Notices to cable tram employees and signalmen about the operation of the intersection of Collins and Swanston Street c1921. Details how Police would signal for the number of trams to cross in either direction and how the signalman would operate the signals and the cable depression lever for Collins St cable cars. The Rules for signalmen dated 1/7/1921 and signed by J G Roberts, Manager Cable system for the MMTB. This intersection was one of the busiest in Melbourne running four separate routes in Collins St and the busy St Kilda Road route.Yields information about the cable tram operation of Swanston and Collins St and signalmen.Two foolscap photocopied sheets, stapled in top left hand corner.tramways, cable trams, swanston st, collins st, signalmen, police

Melbourne Tramway and Omnibus Co. Ltd Rules and Regulations by which all operational staff were to abide by. Provides separate sections of rules for Gripmen and Conductors, with Special rules for both roles, collection of fares and use of Bell Punch, transfer and check tickets, Collectors (Conductors acting as collectors on the dummy or grip car), signalmen and shunters. Printed by Sands & McDougall. Date of issue has been damaged by silverfish - Mr H A Wilcox was appointed Secretary in 1909, becoming General Manager in the Tramway Board which succeeded the private company in 1916. Rule 76, page 21 allows for the wearing of the Australian Tramway Employees Association union badge. The Union was recognised by the Company in August 1912 and the wearing of Union badges on watch chains was permitted. A possible date for the document is 1912. See item 6340 for the MTOCo / AETA agreement that was reflected in these rules.Demonstrates a MTOCo cable tram rule book and requirements of its employees.Book - 68 pages + card covers covered in a dark grey cloth, centre stapled.tramways, cable trams, conductors, tickets, grip men, signalmen, shunters, fares, operations, rules

Book or folder, printed card cover set of instructions titled "Standard Procedure covering the duties and responsibilities of all Uniformed and Plain Clothes Traffic Officers". Printed by the MMTB mid to late 1950's. Comprises: 1 - two pages of introduction and a fold out sheet showing the details of the Traffic Manager's department; 2 - Card divider labelled "District Inspectors" - 29 sheets listing duties and arrangements. Divisional Superintendents R. C. Drummond and J. H. Ritchie. 3 - Card divider labelled "Traffic Inspectors" - 19 sheets 4 - Card divider labelled "Revenue Inspectors" - 16 sheets 5 - Card divider labelled "Depot Starters" - 12 sheets 6 - Card divider labelled "Staff Signalmen" - 12 sheets 7 - Heavy card backing board. All sheets stapled at the top with two heavy staples.On the top of the cover in ink "Inspector de Dohse 52 Monash Street Box Hill"trams, tramways, mmtb, traffic officers, traffic staff, inspectors, district inspectors, ticket inspectors, revenue clerks, depot masters, signalmen

No other historical information is available. Green enamelled bronze badge fixed to a wooden plaque. Badge details an image of the Royal Australian Corps of Signal Sergeants Mess. Plaque affixed to front states: 'Presented to RAR Association Victoria From W01 I J Haycock Dec 87' ww2, royal australian corps of signals, signalmen

Metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Exterior casing of a black painted metal railway signal lamp with circular blue and red glass filters and a turning mechanism on the top under a circular handle. Small copper plate with the letters "A y" stamped on it, on one side of the lamp. "A y"railway lamps, signalling lamp, train signal lamps

Metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Black painted metal signal lamp with a circular metal cover over a clear glass disk at the front and an elongated oval shaped handle at the back. The circular metal cover has a vertical slit in it. There is an inscription on the top of the lamp with the date 1917 and the company name "Eli Griffiths & Sons, Birmingham"."ELI GRIFFITHS & SONS / 1917 / BIRMINGHAM"railway lamps, signalling lamp, train signal lamps, railway equipment

These types of metal and glass railway signalling lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The three railway signalling lamps have local significance as a set donated by a resident of Wodonga who worked for the Victorian Railways, as well as national significance as examples of the communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Set of three painted black metal and glass railway signal lamps used for various purposes during train journeys. The largest signal lamp has circular blue and red glass filters and a turning mechanism on the top under the handle. "A y" on a small copper plate on one side of the largest signal lamp - Lamp 1.railway lamps, signalling lamp, train signal lamps

These types of metal and glass railway signal lamps were used for communication, safety and lighting by train guards, shunters and signalmen, as well as station staff in the late 1880s to the early 1900s. They were hand operated and used fuel such as kerosene.The railway signal lamp has local significance as part of a set of three lamps donated by a resident of Wodonga who worked for the Victorian Railways. It also has national significance as an example of communication and safety equipment used by the railways in Australia in the late 19th century and early 20th century.Black painted metal signal lamp with a clear glass lens secured at the front and one thin elongated oval shaped handle showing at the back. The metal appears to be tin plated iron under the black paint layer. There is an oval plate with an embossed inscription on the proper left side of the lamp that is partly covered by the door at the front which holds the clear glass lens. The inscription includes the date 1901."...NARIPPINGILLE STOVE / CO LTD 1901 / PATENT...S & / ...NUFACTURERS / RMINGHAM" on an oval shaped plate on the proper left side, which is partly covered by the door with the clear glass lens.railways wodonga, victorian railways

Possibly used in the Orbost district. Railway lamps of this kind were hand signalling lamps used by train guards, shunters and sometimes signalmen and station staff. They could signal the locomotive crew at night to let them know what to do (move forward/move backward/right-of-way) when leaving a station, goods yard or siding. Railway lamps of this kind were significant railway items in their period of use as essential tools to the safe-working operations of the railway. Two railway signal lamps. These are kerosene burning lamps made of metal and painted red. Both lamps have carrying handles at the top. .1 has a green glass lens and .2 has a red glass lens. signals lamps communication railway transport kerosene-burning

Notice - duplicated foolscap sheet titled "Notice to Employees - Staff Signalman and Ticket Examiner Relief Depot Starter", calling for applications for the positions, gives salary range, conditions, closure date for applications. Dated 30/6/1977. Signed by W. Aird Secretary.trams, tramways, signalmen, mmtb, inspectors, officers, wages

Typed instruction - quarto sheet - "St Kilda Junction Signal Box Procedures" - could be a copy of the actual instructions provided in the signal box - gives what the AM and PM shifts were required to undertake. Has a poem on the based that was affixed to the wall of the signal box. On the bottom section has the address of Mr. Noel Gippstrams, tramways, st kilda junction, instructions, signalmen, signals, poem

Digital image of "Electric Tram Driver's Certificate No. 407", issued to D. (Daniel) Patience, signed by G. Barker Instructor, with "A. W. Murdoch" stamp authorising the document, dated 23/3/1929. Donated by Betty (daughter - aged 90) and Cheryl Williams (grand daughter) of Daniel. Reported to have been the first driver leaving the then new Camberwell depot. Born in Avoch Scotland, was a police constable there, before emigrating to Melbourne. Was a cable tram Gripman in the Albert Park Area. Became an electric tram driver, then signalman at St Kilda Junction and trained as an inspector, but did not like the green uniform. Ran in the Stawell Gift of 1925 (injured foot during the race), was a Navigator on Transport RAF/RAAF flights during WW2. War memorabilia to the War Memorial Canberra. Cheryl advised 26/11/2019 - My grandfather was born 2nd June 1903 and died 11th Nov 1977.trams, tramways, drivers, gripmen, camberwell depot, signalmen, certificates

Coloured postcard of the Melbourne Town Hall, Swanston, and Collins Sts. Has three cable car sets in the view, one with two trailers southbound in Swanston St. In the bottom right-hand corner can be seen a shelter and signalman for the control of the intersection. The card was printed in Germany.Yields information about the Melbourne Town Hall and a signal box.Colour postcard, divided back unused. Has number "09 871" in bottom right hand corner.tramways, collins st, swanston st, signalmen, trailers, cable trams, melbourne town hall

Instruction Book or Procedure Manual, 69 Foolscap page, Gestetner printed, contained within heavy card covers, top stapled (three staples), top sheet printed with title "Standard Procedure covering the Duties and Responsibilities of the Uniformed and Plain Clothes Traffic Officers". Compiled by the Melbourne and Metropolitan Tramways Board, first adopted 1957, revised December 1962. Has cover sheet signed by Traffic Manager, R. C. Drummond with six sections of procedures: 1. General 2. District Traffic Inspector's 3. Traffic Inspector's 4. Revenue Inspector's 5. Ticket Examiner - Depot Starters 6. Staff Signalmen (Batman Ave and Swanston/Victoria St.) On top of first sheet in black ink "Ballarat Tramway Preservation Society Catalogue No 314."trams, tramways, mmtb, instructions, rules, traffic control

Certificate presented to N C Boucher after retiring as President of the Tramway Division of the Australian Railways Union in 1947. Signed by A J Cregan as State President and J J Brown as State Secretary. The Union seal has been applied to the item. The Union had several divisions such as guards, signalmen, shunters etc. The Tramway Division represented the tramway depots at Elwood and Sandringham. The certificate includes a photo of the Union building, a train hauled by A2 945 and an Electric Train. The Union did not represent locomotive or electric train crews, these were represented by the Australian Federated Union of Locomotive Employees. For notes on Mr Boucher's career see item 7056.Demonstrates an ARU Illuminated address of the 1940sFramed Certificate - printed base on paper with name, position inked on over a light blue wash. Timber surround with gold surround and glazed.n c boucher, unions, vr trams, aru, certificates, illuminated address

Retyped Instruction - MMTB - C No. 388, signed by A. Simpson District Traffic Superintendent, NS&F, dated 8/7/1925, giving instructions for trams crossing William St lines and in particular Bourke and William St. Notes the duties of the Conductors, drivers, flagmen and policemen. Two copies held - one on a single sheet and one copy on two sheets of paper. Would appear to have been retyped from the original document.trams, tramways, cable trams, essendon depot, william st, instructions, flagmen, bourke st, conductors, signalmen

Electric staff - Electric staff instruments The staff and ticket system was still too inflexible for busy lines, as it did not allow for the situation where the train intended to carry the actual token was cancelled or running very late. To provide for this, the electric train token system was developed. Each single-line section is provided with a pair of token instruments, one at the signal box at each end. A supply of identical tokens is stored in the instruments, which are connected by telegraph lines. A Staff can be removed from one instrument only if both signalmen co-operate in agreeing to the release. Once a Staff has been removed, another cannot be removed until the token which is "out" is replaced in either instrument. (There are variations on this sequence of events.) By this means, it can be ensured that at any one time, only one token is available to be issued to a driver. Staff belonging to adjacent sections have different configurations to prevent them being inserted into the wrong instrument. Nevertheless, in the Abermule train collision in 1921 and lax working procedures allowed the safeguards provided by the electric Staff system to be circumvented; a driver was handed a Staff for the wrong section, and without reading the information listed on the staff, proceeded on the mistaken belief that the Staff was correct. To prevent this, it became a requirement in the UK for the signals controlling entry to the single line section (starting or section signals) to be locked at danger unless a token has been released from the relevant Staff instrument. Historic - Victorian Railways Electric Staff Instrument Electric Staff Instrument made of Iron , Brass and Glasspuffing billy, electric staff instrument, victorian railways

This three-dimensional Distant Signal is part of a Flagstaff Signal set of ball, cone and drum shapes. It has been woven and then fabricated with strong metal swivel fittings and loops for suspending from a high point on a flagstaff at a signal station or on a ship’s masthead. The cane signal was constructed to withstand all weather and to be visible from a long distance. The gaps between the woven cane allow air to pass through, minimising possible swaying. Similar sets were made from rope or fabric. Warrnambool's Flagstaff was erected in 1854. Its primary use was to display visual signals that could convey messages between land and sea. It was also used to notify the local population of the approach of ships. One of the popular signalling codes in use in the early-to-mid 1800s was the Marryat’s Code but there were others in use as well; there was no one standard code. In 1857 the International Marine Conference adopted an International Code of Signals as a standard communications system for all vessels that could be understood in many different languages. The Normanby Advertiser reported on June 5th 1857 a query from the Post Master General as to whether the request of the Chief Harbour Master would be carried out, in that Warrnambool would receive a new flagstaff and a set of Marryatt’s signal flags. The Table of Codes was published, showing how to use combinations of these flags to send messages. The Code was revised in 1887 to cover situations where distance, light, wind and weather conditions affected the visibility of the flags and prevented clear communication. The first report of the International Code of Signals Committee of 1897 warned signalmen not to rely on ordinary semaphore flags and introduced a Distant Signal Code using either particular semaphore flags or the three-dimensional shapes of a ball, cone and drum that aligned with the semaphore flag shapes of a circle, pennant and square. International Code of Signals In 1931, after World War I’s experiences in using signal codes, the International Code of Signals conference in Washington revised and published the rules for the conduct of signalling. One of the changes was that “the use of the Distant Signals and of fixed semaphore was abandoned”. It is of interest to know that modern marine law in many countries insists that a set of Day Shapes must be carried onboard vessels of a certain size. These highly visible geometric shapes are used at sea in daylight to communicate messages between vessels. They are used in a similar way to the Distant Signals, in that different combinations of shapes represent different messages. The set of shapes includes a ball, cylinder, cone and diamond. The shapes are hung between the top of the vessel’s foremast and the front of the vessel. They are only coloured black and are about 1.5 metres high. The vertical line of shapes can mean messages such as Boat not under command, Fishing, and Under sail and power.Distant Signals were an important means of marine communication from the late 1880s to the early 1930s, including during World War I. They were an advancement to the International Shipping Codes and safety. The cane signals’ shapes appear to be the same from whatever direction they are viewed, removing confusion about the message they convey. The same shapes continue to be used today for the sets of Day Shapes used as marine navigational signals that are mandatory on certain-sized vessels.Distant Signal Ball, part of a Flagstaff signal set. A round woven cane ball, painted black, with a metal rod passing through the centre. The rod has a loop at each end, then a concave, octagonal metal plate that rests on the outside surface of the ball, serving as a washer. The rod has swivels at each end.flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, distant signal, signal, maritime signal, ball signal, signal shape, flagstaff signal, signal station, masthead signal, communications, marine technology, signals, marine signals, flaghoists, international marine conference, international code of signals, signal codes, marine safety, signal flags, day shape, daymark, day symbol, navigation, warrnambool flagstaff, 1854, 1857 1931, 1887, 1897

This three-dimensional Distant Signal is part of a Flagstaff Signal set of ball, cone and drum shapes. It has been woven and then fabricated with strong metal swivel fittings and loops for suspending from a high point on a flagstaff at a signal station or on a ship’s masthead. The cane signal was constructed to withstand all weather and to be visible from a long distance. The gaps between the woven cane allow air to pass through, minimising possible swaying. Similar sets were made from rope or fabric. Warrnambool's Flagstaff was erected in 1854. Its primary use was to display visual signals that could convey messages between land and sea. It was also used to notify the local population of the approach of ships. One of the popular signalling codes in use in the early-to-mid 1800s was the Marryat’s Code but there were others in use as well; there was no one standard code. In 1857 the International Marine Conference adopted an International Code of Signals as a standard communications system for all vessels that could be understood in many different languages. The Normanby Advertiser reported on June 5th 1857 a query from the Post Master General as to whether the request of the Chief Harbour Master would be carried out, in that Warrnambool would receive a new flagstaff and a set of Marryatt’s signal flags. The Table of Codes was published, showing how to use combinations of these flags to send messages. The Code was revised in 1887 to cover situations where distance, light, wind and weather conditions affected the visibility of the flags and prevented clear communication. The first report of the International Code of Signals Committee of 1897 warned signalmen not to rely on ordinary semaphore flags and introduced a Distant Signal Code using either particular semaphore flags or the three-dimensional shapes of a ball, cone and drum that aligned with the semaphore flag shapes of a circle, pennant and square. International Code of Signals In 1931, after World War I’s experiences in using signal codes, the International Code of Signals conference in Washington revised and published the rules for the conduct of signalling. One of the changes was that “the use of the Distant Signals and of fixed semaphore was abandoned”. It is of interest to know that modern marine law in many countries insists that a set of Day Shapes must be carried onboard vessels of a certain size. These highly visible geometric shapes are used at sea in daylight to communicate messages between vessels. They are used in a similar way to the Distant Signals, in that different combinations of shapes represent different messages. The set of shapes includes a ball, cylinder, cone and diamond. The shapes are hung between the top of the vessel’s foremast and the front of the vessel. They are only coloured black and are about 1.5 metres high. The vertical line of shapes can mean messages such as Boat not under command, Fishing, and Under sail and power.Distant Signals were an important means of marine communication from the late 1880s to the early 1930s, including during World War I. They were an advancement to the International Shipping Codes and safety. The cane signals’ shapes appear to be the same from whatever direction they are viewed, removing confusion about the message they convey. The same shapes continue to be used today for the sets of Day Shapes used as marine navigational signals that are mandatory on certain-sized vessels.Distant Signal Cone, part of a Flagstaff signal set. A woven cane cone, painted black, with a metal rod passing through the centre and two crossed metal bars at the base. The central rod has a loop at the top and passes through the bars at the base, finishing in a metal loop. The rod has swivels at each end.flagstaff hill, warrnambool, flagstaff hill maritime museum and village, shipwreck coast, marine navigation, marine communications, communication signal, lifesaving, ship at sea, day shape, masthead signal, day signal, day mark signals, marine technology, safety equipment, navigation equipment, marine day shape, day marker, cane day shape, signal cone, day signal cone, cone signal, cone day shape, distant signal, flagstaff signal, signal station, communications, signals, marine signals, flaghoists, international marine conference, international code of signals, signal codes, marine safety, signal flags, daymark, day symbol, navigation, warrnambool flagstaff, 1854, 1857 1931, 1887, 1897

This three-dimensional Distant Signal is part of a Flagstaff Signal set of ball, cone and drum shapes. It has been woven and then fabricated with strong metal swivel fittings and loops for suspending from a high point on a flagstaff at a signal station or on a ship’s masthead. The cane signal was constructed to withstand all weather and to be visible from a long distance. The gaps between the woven cane allow air to pass through, minimising possible swaying. Similar sets were made from rope or fabric. Warrnambool's Flagstaff was erected in 1854. Its primary use was to display visual signals that could convey messages between land and sea. It was also used to notify the local population of the approach of ships. One of the popular signalling codes in use in the early-to-mid 1800s was the Marryat’s Code but there were others in use as well; there was no one standard code. In 1857 the International Marine Conference adopted an International Code of Signals as a standard communications system for all vessels that could be understood in many different languages. The Normanby Advertiser reported on June 5th 1857 a query from the Post Master General as to whether the request of the Chief Harbour Master would be carried out, in that Warrnambool would receive a new flagstaff and a set of Marryatt’s signal flags. The Table of Codes was published, showing how to use combinations of these flags to send messages. The Code was revised in 1887 to cover situations where distance, light, wind and weather conditions affected the visibility of the flags and prevented clear communication. The first report of the International Code of Signals Committee of 1897 warned signalmen not to rely on ordinary semaphore flags and introduced a Distant Signal Code using either particular semaphore flags or the three-dimensional shapes of a ball, cone and drum that aligned with the semaphore flag shapes of a circle, pennant and square. International Code of Signals In 1931, after World War I’s experiences in using signal codes, the International Code of Signals conference in Washington revised and published the rules for the conduct of signalling. One of the changes was that “the use of the Distant Signals and of fixed semaphore was abandoned”. It is of interest to know that modern marine law in many countries insists that a set of Day Shapes must be carried onboard vessels of a certain size. These highly visible geometric shapes are used at sea in daylight to communicate messages between vessels. They are used in a similar way to the Distant Signals, in that different combinations of shapes represent different messages. The set of shapes includes a ball, cylinder, cone and diamond. The shapes are hung between the top of the vessel’s foremast and the front of the vessel. They are only coloured black and are about 1.5 metres high. The vertical line of shapes can mean messages such as Boat not under command, Fishing, and Under sail and power.Distant Signals were an important means of marine communication from the late 1880s to the early 1930s, including during World War I. They were an advancement to the International Shipping Codes and safety. The cane signals’ shapes appear to be the same from whatever direction they are viewed, removing confusion about the message they convey. The same shapes continue to be used today for the sets of Day Shapes used as marine navigational signals that are mandatory on certain-sized vessels.Distant Signal Ball, part of a Flagstaff signal set. A round woven cane ball, painted black, with a metal rod passing through the centre. The rod has a loop at each end, then a concave, octagonal metal plate that rests on the outside surface of the ball, serving as a washer. The rod has swivels at each end.flagstaff hill, warrnambool, flagstaff hill maritime museum and village, shipwreck coast, marine navigation, marine communications, communication signal, lifesaving, ship at sea, day shape, masthead signal, day signal, day mark signals, marine technology, safety equipment, navigation equipment, marine day shape, day marker, cane day shape, signal ball, day signal ball, ball signal, ball day shape, distant signal, flagstaff signal, signal station, communications, signals, marine signals, flaghoists, international marine conference, international code of signals, signal codes, marine safety, signal flags, daymark, day symbol, navigation, warrnambool flagstaff, 1854, 1857 1931, 1887, 1897

This three-dimensional Distant Signal is part of a Flagstaff Signal set of ball, cone and drum shapes. It has been woven and then fabricated with strong metal swivel fittings and loops for suspending from a high point on a flagstaff at a signal station or on a ship’s masthead. The cane signal was constructed to withstand all weather and to be visible from a long distance. The gaps between the woven cane allow air to pass through, minimising possible swaying. Similar sets were made from rope or fabric. Warrnambool's Flagstaff was erected in 1854. Its primary use was to display visual signals that could convey messages between land and sea. It was also used to notify the local population of the approach of ships. One of the popular signalling codes in use in the early-to-mid 1800s was the Marryat’s Code but there were others in use as well; there was no one standard code. In 1857 the International Marine Conference adopted an International Code of Signals as a standard communications system for all vessels that could be understood in many different languages. The Normanby Advertiser reported on June 5th 1857 a query from the Post Master General as to whether the request of the Chief Harbour Master would be carried out, in that Warrnambool would receive a new flagstaff and a set of Marryatt’s signal flags. The Table of Codes was published, showing how to use combinations of these flags to send messages. The Code was revised in 1887 to cover situations where distance, light, wind and weather conditions affected the visibility of the flags and prevented clear communication. The first report of the International Code of Signals Committee of 1897 warned signalmen not to rely on ordinary semaphore flags and introduced a Distant Signal Code using either particular semaphore flags or the three-dimensional shapes of a ball, cone and drum that aligned with the semaphore flag shapes of a circle, pennant and square. International Code of Signals In 1931, after World War I’s experiences in using signal codes, the International Code of Signals conference in Washington revised and published the rules for the conduct of signalling. One of the changes was that “the use of the Distant Signals and of fixed semaphore was abandoned”. It is of interest to know that modern marine law in many countries insists that a set of Day Shapes must be carried onboard vessels of a certain size. These highly visible geometric shapes are used at sea in daylight to communicate messages between vessels. They are used in a similar way to the Distant Signals, in that different combinations of shapes represent different messages. The set of shapes includes a ball, cylinder, cone and diamond. The shapes are hung between the top of the vessel’s foremast and the front of the vessel. They are only coloured black and are about 1.5 metres high. The vertical line of shapes can mean messages such as Boat not under command, Fishing, and Under sail and power.Distant Signals were an important means of marine communication from the late 1880s to the early 1930s, including during World War I. They were an advancement to the International Shipping Codes and safety. The cane signals’ shapes appear to be the same from whatever direction they are viewed, removing confusion about the message they convey. The same shapes continue to be used today for the sets of Day Shapes used as marine navigational signals that are mandatory on certain-sized vessels.Distant Signal Cone, part of a Flagstaff signal set. A woven cane cone, painted black, with a metal rod passing through the centre and two crossed metal bars at the base. The central rod has a loop at the top and passes through the bars at the base, finishing in a metal loop. The rod has swivels at each end.flagstaff hill, warrnambool, flagstaff hill maritime museum and village, shipwreck coast, marine navigation, marine communications, communication signal, lifesaving, ship at sea, day shape, masthead signal, day signal, day mark signals, marine technology, safety equipment, navigation equipment, marine day shape, day marker, cane day shape, signal cone, day signal cone, cone signal, cone day shape, distant signal, flagstaff signal, signal station, communications, signals, marine signals, flaghoists, international marine conference, international code of signals, signal codes, marine safety, signal flags, daymark, day symbol, navigation, warrnambool flagstaff, 1854, 1857 1931, 1887, 1897

This three-dimensional Distant Signal is part of a Flagstaff Signal set of ball, cone and drum shapes. It has been woven and then fabricated with strong metal swivel fittings and loops for suspending from a high point on a flagstaff at a signal station or on a ship’s masthead. The cane signal was constructed to withstand all weather and to be visible from a long distance. The gaps between the woven cane allow air to pass through, minimising possible swaying. Similar sets were made from rope or fabric. Warrnambool's Flagstaff was erected in 1854. Its primary use was to display visual signals that could convey messages between land and sea. It was also used to notify the local population of the approach of ships. One of the popular signalling codes in use in the early-to-mid 1800s was the Marryat’s Code but there were others in use as well; there was no one standard code. In 1857 the International Marine Conference adopted an International Code of Signals as a standard communications system for all vessels that could be understood in many different languages. The Normanby Advertiser reported on June 5th 1857 a query from the Post Master General as to whether the request of the Chief Harbour Master would be carried out, in that Warrnambool would receive a new flagstaff and a set of Marryatt’s signal flags. The Table of Codes was published, showing how to use combinations of these flags to send messages. The Code was revised in 1887 to cover situations where distance, light, wind and weather conditions affected the visibility of the flags and prevented clear communication. The first report of the International Code of Signals Committee of 1897 warned signalmen not to rely on ordinary semaphore flags and introduced a Distant Signal Code using either particular semaphore flags or the three-dimensional shapes of a ball, cone and drum that aligned with the semaphore flag shapes of a circle, pennant and square. International Code of Signals In 1931, after World War I’s experiences in using signal codes, the International Code of Signals conference in Washington revised and published the rules for the conduct of signalling. One of the changes was that “the use of the Distant Signals and of fixed semaphore was abandoned”. It is of interest to know that modern marine law in many countries insists that a set of Day Shapes must be carried onboard vessels of a certain size. These highly visible geometric shapes are used at sea in daylight to communicate messages between vessels. They are used in a similar way to the Distant Signals, in that different combinations of shapes represent different messages. The set of shapes includes a ball, cylinder, cone and diamond. The shapes are hung between the top of the vessel’s foremast and the front of the vessel. They are only coloured black and are about 1.5 metres high. The vertical line of shapes can mean messages such as Boat not under command, Fishing, and Under sail and power.Distant Signals were an important means of marine communication from the late 1880s to the early 1930s, including during World War I. They were an advancement to the International Shipping Codes and safety. The cane signals’ shapes appear to be the same from whatever direction they are viewed, removing confusion about the message they convey. The same shapes continue to be used today for the sets of Day Shapes used as marine navigational signals that are mandatory on certain-sized vessels.Distant Signal Ball, part of a Flagstaff signal set. A round woven cane ball, painted black, with a metal rod passing through the centre. The rod has a loop at each end, then a concave, octagonal metal plate that rests on the outside surface of the ball, serving as a washer. The rod has swivels at each end.distant signal, flagstaff signal, signal station, masthead signal, communications, marine technology, signals, marine signals, flaghoists, international marine conference, international code of signals, signal codes, marine safety, signal flags, day shape, daymark, day symbol, navigation, warrnambool flagstaff, 1854, 1857 1931, 1887, 1897