This is a typical example of a flat wick domestic paraffin lamp used in households prior to the introduction of electricity.A flat-wick lamp is a simple type of paraffin lamp, which burns paraffin drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce. The wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the wick. This has a cooling effect and keeps the wick from over heating. The lamp burner has a flat wick, made of cotton. The lower part of the wick dips into the fount and absorbs the paraffin; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the paraffin that the wick has absorbed burns and produces a clear, bright, yellow flame. As the paraffin burns, capillary action in the wick draws more kerosene up from the fuel tank. All paraffin flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above. (Source: Wikipedia accessed 24 Nov 2023) This lantern has a circular heavy green glass base for holding the paraffin. The base has a 12mm green glass handle. There is a small clear glass chimney with a fluted upper edge and some bubbles in the glass. The metal burner and wick holder has four metal prongs to hold the glass chimney in place. The round metal wick winder is functioning. There is a small amount of residual paraffin in the base. The flat wick is made of cotton.There are no markings to indicate the manufacturer.paraffin lamp, flat wick lamp, domestic lantern

Kempthorne Lighting Pty. was established as Coffey Lanterns in East Malvern, Melbourne Victoria in 1931 by brothers Selwyn and Owen Coffey. They manufactured lighting fixtures and fittings including oil lamps for marine use as well as for the domestic market. In early 1936 two other brothers, Erle and Terence had joined the company which was renamed Kempthorne Lantern Works Pty., Ltd. In 1946 Kempthorne joined with a small design team who had developed a domestic fan to form the subsidiary, Mistral fans. The company previously known as Kempthorne Holding Ltd was listed on the stock exchange in 1968. In 1977-1979 Kempthorne Mistral Ltd. Was a holding company comprising of Kempthorne Lighting Pty., Ltd. & Mistral Fans Pty., Ltd. An early Australian made marine lamp by a significant manufacturer that is still in business today making electrical equipment. The item is an important artefact that was made by an early Australian business that started in the 1930s. Over the years this company has demonstrated many innovations to the manufacturer of electrical items. Marine copper Lamp, round with brass makers lozenge and rounded hollow lugs set on either side of the lamp. Heavy metal handle with brass locking pin. Lid with catch on top. Made by Kempthorne Pty Ltd Melb. 1941flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, copper ship lamp, ship lamp, kempthorne pty ltd

Carl Hermann Nier in 1877 a silverware maker started to produce miners lamps and household lanterns in Beierfeld, Saxonia, East Germany. In January 1902 he established the Nier-Feuerh and company in his home town to produce kerosene lanterns. Carl's three sons Bruno, Curt and Woldemar Nier made the company into the largest lantern producer in the 1930s with Bruno Nier holding many patents for lamps. Lantern production was interrupted by World War II and ceased at the end of 1944 because of the shortage of materials and the advancing Russian army. After the Second World War the company restart the lantern production in 1947 at Luedenscheid and Hohenlockstedt north of Hamburg and fully re-establishing the company in 1950. A domestic item with an interesting history that now is sought after by collectors giving an insight into how hurricane kerosene lamps came into being from a manufacturer in Germany that held numerous patents for oil lamps from 1902 until 1940.Kerosene Lamp with handle, blue in colour, badly rusted. Lamp shade has lever to lift so you can light. Marked "Feuerhand Nr 327" "Made in Germany".flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, kerosene lamp, hurricane lamp, nier-feuerh, carl hermann nier

Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. Late in the 19thC designers experimented with heat retaining fillings for these irons. William Coleman began selling Kerosene lanterns in 1900 in Kingfisher, Oklahoma, USA. He moved to Wichita, Kansas in 1902 and the company became world wide. The company also produced a range of cooking stoves and domestic irons. This spirit- fuelled flat iron was very popular in 1920s - 30s These sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire The family of Miss M Curtis were early settlers in Moorabbin ShireA) spirit- fuelled, sad iron with chrome plated sole c1920, and metal trivet The iron is blue enamel with a white speckled body, with a hemispherical tank for the Coleman 'Lighting Petrol' that provided the heat for smoothing the material B) Coleman Fuel measuring can and funnellMetal Trivet/stand " COLEMAN" ; Petrol can " COLEMAN" / MEASURING CAN / for INSTANT LIGHTING IRON/ with printed instructionssad iron, kitchen equipment, coleman william, kansas, oklahoma, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh, fireplaces, stoves, petrol fuelled irons, spirit flat irons, coleman lamp stove co. ltd.

Glass lantern chimney with no holes. It is a tube shape with two protruding ridges around the circumference of the chimney at the middle. light, fuel, lamp, domestic item

This lantern was made by Thomas Ward in 1884 for his daughter Alice Fawthrop Ward to see her way to the little church Wellington Road, where she played the organ for the mid week service. An early example of lighting used in the late 1800s. Additionally this particular light was made by Thomas Ward who was a part of a prominent family in Portland at the time. Thomas was part of the crew that went out to the Admella Shipwreck. The above mentioned church was built in 1870, and is now part of a private residence. Metal lantern painted cream. Round base with 6 rectangle shaped glass panels with 2 curved reinforced metal braces rounding the circumference of the body. One of the panels is a functioning door to allow candle access, door is secured by a thin pin with a ring pull to slide pin up and down. Top is domed with a decorative waves cap. Thin metal carry handle attached by two side braces. Cylinder holder in the base for a candle, and contains a small new looking candle.Hand written label: This lantern was made by Thomas Ward in 1884 for his daughter Alice Fawthrop Ward to see her way to the little church Wellington Road, where she played the organ for the mid week service.thomas ward, city of portland, lantern, alice ward, church, admella shipwreck, portland lifeboat

Sherwood Ltd. Was a manufacturer of oil lamps and burners at the Nechells Park Works Birmingham UK and regarded at the time as a renowned name in the oil lamp and burner manufacturing industries in Birmingham during the early part of the 20th century. They started selling as ‘Isaac Sherwood & Son Ltd.’ in 1904, later around 1920 they merged with Linley and Co makers of American pattern lamps and became ‘Sherwood-Linley” moving to 44-50, Granville St. Birmingham. They became one of the largest manufacturers of lighting devices and burners in England. They produced all sorts of illumination devices and became famous for their oil burners. Apart from oil burners, they produced table and floor lamps, sconces, lanterns and chandeliers that made Sherwood unique. A Significant item as part of a kerosene lamp that was commonplace in homes and other premises during the early 20th century as a means of lighting before electric lighting became the standard. These types of items give a snapshot into domestic and social life during this period.Lamp Burner housing, brass with wick-screw (no wick). Made in England Sherwoods LTD Birminghamwarrnambool, flagstaff-hill, shipwreck-coast, flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp burner, sconces, kerosene lamp, wick adjuster, sherwood & son ltd, sherwood-linley

This item is an example of a lighting device commonly used before electricity was widely available for domestic use.A hurricane lamp with a rounded tank and small carry handle (a larger handle is possibly missing). It has a lever to open the glass tank. It has a metal base which is filled with kerosene. On top is a metal hood with vents.Around base : Chinese characters. On top : "Made in China KWANG HWA"lighting lantern kerosene-lamp hurricane -lamp

This lantern could have been used for railway lighting. Railway lighting illuminated not only stations but also yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. This is a hand-held light.Railway lamps of this kind were significant railway items in their period of use as essential tools to the safe-working operations of the railway. Used domestically these lanterns were common in the period before the widespread connection of electricity. A painted red metal "hurricane" lamp which has a glass shade. This is a portable oil lantern which has an oil tank on the bottom that forms the base of the lamp. The tank has a door for filling and it also houses the wick and knob that increases or decreases the length of the wick.On base : No. 707 Globe Brand (globe of world) World Light MFY LTDlantern lighting hurricane-lamp

Carl Hermann Nier in 1877 a silverware maker started to produce miners lamps and household lanterns in Beierfeld, Saxonia, East Germany. In January 1902 he established the Nier-Feuerh and company in his home town to produce kerosene lanterns. Carl's three sons Bruno, Curt and Woldemar Nier made the company into the largest lantern producer in the 1930s with Bruno Nier holding many patents for lamps. Lantern production was interrupted by World War II and ceased at the end of 1944 because of the shortage of materials and the advancing Russian army. After the Second World War the company restart the lantern production in 1947 at Luedenscheid and Hohenlockstedt north of Hamburg and fully re-establishing the company in 1950. A domestic item with an interesting history that now is sought after by collectors giving an insight into how hurricane kerosene lamps came into being from a manufacturer in Germany that held numerous patents for oil lamps from 1902 until 1940.Kerosene lamp with handle, red in colour, badly rusted. Lamp shade has lever to lift so you can light it.Marked "Feuerhand Nr 327" "Made in Germany".flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, kerosene lamp, hurricane lamp, nier-feuerh, carl hermann nier

This smoking set was brought home by a member of BCOF, Japan. C.H. Shearing NX206537. Refer Cat No. 7089.16P for his service details.Six piece set of chromed pewter. 1. Tray, small, handles each end. Flower pattern tapped in to it or part of the mould. The flowers are of a five petal variety. Two corners have been bent back and damaged. 2. Base, ash tray. Rectangular shape with curved floor. There are some scratches and the coating is peeling. 3. Top of ash tray. Flower motifs, two channels to rest cigarettes. Pagoda on the side and bridge at bottom. 4. Match box holder, 4 sided, 2 sides raised a bit higher than the end. Rectangular base, flower motif. Some copper colour substrate shining through. 5. Base holder for packet of cigarettes. Rectangular shape with small lip around rim. The outside bottom surface has a lumpy appearance. The inside is well worn with scratches and marks. 6. Lid, cigarette packet holder. Flower motif top LH corner. A building with a wide roof in center. Two windows and a door in centre. Steps and fence under that. Bottom left has what looks like a bird home. R.H. Side possibly a lantern. Bottom right side has the word "NIKKO" embossed on it. Top is a bit worn, copper substrate coming through. There is a green tint showing on the roof of the building.smoking set, ww2, bcof, japan, c.h. shearine

The period when kerosene was extensively used for indoor lighting was before electrical reticulation was installed in rural areas. In remote areas this was up to the mid 1900's. The kerosene lantern however was still in use, for camping and outdoor activities, well beyond this period and was eventually replaced by LPG and battery powered lighting. The transition phase to "modern" outdoor and domestic lighting lingered on the rural areas where the electrical reticulation suffered from reliable constant supply.In the Kiewa Valley, being a rural region, had reliable electrical domestic and farm supply only after the Kiewa Hydro Electricity Scheme had been fully operational. The supply was relative to how close the homestead was to the major electricity substation. This kerosene lamp was in use during the period when it was the only reliable source of domestic night time lighting. The strength of refractive light produced by this lantern/lamp hinged upon the size of the lamp(wick and glass bowl). The small size of this lamp suggests that it was for use in a small room(children's bedroom) or as providing a light for a safe walk to the outside ablutions (toilet) area. This small kerosene lamp has an enclosed "cup" body which would have contained the kerosene fuel. The top wick holder, made from brass, has an extended enclosed spout which raises the wick approximately 20mm from the bottom of the holder. The wick holder screws into the the top of the kerosene reservoir bowl and has a wick adjustment screw (light control) at one side. The small white glass light reflector bulb nestles securely onto the wick holder and is kept snug by snap designed extending "fingers". The section between the bottom of the refractive glass "light" bowl and the top of the kerosene bowl has perforations to allow air passage to feed directly to the wick.The light refracting bulb is open at the top to allow heat and smoke from the burning wick to escape upwards.On the wick control screw "CWB BRITISH MADE"kerosene reading lamp, domestic lighting, bedside light

Object. Kaleidoscopic magic lantern slide cased in a brass disc, and a cracked wooden case - metal turning crank handle is missing.photography, projectors - still

Small antique wood and glass Kaleidoscope with turning rod.photography, projectors - still

Object. Small antique wood and glass Kaleidoscope with turning handle.photography, projectors - still

This portable lamp was manufactured by the Lucas Industries, a company in Birmingham, England that first produced lamps after 1875. It could have domestic use or be attached to cars or bicycles early in the 20th Century to provide light at night. The lighting fluid was oil. This object is an interesting example of lighting for cars and bicycles and in the home in the late 19th and early 20th Centuries.This is a brass lantern with a circular glass piece in the middle front, and a top metal mechanism with a handle. Inside the circular opening is a domed jet with holes for lighting the lamp. On the sides there are various mechanisms for turning the light up and down, opening the front glass and opening the bottom to allow filling of the lighting fluid. The item is corroded on the exterior. The top has air vents to permit the vapours to escape. On the side is the maker's name LUCAS No. 722 KING OF THE ROAD JOS. LUCAS LTD. vintage lighting, lucas industries

Rectangular paper stamp with a dark blue background and white graphics and print. Graphic consists of a lantern. with beams of light extending outwards. Marked: On front: "PRICE THREEPENCE / ASSOCIATION FOR THE ADVANCEMENT OF THE BLIND / Homes & Help.Rectangular postage stamp with white lantern streaming light against blue backgroundAssociation for the Advancement of the Blind Homes & Help Send donations to 10 Queen St Melbourne C1association for the advancement of the blind, fundraising

1. State Express Ready Rubbed, produced by the Ardath Tobacco Company (est. 1895 London), was a popular Virginia tobacco, notably manufactured in Australia during the mid-20th century. The tins were typically small to mid-sized, featuring the "State Express" and "Ardath Fine Cut" branding, with "Ready Rubbed" indicating it was pre-shredded tobacco. Used widely by Australian soldiers in WWII, these compact tins are highly collectible today, appearing through the 1960s. 2. The Tilley Storm Lantern,company started in the early 19th century, with William Henry Tilley manufacturing gas lamps in the 1830s. By 1919, the company pivoted to kerosene (paraffin) pressure lamps, using a pressurized system for lighting, which was improved with incandescent mantles. The company expanded rapidly, securing major contracts to supply lamps to railway companies for track work and inspections. Tilley lamps were extensively used by British armed forces during both World Wars. In WWII, they were essential for field operations, guiding aircraft (RAF), and providing light in blackout conditions. 1. A red rectangular, State Express cigarette tin with a hinged lid. The company logo and other details are printed in gold lettering on the lid as well as Ready Rubbed Virginia Tobacco Ardath Fine Cut. There is an insignia with two crossed heraldic flags and an eagle on top. This information is printed in black lettering on a gold background inside the lid. 2. The tin contains a folded green paper instruction leaflet for the use of a Tilley Storm Lantern made in England with a black plastic branded Tilley Spare Part Dipstick used for measuring the fuel level. There is also a broken thin black ring fitting.1. On the front of the lid: 'State Express Ready Rubbed Absolutely unique in its quality Virginia Tobacco Ardath Fine Cut'. There is an insignia with two crossed heraldic flags and an eagle on top. 2oz. Net Weight. When packed is at the bottom in black print. Inside the lid: 'Every tin of genuine Star Express Ready Rubbed Ardath Fine Cut has the name of Ardath printed on the paper lining' The insignia is also printed. 2. Included is a green folded pamphlet 'Hints on the use of your Tilley Storm Lantern (Regd.)' Information in the leaflet is quite detailed. The dipstick has 'The Tilley Lamp Co. Ltd. Dipstick for Models named on reverse. E.X.100.,P.L.53.,10.,T.L.13., R. T.L.106.,T.L.136.,X246.K.L.80.,LIFE BUOY. USE ONLY GENUINE 'TILLEY' SPARE PARTS'smoking equipment, cigarette containers, tobacco

Tilley lamps, famously known for their bright white light and reliance on kerosene pressure, originated from John Tilley’s 1813 invention of the hydro-pneumatic blowpipe. Developed as a portable paraffin (kerosene) lamp in 1915, the Tilley Lamp Company became iconic for durable lighting in the railways, military, and households before moving to Northern Ireland in the 1960s. They were used in homes and outdoors.Four vintage Tilley Lamp Vapourisers ( three new and one sealed in a plastic wrap). 1. Tilley Vapouriser Part No. 606. in a red and yellow long rectangular cardboard box complete with a cleaning wire part. 2.Tilley Vapouriser Part No.No. 606. in a red, black and white long rectangular cardboard box, complete with a cleaning wire part. 3. Tilley Vapouriser Part No.169. in a black and yellow long rectangular cardboard box, complete with a cleaning wire part. They all have patent numbers. 4. One loose vapouriser encased in plastic without a box.Each box has full details of parts and manufacturing.lighting equipment, lights, lamps, kerosene lamps

Wall-mounted kerosene lanterns revolutionized home lighting in the mid-19th century, following Ignacy Łukasiewicz’s 1853 invention of the modern kerosene lamp. They provided a bright, safe alternative to whale oil, using glass chimneys and metal reflectors (often on wall brackets) to illuminate rooms and railway guard’s vans until rural electrification in the 1940s. A vintage cream coloured tin wall mounted kerosene lamp for use to light the home in the 1900's. It has a shaped back support with a mounted circular reflector attached to a slide in slot. At the front there is a kerosene container with an adjustable turning wick. A glass chimney would have covered the wick to stop the flame from blowing out. There are four metal clips to support the chimney.lamps, lighting equipment, argand lamps, kerosene lamps, wall lamps

Wall-mounted kerosene lanterns revolutionized home lighting in the mid-19th century, following Ignacy Łukasiewicz’s 1853 invention of the modern kerosene lamp. They provided a bright, safe alternative to whale oil, using glass chimneys and metal reflectors (often on wall brackets) to illuminate rooms and railway guard’s vans until rural electrification in the 1940s. A vintage tin wall mounted kerosene lamp for use to light the home in the 1900's. It has a shaped back support without a mounted circular reflector. At the front there is a kerosene container with an adjustable turning wick. A glass chimney would have covered the wick to stop the flame from blowing out. There are four metal clips to support the chimney.lamps, lighting equipment, argand lamps, kerosene lamps, wall lamps

The cabinet has a curved back and would have been custom‐built to fit the dimensions of the lantern room interior. It is likely to date from when the lighthouse was built in 1884 and may have been among the items delivered by the government steamer dispatch early in March which included ‘the lantern and other fittings for the Cape Nelson Lighthouse’. The Public Works Department provided a range of lightstation furnishings including office desks and cabinets, and domestic settings for keepers’ quarters, with nineteenth century items often stamped with a crown motif and the PWD monogram however the curved cupboards installed in Victoria’s lighthouse lantern rooms do not appear to display this small feature. Further research may reveal more about their manufacture and it is tempting to think that they were perhaps even supplied by Chance Bros as part of the entire lantern room installation. The company usually provided the timber battens for the lantern room paneling, and a cabinet may have been included in the assemblage. Another possibility is that the specially designed cabinet was made on site by carpenters along with other fittings. It is not known whether it is attached to the wall or movable; if attached it is considered to be a fixture and included in the Victorian Heritage Register listing for the lightstation (VHR H1773). Its location, when identified in the CMP of April 1995, was on the ‘lower lantern level’, where there was also a ‘timber step ladder’ (Argus, 6 March 1884, p6. nineteenth or early twentieth century), ‘timber framed lighthouse specification’, ‘timber framed chart’ and telephone .Residue on the furnishing indicates that it was formerly painted green, the colour of some of the other fixtures in the room, such as the original cast iron ladder. It is now partially varnished and the corner to the top’s edging on the right side has been cut off. The lighthouse also has a large curved back, two‐door cupboard. Other similar cabinets with curved backs survive at Cape Schanck, varnished wood cabinet with brass door knob, no drawers; Point Hicks, painted green with silver doors, no drawers and Gabo Island, bench top, 2‐door, no drawers, green paint removed to reveal cedar timber). Cape Nelson’s curved cabinet is unique among these examples for having drawers. The cabinet is a unique, original feature of the lantern room and has first level contributory significance for its historic values and provenance.The bench top cupboard has two drawers, each above a door, and each door is framed and beveled around a central panel. The cabinet has a curved back.

The two-door nineteenth century cabinet was purpose built with a curved back to fit the proportions of the lantern room interior and is likely to date from 1888-89 when the new lighthouse was fitted out and provided with furnishings and fixtures. The Public Works Department provided a range of lightstation furnishings including office desks and cabinets, and domestic settings for keepers’ quarters, with nineteenth century items often stamped with a crown motif and the PWD monogram. The curved cabinets installed in lantern rooms however do not appear to display this small feature. The cabinet needed to be custom made to fit the proportions of the room, and for this reason it was possibly made on site or perhaps even supplied by Chance Bros as part of the entire lantern room installation. The company usually provided timber panelling for their lantern room interiors (since removed from Point Hicks), and a cabinet may have been included in the assemblage. It may not have originally been painted; today doors area grey/silver colour and the rest of the cabinet is emerald green. It is not known whether it is freestanding or fixed to the wall. A similar cabinet with panelled doors remains in the Gabo Island lighthouse and evidence of green paint on the wood indicates that the cabinet frame was also formerly painted green but later stripped to reveal the wood finish. The Cape Nelson lantern room has a curved cabinet with the same door type but has a drawer above each door. It too was formerly painted emerald green before it was stripped back to its present wood finish. Cape Schanck’s lantern room cabinet is unique for its curved front as well as curved back, and it stands on a skirting. The two doors are in the same style, although they open with a brass knob. Further research into these distinctive cabinets may resolve the interesting question of their construction. The Point Hicks cabinet is a unique, original feature of the lighthouse lantern room and has first level contributory significance for its historic values and provenance. The Point Hicks cabinet has two doors, each framed and beaded around a central panel, and there is a simple door knob. The back is curved and the front is straight and the doors are painted a grey/silver colour and the rest of the cabinet is emerald green.

During the Victorian goldrushes of the 1850s thousands of Chinese migrants arrived to seek their fortunes. At that time many came to the lucrative gold fields of Northeast Victoria. After the Gold rush, many Chinese migrants returned home. However, a number settled in the area as merchants, hawkers and market gardeners in surrounding towns including Wodonga, the Ovens, King, Buffalo River and Kiewa Valleys. They also rented lands and established themselves in the hops and tobacco farming industries. Items of Chinese origin made their way into many households. Importation of Chinese mass produced items such as this lantern continued well into the 20th century and were common domestic items across Australia before households were connected to electricity.This item is representation of kerosene / paraffin lamps used throughout Australia to provide lighting inside and outdoors prior to the widespread availability of electricity.A small hurricane lamp with a rounded tank and small carry handle attached to the top. A larger handle is also attached at the top of the frame. It has a lever to open the glass tank. It has a metal base which is filled with kerosene. It has a screw knob to open the kerosene receptacle. The metal hood also has vents. The Chinese characters around the base translate to "Shanghai Guanghuaheng".Around base : Chinese characters. On top : "Made in China KWANG HWA"kerosene lamp, domestic appliances, chinese artefacts

The Wodonga Historical Society Haeusler Collection provides invaluable insight into life in late nineteenth and early twentieth century north east Victoria. The collection comprises manuscripts, personal artefacts used by the Haeusler family on their farm in Wodonga, and a set of glass lantern slide negatives which offer a unique visual snapshot of the domestic and social lives of the Haeusler family and local Wodonga community. The Haeusler family migrated from Prussia (Germany) to South Australia in the 1840s and 1850s, before purchasing 100 acres of Crown Land made available under the Victorian Lands Act 1862 (also known as ‘Duffy’s Land Act’) in 1866 in what is now Wodonga West. The Haeusler family were one of several German families to migrate from South Australia to Wodonga in the 1860s. These rubber pipes were used for enemas, and provide potential for interpretation in the areas of social history and medical history. This item has well documented provenance and a known owner. It forms part of a significant and representative historical collection which reflects the local history of Wodonga. It contributes to our understanding of domestic and family life in early twentieth century Wodonga, as well as providing interpretative capacity for themes including local history, social history, and women’s history. A black box for hard rubber pipe syringes, manufactured by The Global Syringe. On lid of box: "THE GLOBAL SYRINGE/NUMBER FOUR/HARD RUBBER PIPES"syringe, rubber pipes, medical, medicine, medical history, wodonga, haeusler, haeusler collection