Information from Norman F. Dalton: Ballarat had a reticulated DC supply in the early part of last century and in 1905 had sufficient generating capacity to enable the trams to be changed from horse drawn to DC electricity. The use of electricity increased with the main power station located on Wendouree Parade, near Webster Street, under the ownership of The Electric Supply Company of Victoria. AC generating plant was installed in 1925 and conversion to AC proceeded. In 1934 the company was taken over by the State Electricity Commission Victoria (SECV) and more AC generation was installed and the changeover of customers was accelerated. This is around the time that the Synchronome Frequency Checking Mast Clock was installed at the Wendouree Parade Power Station. The SECV Annual Report of 1921 states: ::Section 11 of the act directed the COmmission to enquire into the question of securing the adoption of such standards of plant and equipment of a system, frequency and pressure for the generation and distribution of electricity as will admit of the efficient interconnection of undertakings throughout the State. In 1934 when the SECV took over the Ballarat operations the question of linking with the State grid had been a planned operation for some years but due to financial considerations had hindered it and in fact would continue to do so for a further 10 years. So while the need for close frequency control for interconnection was hardly an issue, the need to keep electric clocks correct was important, particularly as this item was a frequent sales point to cover the inconvenience and sometimes expense of converting from DC to AC. The clock is a very accurate pendulum clock with provision for varying effective length during operation for precise time regulation. There are two normal time dials and one is controlled by the pendulum and the other is operated by the system frequency. When the clock was in use it was installed by the MEter and Tests Laboratory and the time was checked daily by radio time signals. The two dials were repeated in the operators control panel in the Power Station. A maximum deviation between the two dials was set in the operating instructions (eg 5 seconds) and the operator would correct this when necessary by remote manual alteration of the turbine governor set point. The clock was used to drive and regulate a system of "slave" clocks which were used to display the time in various locations around the power station. A slave clock is a simple clock which is driven by a small electric motor, its accuracy is regulated by the master clock every 30 seconds to ensure that it and all the other slave clocks in the station are on exactly the right time; slave clocks were placed in various locations, from common rooms to workshops. A master clock could potentially run thousands of slave clocks at one plant. The clock also contains a rectifier. A rectifier is a device that is used to convert AC power to more stable DC current.Two clocks in a timber case. Both are electric, one is powered by the main pendulum mechanism, the other is a self contained electric clock. The main mechanism is of the gravity arm and roller type, which sends an impulse to the slave clocks every 30 seconds. The This Synchronome Frequency Checking Master Clock was used at the Ballarat Power Station. Below the main section of the case is a smaller cabinet containing a rectifier to provide consistent DC power for the clock. The rectifier was made by the Victorian company Hilco, which was located in Burwood. There is a high chance this is not the original rectifier from this clock as there appears to be brackets to hold a larger device in the space the rectifier occupies.Front below main clock face on front of case: "Patented Sychronome Brisbane" Lower left-hand clock face: "Frequency time" Lower right-hand clock face: "Standard Seconds" Synchronous electric clock mechanism on door (Frequency time clock): >200/250 V. 50~ >"Synchronomains" Made in England >Direction indicator for clock starting switch >"To start move lever in direction of arrow and release" >"Patent applied for" Mechanism for "standard seconds" clock: >"English Made" >"Patented" >Serial number "321" >0 above right-hand pillar on front-plate Mechanism for "standard seconds" clock: >"English Made" >"Patented" >Serial number "321" >0 above right-hand pillar on front-plate Mechanism for main clock face: >"English Made" >"Patented" >Serial number "8751" >0 above right-hand pillar on front-plate Inside case, back panel, top enamel plate: >Seconds Battery + Pos. > Battery Common or - Neg. >1/2 min dials Inside case, back panel, bottom enamel plate: external seconds dial Inside case, right hand side, electrical knobs: two switches, both "A.C. mains" Pendulum rod, below suspension spring: Serial number (?) 0000005 Rectifier in bottom cabinet: >"Hilco Rectifier" >"A.C. Volts 230/240" >"Model 1060/S" >"A.C. Amperes" >"Serial No. 1060/S >"Phases 1" >"D.C. Volts 6" >"C.P.S. 50" >"D.C. Amperes 1" >"Made in Australia by Hilco Transformers McIntyre St., Burwood, Victoria." Bakelite electrical plug: makers mark Lower cabinet, RH side panel, pressed tin plate: "AC" (upside down) Brass speed adjustment, outer right RH side: "S" and "F" Ivory and wood pendulum beat ruler: >Ruler, with 0 in centre and numbers 1-5 in ascending order from centre on left and right. > "Synchronome Patent." Steel plate, back panel, inside case, right hand side: >N R A" (descending) >"2191" serial number/part number Face of main clock: "Synchronome Electric" synchronome frequency checking master clock, electricity, state electricity commission, wendouree parade power station, secv, clock, time, pendulum, electric supply company of victoria, norman f. dalton, ballarat power station, rectifier, slave clock

The clock would have been sold by William Bennett of Bridge Street, Ballarat, under his name.Timber drop case wall clock. The movement it by Ansonia Clock Company of New York United States of America, and the case is most probably of European origin.william bennett, clocks, horology, ansonia, watchmaker

This photograph is one of a series taken by Allan Quinn while travelling through France in mid-1946. There are several letters relating to this journey.This is a photograph from the Allan Charles Quinn collection which is a collection of letters and photograph depicting aspects of life at sea for a young man in the era immediately following World War II.A black and white photograph of the Great-Clock fountain (corner of Rue du Gros-Horloge and Rue des Vergetiers) in Rouen, Normandy, France, taken on the 5th of June, 1949.On reverse: ROUEN 5-6-49 handwritten in blue ink. Below this is the mark "ItI" written sideways in pencil.allan quinn, photograph, rouen, france, normandy, ww2, wwii, world war two, 1939-1945, fountain, gros-horloge, great-clock

In 1850 the Ansonia Clock Company was formed as a subsidiary of the Ansonia Brass Company by Phelps and two Bristol Connecticut clock makers, Theodore Terry and Franklin C. Andrews. Terry & Andrews were the largest clock manufacturers in Bristol at the time with more than 50 employees using 58 tons of brass in the production of about 25,000 clocks in 1849. Phelps decided to get into the clock making business to expand the market for his brass, while Terry and Andrews got access to better quality brass at better prices. They had then sold 50% of their business to Phelps and moved the business to Ansonia, Connecticut. In 1877 the clock company purchased a factory in New York and moved most of its production thereafter being spun off from the brass company. Henry J. Davies of Brooklyn, himself a clock maker, inventor and case designer, joined the newly reconstituted company as one of its founders. As President, he is thought to have been largely responsible for the figurine clocks, swing clocks and other unusual and desirable novelties for which the Ansonia firm became known. By 1879, a second factory was opened in Brooklyn, New York and by June 1880 employed 360 workers, while the Connecticut factory continued producing clocks as well with a workforce of 100 men and 25 women. Hence, clocks marked "Connecticut" were generally produced before 1879, while those marked "New York" were all produced after 1880 After the New York factory burnt down in 1880 the company rebuilt the factory on the same site, and reopened the expanded factory in 1881, with a capacity to exceed that of the Connecticut factory which by 1883 had closed. By 1886, the company had sales offices in New York, Chicago and London, with more than 225 different clock models being manufactured. In 1899, Phelps' grandson William Earle Dodge Stokes commissioned architect Duboy to build the "greatest and grandest hotel in Manhattan, New York” which became the city's first air-conditioned building. In 1929 the majority of the timekeeping machinery and tooling was sold to the Soviet government's US trading company Amtorg, just before the stock market crash. The parts, machinery and key skilled workers were shipped out of the USA to form the basis, along with the remains of a watch company purchased a year later, of the clock and watch industry in Moscow such as Poljot and Sekonda. In 1969, the rights to the use of the name, trademarks, and goodwill were transferred to Ansonia Clock Co., Inc., Lynnwood, Washington. The item marks the beginning of mass produced clocks in the United States, cheaply priced and available to all. The company had many innervation's during it’s life regards clock and later wrist watch making that led the way for other companies in many different countries to emulate.Clock, pendulum mantle model. Carved scallop "Ginger bread house" cottage clock. Oak case, white enamel face, floral etched glass door. Clock has an hour bell chime. Glass front opens to allow rewinding. Made by Ansonia Clock Co, New York. Marked "Manufactured by Ansonia Clock Co. New York, USA"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, mantle clock, clock, pendulum clock, time keeper, horology, ansonia, ansonia clock co, america

Smiths patented moving coil clocks incorporating transistors, but did not put any models on the market until 1962 when they announced the Sectronic, which had a moving coil movement. This movement had three hairsprings which served to carry current to the coils. These were one of the first battery operated clocks created. This clock is representative of 1960s timepieces. These were the first battery clocks.A small round clock with Roman numerals and gold circular design around the centre. The clock was produced by Smiths Industries Ltd. in England. It is battery powered and features the Smith Sectronic battery which was first introduced in 1962. In centre of clock face "SMITHS/SECTRONIC BATTERY/MADE IN GREAT BRITAIN" clocks, smith sectronic

Chelsea Clock Company History: The Chelsea Clock Company is an American clock manufacturing company that started before 1880 with Joseph Henry Eastman who founded the Harvard Clock Company and produced 800 clocks of marine, carriage, shelf and banjo types. He went on to change the company name to the Boston Clock Company in 1884. After several name changes in 1897, the Chelsea Clock Company was finally founded. Clocks produced by Chelsea Clock Company have been found in the White House, on US Naval Ships, and in homes and offices around the world. After the company first began life as the Harvard Clock Company, it was named the Boston Clock Company, the Eastman Clock Company before finally becoming the Chelsea Clock Company in July of 1897. The company had developed many patents and innervations over these years and between 1939 and 1946 during World War II they were awarded contracts by the U.S Maritime Commission and produced vast numbers of clocks for both merchant and naval ships. U.S Maritime Commission History: The United States Maritime Commission (MARCOM) was an independent executive agency of the U.S. federal government that was created by the Merchant Marine Act of 1936, and replaced the United States Shipping Board which had existed since World War I. It was intended to formulate a merchant shipbuilding program to design and build five hundred modern merchant cargo ships to replace the World War I vintage vessels that comprised the bulk of the United States Merchant Marine, and to administer a subsidy system authorized by the Act to offset the cost differential between building in the U.S. and operating ships under the American flag. It also formed the United States Maritime Service for the training of seagoing ship's officers to man the new fleet. The purpose of the Maritime Commission was to formulate a merchant shipbuilding program to design and then have built over a ten-year period 900 modern fast merchant cargo ships which would replace the World War I-vintage vessels Those ships were intended to be then leased to U.S. shipping companies for their use in the foreign seagoing trades the aim was to offer better and more economical freight services. The ships were also intended to serve as a reserve naval auxiliary force in the event of armed conflict which was a duty the U.S. merchant fleet had often filled throughout the years since the Revolutionary War. From 1939 through the end of World War II, the Maritime Commission funded and administered the largest and most successful merchant shipbuilding effort in world history, producing ships for both navy and merchant marine. By the end of the war, U.S. shipyards working under Maritime Commission contracts had built a total of 5,777 ocean-going merchant and naval ships. In early 1942 both the training and licensing was transferred to the U.S. Coast Guard for administration, then later to the Maritime Service final responsibility was conveyed to the newly created War Shipping Administration which was created to oversee the operation of merchant ships being built by the Emergency Program to meet the needs of the U.S. Armed Services. With the end of World War II, both the Emergency and Long Range shipbuilding programs were terminated as there were far too many merchant vessels now for the Nation's peacetime needs. In 1946, the Merchant Ship Sales Act was passed to sell off a large portion of the ships built during the war to commercial buyers, both domestic and foreign. The U.S Maritime Commission was officially disbanded on May 24th 1950. These clocks were to be found on all ships made in American for the war effort between 1939 and 1946. They are a significant reminder of the sacrifice by those who served in the merchant marine and the navy’s during the Second World War. The item is a part of our social history that reminds us of these dark times. The loses of family members, along with the trauma that many sailors had endured and had to live with for the rest of their lives once they were released from service and allowed to go home.American Clock is an 8-day marine clock made by the Chelsea clock Co for the “US Maritime Commission” . There is a second smaller dial for the seconds and 24-hour markings. Also a fast-slow adjuster to the top of the dial. The clock is an 8 day marine clock with US Maritime Commission inscribed on face in black lettering. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, clock, us maritime commission, chelsea clock company, horology, maratime clock

Donated with 2 Display Cabinets From Val Gregory The clock is a higher quality than the usual kitchen clock or gingerbread clock as they were known, with the pressed carving. Pendulum Mantle ClockManufactured By Ansonia Clock Co New York USAdomestic

This clock was manufactured by American clock company Ansonia in the late 19th - early twentieth century. Ansonia Clock was one of the major 19th century American clock manufacturers, producing millions of clocks between its incorporation in Connecticut in 1850, and its closure in 1929. In 1877 production moved from Connecticut to New York City, where inventor Thomas Edison visited the factory to experiment in combining clocks with his newly invented phonograph (an early form of gramophone). This clock is significant for its rarity due to age. A gothic style steeple wooden clock with gold and white embellishments, and Roman numeral numbering on the clock face. The interior of the clock is accessed by a hinged glass door. Under pendulum inside glass interior case: "ANSONIA CLOCK COMPANY/U.S."clock, america, american, ansonia, the ansonia clock company

This clock was placed in what was called the "Writing Room" of the Soldiers Memorial Institute when it was opened in 1921. After the renovations to the SMI in 2016 - 18 the clock was placed back in the same position in what is now called "The Building and RSL History Room".Pendulum Wall Clock, timber frame with glass front insets in door, clock face has Roman Numerals, chimes on the hour and half hour, wind up key inside. A small silver plaque is on the front bottom space.On clock face under hands, "J.T. Knowlton & Co watch makers Bendigo". Around edge of clock face, "W.M.L Gilbert Clock Co Winsted Conn U.S.A" On small Plaque, "Presented by Pioneer Comforts Fund 15.11.1921"brsl, smirsl, domestic

The mantel clock has a rich history that dates back to the 18th century. These smaller clocks were designed during an age when people wanted elegant timepieces that fit on mantels or shelves. Their compact size and decorative designs made them a popular choice for homes of the time. They graced the mantelpieces or tables in homes, serving as both functional timepieces and sophisticated decorations. These clocks often feature ornate wooden carvings and intricate designs, with their gentle ticking and chimes adding a cozy ambiance to living spaces. It was used by Henry and Martha Sebire at Mont De Lancey. It was part of the original furnishings of the dining room. Marie Colling (Sebire) is the great granddaughter of Henry and Martha Sebire.A dark brown wooden carved cased pendulum mantel clock with a highly decorated floral and column transfer design on the hinged glass front and black roman numerals and hands on the white face. It chimes on the hour.Marked inside "Ansonia Clock Co"clocks, mantel clocks, shelf clocks

This clock was originally in the front Office of the Soldiers Memorial Institute Bendigo on the mantlepiece of the fireplace. Original donor or date of being placed is unknown. It was last used in 2005 by Jack Barnes OAM who wound it every day he was in the Office, he was Secretary for 43 years of the BRSL. After the renovations to the SMI in 2016 - 18 it was placed on the mantlepiece of the fireplace in what is now called "The Building and RSL History Room"Mantle Piece Clock, timber frame, hinged glass cover over the face is missing, numbers are 1 - 12 on clock face, rear door to the mechanism, a pendulum weight is taped to the inside, no wind up key.On Clock face, "Gilbert". Around clock face, "Made in Winsted Conn United States of America"brsl, smirsl, mantle

The New Haven Clock Company from Connecticut, USA, was incorporated by clockmaker Hiram Camp (1811-1893) in 1853. Camp studied clockmaking under his uncle Chauncey Jerome (1793-1868) from the age of 17. New Haven Clock Company supplied brass clock movements to Chauncey Jerome's own business, Jerome Manufacturing Company, until that company declared bankruptcy two years later. New Haven Clock Company acquired Jerome Manufacturing Company and continued to manufacture clocks for over a century. They grew to such a scale that they were outproducing all other clockmakers in the state of Connecticut. Their 'Duna' model was created circa 1881 and features a solid walnut cabinet with ornate carvings and a glass door decorated in gold, black, and red detail. The 8-day clock is designed to be wound once per week with a key; the clock features instructions on the reverse side should the timing need adjustment.This object is part of the Burke Museum Collection and represents the detailed craftmanship of one of the leading clock manufacturers of the late nineteenth and early twentieth centuries.Decoratively carved and etched wooden eight day striking mantle clock with a white face and black roman numerals.Engraving on rim above clock face: PATD FEB.11.1879 Engraving on pendulum: PAT'D MCH.1st 1881 Reverse label: 8 Day Duna / STRIKING./ New Haven Clock Co., / NEW HAVEN, CONN. / NOTICE. / If the Clock should go too fast, lower the ball ; / if too slow, raise it. The minute hand may be / moved at any time forward, but never backward / further than the figure XII. / Should the Clock strike wrong, lift the wire / under the figure VII until it strikes right. Markings on reverse: 2496 / 3526 / 4190 / 4873 / 5936 / 71078-day clock, new haven clock company, mantel clock, hiram camp

The Seth Thomas Clock Company was founded in 1813 by renowned American clockmaker Seth Thomas (1785-1859) of Connecticut, USA, and pioneered the mass production of clocks. After Seth Thomas's death, his son, also Seth Thomas (1816-1888), continued operating the business. Their 'Adamantine' model was released in many variations. This particular model features two pillars on either side of the clockface, however other Adamantine variants could have none or up to three or four half-pillars on either side. This style of black mantle clock appears to be inspired by French clocks of the 1860s, which had gained popularity in the United States. While those clocks were often made with onyx, slate, or marble, Seth Thomas uses a durable celluloid veneer named Adamantine over a wood case to replicate the appearance of the original materials. This object is representative of the innovative manufacturing processes of pioneering clockmaker Seth Thomas and his company. Decorative black mantle clock with black and green veneer and a white face marked with black roman numeralsInscriptions: 7337 2685 6618 10508 Label on reverse [one section is illegible due to damage to label]: ADAMANTINE Label No. 295 E. / ST Trade Mark ... the / smaller end of key. To make run faster, turn to the right, slower to the left. One full turn of the key will make a difference of two / minutes in twenty-four hours. To get correct strike turn minute hand to 12 and then back to figure 9; continue doing so until proper / hour is struck. Key and Pendulum ball will be found tied or tacked to each clock. Adamantine Clock. Patented September 7, 1880. This finish is very durable, will not chip, and cannot be scratched or dented by any ordinary usage. Can be / washed or otherwise cleaned without detriment or injury to polish. Genuine Seth Thomas Clocks have Trade Mark on Movement. WHEN ORDERING MATERIAL FOR THIS CLOCK BE SURE AND GIVE LABEL NUMBER 295E. SETH THOMAS CLOCK CO. / MAKERS OF CLOCKS AND WATCHES.seth thomas clock company, adamantine, black mantle clock, horology, manufacturing

Founded in1903 when William E.Sessions and some of his family took over E.N.Welch Co. in Forestville. E.N.Welch Manufacturing Company used a local foundry to produce their castings. The foundry owner's son,William E.Sessions, took an interest in horology and ,along with other Sessions family members, bought controlling interest in the E.N.Welch Company., which was a joint stock corporation formed July 6th 1864 to succeed an older private firm who made clocks under the name of E.N.Welch. Elisha N. Welch (1809-1887),had been making clocks at a factory on East Main Street Forestville Conneticut after taking over J.C.Browns bankrupt business around 1856.Under William Sessions management the firm produced all components of their clocks including movements,cases,dials,artworks and castings.In 1930 the company expanded to produce electric clocks,timers for radios,televisions and other devices as well as their traditional brass mechanicial movements.In 1956 Sessions was absorbed by another company while retaining the name and in 1969 the business went into liquidation.Clock is made of black wood with Corinthian style columns,three set on each front corner. These are black metal, and show remains of gilt paint on top of columns.On the base of the clock is carved decoration with similar carvings on each of the four corners of square around clock face.Dial is cream with Roman numerals. the hands are set in gilt centre piece.Below the 12 is the name WELCH.The glass dial cover is edged in gilt. It is spring wound and has settings-day/night,1/2 hour strike(hour on gong -1/2 0n bell), Cathederal Gong, turn back hands. THE SESSIONS CLOCK COMPANY. Successors to the E.N.WELCH MANUFACTURING COMPANY.Forestville.Conneticut.United States of America.mantle clock, the sessions clock company, forestville conneticut united states of america

The Postmaster-General's Department (PMG) was a department of the Australian federal government, established at Federation in 1901, whose responsibilities included the provision of postal and telegraphic services throughout Australia. It was abolished in December 1975 and replaced by the Postal and Telecommunications Department. Telephone calls were transferred through exchanges by manual operators who staffed switchboards throughout the country. The clock was used to time calls in order to levy appropriate charge for telephone usage.The use of manual telephone exchanges played an important role in Australian telecommunications history, not just for day -to-day business and commercial use, but for social connections and communication during emergency. This timer has local significance as it was used at the Wodonga Telephone Exchange.A small clock used by switchboard operators to time calls at the Wodonga Telephone Exchange. Lever on the side operates timier.In centre of clock 'C. of A./P.M.G -50" Insignia of the Junghans Clock Manufacturers At the bottom edge of the time "Made in Germany",telecommunication, wodonga telephone exchange, p.m.g., timer, wodonga

The mantel clock has a rich history that dates back to the 18th century. These smaller clocks were designed during an age when people wanted elegant timepieces that fit on mantels or shelves. Their compact size and decorative designs made them a popular choice for homes of the time. They graced the mantelpieces or tables in homes, serving as both functional timepieces and sophisticated decorations. These clocks often feature ornate wooden carvings and intricate designs, with their gentle ticking and chimes adding a cozy ambiance to living spaces. It is from the home of Mr and Mrs Parker. It belonged to Mr Parker senior.A very ornately carved dark timber mantel pendulum clock with a white face and a brass clock face surround. It has black roman numerals and black metal hands. The Ansonia Clock Co. Manufacturers USA Trademark A is printed on the face. It has an ornate brass pendulum and the internal workings are visible. The very ornately embossed in gold decorated glass front door opens. There are two spirit plumb levels inside, one is aluminium metal and is attached to the wall, the other is brass with Wm Hunt Level Co with a triangle on top stamped on it. There is a brass key No.7 with two holes on the top of the winder handle. The Ansonia Clock Co. Manufacturers USA Trademark A. printed on the dial. Wm Hunt Level Co. stamped on the level.mantel clocks, clocks, timepieces, shelf clocks

Colour photograph of a clock at the Ballarat Railway Station, "Ballarat Station" written on the face of the clock.clock, ballarat railway station, horology

This business was the first Cleaning Service operating in Wodonga, later branching out into cleaning supplies. The business was owned by Charles De Guara who had migrated to Australia from Malta at the age of 16. After various jobs in Melbourne, marriage to Latvian migrant Maija and three children, he and his family moved to Wodonga in 1971. He initially worked at the Wodonga Meat Works and soon became the union delegate, initiating strike action related to inaccurate practices in recording slaughtered animals which affected workers’ payments. This action successfully secured back pay for the workers. Mr De Guara started his cleaning enterprise in 1981 while still at the meatworks and then became full-time with cleaning in 1983. He set up his showrooms in the former Wodonga Library building in Hugh Street, Wodonga. The business employed up to 25 full and part-time workers with a turn over close to a million dollars annually. In addition to cleaning, Mr De Guara sold carpet cleaning machines and vacuum cleaners to individuals as well as businesses, hospitals and clubs. Due to changed family circumstances, the business closed in the late 1980s. Mr. De Guara moved to the Mornington Peninsula district, where he passed away on 30 June 2022This item has a clear connection to a former Wodonga business.A square clock advertising the "Around 'D Clock Cleaning service. Battery powered with plastic frame and face.In Circle around face: AROUND 'D CLOCK CLEANING SERVICE" In Centre: CARPET CLEANING LOUNGE SUITES & GENERAL CLEANING LICENSED OPERATOR SCOTCHGUARD FABRIC & CARPET Protector PHONE 24 3344wodonga business, charles deguara, cleaning services wodonga

ill, maps, p.180.non-fiction A history of the Great Western railway in England, Cornwall & Wales from 1835 to 1935 reprinted from The Great Western Railway Centenary Number of 'The Times.'railroads - great britain - history, railroads - great western railway - history

ill, maps, p.455.non-fiction A comprehensive history of the Great Western railway in England, Cornwall & Wales. Volume I is from 1833 to 1863.railroads - great britain - history, railroads - great western railway - history

index, ill, maps, p.654.non-fiction A continuation of the comprehensive history of the Great Western railway in England, Cornwall & Wales. Volume II is from 1863 to 1921.railroads - great britain - history, railroads - great western railway - history

Established: Biggleswade, Bedfordshire, England in 1720 by James Pepper IGeorgianLedger Bequest, 1993Polished mahogany-cased grandfather clock with intractely decorated gold face and chased silver and brass dial. Mounted on small wooden plinth.Recto: "Tempus Fugir" engraved above clock face; "Tom. Pepper Beigelsnade" engraved on lower edge of clock facefurniture, grandfather clock, clock, face, dial, mahogany

Book was signed by the visitors for the School centenaryBlue book with gold edging and print. Stored in Black box with Gold Stars " Great Western School Centenary Visitors and Committee Names.As Abovegreat western education, realia

Chauncey Jerome (1793–1868) was an American clock maker in the early to mid 19th century. He made a fortune selling his clocks, and his business grew quickly. Jerome was born in Canaan USA in 1793 son of a blacksmith and nail-maker. He began his career in Plymouth, making dials for long-case clocks where he learned all he could about clocks, particularly clock cases, and then went to New Jersey to make seven-foot cases for clocks mechanisms. In 1816 he went to work for Eli Terry making "Patent Shelf Clocks," learning how to make previously handmade cases using machinery. Deciding to go into business for himself, Jerome began to make cases, trading them to Terry for wooden movements. In 1822 Jerome moved his business to Bristol New Haven, opening a small shop with his brother Noble and began to produce a 30-hour and eight-day wooden clocks. By 1837 Jerome's company was selling more clocks than any of his competitors. A one-day wood-cased clock, which sold for six dollars had helped put the company on the map. A year later his company was selling that same clock for four dollars. The company also sold one line of clocks at a wholesale price of 75 cents and by 1841 the company was showing an annual profit of a whopping $35,000, primarily from the sale of its brass movements. In 1842 Jerome moved his clock-case manufacturing operation to St. John Street in New Haven. Three years later, following a fire that destroyed the Bristol plant, Jerome relocated the entire operation to Elm City factory. Enlarging the plant, the company soon became the largest industrial employer in the city, producing 150,000 clocks annually. In 1850 Jerome formed the Jerome Manufacturing Co. as a joint-stock company with Benedict & Burnham, brass manufacturers of Waterbury. In 1853 the company then became known as the New Haven Clock Co, producing 444,000 clocks and timepieces annually, then the largest clock maker in the world. Jerome's future should have been secure but in 1855 he bought out a failed Bridgeport clock company controlled by P.T. Barnum, which wiped him out financially, leaving the Jerome Manufacturing Co. bankrupt. Jerome never recovered from the loss. By his admission, he was a better inventor than a businessman. When Jerome went bankrupt in 1856 the New Haven Clock Company purchased the company. One of the primary benefits of Jerome purchasing New Haven in the first place was the good reputation of the Jerome brand and the network of companies that remained interested in selling its clocks. In England, Jerome & Co. Ltd. sold Jerome clocks for the New Haven company until 1904, when New Haven purchased the English firm outright. After his involvement with the New Haven Company in 1856, Jerome traveled from town to town, taking jobs where he could, often working for clock companies that had learned the business of clock making using Jerome's inventions. On returning to New Haven near the end of his life, he died, penniless, in 1868 at the age of 74. The company struggled on after Jerome's bankruptcy until after World War II, when the company endeavored to continue through disruptions caused by a takeover along with poor sales, finally having to fold its operations in 1960 a little more than 100 years after it had been founded. The item is significant as it is associated with Chauncey Jerome who had made a historic contribution to the clock making industry during the 19th century when he began to substitute brass mechanisms for wooden mechanisms in his clocks. This was said to be the greatest and most far-reaching contribution to the clock industry. Because of his discovery of stamping out clockwork gears rather than using castings, Jerome was producing the lowest-priced clocks in the world. That can only add to his significance as the major clock manufacture of the 19th century. Jerome may have made and lost, a fortune selling his clocks but was perhaps the most influential and creative person associated with the American clock business during the mid-19th century. Also, he had served his community as a legislator in 1834, a Presidential elector in 1852 and mayor of New Haven, Connecticut from 1854 to 1855.Eight day movement wall clock with Roman numerals, octagonal shaped rosewood veneered casing, hinged face with locking clip. Wound from front. Face has adjustment for Fast-to-Slow.Part paper label on back of case can just make out "Jerome" and "ight and One" probable meaning is "Eight and One Day" describing the movements operational time between winding the mechanism.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, clock maker, jerome & co, new haven, chauncey jerome, canaan

A golden, red and white clock in the shape of a circle. Raised dots indicate time blocks. There is a golden stage attached to the clock. On the face of the clock, the make of clock is unclear, at the bottom of the face of the clock are the words 'alarm 8 days'.Metal clock with Braille and printed numbersassistive devices, swiss

An alarm clock with tactile points for numbers and raised hands and alarm hand for the time. Back of clock has settings for alarm and wind up mechanism. Has a code 470884 on the back. Clock sits on metal base.Metal clock with raised dotsassistive devices, swiss