Silver coloured metal petrol iron with removable top plate and cylindrical tank. Metal handle with blue painted wooden top attached and metal plaque with maker's details and insignia between screws on bottom section of handle.Plaque shows: (on left hand side) "All British / PUMPLESS IRON / Manufactured by / HANDI WORKS / Brisbane" INSIGNIA / "H" / in shield. (on right side) P/No. ? / D/S No. ? / Reg No. ? / FOR BEST RESULTS USE SHELLITEclothes iron, petrol

Coleman 4A Instant Lighting Irons were made between 1929 and 1948. This brochure with its operating directions and service instructions would assist the user to repair their Coleman iron themselves. Petrol irons were useful in areas like Emerald without reliable electricity. Overheating, spillage, toxic exhaust gases and (sometimes) explosions were all possibilities to be avoided through careful monitoring by the user.This brochure accompanied a type of iron in use in Emerald before the advent of reliable electricity. Trifold brochure with service information and operating directions for a Coleman Iron. Trifold opens out to show operating instructions and service notes in French and Spanishpetrol iron, coleman 4a, emerald

Silver coloured metal petrol iron with removable top plate and cylindrical tank. Metal handle with blue painted wooden top attached and metal plaque with maker's details and insignia between screws on bottom section of handle. Plastic knob to remove top section. Pumpless Iron, with Wooden Handle and Attached Canister for Shellite (lighter Fuel).Metal Plaque on the left side says "All British Pumpless Iron. Manufactured by Handiworks Brisbane" Other writing in the metal is not legible. the letter "H" has been engraved into the top of the iron under the handle. "CLOSE HANDI" with an arrow pointing right on the black plastic knob on top of the iron and the back of the iron.clothes iron

Silver iron on stand with black handle and knobs. Cylindrical tank at back. Original cardboard box contains: instruction sheet, small carton containing spare part, spanner and spare knob.On box: Handi British Self Heating Pumpless Iron.|On instruction sheet: Directions for operating the improved Handi pumpless iron, 3 pages of detailed instructionsdomestic items, irons

Petrol irons were introduced in 1902.Chrome pumpless petrol iron with blue wooden handle,"All British Pumpless Iron / Handi Works Brisbane / Handi Hall Mark Product."irons, laundry irons

The beginning of standardised weights and measures began In Victoria when the Melbourne Observatory received sets of standard weights and measures, which had been tested in Britain against the then British Imperial standards. These included the primary standard yard and pound for the Colony of Victoria. Other standards of weights and measure held by shires and the administrative body's within the colony could then be compared to these primary standards. A Weights and Measures Act was passed in Victoria in 1862, establishing local inspectors throughout the colony. By the 1870s each local council and shire in Victoria held a set of standards that were used to test scales, weights and dry measures used by wholesalers, factories and shops. Every ten years the councils’ standards would themselves need to be rechecked against the Victorian Standards. The checking was done by the Victorian Customs Department in the 19th century, but with the transfer of responsibility for customs to the Federal Government in 1901, weights and measures function was retained by the Victorian Government and was shifted to the Melbourne Observatory. In 1904, a new building was erected at the south end of the Great Melbourne Telescope House, where the standard weights and measures and testing equipment was installed. This room had a large whirling apparatus for testing air meters and became known as the Whirling Room. When the Melbourne Observatory closed in 1944, the Weights and Measures Branch was formed to continue and this branch remained at the Observatory site unit until 1995. An example of a galvanised measuring jug made specifically to maintain government standard liquid measurements that were sold to the public. The probability is that this artifact was made around the first quarter of the 20th century and gives us today a snapshot of how imperial weights and measures were used before decimalisation and how a standard of measurement for merchants was developed in Australian based on the Imperial British measurement system. The container has social significance as an item used in Victoria as a legal standard measure to ensure that goods sold in Victoria were correct given the item is galvanised it was probability used for kerosene or petrol etc not for liquids used for human consumption. Galvanised Iron jug with rounded top, Inscription on handle at back. 2 gallon GV.35flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Used by the donor Gwen Asling (nee A'Vard) when she lived on her parent's (George and May A'Vard) dairy farm in 1920.The A'Vard family were pioneers who came to selected land in The Dandenong Ranges in 1898 Green enamel body, iron bottom, 2 control knobs, black wooden handle and petrol can attached Peerman pumpless, serial number PL/46 domestic appliance, laundry

Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. Late in the 19thC designers experimented with heat retaining fillings for these irons. William Coleman began selling Kerosene lanterns in 1900 in Kingfisher, Oklahoma, USA. He moved to Wichita, Kansas in 1902 and the company became world wide. The company also produced a range of cooking stoves and domestic irons. This spirit- fuelled flat iron was very popular in 1920s - 30s These sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire The family of Miss M Curtis were early settlers in Moorabbin ShireA) spirit- fuelled, sad iron with chrome plated sole c1920, and metal trivet The iron is blue enamel with a white speckled body, with a hemispherical tank for the Coleman 'Lighting Petrol' that provided the heat for smoothing the material B) Coleman Fuel measuring can and funnellMetal Trivet/stand " COLEMAN" ; Petrol can " COLEMAN" / MEASURING CAN / for INSTANT LIGHTING IRON/ with printed instructionssad iron, kitchen equipment, coleman william, kansas, oklahoma, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh, fireplaces, stoves, petrol fuelled irons, spirit flat irons, coleman lamp stove co. ltd.

For pumping air into petrol irons, the maker is probably Coleman. Liquid fuel irons were a great advancement from Sad Irons in the late 1800's and were used before electricity was availableBrass air pump with wooden handle. A brass tube two centimetres diameter and 14 ccentimetres long with a half centimetre diameter. A 14 centimetre long metal rod with a two and a half centimetre diameter and a three and a half centimetre long wooden handle which slides in and out of the tube. Presumably there is a fitting inside the tube on the end of the rod to push air out of the hole on the other end of the tube.K15.3coleman iron, brass air pump

The Lister Auto-Truck was a small monowheel tractor built for moving light loads around factories, railway yards and similar sites. They were built by R A Lister and Company of Dursley, Gloucestershire, well known for their range of small stationary engines The Auto-Truck was one of several monowheel tractors to appear in the 1920s and '30s, with the availability of small, reliable petrol engines, as developed for motorcycles and the stationary engines for which Lister were already known. These were tricycle vehicles, with the single leading wheel used for both drive and steering. Their simple construction carried most of the mechanism on this wheel as a single unit, the chassis with the trailing wheels being little more than a trailer for balance. Simplicity was a key feature. The engines were single-cylinder and air-cooled. Ignition was by magneto, rather than requiring a battery and electrical system. One of these designs was produced in the 1920s by George Grist of the Auto Mower Co., Norton St Philip, Somerset. The engine was a JAP 600 cc four-stroke air-cooled sidevalve, a typical small engine of the time. The Auto Mower Co. were Lister agents and when Lister heard of this 'Auto-Truck' they bought one for use in their own factory. It was used to carry heavy engine castings from the foundry to the machine shop. Lister customers saw them and there was such interest in wanting to buy them that Lister negotiated with Auto Mower to build them under licence. Although Lister were already well known for their small petrol stationary engines, these were heavy cast-iron engines with water hopper cooling and unsuitable for vehicle use. Lister remained with the JAP engine for the Auto-Truck. The Auto-Truck was designed for use in factories or other places with smooth surfaces of concrete or tarmac. This allowed the use of small solid-tyred wheels with only simple suspension, making the vehicle simple, cheap and lightweight. They had little ability on soft surfaces though and could even topple over if driven carelessly across slopes. Their design was a compromise between the top-heavy nature of the tall engine grouping above its wheel and a well thought-out chassis for stability. The bearing between them was a large diameter ring roller bearing, mounted at the lowest part of the chassis. This gave rigidity and stability, even after long wear. A ring of rolled channel girder was attached to the engine group and rollers on the chassis carried the load upon this. On early Auto-Trucks this bearing is set very low, in line with the chassis members, and is covered by thin steel plates. The front panel of the engine cover is distinctive with large ventilation holes and a Lister signature cut through it. Strangely this panel is made of thick cast iron, providing substantial weight high on the engine and only adding to its top heaviness. To improve visibility of moving vehicles in noisy factories, this panel was often painted white, the rest of the vehicle being Lister's usual brunswick green. The driver was seated on a Brooks bicycle saddle, which in recognition of the lack of vehicle suspension, was carried on the end of a cantilevered bar that acted as a leaf spring. A wide handlebar on the engine group was used for steering. A squeeze bar the width of this handlebar engaged the clutch. Controls included a hand throttle, a gear lever with two forward and one reverse gears, and a large handbrake lever. The engine unit rotated freely for a full 360° rotation. When used in reverse, the Auto-Truck could either be driven from the saddle, looking backwards over the driver's shoulder; or they could dismount, swivel the engine unit around and control it as a pedestrian-controlled truck from behind. Under the engine cover were two equal diameter tanks, a fuel tank for petrol and a shorter oil tank. Engine and chain-drive lubrication used a total-loss oil system, controlled by a small pump and needle valve. Info Ref: Lister Auto-Truck - Wikipedia https://en.wikipedia.org/wiki/Lister_Auto-TruckHistoric - Industrial monowheel tractor for moving light loads around factories, railway yards and similar sites.The Lister Auto-Truck - small monowheel tractor Made of steel with three wheels. Powered by a J.A.P single cylinder petrol motor which is Hand Cranked to start.Lister puffing billy, lister, lister auto truck, monowheel tractor

Rail tractors were popular with Victorian sawmillers. They were generally cheaper than a steam locomotive, required no special qualifications to drive, and used proven power plants for which spares were available locally. The tractor was constructed by Day’s Engineering of South Melbourne which, although better known for its pumping equipment, built more than fifty rail tractors for Victorian sawmillers and other industrial tramway users. W. Day & Sons is believed to have constructed its first light railway locomotive in 1926. From then until the mid 1940s, the firm appears to have built at least fifty locomotives at its premises in South Melbourne, of which roughly half were four-wheel locomotives and roughly half were six-wheel locomotives like the restored Day’s rail tractor formerly operated by Ruoak Timbers. Of the four-wheel locomotives, ten were 2-ft (610mm) gauge locomotives similar to this one. Today, only two survive, a complete example at the Puffing Billy Railway Museum at Menzies Creek, and one at Alexandra Timber Tramway Museum This 2-ft gauge 4wPM locomotive is believed to have been one of two Day's Petrol Rail tractors formerly used by Cheetham Salt, possibly at the Moolap works near Geelong. Service History :owned by Cheetham Salt, Moolap ( dates unknown ) Geelong Steam Preservation Society , Belmont 1973 ? Puffing Billy Steam Museum , Menzies Creek Historic - Industrial Narrow gauge Railway - Rail Tractor used by Cheetham Salt Company works at Laverton, Moolap and Geelong, Victoria , Australia Petrol Rail Tractor made of Iron , wrought iron, steel puffing billy, industrial narrow gauge railway, rail tractor, days engineering, cheetham salt,, petrol rail tractor

Malcolm Moore No. 1013 Four wheel Diesel Rail Tractor Gauge 2'0" Malcolm Moore rail tractor (Builder’s Number 1013) It was built for the Australian Army in 1943. It was sold to the Inkerman Sugar Mill in Queensland around 1948 for hauling cane and shunting at the works. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It was purchased from the Inkerman Mill of Pioneer Sugar Mills in 1982. Historic - Industrial narrow gauge Railway - Diesel Rail Tractor - used by the Australian Army and Inkerman Sugar Mill in QueenslandDiesel Rail Tractor made of iron and wrought irondiesel rail tractor, puffing billy, inkerman mill, industrial narrow gauge railway, gauge 2’0”, inkerman sugar mill, australian army

Robert Charlton conducted a blacksmith, wheelwright and farrier business on the corner of Evans and Station Street, Sunbury from 1918 to 1940. The copy was taken from a photograph displayed in Mick Walsh's garage which is now on the above site.A black and white photograph of two sheds. A weatherboard shed with corrugated iron roof is on the LHS and the corrugated iron building is the blacksmith's forge and wheelwright's workshop. Two men are standing in fron of the large doorway. An advertisement for Dr. Morse's Indian Root Pills is written across the roof and 'BLACKSMITH' is painted on the wall.blacksmiths, wheelwrights, coach builders, advertising, charlton, robert w., walsh, mick, petrol station, station street, evans street, sunbury, george evans collection

Single cylinder horizontal petrol engine mounted on a 4 wheeled trolley. Two flywheels, one either side, no pulley. Galvanised cylindrical fuel tank mounted on a wooden box in front. Box contains a battery and ignition coil. Trolley has cast iron wheels and is designed for pulling by hand. Painted red and grey. Probably a power source for farm machinery. On a brass plate fixed to the cylinder. "Waterloo Boy Gasoline Engine / No. 81491, HP 4 / Waterloo Gasoline Engine Co. / Waterloo Iowa / Patented / August 7 1900, Dec 3 1901, Oct 7 1907 / Other patents pending / Sold by Waterloo Gasoline Engine Co." On each side of the water tank is an oval white transfer with "Waterloo Boy" above an illustration of a small boy wearing a wide brimmed hat.machinery ... engine ... petrol ... metalwork

This building was constructed at Old Gippstown from materials at hand. It was named after the garage operated in Maffra by W.O. (Bill) Fulton, blacksmith, garage proprietor and later state member of parliament. A large rectangular-shaped corrugated iron shed, used as a Garage. It has a gabled roof made of corrugated iron. There is a billboard on the front of building's roof.motor garage, old gippstown, west gippsland, gippsland, gippsland heritage park, goldfields, coal mine, victorian era, moe, historical village, petrol station, w.o. (bill) fulton, old gippstown heritage park, latrobe valley, buick hearse, chevrolet tourer, hudson hearse, stanley steamer, plume texaco, shell, cor, petrol pump

The garage was established in the 1930s by Mr Gamble. Other proprietors were Perc Kimberley 1943-46, Henderson 1946, Neil Rogers. K. & B. Patton ran the garage from 1960s - 2008Colour photo of K. & B. Patton's Garage. The garage is a white, weatherboard single story building with a corrugated iron roof. There small lean-to on the LH side of the building. There is a large entrance and two large windows on the front. There are two petrol pumps at the front of the building. A blue car and a white utility are parked at the LH side of the garage. The signage on the front of the building reads K. & B. PATTON NISSAN and there is a NISSAN sign painted on the roof. There is a sign for Peter Stuyvesant cigarettes on the roof of the lean-to. A telegraph pole and the entrance to Gordon Park is on the right of the photo.perc kimberley, k & b patton, gamble, henderson, neil rogers, business, industry