The Ballarat School of Mines building along Albert Street were moved or demolished to make way for the new Engineering Workshop. William Henry Middleton was President of the Ballarat School of Mines from 1912 to 1940.Particulars for removal of the Ballarat School of Mines Caretaker's Quarters and Cyanide buildings are handwritten onto a foolscap page (.1). Three plans are hand-drawn in pencil, these are: (.2) Cyanide Building (.3) Caretaker's Quarters (.4) Caretaker's Quarters - South End Elevationballarat school of mines, new engineering workshop, j.h. brown, william middleton

The 5 tender documents relate to the removal of Ballarat School of Mines building from along Albert Street Ballarat in preparation for the construction of a new Engineering workshop.Five pages relating to the removal to the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters. (.1) Blue tender form to the Public Works Inspector from J.H. Brown of Dana Street Ballarat relating to the removal to the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters fro 40 pounds (.2) Letter on white ruled paper with F.& J.W. Gower letterhead relating to a tender to remove the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters for 70 pounds (.3) Letter on white paper from William Dillon of 38 Humffray Street Ballarat East converning the relating to a tender to remove the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters for 95 pounds 17 shilling (.4) Letter from G. Ludbrook & Son on white, ruled, foolscap paper relating to a tender to remove the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters for 98 pounds 17 shillings and 6 pence (.5) Letter from A. Delaland on white ruled paper relating to a tender to remove the Ballarat School of Mines Cyanide Plant and Caretaker's Quarters for 105 pounds and 15 shillings.ballarat school of mines, cyanide plant, caretaker's quarters, caretakers cottage, jh brown, f gower, jw gower, william dillon, g ludbrook, a delaland, public works department

The Ballarat School of Mines was the first school of mines in Australia.Exercise books of newspaper clippings relating to the Ballarat School of Mines. Clippings include: 12 Feb 1936 - State Scholarships 12 March 1936 - Dr J.R. Pound 19 March 1936 - MacRobertson Scholarship 23 March 1936 - gift to the museum - Wardle and Jermyn donate timber specimens 11 May 1935 - A.W. Steane 13 June 1936 - Frederick Longhurst appointed art instructor 27 July 1936 - Ballarat Junior Technical School Reunion 11 Sept 1936 - Wiltshire Poster Competition 30 Oct 1936 - Dressmaking classes 20 NOv 1936 - Nornie Gude NOvember 1936 - Ballarat School of Mines Reunion 16 March 1937 - Oval for Ballarat Junior Technical School - White Flat 11 Nov 1937 - Poster competition - Betty Brown and Albino Paganetti 08 Feb 1938 - Frederick J. Martell obituary 07 July 1938 - Henry Kum-Yuen 14 July 1938 - Red Cross Competition for Women 06 Aug 1938 - School Pine Plantation at Vale Park 19 Aug 1938 - Memorial trees planted at Ballarat Junior Technical School to the memory of Cliff Ellis and Ken Butler 06 March 1939 - Ballarat School of Mines Reunion 16 May 1939 - Ballarat School of Mines Battery 19 April 1940 - Progress of Technical Education - New Engineering workshop opended by Sir John Harris 03 June 1940 - W.H. Middleton obituary 16 July 1940 - Training munition workers 30 May 1941 - Lady Tracers 19 Oct 1942 - War Poster competition 24 February 1944 - Ballarat School of MInes Record Enrolments Feb 1944 - D.F.C. for Ballarat Airman H.J. Trevenen 11 Feb 1945 - Harold Herbert Obituary 14 Oct 1945 - Technical Schools in Wartime 23 Feb 1946 - Molasses and Chaff for SMB Initiates 06 June 1946 - Plans for Victory Ball 13 Sept 1946 - Ken Walker sculpts Prime Minister Chifey's bust 23 Aug 1946 - Edgar McConnon obituary 24 Oct 1946 0 Retirement of A.F. Heseltine 25 Nov 1946 - Army huts for classrooms 12 Dec 1946 - Proposed New Theatre for Ballarat by Geoff Richards 16 Dec 1946 - Ballarat Junior Technical School Old Boys who served in armed forces during World War Two 28 July 1947 - Pottery section at Ballarat School of Mines 31 July 1947 - Red Cross Hut removed to the Ballarat School of Mines 10 March 1948 - Guncotton Factory buildings to become nurses quarters 18 March 1948 - Samuel Mayo Obituary ballarat school of mines, ballarat techncial art school, swimming shield, ballarat school of mines museum, ballarat war museum, sydney pern, t.m. pescott, c.w. brazenor, victory ball, w. rowe, joan walker, graeme dowling, ken walker, prime ministers' avenue, ben chifley, amalie feild, amalie colquhoun, h.h. smith, portrait, girls' preparatory classes, world war two, w. williams, raaf, w.s. williams, william william, william williams, new workshops, herbert j. trevenen, harold herbert death, les crouch, swimming, ballarat city baths, heather scott, clunes hospital nurses' quarters, ballarat ladies' art association scholarships, samuel henry mayo, samuel mayo death, girls preparatory classes, w. william, pilot, killed in action, education reform, ballarat schoool of mines museum, h.j. trevenen, world war ii, world war 2, ballarat junior technical school war service, nurses quarters, guncotton factory building, s. mayo death, initiation, ballarat school of mines scrapbook, newsclippings, j.r. pound, macrobertson scholarship, a.w. steane, ballarat junior technical school, wiltshire's poster competition, ballarat junior technical school old boys' association, ballarat junior technical school old boys' reunion, nornie gude, a. nye, albino paganettu, betty brown, dorothy woolcock, jean coates, jack hewitt, hazel robinson, gilda gude, white flat oval, gauge tower demolition, a.f. hesiltine, darwin, victor greenhalgh, frederick martell, memorial trees, cliff ellis, valda king, pharmacy, reunion, engineering workshops, thomas k. sim, daylesford, battery, h.h. smith reunion, ballarat technical art school reunion, w.h. middleton obituary, munition makers, plumbers, pottery industry, girls education, munition trainees, lady tracers, waterloo prize money, war museum, art as vocation, art education, nine-inch telescope, returned soldiers' league, repatriation classes, pinkertson scholarship, amel robert gordon, projector, pethard cup, ballarat food appeal for britain, queen mary, ballarat swimming pool, ballarat school of mines initiation, swimming carneval, prime ministers avenue, edgar mcconnon, community theatre project, world war two service, john l. burt, hockey, pottery, ceramics, ballarat school of mines coat of arms, coat of arms, k. bremner, red cross hut, s.m.b. follies, ken palmer, s. mayo, chinese, albert steane, university women, a.f. heseltine, student activity, swimming sports, albino pagnetti, w.h. middleton death

Built by the Buffalo Forge Company in New York, USA. It is of a typical hand operated design used in workshops. This item was probably used in an engineering shop locally.A cast iron workshop drill. It has two spanner holes.On wheel at top - BUFFALO FORGE Co. and on frame BUFFALO N.Y.drill press workshop hand-operated

Series consists of a large collection (over 1150) of negatives of scenes, activities and staff of the Shire of Eltham. Many of the films were taken for publicity purposes and necessarily cover a broad range of topics. The films or individual strips have been organised into Scenes, Activities and Staff groupings, however there are many overlaps. 1) Scenes includes: Parks and Roads including Alistair Knox Park, Tree Planting, Trees and Flowers, general Shire Scenes. One of the Alistair Knox Park films also contains shots of the Shire President (John Graves?) in the Chambers wearing the Presidential Chain. 375 negatives. 2) Activities documented include: Fire Safety workshop and massage, Leisure Centre activities including pool construction, Living and Learning Centre, Pottery, Netball, Shire Offices, Elderly Citizens, Buildings, Youth Services, Sporting Facilities, Parklands, Community Arts, Childca re, Childrens Week Book Launch 23/ 10/1991 , Environment Week Launch 19/9/1991 , Childrens Services and Activities, Buy A Book Campaign Launch November 1990, Thelma Barkways' Birthday 1990, Engineering activities including Waste Collection, Building and Health Services activities including water testing, examples of new housing, blocks of land, letter box numbers. Also in this section are Shire Office and Handbook shots, nature shots including butterflies (Eltham Copper Butterfly?), wheelchairbound CEO Rodney Roscholler, Community Services Xmas Lunch 1991. 607 negatives. 3) Staff including many groups and individuals to be identified, Rodney Roscholler, Thelma Barkway, Councillors, Shire President Pamela Sladden, Roma O'Callaghan, Irene in the Kitchen/Entertainment Area, also Farm Scenes. 169 negatives.shire of eltham archives, series listing

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.Black and white photograph of the Davey Paxman Experimental Steam Engine. On the brake is returned serviceman Norman WIlliam Ludbrook (Diploma Electrical Engineering, 1952). Far right is Roy E. Mawby (Diploma Electrical Engineering, 1950)steam engine, model steam engine, davey paxman, electrical engineering, laboratory, scientific instrument, norman ludbrook, norman william ludbrook, roay mawby, roy e. mawby

The Working Men's College later became the Royal Melbourne Institut of Technology (RMIT), and is now RMIT Univesity.Charcoal green soft covered magazine of the Working Men's College. Articles include: * On the Beginning of Things (Robet Haddon) * An Annual Out-door day * Powlett Coal * The Arts and Crafts Society * Gordon College * Big Guns * The Aeroplane * The Department of Engineering (W.M. Kernot) * British Craftsmanship (Robert J. Haddon) * The Education of an artist in Australia (Archibald Colquhoun) * The Ordeal of Eyes * Modelling and the Sculptors Art (J.S. Davie) * Wrought Iron - Old & NEw (John G. Lothian) * Some Lately Departed Students. (A. Coates, S. Rennick, W. McLean, J. Douglas, H. Colwell, L. Ritchie, B. Caldwell, V. Bowen, W. Williams, T. Richardson., L. Leslie) * Sport * Correspondence * NEws from Fiji (J. Herbert Beath) * A Student in China (R.C.S. Ogilby * College Examination Results, 1909 Images: Wilfred N. Kernot, Engineering classes and rooms, Blacksmithing workshop, Antique drawing roomc. dowel, working men's college, rmit

Background to the two openings of the "Goat Shed": Following a need to clean up some of the old L&L Centre buildings, in 1989 Council decided to enclose the remaining goat shed in a steel truss frame for use as a store room. Claire Fitzpatrick, who had run animal husbandry and goat classes on the site from the 1975 opening of the L&L Centre, was invited by the Committee to officiate at the naming of the new building on 3/12/1989. Following a fire of the stables/workshops on 8/5/1990 (which had to be cleared off the site) Council/Committee decided to use the $15000 insurance money to upgrade/refurbish the 1989 building to replace classrooms lost in the "stables fire". This refurbished Goat Shed was officially opened on 30/5/1991 by Cr. Peter Graham, Shire President. (Gleaned from Committee file, 1987-1992.) Photos show Cr Graham plus Gillian Barclay (Co-ordinator), Liliana Unsworth (Engineering Design Draftsperson) and Bill Oakley (Corporate Development Officer). Colour photographeltham living and learning centre, goat shed, gillian barclay, peter graham, liliana unsworth, bill oakley

Background to the two openings of the "Goat Shed": Following a need to clean up some of the old L&L Centre buildings, in 1989 Council decided to enclose the remaining goat shed in a steel truss frame for use as a store room. Claire Fitzpatrick, who had run animal husbandry and goat classes on the site from the 1975 opening of the L&L Centre, was invited by the Committee to officiate at the naming of the new building on 3/12/1989. Following a fire of the stables/workshops on 8/5/1990 (which had to be cleared off the site) Council/Committee decided to use the $15000 insurance money to upgrade/refurbish the 1989 building to replace classrooms lost in the "stables fire". This refurbished Goat Shed was officially opened on 30/5/1991 by Cr. Peter Graham, Shire President. (Gleaned from Committee file, 1987-1992.) Photos show Cr Graham plus Gillian Barclay (Co-ordinator), Liliana Unsworth (Engineering Design Draftsperson) and Bill Oakley (Corporate Development Officer). Colour photographeltham living and learning centre, goat shed, gillian barclay, peter graham, liliana unsworth, bill oakley

Background to the two openings of the "Goat Shed": Following a need to clean up some of the old L&L Centre buildings, in 1989 Council decided to enclose the remaining goat shed in a steel truss frame for use as a store room. Claire Fitzpatrick, who had run animal husbandry and goat classes on the site from the 1975 opening of the L&L Centre, was invited by the Committee to officiate at the naming of the new building on 3/12/1989. Following a fire of the stables/workshops on 8/5/1990 (which had to be cleared off the site) Council/Committee decided to use the $15000 insurance money to upgrade/refurbish the 1989 building to replace classrooms lost in the "stables fire". This refurbished Goat Shed was officially opened on 30/5/1991 by Cr. Peter Graham, Shire President. (Gleaned from Committee file, 1987-1992.) Photos show Cr Graham plus Gillian Barclay (Co-ordinator), Liliana Unsworth (Engineering Design Draftsperson) and Bill Oakley (Corporate Development Officer). Colour photographeltham living and learning centre, goat shed, steve, alan

Background to the two openings of the "Goat Shed": Following a need to clean up some of the old L&L Centre buildings, in 1989 Council decided to enclose the remaining goat shed in a steel truss frame for use as a store room. Claire Fitzpatrick, who had run animal husbandry and goat classes on the site from the 1975 opening of the L&L Centre, was invited by the Committee to officiate at the naming of the new building on 3/12/1989. Following a fire of the stables/workshops on 8/5/1990 (which had to be cleared off the site) Council/Committee decided to use the $15000 insurance money to upgrade/refurbish the 1989 building to replace classrooms lost in the "stables fire". This refurbished Goat Shed was officially opened on 30/5/1991 by Cr. Peter Graham, Shire President. (Gleaned from Committee file, 1987-1992.) Photos show Cr Graham plus Gillian Barclay (Co-ordinator), Liliana Unsworth (Engineering Design Draftsperson) and Bill Oakley (Corporate Development Officer). Colour photographeltham living and learning centre, goat shed, alan

Background to the two openings of the "Goat Shed": Following a need to clean up some of the old L&L Centre buildings, in 1989 Council decided to enclose the remaining goat shed in a steel truss frame for use as a store room. Claire Fitzpatrick, who had run animal husbandry and goat classes on the site from the 1975 opening of the L&L Centre, was invited by the Committee to officiate at the naming of the new building on 3/12/1989. Following a fire of the stables/workshops on 8/5/1990 (which had to be cleared off the site) Council/Committee decided to use the $15000 insurance money to upgrade/refurbish the 1989 building to replace classrooms lost in the "stables fire". This refurbished Goat Shed was officially opened on 30/5/1991 by Cr. Peter Graham, Shire President. (Gleaned from Committee file, 1987-1992.) Photos show Cr Graham plus Gillian Barclay (Co-ordinator), Liliana Unsworth (Engineering Design Draftsperson) and Bill Oakley (Corporate Development Officer). Colour photographeltham living and learning centre, goat shed, gillian barclay, peter graham, liliana unsworth, bill oakley

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.Black and white photograph of the Davey Paxman Experimental Steam Engine installed at the Ballarat School of MInes. steam engine, model steam engine, davey paxman, thomas bath, experimental steam engine

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only. Black and white photograph of an experimental steam engine which was produced for the Ballarat School of Mines. It was designed for experimental purposes, such as testing of efficiency, etc. The laboratory which housed the steam engine was lit with gas lighting. davey paxman experimental steam engine, model steam engine, davey paxman, steam, thomas bath, thermodynamics

The Davey Paxman Experimental Steam Engine was purchased by the Ballarat School of Mines as the result of a bequest from Thomas Bath.The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.davey paxman experimental steam engine, model steam engine, steam, thermodynamics laboratory, thomas bath, bequest

This building has been demolished to make way for new buildings along Albert Street. According to E.J. Barker this was Metal Fabrication.Plans (dyeline) for new building along the Ballarat School of Mines Albert Street frontage .1) Ballarat School of Mines New Workshops .2) as above Scale 1:480 WGS 84 37 degrees 33 feet 54 inches south 143 degrees 50 feet 30 inches eastSheet No 3 F.G.B.ballarat school of mines, metal fabrication, albert street, buildings, plan, heat engines room, model mine, blacksmiths shop, blacksmithing, carpenters shop, engineering shope, percy everett

In 1947 Percy Everett, Chief Architect for the Victorian Government, drew up plans to accomodate the growth in student numbers on the Ballarat School of Mines site. It was an era of government buildings surrounding the Ballarat School of Mines campus either being transfered to the school or foreshadowed for transfer. In 1947 two Red Cross huts were transferred from Victoria Park to the western side of the former Ballarat Supreme Court (later Courthouse Theatre) for use by Wool Classing and Motor Mechanics. In the same year additional facilities were provided for Pottery due to the increase in enrolments and a large brick classroom was built at the rear of the Ballarat Junior Technical School Building. In the annual report of 1947 the President said: "These transfers are, however, only temporary expedients and indicate the pressing need for more buildings of a permanent nature". By the end of the year the School Council decided to request the Education Department of Victoria to proceed with the implementation of the School's long-range plan whch had received approval earlier and to treat it as an urgent post-war requirement. After much communication a plan for a six-storied building, flanked by two three storied buildings was planned to be built on the site of the Ballarat Gaol was developed. The plan was sent to the Education Department for the Minister's Approval. It is not know if approval was granted, but the building did not proceed, possibly becausse the Ballarat Gaol was still very miuch in use. When a tertiary division of the Ballarat School of Mines was being developed in 1967 it corresponded with the closure of the Ballarat Gaol. It was determined that the Lydiard Street South site had no room for future growth so a new campus was sought. The new campus was purchased at Mt Helen, and was initially known as the Ballarat Insittute of Advanced Education. In 1976, when the Ballarat Teachers' College merged into the structure, the campus became known as the Ballarat College of Advanced Education and it was no longer a part of the Ballarat School of Mines. Plans for a proposed building to replace the Ballarat Gaol buildings. The proposed building was never built, the concept being replaced by a new teritary facility at Mt Helen. buildings, percy everett, ballarat school of mines battery, ballarat technical art school, engineering workshops, machine shop, ballarat junior technical school, architectural plans, ballarat school of mines, smb campus

On 11 June 1987 The M.B. John Trade–Art building (Albert Street front) of SMB was officially opened by the Hon. John Cain, Premier of Victoria, in the presence of Morgan B. John. Programs include 3 Dimensional Art, Painting & Decorating, and Engineering Trades. (SMB Institutional Plan 1989)Large format copy of a drawing projecting the new M.B. John Building into the Ballarat School of Mines environment. The view is from within the School of Mines in close proximity to the Ballarat School of Mines Botanical Gardens. ewan jones and associates, architects, m.b. john building, m.b.john, morgan b. john, morgan bevan john, ballarat school of mines, buildings

Specification or report - 6 A4 pages, photocopied titled "A class tram - Melbourne, Australia". Gives the detail of the tramcar, classification, developers (builders and suppliers), description, history, vehicle performance, dimensions, suspension, propulsion, braking, electrical and control systems and body specifications and a list of work done at Preston Workshops.trams, tramways, a class, commonwealth engineering, comeng, aeg, duwag, bogies, the met, new trams

Set of hand written notes, plain paper, stapled together, 12 sheets listing: Tram Number - date to Preston, Lowered onto trucks, truck number, mobile allocated to depot and notes Fault list on trucks, Dimension and other notes Tram destination roll for East Preston. Condition poor.trams, tramways, z class, comeng, commonwealth engineering, preston workshops, bogies, destination roll, new trams

Photocopy - report - of a The Met Memorandum dated 28 Oct. 1988 - 5 A4 Sheets stapled in the top left hand corner titled "W Class Tram Overhaul" from the Asset Development Co-ordinator to the Director, Engineering Maintenance and Construction. Memo looks at the concept of overhauling some 120 W class trams, project proposals, project need, alternatives, installation of AVM's, ticket machines, benefits, costs, compared to the cost of new trams, timing. Last sheet of the memo looks at the Preston Workshops capacity for such a project.written in ink on front cover "Includes comments on related PW Shop capacity for the overhauls"trams, tramways, w class, the met, preston workshops, overhauls

Specification or report - 5 A4 pages, photocopied titled "Z3 class tram - Melbourne, Australia". Gives the detail of the tramcar, classification, developers (builders and suppliers), description, history, contract price, warranty, vehicle performance, dimensions, suspension, propulsion, braking, electrical and control systems and body specifications and a list of work done at Preston Workshops.trams, tramways, z3 class, commonwealth engineering, comeng, aeg, duwag, bogies, mmtb, new trams

Folder of Memos and directions (htd3207i1> htd3207i8) - Air raid precautions, covering painting, respirators, sheds, tools, kits, shelters, stacks , blackouts, trenches, emergency, air raid shelters (htd3207i9> htd3207i16) - Accidents, covering accidents and derailments, (htd3207i17) - Bridges – inspection of Victoria St bridge (htd3207i18) - Cable tracks, covering tarring, patching, top dressing of cable tracks (htd3207i19> htd3207i21) - Cartage, covering hired trucks, cartage of wood blocks, spoil, sleepers (htd3207i22> htd3207i23) - Contracts, blank page (no image) - Councils, covering track opening, storm water drain, bad roads (htd3207i24) - Costs, covering maintenance costs, construction costs, wet weather (htd3207i25> htd3207i26) - Depots, covering inspections, storage, paving, telephones, mail (htd3207i27> htd3207i30) - Derailments, covering controls, reports (htd3207i31) - Drainage (htd3207i32) - Eastern Lines, covering loading platforms, crossovers, work orders (htd3207i33> htd3207i34) - Eastern Lines Reconstruction (htd3207i35> htd3207i37) - Eastern Line Maintenance (htd3207i38> htd3207i40) - Estimates (htd3207i41) - Employment (htd3207i42) - Footscray Lines (htd3207i43) - Instructions (htd3207i44) - Journals, covering Engineering Journal and magazines (htd3207i45) - Materials – General, covering frames & covers, unloading stores, packing plates, petrol allowance, ashes at Preston workshops, electrodes, sleepers (htd3207i46> htd3207i50) - Maintenance – General, covering loading platforms, inspections, work orders, paving (htd3207i51> htd3207i57) - Northern Lines, covering greasing of curves, crossovers, loading platforms (htd3207i58> htd3207i61) - Northern Lines – Reconstruction, covering crossings, welding machines (htd3207i62> htd3207i64) - Northern Lines – Maintenance, covering repairs, crossings, lifting programme, fencing, curves, track inspection, repairs (htd3207i65> htd3207i70) - New Lines (htd3207i71> htd3207i80) - Plant – General (htd3207i81> htd3207i94) - Plant – Concrete Mixers (htd3207i95) - Plant – Motor Vehicles (htd3207i96> htd3207i100) - Plant – Rollers (htd3207i101> htd3207i103) - Plant – Grinders (htd3207i104) - Plant – Grinders & Scrubbers (htd3207i105> htd3207i110) - Plant – Compressors and Tie Tampers (htd3207i111) - Plant – Cleaner Cars (htd3207i112> htd3207i114) - Plant – Loaders (htd3207i115) - Plant – Tools (htd3207i116> htd3207i117) - Plant – Miscellaneous (htd3207i118) - Per Way – General (htd3207i119> htd3207i121) - Public Utilities (htd3207i122> htd3207i123) - Reconstruction – General (htd3207i124> htd3207i126) - Railways (htd3207i127> htd3207i129) See \dbtext\hawthorn\photo_collections\3207_Folder for scanned images.trams, tramways, instructions

Set of 6 reports, photocopied onto heat sensitive paper from various magazines. Documents match the image numbers. .1 - .2 pages - Electrical Engineer - 15/8/1928 - "Rail Grinding Machine for Melbourne Tramways" - Grinders .2 - 5 pages - Electrical Engineer - 15/6/`1927 - "Workshop of the Melbourne Tramways Board" - includes a layout drawing - See Reg Item 3675 for a reprint of this document. .3 - 1 sheet - Electrical Engineer - 15/9/1927 - "Worm Driver for Electric Tramcars - new type of truck constructed by Melbourne Tramways Board" - fitted to X1 class cars. Has a sketch of the truck. .4 - 8 pages - The Electrical Engineer and Merchandiser - 15/11/1933 - "A Supervisory Control system for Traction Substation - Equipment designed for the MMTB" - written by C. L. Steele. .5 - 8 pages - "Institute of Engineers Australia" - Dec. 1943 - "Prolonging the life of the tramway rail" - by A. H. Blanch. Note some pages have handwritten additions where the copying is out of line. .6 - 1 page - The Electrical Engineer and Merchandiser - 16-10-1950 - "Noiseless bogie for Tramcars" - PCC bogies. - St Louis Car C B-3 Bogie.trams, tramways, mmtb, rail grinding, rail wear, track materials, grinding, preston workshops, worm drive, x1 class, substation, electrical engineering, electrical equipment, tramway per way, bogies, pcc class

.0 - Autumn 1980 - Passenger counting, Survey provides data, We lead the way with Z3, Wattle Park, transport in Moscow, Spike Milligan, Melbourne's decorated trams, transporting art, sports, training, and Raymond Stock, Assistant Traffic Manager Revenue .1 - Winter 1980 - Bourke St Mall is popular, Senior citizens help design new tram (Z3), A bus-only lane in Johnstone St., Depot Employees' Social and facility Melbourne. Has a profile on Mr R. C. Drummond, Traffic Manager. .2 - Spring 1980 - Christmas Message, supporting those children with polio in 1938, Trolley buses, Z3 trams being built, use of parafil in overhead, cleaning truck. Has a profile on Ken Hall, Assistant Chief Engineer - Mechanical and Reg Robinson who was the organiser for the 1938 polio event - bus driver / instructor. .3 - Summer 1981 - MMTB involvement with Australia Day pageant, note involvement of TMSV, Bendigo, BTPS 27 (26 Jan. 1981), film on apprentices, tram stop shelters, resilient track work, trolley buses, the supply and systems department including Hawthorn clothing workroom and printing department (photos) and profile on Mr Jerry Compton, Supply and systems department. (Two copies held) .4 - Autumn 1981 - new buildings at Footscray, South Melbourne, trolley buses for Melbourne?, building MAN buses, why join the Tramways Benefit Society, article that looks at the Engineering Branch and profile of John Grigg, Chief Engineer. (Two copies held) .5 - Winter 1981 - New passenger shelters, image of the Elizabeth St shelter proposal, where do old trams go?, "Around the Clock" Emergency Service (item on R10) (See Reg item 1004 for photo), formation of Tramway's Sporting Associations, retirement of Board's driver Peter Savage, bus driving school transferred to Hawthorn, Apprentices and Profile on Bill Sibbison, Depot Manager North Fitzroy. .6 - Spring 1981 - 8 pages - Making of Squizzy Taylor film - Flinders St station, Engineering Amenities at South Melbourne opened, traverser at Preston Workshops, track work - pressing curves at South Melbourne, Conductresses re-union, model tramway at the Royal Show, retirements, sporting association, tramway band, AVM, reducing noise levels, lists Editorial committee. .7 - Summer 1982 - 8 pages - Its Christmas Party time, want to charter a tram or bus?, portable radios, MMTB role in Paraplegic Games, MMTB Architect Gene Marshall retires, photo of WW2 most popular conductresses ball, MMTB Highlights, O-Bahn. Has a profile on Rob Downing - Deputy Chairman. Also Dick Newnham - lift operator at head office, Bob Moffatt - driver turned actor. Also has a follow up on the making of the Squizzy Taylor film "What's wrong with Squizzy" and a photo of the Editorial team and their names. .8 - Autumn 1982 - 8 pages - item on "Taking Melbourne by Storm", photo of Austerity bus 500, Radio Centre, Clifton Pugh tram 504, Essendon Depot (see Reg Item 1005) includes of photos of managers, revenue etc, story on the most popular conductress photo by Win Gibson (see Reg item 180 and 181), new apprentices, John Murdoch model train (Diamond Valley) builder, Sunday vintage tram service (V214) and L class to the zoo. Has a profile on Mr. Peter Saul, Architect. (two copies held) (see image 1178i5 for cover) .9 - Winter 1982 - 8 pages - changes to Doncaster bus - Eastern Free extension, changes to Ministry will affect Board - Steve Crabb, new uniforms, Footscray Depot, apprentice awards, follow up on Austerity buses, Norm Cross and Destination City, Profile on Alan Nolan Runningsheds Engineer, and Mike McLeod MMTB Photographer. (two copies held) .10 - Spring 1982 - book - see Melbourne by tram, Bundoora tramway work, new articulated vehicles (B class trams), Elizabeth St modal interchange shelter, Brunswick depot, demise of the F class bus (Mark VI), profile of Daryl Meade bus engineer, Joe Saccasan carpenter building branch and a list of Jargon. (two copies held).Demonstrates a MMTB employee newsletter, early 1980sMagazine, two colour printed on A2 sheet, folded to A3, "METRA News", published by the MMTB. Each issue unless noted otherwise four pages. Major items listed. Each issue has personnel news, including new staff, promotions, overseas items;trams, tramways, mmtb, z3 class, bourke st, track equipment, overhead, most popular conductress competition, hawthorn depot, clothing, trolley buses, fund raising, footscray, welfare, sale of trams, recovery, r10 vehicle, flinders st, films, radio centre, essendon depot, theatre, transporting art, austerity buses, footscray depot, doncaster, minister for transport, shelters, bundoora, brunswick depot, buses, mont albert, route 42