Construction on the Sydney Melbourne coaxial cable began in 1960 and was one of Australia's biggest and most important telecommunications projects of the 20th century. The laying of a coaxial cable between Sydney, Canberra and Melbourne, allowed people to direct dial long distance phone calls (rather than operator assisted), and supported simultaneous television broadcasts for the first time. It was officially opened on 9 April 1962 by the then Prime Minister, Sir Robert Menzies. This souvenir coaxial cable was presented to Mr Roy Kerr on his retirement. Mr Kerr was the Assistant Chief Engineer, Headquarters Customer Networks Branch, Telecom Australia.This cable has strong historic significance as part of the historic and technologically important Sydney-Melbourne coaxial cable. The cable represents not only a feat of technology but a shift in social engagement with telecommunication technologies, as it allowed people to direct dial long distance phone calls (rather than operator assisted), and supported simultaneous television broadcasts for the first time; it put the power of connection directly into the hands of the Australian public. This souvenir length of cable is well provenanced, and the details of the cables use and significance is inscribed on the steel casing. A 6 tube copper coaxial cable with lead sheath, quad 20lbs conductor cable (paper insulated), and a presentation metal collar and base. Inscriptions around the top of the metal collar and the base. "OLYMPIC CABLES PTY. LTD / AUSTRALIA" "6 TUBE COAXIAL CABLE / WITH 32 PAIRS 20LBS/MILE UNARMOURED / SYDNEY MELBOURNE 1960"coaxial cable, cable, sydney-melbourne coaxial cable, telstra, postmaster general's department (pmg), telecommunications, subscriber trunk dialling (std), television, telephone

Standard Telephones and Cables Ltd (later STC) was a British manufacturer of telephone, telegraph, radio, telecommunications, and related equipment. The company was based in the United Kingdom but also had an operation in Australia, which was acquired by Alcatel Australia in 1987STC Electric Iron with original pacakging and Warranty.Box: Product of Standard Telegraph and Cables Pty Ltd. 252-274 Botany Road, Alexandra, Sydney, NSW.iron (electric), stc, standard telephones and cables ltd

Yields information about power supply in cables in Ballarat and heating effects.Carbon copy of a typed note or chart giving information about the “Maximum Permissible currents for 6kV and 415V – armoured cables laid direct in ground. Dated 21/7/1942, with initials W.M in top left hand corner. BTPS Number "220" Has “220” in biro in bottom right hand corner and “T/1” in red pencil in top left hand corner.secv, cables, power supply, electricity supply

Henry Sutton is a talented world-wide accepted inventor with inventions relating to the telephone, photography, wireless, cars, motorcycles, and bicycles as well as many more inventions. Henry was also one of four brothers that ran the Sutton's Music Store after the death of their Father Richard Sutton. Henry Sutton taught Applied Electricity at the Ballarat School of Mines in 1883 to 1886.cables, ballarat fire brigade, telephone

The State Electricity Commission of Victoria constructed the Kiewa Hydro Electric scheme from the 1930's to 1960's during which time power cables were made to carry power from the Power stations to the switch yards and beyond to the towns and houses.These sample power cables indicate the types of power lines used in the Kiewa Hydro Electric Scheme and the amount of voltage that they carry.3 transmission cables of different width used for transmitting different amounts of power on different size power lines.The thinnest cable consists of a centre piece of wire covered by a layer of twisted wires. The middle sized cable has 4 layers of twisted wires around the centre piece and the thickest cable has 5 layers of twisted wires around the centre piece.The thickest cable has a plastic strip with 330.000 Volt Cable inscribed on it.state electricity commission of victoria. power lines. cables. kiewa hydro electric scheme. electricity.

.1 - Book - 8 pages + grey covers, side stapled, issued by the Australian Standards Association, "Electrical Voltages and electrical frequencies for new installations ", C1 (a&b) - 1926, December 1926. .2 - Book - 36 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Overhead Line wire material for telegraph and telephone purposes", C3-11-1925, November 1925. .3 - Book - 20 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Telephone cable, paper insulated lead covered", C12 - 1928, January 1928. .4 - Book - 24 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Marking for Switchboard bus-bars and connections" C13 - 1925, December 1925 - with a pasted green label noting that the "tentative standard is now endorsed as Australian Standard without amendment" - dated Oct. 1930. .5 - Book - 32 pages + grey covers, side stapled, issued by the Australian Standards Association, Tentative Australian Standard "Dimensions and Resistances of Bare Annealed Copper Wire for Electrical Machinery and Apparatus", C 18-1926, October 1926. .6 - Book - 12 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard "Slate Slabs for Electrical Purposes", C19 - 1926, July 1926. .7 - Book - 16 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Moulded Flat Top Insulation Bushes" C20-1926, October 1926. .8 - Book - 16 pages + brown covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Australian Standard "Insulation dimensions and resistance of enamelled plain copper wire for instruments and apparatus" C21-1928, January 1928. .9 Book - 20 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Watertight Glands for electric cables" C22-1926, September 1926. .10 - Book - 20 pages + grey covers, side stapled, issued by the Australian Commonwealth Engineering Standards Association, Tentative Australian Standard - "Air-break knife switches and laminated brush switches for voltages not exceeding 660Volts" - C23 - 1926, August 1926" On top right hand corner has the date stamp of the "The Electric Supply Co. of Victoria Ltd Ballarat" trams, tramways, power station, standards, materials, electrical systems

Standard Telephones and Cables Pty Ltd was a telecommunications company that began as part of Western Electric, a telephone manufacturing company set up by Alexander Graham Bell. Following the First World War, Western Electric diversified to include electric generators and wireless receivers, all still imported. In 1925, Western Electric was sold to the International Telephone and Telegraph Company. In Australia, it became known as Standard Telephones and Cables (Australasia) They worked closely the Postmaster Generals department to set up telephone and radio networks throughout Australia. Its first factory was in Chippendale, New South Wales but ut developed to have branches in all stated of Australia. By the end of the Second World War STC was Australia's biggest manufacturer due to its critical role in producing telecommunications equipment, domestic radio receivers, telecom cables, military equipment and electron tubes. The company returned to peacetime manufacture. Rather than reduce staff it used its excess capacity to produce electric irons and other domestic appliances including vacuum cleaners and floor polishers. This model was produced at the beginning of the 1950s. It was once owned by Mr. Stiff from Stiff and Gannon, Wodonga.This item has local and national significance. It was used in a local Wodonga business and is representative of domestic appliances used in the 1950s. It also has national significance as it is an excellent example of good produced by the manufacturing industry in Australia during that period.Model 30 Airzone Vacuum Cleaner and accessories. Manufactured in AustraliaMetal logo for Airzone including engine specificationsdomestic appliances, standard telephones and cables pty ltd

Fiels telephone used in WW2.Military field telephone, with handsetMounted on front of the telephone is an identification plate with the inscriptions “REPLACE HANDSET WHEN FINISHED AND RING OFF. TELEPHONE SET “F” MK 1. STANDARD TELEPHONES AND CABLES PTY LTD SYDNEY 1943. D ^ D. Also mounted to the front of the phone is a smaller plate with inscription “ Serial No. 5971. telephone.

This probably was used with single telephone cable earth return in WW1.This is a circular metal cable drum. The centre 'axle' is made a cylindrical piece of timber. It in turn, has a square metal bearing. This square metal bearing has a square hole in the centre 15 x 15 mm. This is held in place with 4 slotted screws. There is a small length of rubber covered cable exiting from one side of the drum. It is a 5 core cable. In the wooden drum is a metal sleeve. It can be slid around to reveal a metal screw terminal.On the side that has the cable exit can be seen, "HEARL & HEATON & SONS LTD 11 1918" ww1, cable drum

Photo shows the horse drawn MMTB cable drum carrying wagon at the TMSV Museum at Bylands, mid 1970s. Has the MMTB identification, address and mass details painted on the vehicle. Behind the wagon is a Furphy water cart. Used to carry and distribute cable including overhead. Photo of the vehicle can be seen on page 68 of the book Destination City 3rd Edition.Yields information about the MMTB cable drum carrying wagon at Bylands.Photograph - MMTB horse drawn cable drum wagon at the TMSV Bylands Museum On rear in ink. TMSV – Horse drawn cable drum wagon at Bylands (Also Furphy water tank), Keith Kings photo. tramways, tmsv, bylands, horse drawn vehicles, overhead, cable drum

Photograph of trailer 532 west bound in Johnston St Collingwood about to pass under the railway bridge, with a Tait set on the top and another cable tram set eastbound. The bridge has an advert for Laconia Blankets and R. L. Scott Chemist. Photographer - possibly Wal Larsen based on negative size and Reg Item 5064 and on the last day of service 14/4/1939.Yields information about the Johnston St cable trams.Negative of cable trams, print also held.Written on rear of album print "Collingwood cable trams passing under railway bridge at Victoria Park"trams, tramways, cable trams, johnston st, collingwood, railway, bridges, tram 532

1 - employee with a uniform cap - could be a shunter - lifting the cable into the adjacent grip car. Marked on rear as "Lonsdale St" .2 - worker in a cable pulley maintenance pit oiling the mechanism - note the other pits. Has put a "Danger" sing out on the roadway. Marked on rear "Bourke and Spring St 1938" Two copies held and one digital image from a scene shot. .3 - a worker watching the cable entering a winding house looking for damage - what a boring job! Marked on rear as "Checking cables 1938" .4 - communications pillar - or box - to communicate with the winding house .5 - photos shows the grip in the roadway Images have been reproduced from a movie - Commuting by Cable?Yields information of the cable tram operations c1938.Series of five Black & White Photographs by the TMSV Sales and one digital image from Commuting by Cable. Has the TMSV Sales stamp on rear with some notes in pencil on the rear as shown above.trams, tramways, cable trams, grip tram, cables, winding house

11 slides demonstrating cabling in trees Aug?. I of a tree.Labelled "Cabling"tree cabling, demonstration, arboriculture, students

Blueprint of drawing No. R3232, titled "MTOC - Sheaves and Pins" providing a drawing of each type of cable car sheaves, pins and washers, includes title, dimensions and weight of each piece for use on the Melbourne cable tram system. See also Reg Item 353 for a book of these drawings. Drawing dated 23/6/1897, has been given a MMTB drawing number.On rear of drawing in red felt pen, "Cable car pins and parts" and in black ink "R3232"trams, tramways, mmtb, mto co, cable trams, cables, winding houses

Field telephone set D MK V - used for sending messages in the field via voice. Serial No. 21396.Rectangular metal box with hinged lid, containing communication apparatus for sending verbal messages. Attachments on sides & rear for carrying straps. Hook & eye latch on front for securing lid.Instruction plates on inside of hinged lid. “Serial No 21396”communications - telephonic, military equipment - army, metalcraft, passchendaele barracks trust

Black KM2 bakelite military field use telephone with attached hand-receiver and spiral cord in battery charger.Three plaques, battery instructions, model and serial number, mod.record, off ring and buzz settings, at back: L1, L2, CBS, MAG, CBtelephone, communication, field telephone

An example of a Telephone Set D Mk V which was used by Australian forces during the Second World War for verbal and Morse code communications over short distances via a telephone line.An example of a Telephone Set D Mk V which was used by Australian forces during the Second World War for verbal and Morse code communications over short distances via a telephone line. Rectangular aluminum green painted box with broad canvas webbing strap secured to the side of the body through metal loops. Two vertical webbing loops are attached to the rear of the body. Stencilled in black on top TELE. SET. D. MK. V.'. The housing opens by a hinged fold back lid that is secured by a hook and eye closure. Attached to the inside of the lid are two metal plates. The first is a circuitry diagram, the second is the instructions for use of the set. The interior contains the phone assembly and is divided by a metal shelf. On the left is a bell with two screw terminal in front. At the center is the telegraph key and behind that is the battery box with a small metal plate with, 'TELEPHONE SET. D.MK.V To the right is metal box with two terminals in frontAttached to the bottom of the shelf is a slide out metal key Below the shelf is a compartment in which is stowed a black metal headset with provision for a bakelite handset with attached cord and four-prong plug.Tele Set stamped on outside of unit. Inside lid plaque - Telephone Set D MK V

1. Metal cased field phone. it has a bell, 2 line terminals, a battery compartment, a morse key and a 2 knob buzzer assembly. Coming out from inside is a Bakelite earpiece. On a lead on the lid a field modification has been made to support the handset (2) externally. I rear holding strap is missing. 2. Black Bakelite hand piece, press to talk switch and a heavy duty 4 pin plug.Stamped inside is 1668. Inside the lid is an operation chart - in brass. Stamped serial 25969.ww2, signals, telephones

Photograph shows the device used to send a "telegraph" signal to the winding or engine house. They were positioned along the track and enabled the tram crew or a cable tram worker to send a signal about the cable. The crew member would set the pointer and depress the trigger. This sent the signal which was recorded on a telegraph tape, indicating the signal and the location of an incident. Installed by the Melbourne Tramway and Omnibus Co. (MTOCo) This photograph is Public Records Office photo H165, 166 and 167 in the Victorian Railways collection.Yields information about the type of equipment the MTOCo used to operate the cable tram system.Set of three Photographs - Black and White of a Melbourne cable tram signalling device.trams, tramways, cable trams, mtoco, signalling, cables, engine houses

Section of worn cable tram wire rope. One of the two ferrules has been engraved with "243 Weeks 341591 Miles" and the other "ANTD 12 Weeks" - "ANTD" is thought to be an abbreviation for anticipated. On this basis, the cable rope lasted 20 times its expected life! Demonstrates a worn cable tram wire rope that has been sampled and its use recorded.Section of worn Melbourne cable tram wire rope with engraved retaining brass ferrules on each end consisting of seven wound (12 wires) around a central fibre core.See contexttramways, cable trams, cable ropes, cables, mmtb

This photograph shows crowded cable dummy at night with "Northcote' destination and "The Aquarium Exhibition Building' sign on the side of roof.Yields information about closure of cable tram network. Black and white photograph with pencil note on rear. 2730 last cable tram to run on Bourke St cable routetram, cable tram, last tram, bourke st cable tram

Photograph - black and white of a drawing by Jack Stranger showing the tunnel and pit layout at Nicholson and Gertrude Streets corner, Fitzroy for the cable tram engine house. Includes the supplementary cable and the layouts of the various sheaves. See notes below for origin of the photograph.In ink on the rear: "Melbourne - "Drawing by Jack Stranger showing the tunnel and pit layout at Nicholson and Gertrude Sts corner, Fitzroy for the cable tram engine house. Compiled by exploration during March and April 1955? at the start of the Bourke St Tramway conversion. Photograph while on display at the TMSV exhibition at Stanhope St Malvern Tramway Hall 10/3/73" KSK print number 122-26.trams, tramways, cable trams, gertrude st, winding houses, cables