This item is an example of a lighting device used before electricity and battery power were widespread.A small brass Elfin Reflector Night kerosene lantern with a reflector plate at the back. A handle runs around the middle. It has a small canvas wick. The glass is missing.On top of fuel tank-ELFIN REFLECTOR NIGHT LAMP On back-MADE IN U.S.A. BY EDWARD MILLER & CO USA On wicker winder (left) -E. MILLER -CO.U.S.A.lamp lantern kerosene oil lighting miller-edward

Kerosene lamp used on buggies. Has copper cylindrical base to store kerosene. Has ornate burner inside a chamber with glasss on two sides, a tin guard on one side and a small red lens on another side. It has a two tiered square tin top for ventilation.buggy, lamp, lantern, kerosene

Kerosene lamp, cast iron frame has iron ring handle, glass lamp, regulation dial at side and cap on base which contains the kerosene.Lanora Australialamp, lantern, kerosene

Lmap was hung in the old Malmsbury HotelSpherical shaped lamp made of tin, decorative features on this part, which holds the kerosene. Protruding from either side are two kerosene burners (no glass with this lamp). Lamp has a large handle lamp, lantern, kerosene

Kerosene "Hurricane" Lamp has container at the base for fuel. Has curved rounded glass to cover wickFitzall N.Y.U.S.A. (on glass)lamp, lantern, kerosene

this signal lamp was used at the Numurkah Railway StationBlack-painted tin, cylindrical in shape, with handle. Circular lens at the front with brass-coloured edging. Smaller red lens at the back with white edging. Side slot for hanging lantern onto post or hook. Round chimney/vent at the topNumurkah (metal embossing)railway, lamp, lantern, kerosene

Lamp made from metal/tin. Cylinder base to store the kerosene, with pump attachment to pump kerosene up to the lamp area. The lamp is attached to the base via a metal tube. the lamp is cylindrical with clear plastic lenses. On top of the lamp is a perforated metal cylinder for venting the fumes. on top of that is a metal circle for hanging the lamp. This is also a long screw which can be undone to access the lamp area. The whole lantern has a thick metal wire loop handle.lamp, lantern, kerosene, light

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. This lamp appears to be a modern reproduction of an earlier optional wall-mounted kerosene lamp. The lamp has been produced as an example of a 19th and early 20th-century marine kerosene navigation lamp. Marine lamp; portside metal kerosene lamp with two flat sides, and a curved front. The front has a red ridged glass lens insert and the name "port" is inscribed on a fixed brass plaque. A round chimney is on top of the lid and it has a catch. The fuel tank and wick can be removed through the base. The metal appears to be electroplated.Inscribed on the plaque; "PORT"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, lamp, ship lamp, port lamp, marine lamp, navigation lamp, port, lantern, kerosene lamp, marine technology, ship light, portable lamp

Black painted tin horizontal cylindrical shape on a cylindrical shaped base. Glass lens at the front with silver edging . Two tiered chimney for ventilation. Smaller Red lens at the back. Two protruding side pieces for hanging on hooksDietz Octo Driving Lamp New York U.S.A. (on back)lamp, lantern, driving, kerosene

Large Platform Lamp used by Railways to signal train at stoppings, Cubed in shape with angled sides. Plain glass front, Red-coloured lens on both sides, which can be opened to reveal plain glass.. Covered chimney on top . Bracket on the back to hang the lamp up. railway, platform lamp, lantern, signal, kerosene

Metal cylindrical base to store kerosene. Above this area is a cylindrical glass area for the actual lamp light. Above this is a metal cylindrical cover with perforated holes for venting fumes. A thick metal wire handle is attached to the sides of the lamp. Access to the inside of glass area is via two spring-loaded clamps on either side of the glass area.On glass: Pyrex, Aladdin, Made in Australialamp, light, lantern, kerosene

Metal (silver-plated?) cylindrical base with a column rising up to a cylindrical storage area for kerosene. On top of this are three wires protruding out from the burner area. These wires would be used to hold the glass lens (not with the lamp)lamp, lantern, light, kerosene

Metal cylindrical base to store kerosene. Metal "arch" connected to the base and holding the top metal vent in place. The top vent and bottom vents have wire metal holding the glass lens in place. There is also a wire handle Lanora Australia, on baselamp, lantern, light, kerosene

Bradley and Hubbard Co. 1869 to 1940. Pat'd 1895 - 1898.Used by a Kiewa Valley residentNickel plate body with glass chimney and large white lamp shade. Both bowl and base are panelled and the base is scrolled on the edge. The bowl has a fill cap inscribed B & H and opposite there is a ratchet wheel lift. On top of the bowl is a decorated cylinder which lifts up to enable the lamp to be lit with a match. The glass chimney sits on top. There are 3 curved equally spaced rods coming up around this cylinder - to hold up the shade.Embossed on Fill Cap lid: "B & H" Embossed on top of bowl "Dec. 1885 / No. 4 Radiant / The/ B & H" and opposite "Pat'd Aug. 16 1888" Embossed on side under the 'grate': Pat'd Feb. 16 '97" Painted on glass chimney: "Griffen - Brand / dragon logo / Fire Proof / Madein Saxony / Rochester / No. 2lamp, lantern, bradley & hubbard, kerosene, oil light

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. This particular lamp has the design of the early kerosene lamps. Its gimbal bracket and counterweight heavy base allow it to swing with a vessel's movement and still stay horizontal. The lamp is significant for its design which is an example of a 19th and early 20th-century kerosene lamp with a wall-mounted gimbal bracket and counterweight base. These features were important to vessels at sea, allowing the lamp to swing with the vessel's movement and stay vertical on rough seas.Kerosene lamp; round electroplated metal top and base, both shaped inward to join together. The base is a solid counterweight to work with the gimbal wall attachment bracket. There is no glass cover.shipwreck coast, flagstaff hill maritime museum, flagstaff hill maritime village, warrnambool, flagstaff hill, kerosene lamp, lighting, marine lamp, kerosene lantern, lamp, lantern, marine equipment, wall gimbal, wall mounted lamp, ship lamp

The kerosene lantern is a type of lighting device that uses kerosene as a fuel. Kerosene lanterns have a wick or mantle as light source. They may be hand-held for portable lighting.This kerosene lantern was used as a light on road works in the Orbost area. It would have been carried/used by one of the road workers. Lamps of this kind were significantroadworks items in their period of use as essential tools to the safe-working operations of the Country Roads Board.. A red metal roadworks warning lantern. It is rectangular with a metal carrying handle. The top is domed. The door at the back is hingedand opens with a small nail. The lamp was lit by kerosene held in a small square tank with a wick.lantern kerosene light lamp

In the beginning of the19th century, the main mode of transportation was the horse and carriage. Even after the advent of the railway, remote areas still relied on the horse for local transport.Until Australian coachbuilders began making buggies from the 1860s, most were made in America Buggies with four wheels were light but comfortable. Many had hoods to keep the sun and rain off passengers. They were generally owned by doctors, ‘squatters’ and business people. Some had small turn-out seats at the back for children. Lamps are placed at different places on the carriage sides: 1 lamp on each side placed close to box seatThese lanterns are examples of lighting devices used in the time of horse and carriage transport.Two kerosene lanterns - buggy lamps.They are rectangular in shape and have a chimney on top. Both have carrying handles.There are 3 glass windows having two clear white lights and one small red round light on the back. The ceramic burner is made by Barton's.On ceramic wick holder - B in the middle of BARTONS B Underneath is TRADE MARK lighting kerosene-lights buggy-lamps transport lanterns

These lamps belonged to Ernie Eaton and were used for spotlighting rabbits. Carbide lamps, or acetylene gas lamps, are simple lamps that produce and burn acetylene (C2H2) which is created by the reaction of calcium carbide (CaC2) with water. Acetylene gas lamps were used to illuminate buildings, as lighthouse beacons, and as headlights on motor-cars and bicycles. Portable acetylene gas lamps, worn on the hat or carried by hand, were widely used in mining in the early twentieth century. They are still employed by cavers, hunters, and cataphiles Torches, candles, oil lamps and kerosene lamps were designed to be carried around but they could be dangerous because they have flame as a source of light. These lanterns are significant examples of lighting devices widely used used before the use of battery powered devices. A pair of Germania lamps. They have brass cases with steel bodied generators and convex lens. .1 is a metal carbide coach lamp. .2 is a similar lamp but has the chimney missing. .3 is a metal handle used to attach a lamp to the front of the vehicle.Germania Base has circle with three leaves.lantern lamp germania coach-lamp

http://en.wikipedia.org/wiki/File:Tilley-storm-lantern-X246-May- Tilley storm lantern, this model has been in production since 1964 The Tilley Lamp derives from John Tilley’s invention of the hydro-pneumatic blowpipe in 1813 in England. http://en.wikipedia.org/wiki/Kerosene_lamp#Pressure_lamp Pressure lamps are far more sophisticated than wick lamps and produce a much brighter light, although they can be quite complicated and fiddly to use. This type of lamp is commonly known in the UK as a "Tilley lamp", after a manufacturer of the same name, and in North America as a "Coleman lantern" for similar reasons. A kerosene blowtorch displaying the various aspects of the kerosene burnerA pressure lamp has a fuel tank at the bottom with a small pump to pressurise the kerosene. There is a narrow gap up to the top of the lamp, called a flue, and at the top of the lamp there is a burner (gas outlet). Directly underneath the burner is the mantle, a fabric bag coated with chemicals that incandesce when heated by the gas flame. The burner lamp is known for its brightness. It is so bright because of the amount of pressure that is placed onto the wick. This pressure allows a steady flow of the gasoline and a constant light Tilley Storm Pressure Lantern, model no x246 has a stainless steel base which is filled with kerosene, with a pump used to pressurize the kerosene vapor. Under the base is a sticker.On top is a black hood with vents which sits on the glass heat resistant shade. The glass shade has an etched label. It has a white and pink mantle on the central rod with a long shaped stainless steel handle, this folds down when not in use.Base - Sticker Tilley Lamp Model X246 Etched on glass shade Tilley, Durosil, ITI, Heat Resistant. Made in Englandlantern tilley pump pressure mantle kerosene methylated spirits stainless steel lamp kerosene lamp round glass cylinder

Carl Hermann Nier in 1877 a silverware maker started to produce miners lamps and household lanterns in Beierfeld, Saxonia, East Germany. In January 1902 he established the Nier-Feuerh and company in his home town to produce kerosene lanterns. Carl's three sons Bruno, Curt and Woldemar Nier made the company into the largest lantern producer in the 1930s with Bruno Nier holding many patents for lamps. Lantern production was interrupted by World War II and ceased at the end of 1944 because of the shortage of materials and the advancing Russian army. After the Second World War the company restart the lantern production in 1947 at Luedenscheid and Hohenlockstedt north of Hamburg and fully re-establishing the company in 1950. A domestic item with an interesting history that now is sought after by collectors giving an insight into how hurricane kerosene lamps came into being from a manufacturer in Germany that held numerous patents for oil lamps from 1902 until 1940.Kerosene Lamp with handle, blue in colour, badly rusted. Lamp shade has lever to lift so you can light. Marked "Feuerhand Nr 327" "Made in Germany".flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, kerosene lamp, hurricane lamp, nier-feuerh, carl hermann nier

The period when kerosene was extensively used for indoor lighting was before electrical reticulation was installed in rural areas. In remote areas this was up to the mid 1900's. The kerosene lantern however was still in use, for camping and outdoor activities, well beyond this period and was eventually replaced by LPG and battery powered lighting. The transition phase to "modern" outdoor and domestic lighting lingered on the rural areas where the electrical reticulation suffered from reliable constant supply.In the Kiewa Valley, being a rural region, had reliable electrical domestic and farm supply only after the Kiewa Hydro Electricity Scheme had been fully operational. The supply was relative to how close the homestead was to the major electricity substation. This kerosene lamp was in use during the period when it was the only reliable source of domestic night time lighting. The strength of refractive light produced by this lantern/lamp hinged upon the size of the lamp(wick and glass bowl). The small size of this lamp suggests that it was for use in a small room(children's bedroom) or as providing a light for a safe walk to the outside ablutions (toilet) area. This small kerosene lamp has an enclosed "cup" body which would have contained the kerosene fuel. The top wick holder, made from brass, has an extended enclosed spout which raises the wick approximately 20mm from the bottom of the holder. The wick holder screws into the the top of the kerosene reservoir bowl and has a wick adjustment screw (light control) at one side. The small white glass light reflector bulb nestles securely onto the wick holder and is kept snug by snap designed extending "fingers". The section between the bottom of the refractive glass "light" bowl and the top of the kerosene bowl has perforations to allow air passage to feed directly to the wick.The light refracting bulb is open at the top to allow heat and smoke from the burning wick to escape upwards.On the wick control screw "CWB BRITISH MADE"kerosene reading lamp, domestic lighting, bedside light

This item is an important example of the early technology of artificial light. It has historical significance in demonstrating lighting devices used before the widespread use of electricity.Kerosene/oil hand-held lantern with carry handle. Red glass window (for a show of red light) and a clear glass window that opens for lighting of wick. (Dietz Dainty Tail Lamp)lantern candle dietz-dainty-tail-lamp

This item is an example of a lighting device commonly used before electricity was widely available for domestic use.A hurricane lamp with a rounded tank and small carry handle (a larger handle is possibly missing). It has a lever to open the glass tank. It has a metal base which is filled with kerosene. On top is a metal hood with vents.Around base : Chinese characters. On top : "Made in China KWANG HWA"lighting lantern kerosene-lamp hurricane -lamp

Carl Hermann Nier in 1877 a silverware maker started to produce miners lamps and household lanterns in Beierfeld, Saxonia, East Germany. In January 1902 he established the Nier-Feuerh and company in his home town to produce kerosene lanterns. Carl's three sons Bruno, Curt and Woldemar Nier made the company into the largest lantern producer in the 1930s with Bruno Nier holding many patents for lamps. Lantern production was interrupted by World War II and ceased at the end of 1944 because of the shortage of materials and the advancing Russian army. After the Second World War the company restart the lantern production in 1947 at Luedenscheid and Hohenlockstedt north of Hamburg and fully re-establishing the company in 1950. A domestic item with an interesting history that now is sought after by collectors giving an insight into how hurricane kerosene lamps came into being from a manufacturer in Germany that held numerous patents for oil lamps from 1902 until 1940.Kerosene lamp with handle, red in colour, badly rusted. Lamp shade has lever to lift so you can light it.Marked "Feuerhand Nr 327" "Made in Germany".flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, lamp, kerosene lamp, hurricane lamp, nier-feuerh, carl hermann nier

Sherwood Ltd. Was a manufacturer of oil lamps and burners at the Nechells Park Works Birmingham UK and regarded at the time as a renowned name in the oil lamp and burner manufacturing industries in Birmingham during the early part of the 20th century. They started selling as ‘Isaac Sherwood & Son Ltd.’ in 1904, later around 1920 they merged with Linley and Co makers of American pattern lamps and became ‘Sherwood-Linley” moving to 44-50, Granville St. Birmingham. They became one of the largest manufacturers of lighting devices and burners in England. They produced all sorts of illumination devices and became famous for their oil burners. Apart from oil burners, they produced table and floor lamps, sconces, lanterns and chandeliers that made Sherwood unique. A Significant item as part of a kerosene lamp that was commonplace in homes and other premises during the early 20th century as a means of lighting before electric lighting became the standard. These types of items give a snapshot into domestic and social life during this period.Lamp Burner housing, brass with wick-screw (no wick). Made in England Sherwoods LTD Birminghamwarrnambool, flagstaff-hill, shipwreck-coast, flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp burner, sconces, kerosene lamp, wick adjuster, sherwood & son ltd, sherwood-linley

The Feuerhand lantern works were established in Beierfeld in the Saxon Ore Mountains. Called Erzgebirge in German or Krušné hory in Czech, is a mountain range in the south of Saxony in Germany known for its craftwork. Lantern production began in the area by Hermann Nier who ran a plumber's workshop around the 1870s and made lanterns, amongst other things. In the town of Beierfeld, also well-known for its metalworking were the brothers Hermann and Ernst Nier who founded a modern production centre for hurricane lanterns manufacture in 1893. Five years after the foundation, the company Frankonia (Albert Frank metalware) bought up the production site and the brothers Nier became production managers. Owing to differences with Frankonia, Hermann Nier finally started its hurricane lantern factory "Hermann Nier Feuerhandwerk" in 1902. In the same year, he applied for a patent for the manufacturing of lanterns using the stamping and folding techniques with tinning by hot-dipping and without hand-soldering. In 1914 the trademark "Feuerhand" was registered for all products as a utility model of the German Reich in German: "Deutsches Reichs-Gebrauchsmuster" (DRGM) and in 1920 the round Feuerhand emblem was added to the brand. Finally, in 1926 the patents, as well as the trademark "Firehand", were also registered in the USA. The manufacture of the well-known small hurricane lanterns the “Baby Series” complete with fireproof borosilicate glass from the Firma Schott firm from Jena started in 1933. Between 1918 and 1938 Nier Feuerhand became the biggest producer of hurricane lanterns in the world. Production continued until 1990.A significant item that demonstrates from its fabrication a manufacturing process that was far in advance of its time and that influenced the production of lanterns from many other manufactures around the world. These types of lanterns made by Feuerhand around the early 20th century are now sought after by collectors.Monarch style Lantern painted black. Made in Germany has Freuerhand, manufactures logo on filler cap and top of lamp centre postflagstaff hill, warrnambool, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, hurricane lantern, kerosene lamp, feuerhand lantern works, albert frank metalware, hermann and ernst nier

The subject item was produced in 1914/15 by the Telford Grier and Mackay Company in Glasgow, Scotland, this lantern was not used to provide visibility for Sailors on a ship, rather, it is meant to help other vessels identify the ship’s presence and heading in low visibility conditions hence it is marked Port and has a red filter. The lantern would have been placed along the port side of larger vessels to provided an unbroken light and would be visible in an arc from as well as at an angle from the port side of the vessel. The company was established in 1904 at 11 Fairley Street Glasgow and in 1922 moved to 10 Carrick Street. The company manufactured patented lamps for marine use, later moving into the manufacture of electrical and mechanical items. A significant marine kerosene lantern made by a company that patented this type of lantern for use by the British Navy and for merchant ships the world over. This item today is rare and sought by collectors.Ship's port side sidelight lamp with clear glass frenal lens with red filter behind, burner missing, replacement with modern electric fittingTwo makers lozenges one marked PORT the other has the maker Telford, Grier and Mackay, Glasgow, 1915 marked on main body chimney has 1914 marked . Also serial No C976 stamped on backplate.flagstaff hill, warrnambool, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp ship's sidelight, ship's sidelight lamp, port lamp, marine light, navigation light, kerosene ship lamp

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. An anchor lamp like the lamps in this pair would be raised on the highest ship mast at night to signal other seafarers that the ship was at anchor or sailing at night. The metal loops on opposing sides of the lamp could hold a pair of rods or ropes. and be used to raise the lamp.The lamp is made to the design of a 19th and early 20th-century kerosene anchor lamp carried as essential marine equipment and used as a signal lamp on sailing ships. Lamps; a pair of cylindrical kerosene anchor lamps. Each has a flat back, a hinged door, a metal handle and two metal loops or guides fixed on each side. The glass window is convex and inside the lamp is a wick in an enamel wick holder.brass lamp, lamp, anchor kerosene lamp, kerosene lamp, marine equipment, marine lamp, navigation, light, ship light, ship lamp, lantern, maritime, nautical, safety lamp

The item is a kerosene marine ships lamp used onboard ships and smaller vessels for general lighting and navigation the subject lamp was made by a very well known maker R C Murray of Glasgow Scotland. During the research several different addresses were found but nothing on the founder or company history. It appears RC Murray made not only marine lamps but lamps for the railways as well. The company is listed in the Scottish Post Office Directories for 1885 to 1886 as manufacturing tinsmiths, lamp makers, coppersmiths, gas fitters, bell hangers and workers in sheet iron, zinc and brass at street numbers 7, 9 and 11 Carlton Court, Bridge St Glasgow. An additional address is at 37 Cavendish St Glasgow listed for 1910, and also at Pollokshaws Road. The writer assumes the company must have moved sometime between 1886 & 1910 to these addresses. The writer at this time cannot ascertain any more historical information regarding the company or its founder, however, lamps made by RC Murray are now collector's items commanding significant sale prices on many auction websites.A significant item used in the marine industry on many ships, the company made kerosene lamps for other industries as well and was a well-known company in the early part of the 20th century.Marine kerosene ships lamp, round copper handle on top and side top is hinged with catch and lever, protruding near top.Inscribed "RC Murray and Co Limited" "Pollokshaws Road Glasgow S.1." flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp, lantern, brass lamp, nautical object

The company was originally founded by Frederick Perkins a Russian immigrant schooled in Germany as a machinist and tool and die, maker. Frederick came to the United States in the early 1890s and soon became employed as a machinist for E.W. Bliss & Company in Brooklyn, New York. In the early 1900s, he and a partner began operating a business, F. Persky & Company, Lantern Manufacturer, out of the basement of his house. In 1907, Frederick's son Louis joined him in the business, and together they enlarged both the product line and the manufacturing facilities. By 1912, they had seventeen employees and made a wide range of marine lanterns and products. The business continued operating until 1913 when Frederick became president of National Marine Lamp Company, based out of Forestville, Connecticut. Frederick and Louis left that company in 1916 and moved back to Brooklyn, New York, where they started Perkins Marine Lamp Corporation. Five generations later, PERKO is still a privately owned, family-operated corporation. Perkins Marine Corporation was initially known as Perkins Marine Lamp, Inc. The original focus was on the manufacture of hand-formed sheet metal products for the marine market. The first “Perko” catalogue was published in 1916. It included a full range of kerosene and electric lanterns for small and large boats, ventilators, chart cases, signalling devices, mooring buoys, pumps and a variety of spare parts. These products, fabricated from brass, copper and galvanized sheet metal, began a reputation for producing high-quality products. In 1922, the "PERKO" trademark was instituted with each new product utilising the latest, sophisticated metal manufacturing technology.A significant item from an American manufacturer that specialises in making marine products and is still in business today under the same trade name. The subject item is significant as it was made not long after the trade name of PERKO was registered in 1922 and began to be used on the company's various products.Kerosene lamp with circular fuel tank and chrome plated reflector shield. "PERKO" stamped on base.warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, kerosene lamp, marine lamp, perko inc, lighting, marine accessories manufacturer