used in the storage of kerosene prior to use in lamps at stations.Large, cylindrical tin container with conical lid and wire handle. A small zinc spout is embedded in the lower quadrant. The word 'KERO' is stencilled in white across the front. Keropuffing billy, kerosene, fuel, combustible material, tin container, lamps

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

Gangers Shed Desk A desk used in the Gang Shed for office work and other associated functions. Historic - Victorian Railways Permanent Way and Works - Gangers Shed Desk Gangers Shed Desk made of wood with wrought iron fittingspuffing billy, gangers shed desk, victorian railways

Ganger's Fire Beater This was used to beat the flames of a fire. They were used by track Gangers when burning off the trackside vegetation, to ensure the fires were kept under control. the canvis was dampened with water before useHistoric - Railways Permanent Way and Works - track equipment - Ganger's Fire Fighting Mop Ganger's Fire Beater made of timber handle with canvas strips attached puffing billy, fire beater

Hand Operated Rail Saw Out on the track in the old days, it was sometimes required to cut a piece of railway track. Before the use of generators and oxy cutting, the only way to do this was with a hand saw. This is the machine operated by two people, that would cut a piece of rail in half. And when the rail was cut, it was usually required to join it to another rail which required putting in 4 to 6 holes in the rail with a Hand Operated drill. Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Saw Hand Operated Rail Saw made of cast metalpuffing billy, hand operated rail saw

Light Rail Bender Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly. Historic - Railways Permanent Way and Works - track equipment - Light Rail Bender Light Rail Bender made out of cast wrought ironpuffing billy, light rail bender

Crank Handle for Saw Bench Crank Handle fornew record Saw BenchCrank Handle for Saw Bench made of cast metal 4N153puffing billy, crank handle, saw bench, new record saw bench

Railway tracks are produced straight. They may appear to be easy to bend and may appear flexible, but are required to be bent for curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this was required to be done with a manual rail bender. Sometimes referred to as a Jim Crow, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly.Victorian Railways Permanent Way and Works track equipment Light Rail Bender narrow GaugeCast iron semi-circular tool, with hooked ends and central screw shaft.puffing billy, rail bender, jim crow

Rail Turning Bar Rail is heavy, sometimes as much as 120 lbs per yard. To assist in being able to move rail, a special turning bar was developed. Usually a long handle, on one end various features in the head allow rail to be moved Historic - Railway Permanent Way and Works - track equipment - Rail Turning BarRail Turning Bar made from cast wrought iron puffing billy, rail turning bar

Ratchet Spanner This spanner is used on track work. Being a ratchet spanner, it allows movement in one direction, with a reverse movement to keep the tool in the same position, but it does not allow the item being tightened to rotate with the spanner in the reverse direction. This allows for longer handles and therefore gives more force to the item that is being tightened or released.Historic - Railway Permanent Way and Works - track equipment - Ratchet SpannerRatchet Spanner made of cast wrought iron puffing billy, ratchet spanner

Metal Pully and Rope When heavy items were required to be moved a rope and pulley set was very handy. By attaching one end of the set to a solid surface, it was possible to lift items. In the bush, the timber workers made good use of the pulleys. When set up in a sequence, they could move logs across gullys, up and down hills as the chopped down trees made their way to a sawmill. Using animal or mechanical power increased the use of the pulley and rope. Historic - Industrial - Metal Pulley and RopeMetal Pulley and Ropepuffing billy, metal pulley and rope

During early farming in Australia (before motorised whipper snippers) the hand held sickle was used to cut long grass, in this case in or around railway tracks. The inside of the blade's curve was sharp, so that the user can either draw or swing it against the base of the grass, catching the stems in the curve and slicing them at the same time. Historic - Railway Permanent Way and Works - track equipment - Grass SlasherWrought iron sickle with extended with wooden handle.puffing billy, extended sickle, farm tool, reaping hook, curved blade, grass cutting

Railway Track Tool Rail is heavy, sometimes as much as 120lbs per yard. To assist in being able to move rail, a special bar was developed. Using the handle as a lever, one section clamps onto the rail, allowing it to be moved. Historic - Railway Permanent Way and Works - track equipment - Railway Track ToolRailway Track Tool made of forged ironpuffing billy, railway track tool

Watering Can A watering can, with a large spout. Its former use is currently no known, but may have been used for oil, chemicals or even sand.Historic - Railway Permanent Way and Works - track equipment - Watering CanWatering Can with a large spout made of tin puffing billy, watering can

Van 8 NUU - Louvered Van Louvred Truck (11) (on u/frame of 110 NQR) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 8.VA - 20/ 7/1906 NWS Built new - / /1926 - To NU 8.VA - NU 8.VA - / 9/1928 - Modified AC Malco 21/12/1953 - Sold (to) Coulston & Hyder RS54/338 Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvred VanWooden Louvered Van on under frame of 110 NQR - Made of Timber on a Wrought iron frame - current condition Untrafficable8NUUpuffing billy, 110 nqr, 8 nuu - louvered van, victorian railways, 2'6" gauge, narrow gauge rolling stock

1NB - (1st Series) Saloon carriage (24) Body and underframe purchased by Puffing Billy Preservation Society from Pakenham In Active Service NB There were three types:- NB Class - Number Built (1st Series) 6 - Number Built (2nd Series) 17 - Number Built (3rd Series) 4 Nos. 1-6 were Saloon cars having end platforms and a ladies toilet, and were built from 1899-1904. Nos. 7-23 were 5-compartment side loading cars, built from 1906-1915. Nos. 24-27 were the former NAB class cars mentioned previously and were also side loading, having 6 compartments and two ladies toilets. VR Service History NBB 1.VA - 4/ 2/1899 NWS Built new - circa 1910 - To NB 1.VA - *NB 1.VA - / 2/1928 - Modified AC Malco BO 21/10/1930 NWS Into Workshops - 5/12/1930 NWS Out of Workshops (46 days) 30/ 1/1951 - Scrapped Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Saloon carriage (No. 1) Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection1NB Passenger Rolling Stock: Saloon carriage (No. 1) - Made of Timber and steel 1NBpuffing billy, 1nb, saloon carriage, victorian railways, narrow gauge passenger rolling stock, 2'6" guage

14NB - Carriage (NB 2nd series) 6 compartments (40) Awaiting restoration NB There were three types: -Nos. 1-6 were Saloon cars having end platforms and a ladies toilet, and were built from 1899-1904. Nos. 7-23 were 5-compartment side loading cars, built from 1906-1915. Nos. 24-27 were the former NAB class cars mentioned previously and were also side loading, having 6 compartments and two ladies toilets. VR Service History *NB 14.VA - 16/12/1912 NWS Built new - / 5/1926 - Modified AC Malco 15/ 7/1931 NWS Into Workshops - 20/10/1931 NWS Out of Workshops (98 days) 5/ 8/1936 NWS Into Workshops - 6/11/1936 NWS Out of Workshops (94 days) 26/ 2/1951 - Scrapped - Body and underframe purchased by the Puffing Billy Preservation Society from Pakenham.Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: NB Passenger carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection Passenger Rolling Stock: Passenger carriage 14NB - Carriage (NB 2nd series) 5 compartments - Made of Timber on a Wrought iron frame Awaiting restoration14NBpuffing billy, 14nb, nb passenger carriage, 2'6" guage, victorian railways, narrow gauge passenger rolling stock

NB Class - Number Built (1st Series) 6 - Number Built (2nd Series) 17 - Number Built (3rd Series) 4 26 NAC - Former NB Class (3rd Series) - Carriage 3 compartments and van (24 pass.) In Active Service - Belgrave Station Yard NAC COMBINED NB PASSENGER CAR AND GUARD'S VAN. A compartment NB which has had a guard's compartment temporarily added in one end. Due to the temporary nature of the guard's compartment, this vehicle retains its number in the NB numbering sequence, but has been classed NAC to differentiate it from the standard NBC. The use of the A is a recognition of the car's original NAB classification. VR Service History NABAB 2.VA - 1/ 7/1907 NWS Built new - circa 1910 - To NAB 2.VA - *NAB 2.VA - circa 1910 - Reference Photo SL20 p20 20/ 8/1923 FTG To NB 26.VA - NB 26.VA - /12/1927 - Modified AC Malco BO 27/ 9/1934 NWS Into Workshops - 30/10/1934 NWS Out of Workshops (34 days) 17/12/1954 - Scrapped Body to Eng. Spcl Works, RS55/707 Purchased by the Puffing Billy Preservation Society as a body & underframe. Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passsenger carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection Passenger Rolling Stock: 26 NAC - Passenger carriage - Made of Timber on a Wrought iron frame 3 compartments and van (No. 26)26 NAC puffing billy, 26 nac, nac passenger carriage, victorian railways, narrow gauge passenger rolling stock, 2'6" guage

10NBH Carriage - Excursion Car In Active Service - Belgrave Station Yard NBH SECOND-CLASS EXCURSION CAR. The H was recognising their use for "Holiday" traffic. 15 of these cars were built in 1919 and numbered 1-15. Two more were built in 1981, and numbered 16 & 17. Two extended versions for wheelchair passengers were built in 1981 & 1983. These were numbered 51 & 52 - a separate number series due to the different type of vehicle. Six, numbered 18-23, were built in 1997-98. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 18NBH entered traffic 19/4/1997; 19NBH on 5/12/1997; 20NBH on 19/12/1997, the others added in 1998. VR Service History : *NBH 10.VA - 8/12/1919 NWS Built new - /12/1928 - Modified AC Malco BO circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Excursion Car Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collection10 NBH Passenger Carriage - Excursion Car made of steel and timber10NBHpuffing billy, 10nbh, nbh - excursion car, victorian railways, victorian railways narrow gauge - passenger rolling stock

Van 2NBC - 1 compartment and van (7 & 4 ton capacity) In Active Service - Belgrave Station Yard NBC COMBINED SECOND-CLASS PASSENGER CAR AND GUARD'S VAN. Six cars, numbered 1-6, were built during 1898-1905 and originally classed NBDBD. The D was previously the letter code for Brakevans/Guard's Vans, but was changed to C when the double-letter code was dropped in 1910. A final NBC numbered 7 was added to the fleet in 1910. VR Service History : NBDBD 2.VA - 3/10/1899 NCL Built new - circa 1900 - Photograph R101: as N2BDBD circa 1910 - To NBC 2.VA - *NBC 2.VA - / 5/1926 - Modified AC Malco circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger and Guard's Van carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection2NBC - Combined Second-Class Passenger Car And Guard's Van. - Made of Timber on a Wrought iron frame 2NBC - 1 compartment and van (7 & 4 ton capacity)2NBCpuffing billy, 2nbc, 2nbc - combined second-class passenger car and guard's van, victorian railways, narrow gauge passenger and guard's van rolling stock, 2'6" guage

NC Van The NC guard's vans were originally classed NDD. In the 1910 reclassification they were classified NC. Apart from the windows and height they were externally the same as the NBC vans. Inside there were benches along both side walls. One end was equipped with a small guard's compartment. This had two corner seats, two desks with ticket selling windows and a letter rack. A novel feature was a folding dog cage under one of the benches. Six NC Brake Van / Guards Vans were built by Victorian Railways 1 NC was built in 1909 as NDD and reclassed 1NC in 1910. 2 NC was built and placed into service Nov 1912 3 NC , 4 NC and 5 NC were built and placed into service June / July 1914 6 NC was Built and placed into service in 1919 1 NC, 4 NC and 6 NC were all scrapped by Victorian Railways between 1954 and 1957 Van 5NC - Brake Van (4 ton capacity) In Active Service - Belgrave Station Yard VR Service History: 5 NC *NC 5.VA - 31/ 7/1914 NWS Built new - / 6/1926 - Modified AC Malco 16/11/1932 NWS Into Workshops - 9/12/1932 NWS Out of Workshops (24 days) 23/10/1935 NWS Into Workshops - 19/11/1935 NWS Out of Workshops (28 days) 10/ 8/1939 NWS Into Workshops - 8/ 9/1939 NWS Out of Workshops (30 days) 2/ 6/1944 NWS Into Workshops - 25/ 8/1944 NWS Out of Workshops (85 days) 21/ 4/1949 NWS Into Workshops - 14/10/1949 NWS Out of Workshops (178 days) Dec 2016 - Puffing Billy Register of Rolling Stock NC 5 Brake Van (4 ton capacity) - In traffic Historic - Victorian Railways - Narrow Gauge Rolling Stock - NC Brake Van Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock CollectionBrake Van (4 ton capacity) made of Timber and wrought iron5NCpuffing billy, 5nc, 2'6" gauge, victorian railways, 5nc brake van

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 92NQR - Goods Vehicle - Open Medium Truck NQ/NQR OPEN MEDIUM TRUCKS. 218 of these goods vehicles were built between 1898 and 1914 numbered 1-218. Originally, these wagons carried the code letter R as they were built with sides and ends. Some later had the R removed if they regularly ran as flat wagons without theh sides and ends. Over the years, a number of NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames. 92 NQR VR Service History : *NQR 92.VA - 2/ 3/1907 NWS Built new - / /1926 - To NQ 92.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck with drop ends Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 92NQR - Open Medium Truck with drop ends made of Steel and metal92NQR puffing billy railway, pbr, rolling stock , 29 nqr, narrow gauge rolling stock, victorian railways, nqr wagon

149NQ - Water Wagon - Water Truck (2000 gallons) In Traffic NQ WATER TRUCK. This vehicle (No. 149) is an NQR without sides and with a 2000-gallon (9000-litre) water tank fitted. Over the years of V.R, operation a number of NQs were fitted with water tanks, but retained their NQ code and number. (For a number of years this vehicle carried the classification NWT but retained its number in the NQ numbering sequence). VR Service History : *NQR 149.VA - 24/ 9/1910 NWS Built new - / /1926 - To NQ 149.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - Water truck (No. 149) Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 149 NQ - Water Wagon - Water Truck (2000 gallons) made of Steel and metal149 NQpuffing billy, victorian railways, narrow gauge rolling stock, nq water wagon, 149 nq

10 NU Louvre Van - Louvred Truck (11) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 10.VA - 30/12/1911 NWS Built new - / /1926 - To NU 10.VA - NU 10.VA - / 5/1926 - Modified AC Malco /12/1972 BEL To NW 10.VA Sec72/3400, RS72/9371 NW 10.VA - 26/ 8/1976 CLS Photograph #662.2-.4: and end detail 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 Build Date: 30/12/1911 NWS Built new Victorian Heritage Register (VHR) Number H2187 NW 10 is a 1972 reclassification of NU 10. It is presumed the van was used to store tools and equipment. In 1977, the van was removed from railway records and control handed to the Puffing Billy group.Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock CollectionWooden Louvered Van - Made of Timber on a Wrought iron frame - current condition Untrafficable10 NU puffing billy, louvered van, 10nu, victorian railways, 2'6" gauge, narrow gauge rolling stock

13 NMM ( 13 NM ) Livestock Van - Cattle Truck In traffic NMM CATTLE TRUCK. Four of these were built during 1899-1901 and eleven more were built during 1909 and 1917, a total of 15. They were numbered 1-15. VR Service History : NMM 13.VA - 5/ 6/1917 NWS Built new - / /1926 - To NM 13.VA - *NM 13.VA - / 8/1928 - Modified AC Malco Purchased by Puffing Billy Preservation Society. Sec 65/2711. RS 65/6012. "An NM (13) and pulpwood wagon .... for displayat Museum.....scrap value to be charged direct to the PBPS." 19/ 4/1967 BEL Sold (to) Puffing Billy Preservation SocietyHistoric - Victorian Railways - Narrow Gauge Rolling Stock - Livestock Van - Cattle Truck Victorian Heritage Register (VHR) Number H2187 - The Puffing Billy Rolling Stock Collection 13 NMM Livestock Van - Cattle Truck made of wrought iron and timber13 NMMpuffing billy railway, puffing billy, victorian railways, nmm cattle truck, 13 nmm

8 NBH - Excursion Car (28) In Active Service - Belgrave Station Yard 8NBH - Excursion carriage. This car has been restored to original condition with white canvas weather blinds,Full carriage length side steps, timber tongue and groove boards,coupling centering springs and some pinch gas lighting equipment. NBH SECOND-CLASS EXCURSION CAR. The H was recognising their use for "Holiday" traffic. 15 of these cars were built in 1919 and numbered 1-15. Two more were built in 1981, and numbered 16 & 17. Two extended versions for wheelchair passengers were built in 1981 & 1983. These were numbered 51 & 52 - a separate number series due to the different type of vehicle. Six, numbered 18-23, were built in 1997-98. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 18NBH entered traffic 19/4/1997; 19NBH on 5/12/1997; 20NBH on 19/12/1997, the others added in 1998. VR Service History : *NBH 8.VA - 8/12/1919 NWS Built new - / 1/1929 - Modified AC Malco BO circa 1955 - Condemned Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Excursion Car 8NBH - Passenger Carriage - Excursion Car made of steel and timber8NBHpuffing billy, victorian railways, 8 nbh, passenger carriage, excursion car, narrow gauge

1 NAL - Mt. Lyell - (Mt. Lyell) O 5; 1 NBL - 1st. class saloon car (20) In Active Service Puffing billy railway NAL FIRST-CLASS SALOON CAR. Four saloon end-platform cars originally built during 1901–1902 by the Lancaster Railway Carriage and Wagon Company Ltd. for the 3'6" gauge Mt. Lyell Mining & Railway Company in Tasmania and classed O. Converted for use as second-class cars on the 2'6" gauge Puffing Billy Railway during 1965–1966, these cars were reclassified NBL and numbered 1–4. The L recognises their Mt. Lyell origin, No. 1 was kept for use as the Railway's VIP car and was reconditioned to a higher standard. No. 2 was similarly upgraded in 1985 for use on special occasions. In 1989 No. 3 was similarly reconditioned with No. 4 receiving similar treatment in 1995. These cars were re-classified NAL in recognition of their new first-class nature. The Mt Lyell Railway was closed in 1963 and subsequently dismantled, but fortunately several of the locomotives and carriages passed into preservation. This original Mt Lyell Railway passenger carriage was donated to the Puffing Billy Preservation Society by the Mount Lyell Mining & Railway Company in the 1960s and was converted to 2' 6" gauge. It has since given many years of service on the Puffing Billy Railway. TASMANIAN CARRIAGES & GUARDS VANS No. Builder Type Year built Ex. Location Note NAL 1 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Mt Lyell NAL 2 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Rinadeena NAL 3 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Teepookana NAL 4 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Dubbil BarrilHistoric - Industrial Narrow Gauge railway - Mt. Lyell Mining & Railway Company in Tasmania - 1st Class Saloon Carriage 1st. class saloon car made of Timber and Steel1 NAL - Mt. Lyell

2 NAL - Rinadeena - (Mt. Lyell) O 2; 2 NBL - 1st. class saloon car (20) NAL FIRST-CLASS SALOON CAR. Four saloon end-platform cars originally built during 1901–1902 by the Lancaster Railway Carriage and Wagon Company Ltd. for the 3'6" gauge Mt. Lyell Mining & Railway Company in Tasmania and classed O. Converted for use as second-class cars on the 2'6" gauge Puffing Billy Railway during 1965–1966, these cars were reclassified NBL and numbered 1–4. The L recognises their Mt. Lyell origin, No. 1 was kept for use as the Railway's VIP car and was reconditioned to a higher standard. No. 2 was similarly upgraded in 1985 for use on special occasions. In 1989 No. 3 was similarly reconditioned with No. 4 receiving similar treatment in 1995. These cars were re-classified NAL in recognition of their new first-class nature. The Mt Lyell Railway was closed in 1963 and subsequently dismantled, but fortunately several of the locomotives and carriages passed into preservation. Purchased by the Puffing Billy Preservation Society from the Mount Lyell Mining & Railway Company in the 1960's and converted to 2' 6" gauge. It has since given many years of service on the Puffing Billy Railway. TASMANIAN CARRIAGES & GUARDS VANS No. Builder Type Year built Ex. Location Note NAL 1 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Mt Lyell NAL 2 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Rinadeena NAL 3 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Teepookana NAL 4 Lancaster Railway Carriage and Wagon Co Saloon 1901 Mt Lyell Railway Named Dubbil BarrilThe Rinadeena is a stunning example of a classic narrow gauge 1st Class Saloon Carriage, used as a luxury edition to train travel in the late 1800s and the 2NAL within Puffing Billy's collection was purchased by the Puffing Billy Preservation Society in the 1960s, where it underwent restoration to become part of the railway's historic transport collection.A timber and iron saloon car - painted in crimson with a name plate 'Rinadeena' attached to the centre of the carriage and the words '2 NAL' painted in white directly below. The word 'FIRST' is painted in gold at both ends of the carriage. The car has nine windows on either side of the carriage and a wrought iron ballastrade upon entry at eiether end of the carriage as well as iron steps to ascend. Inside the carriage are 10 bench seats made of wood and leather and ten tables for dining. The windows are adorned with cream cloth fabric and above each bench are wrought iron luggae racks. The ceiling is covered in cloth and features two suspended ornate glass and metal light fixtures. A wooden door with two glass panels can be found at both ends of the carriage.2 NAL - Rinadeenarailway carriages, first class saloon, narrow gauge, rinadeena, mt lyell, transport, travel, leisure, luxury