KBW Slotting MachineHistoric - Industrial - Slotting MachineLarge metal KBW Slotting Machine KBWbelt driven, puffing billy, slotter, kbw, slotting machine

Although it’s unknown when these two photos were taken, the South African Pattern Mk IV Slotted Template Machine was in service from 1936 to 1952. The machine was used to cut slots and holes in an acetate film medium. This template was then used to fit several runs of aerial photography to ground control points at a desired scale with a substitution of the templates in the assembly. Radial slots on the templates from central holes representing the photograph’s principal point (centre) were placed over hollow metal studs mounted over control points on the scaled base sheet. The studs represented the intersection of radial lines through common points of detail of overlapping photos. A pricker was used to transfer from the photo-points to the templates. The slotted template methodology was later used as an essential aero-triangulation exercise in advance courses conducted at the School of Military Survey.These three photographs are of a slotted template machine used in aero-triangulation. The first two photographs were printed on photographic paper and are part of the Army Survey Regiment’s Collection. The photographs were scanned at 300 dpi. The third photograph was captured from a collection using a smart phone. .1) and .2) - Photo, black & white, 1936-1952. South African Pattern Mk IV Slotted Template Machine. .3) - Photo, black & white, 1936-1952. WO2 Bob Pratt operating the Slotted Template Machine. .1 and .2 –annotated on back “Slotted Template” .3P - annotated on front “COMPILATION SECTION SLOTTED TEMPLATE MACHINE WO2 BOB PRATT”royal australian survey corps, rasvy, army survey regiment, army svy regt, fortuna, asr, air survey, aerotrig

A time clock, sometimes known as a clock card machine, punch clock, or time recorder, is a device that recorded the time an employee entered and left the factory. In mechanical time clocks, this was accomplished by inserting a heavy paper card, called a time card, into a slot on the time clock. When the time card hit a contact at the rear of the slot, the machine would print day and time information (a timestamp) on the card. One or more time cards could serve as a timesheet or provide the data to fill one. This allowed a timekeeper to have an official record of the hours an employee worked to calculate the pay owed an employee.Metal time card rack.time card, rack, employee, factory, timesheet, data, mechanical, punch clock

A time clock, sometimes known as a clock card machine, punch clock, or time recorder, is a device that recorded the time an employee entered and left the factory. In mechanical time clocks, this was accomplished by inserting a heavy paper card, called a time card, into a slot on the time clock. When the time card hit a contact at the rear of the slot, the machine would print day and time information (a timestamp) on the card. One or more time cards could serve as a time sheet or provide the data to fill one. This allowed a timekeeper to have an official record of the hours an employee worked to calculate the pay owed an employee.Metal time card rack.time sheet, time card, factory, employee, work life, punch clock, textile industry

This ornate, Victorian-era automatic weighing machine was made in England around 1884-1909, by George Salter and Co. of West Bromwich, UK, makers of scales since 1760. It is protected by Queen Victoria’s Royal Letters Patent, signed in 1900. The scale stood outside the Warrnambool Post Office in Timor Street from around 1909 to 1966, as shown on postcards and photographs held at the State Library of Victoria. The scale is identified by the Serial Number '665', and was installed by the distributors, the Australasian Automatic Weighing Machine Co. Ltd.. The scale’s weight measurements were in Imperial stones and pounds up to 20 stone (127 kg). The scale’s face included charts of average weights, for men, women, boys and girls, by various heights, in feet and inches. The coin slot and its face were converted to metric measurements by the Eastern Scale Company Pty. Ltd; that firm was registered on October 2, 1974. The Australasian Automatic Weighing Machine Co. Ltd was a large supplier of weighing scales in Australia and held the Royal Letters patent for their machines, distributing them in prominent locations. In 1902, the firm was listed under the Import Entries Passed at His Majesty’s Customs, importing into Sydney, NSW, eight cases of scales. In 1911, the company asked permission from the Port Pirie Corporation to install a machine in Alexander Street. In 1913, the company applied to the City of Sydney to install machines around the city, including at the tram depot. One application mentions “… three machines in three places for three pounds per year”. In 1923, the firm tendered for the right to place Automatic Weighing Machines on railway and tram premises throughout New South Wales, subsequently for five-year terms, in return for a fixed payment per machine and a portion of the revenue to the NSW Government. In 1928, the Sydney Harbour Trust gave the firm the right to place the weighing machines on various ferry jetties. The firm was still operating in 1941, advertising for two boys aged 14-16 for the workshop and messages, at the Rialto building, 497 Collins St., Melbourne. On December 21, 1946, the Commonwealth government invited offers to tender for the right to place automatic weighing machines on postal premises throughout the six states; the successful company then made arrangements with the federal Postmaster General's Department to place machines outside post offices across the country. A few years later, on September 11, 1950, the firm's Adelaide branch ceased trading. From 11th July 1950, the Australian and Eastern Engineering Company Pty. Ltd took over at the same premises, at 179 Pirie Street, Adelaide. The Perth branch ceased business in WA on July 6th, 1950. Percival Everitt invented and patented the automatic, coin-operated personal scale design. Everitt was a Norfolk-born engineer and regarded as the father of the coin-operated industry. As a young man in 1877, he invented a hay and corn pitcher, a turnip thinner in 1878 and an Automatic Travelling Anchor in 1880. But his fame came in 1883 with the first postcard-vending machine, over a hundred of which he distributed around London. In 1884, he patented one of his many inventions, the coin-operated scales for use in public places; for many people, it was their first exposure to coin-operated machines. His success prompted the formation of the Weighing Machine Company in 1885. Further inventions followed: a blow tester in 1887, the machine for testing a person's grip in 1888, and in 1889, the dispensing machine for hiring out opera glasses, and a device for shutting down the coin entry slot if the machine was empty. In 1890, he invented a fortune-telling machine. Everitt sadly did not make his fortune; he died suddenly in February 1893, in his late forties, with £71 to his name. George Salter & Co., West Bromwich, England, produced automatic weighing scale machines from Everitt’s patented design, and advertised them as suitable for hotels, pleasure gardens, theatres, exhibition halls, clubs, baths and places of public resort. The company was established in 1760 by brothers Richard and William Salter, and manufactured springs and pocket steelyards (spring balances). After several generations, the company was taken over in 1855 by a nephew, George, and renamed George Salter & Co. In 1884, Salter registered the trademark of a Staffordshire knot pierced by an arrow. The company's expanded range of products included the first coin-operated public weighing machines in the 1880s and, in 1895, the first English-made typewriter. In 1915, Salter became a limited company, Geo. Salter & Co. Ltd. When the last George Salter died in 1917, the company passed into the hands of other relatives, but continued to grow before being bought out by Staveley Industries in 1973. Despite several subsequent mergers, the Salter name continues to be seen on household products such as digital scales. This patented, coin-operated weight machine is significant for its association with Percival Everitt, the inventor of the world’s first slot machine, with the renowned maker of scales, G. Salter & Co., which began operating in 1760, and also with the Australasian Automatic Weighing Scale Co., which imported and widely distributed the scales throughout Australia from the early-to-mid 20th century. It is a rare example of an early vending machine used in public places from the late 19th through to the mid-20th century. These machines were the early step in the evolution of coin-in-the-slot machines, which are still used today. The scales give a glimpse into our history; they became quickly popular with the public, which, until then, had little access to weight scales apart from those at medical services. They also provided inexpensive entertainment for families, especially while waiting for trains or visiting the post office. The machines were also attractive and lucrative to the distributors; once installed, they required very little maintenance, and their low cost to customers kept the money coming in. This automatic weighing machine is also significant for its decades of service to the local and regional community of Warrnambool, for personal and commercial purposes. A public coin-operated weighing scale, also called a penny scale. It is a large, silver-painted cast metal stand with a square top on a pedestal that flares outwards to join a rectangular platform base with posts on the side and corners that may have had fitted wheels. The round, white face on top has red and black measurements and inscriptions. A slim indicator with a point at one end and an arc at the other is attached to the face’s centre. The coin slot is above the face, on the left, and the scale’s identification number is engraved on an oval plate on the right. Moulded motifs decorate the pedestal’s front and are repeated on its sides; they depict a tall, narrow urn with a bowl on top and fancy scrolls on either side. There is a decorative panel across the front top of the stand. The top of the pedestal has a small keyhole. The size of the coin slot fitted a penny coin, and the weight measurements on the face were in Imperial stones and pounds. Quite some time after 1966, when Australia introduced new decimal weights, measurements and currency, the scale was updated; the coin slot size was changed, and a new face with metric measurements was installed. The scale now accepts a $1 coin (one dollar) and the scale measures weight in kilograms and grams, from 0 to 125 kg.. The rear of the scale has a small, rectangular metal plate with printed text. The scale was made by G Salter & Co. of West Bromwich, UK, distributed by the Australasian Automatic Weighing Platform Co., and updated to metric measurements by Eastern Scale Co. Pty Ltd. It was previously installed at the Warrnambool Post Office. Engraved on an oval plate on the right: "665" Top centre of the face, in red: "$1 coin" Top of face: "EASTERN SCALE CO. PTY LTD" Base of face, in red: "[Royal Coat of Arms of Britain]" with words, below in red: "BY ROYAL LETTERS PATENT" Around the face, in black: "[numbers 0 to 125, in increments 5, and makes between the numbers for each 500g]" "kg" Below the face, moulded letters within a shield: "AUSTRALASIAN AUTOMATIC WEIGHING MACHINES CO. LTD." At the back of the weighing platform: "G SALTER & CO. / WEST BROMWICH", remnants of logo “[Staffordshire knot pierced by an arrow]” Plate on rear: THIS SCALE REMAINS THE PROPERTY OF EASTERN SCALE CO. PTY. LTD., 8 GEORGE COURT, GREENSBOROUGH, VIC, 3088. PHONE (03 ) _ 34 _ _ 33” (434 9333 ?_flagstaff hill, warrnambool, maritime village, maritime museum, flagstaff hill maritime museum and village, shipwreck coast, great ocean road, scale, weighing scale, salter, australasian, 1 dollar, $1 coin, 1p, 1 penny coin, penny scale, coin in slot scale, eastern scale co. pty. ltd., british royal coat of arms, royal letters patent, letters patent, health, ending machine, coin-operated machine, percival everett, weighing machine co., george salter & co., g salter & co, west bromwich, vending machine, weights & balances, measurements, slot machine, coin operated machine, penny-in-the-slot, coin fed, coin op scale, weights & measures, australasian automatic weighing machine co. ltd., warrnambool post office, machine 665, no. 665, blalnce technology, scales and weights, weights and measures, penny weight scales, vintage, weighing machine, coin in the slot, coin operated, public scale, public weighing machine, penny-weighing machines, penny weighing machines, penny scales, coin operated weighing machine, scale weighing machine

Used to lay out Machine work, or to set up pieces on a planer, radial drill, milling machine or boring machine. To set the Scriber the spindle swivels down or up into any position where it is clamped by the knurled nut. There is a fine screw adjustment for the Scriber point (note: this is not original Scriber supplied with this instrument). The base on this Surface Gauge can be set on cylindrical work, using the ‘V’ groove in the base, or by pushing down the two gauge pins. It can be brought square with an edge or T slot. Metal gauge toolgauge, tool, trade, brown and sharp manufacturing company

This testing voltmeter recorder was last certified by SEC Vic laboratories on the 17/4/77. It was used extensively as mobile recorder placed for periods of one month at locations experiencing unacceptable fluctuations of power. These locations would cover the North East regions of Victoria. They cover voltage drops at domestic and business properties especially those that were experiencing regular fluctuations(daily) at approximately the same time of the day. As the electrical network is required to operate within a set level of voltage, fluctuations outside of this has to be investigated and necessary remedial action taken. This is especially so for rural properties where power "drainage" can occur through animal/bird and tree interference. It can also be the result of defective wiring and overloading at peek operational times (milking machines).This mobile voltage recorder is very significant to the Kiewa Valley because it highlights the difficulties that can occur in maintaining a power supply that experiences fluctuating power demands by the rural industries that it supplies. The requirement of a mobile testing apparatus to cover the various sections in the Kiewa Valley and other rural areas in the northeast region is one of necessity as electricity once connected to a rural property is a labour saving supply as generators on rural properties require a higher degree of maintenance an ultimately at a higher cost. The testing of the SEC Vic supplied electricity to rural properties,those who had previously run on generators, had to be quick and unassuming with certainty of correct supply levels.The mechanism of this voltage recorder has been installed(by the manufacturer) into its own protective wooden box. This box has a front (swing open) lockable section which permits direct access to the installed measuring equipment (for servicing and data collection). The top section of the box has two screw on terminals for access to the machine being tested. This tester has its own inbuilt ink supply facilities and a mechanical clockwork device that unwinds a roll of paper onto a second roll at a rate of 10 mm per hour. The recording chart is marked with time slots against voltage. There is a recording arm which has an ink pen at the end. Both arm and pen carry the ink supply from the ink reservoir, located on the left side of the cabinet door in specially constructed bottle holder( three small bottle capacity). To record a suspect power problem to a home or business establishment the voltmeter is connected to a power supply outlet being tested and wind the recording clockwork mechanism (gives a four week running time). Before leaving the recorder in situ the electrician checks to see if the chart is recording the correct voltage and that the clock mechanism is advancing correctly.On the front of the access "door" at the top a metal label "RECORDING AMMETER" below this "MURDAY SYSTEM" below this "ALTERNATING CURRENT" and below this the manufacturer's registered number "No. 139156" Below this is a metal tag with State Electricity Commission of Victoria Electrical Engineer's Section equipment number "338" Below these tags and above the viewing window is the manufacturer's dtails "EVERSHED & VIGNOLES Led LONDON"sec vic kiewa hydro scheme, alternate energy supplies, alpine feasibility studies temperature, rainfall, power outages

Standard woollen army jumper as issued to Australian servicemen during the conflict in Vietnam. This item belonged to National Serviceman David G Woods, No:2783285, who served in 7RAR in 1967.Khaki army V neck long sleeved woollen jumper, 1968 Size 38. Provision on both shoulders for badges with epaulette slots.On label: Jantzen NSW 1968/Size 38, 8405-66-024-7645 Machine washable woods, army, vietnam, sweater, pullover, jumper, 2783285

The phonograph is a mechanical device for the recording and reproduction of sound and originally used a tinfoil sheet wrapped around a rotating cylinder to produce the sound. It was invented by Thomas Edison of U.S.A. in 1877 and was the model for all phonographs or gramophones made and developed throughout the 20th century. This machine is of particular interest to the Warrnambool and District Historical Society as it is an Edison phonograph and an earlier model of this phonograph was used in Warrnambool late in the 19th century to make an important recording. In 1896 Thomas Rome, an employee in a Warrnambool boot and shoe shop, purchased an Edison phonograph that could both play and record sounds. At the Warrnambool Industrial and Art Exhibition of 1896-7 visitors to the Exhibition paid a fee to listen to music on this phonograph. But Rome also recorded some local Warrnambool people singing and speaking and these recordings survive today. They are regarded as the oldest surviving recordings made in Australia. Thomas Rome later became a shoe shop proprietor in Warrnambool and was a well-known person in the town/city for a great number of years. This is an Edison Gem Phonograph. It has a black-painted wooden base, now detached from the main mechanism. The phonograph is made of metal which is now heavily rusted. It has a cylindrical turntable for playing the Edison cylindrical records and a handle with a wooden knob. The turning mechanism and belt are now broken. The name of the manufacturer and details of the patents are on a metal plate attached to the side of the phonograph. The amplifier mechanism at the top of the machine is missing. The cover of the machine is made of wood and has a wooden handle attached with a piece of metal and two metal screws. There are also two metal screws on the side of the cover. The cover has a slot on the side to allow the turning handle to be accommodated outside of the cover. The cover is much stained and spotted. ‘Edison Gem Phonograph’ thomas edison, history of sound recordings, thomas rome (warrnambool)

This 20th century business machine was used by the firm of D.H.Wood Motors of 169 Koroit Street Warrnambool. This firm advertised that it sold mainly Peugeot and Studebaker cars and Hillman and Humber cars and commercial trucks. This machine has local provenance as it came from the 20th century business of D.H.Wood Motors. It also has some historical interest as an example of a business or office machine used in the early to mid 20th century before the general use of computers. This is a grey rectangular-shaped metal box with rounded edges. The box has four metal studs on the base to keep the box stable. The box has a hinged section for the insertion of the paper dockets and a turning mechanism for removing the dockets, one at a time from a slot at the top of the machine. The dockets have a white (customer's) copy and a pink duplicate copy for the business to file. Two of the dockets have been removed from the machine to show the contents. The number of dockets in the machine is unknown. The metal surface of the machine is rubbed and rusty and the paper is stained. 'Paragon' 'D.H.Wood Motors, 169 Koroit Street, Warrnambool' 'Lamson Paragon Limited Wiz Register' vintage business machines, warrnambool

These metal time card racks were used at Foster Valley Mill, Geelong. Three metal racks with numbered cream cards and slots. Front: [embossed] IBMvalley worsted mill, foster valley mills, geelong, working life, time card racks, international business machines corporation, ibm, textile industry

Australia Post Wall mounted postage stamp vending machine used to dispense stamps.Metal postage stamp vending machine. Wall Mounted. Embossed letters POSTAGE STAMPS on front. Horizontal slots for coins have been covered with plates stating NOT IN USE and OUT OF SERVICE. White metal plate with the wording STAMPS 5 CENTS. Two Key holes. Recepticle for the dispensing of stamps with a lift up lid with Embossed words LIFT. Postage Stamps; lift; post, stamps, vending machine, australia post offices, postage stamps, tatura

Bodice of a blue linen dress made by Elfriede Girschik for her daughter, Helga, in Camp 3. c1942 (early). The singer sewing machine it was made on came with her into the Camps.Blue linen bodice which has been part of a dress. The bodice has sleeves gathered at the top and slots for elastic (not there) at the lower edge. 6 handmade buttonholes down the opening at the back with 6 small buttons. Hand embroidery on the front, 2 ladybirds, sprays of yellow, blue, pink and orange flowers. The bodice has been separated from the bottom of the dress and hemmed up to make into a top.bodice, embroidery, camp 3, tatura, ww2 camp 3, internment camp handwork, helga griffin, helga girschik

Flanged Tramway Rails - sections from The North Eastern Steel Co. Ltd. Middlesborough - see https://www.gracesguide.co.uk/North_Eastern_Steel_Co 1 - Walthamstow & District Light Railways BS Section No. 3C - 106 lbs. per yard 1904 - Dick Kerr & Co. Contractors London. See https://en.wikipedia.org/wiki/Tottenham_Outrage 2 - Bath & District Tramways 95 lbs per yard 1903 - George Hopkins & Sons Engineers London 3 - Burton on Trent Tramways 90 lbs per yard 1903 - Messrs Kincaid, Waller & Manville, Consulting Engineers 4 - Swindon Corporation Tramways BS Section No. 4 C, 111 lbs per yard, 1904 - Messrs J G White & Co. Ltd, Contractors London 5 - Wigan Corporation Tramways BS Section No. 5, 100 lbs per yard, 1903 - Messrs J G White & Co. Ltd, Contractors London 6 - Derby Corporation Tramways BS Section No. 6, 107 lbs per yard, 1904 - Messrs J G White & Co. Ltd, Contractors London 7 - Nottingham Corporation Tramways BS Section No. 1 , 90 lbs per yard, 1903, J. G. White Ltd, London, Contractors. 8 - Swindon Corporation Tramways, BS Section No. 4, 105 lbs per yard - Messrs J G White & Co. Ltd, Contractors London, Messrs Lacy & Sillars Consulting Engineer 9 - Kalgoorlie Electric Tramways BS Section ? 96 lbs per yard. 1904 - Messrs J G White & Co. Ltd, Contractors London 10 - Leicester Corporation Tramways & Track? 100 lbs per yard 1903, I George Maybey? MICE Engineer 11 - Ipswich Tramways 90 lbs per yard, 1902, Dick Kerr & Co. Contractors London Shows the type of tramway rail and cross section produced by The North Eastern Steel Co early 1900's, the relationship to the British Standard and who used them. Provenance of the item not fully known. Possibly given to the Electric Supply Co of Victoria at the time when they would have been ordering rails for use in Ballarat. May have been collected by other parties.Plywood sheet, covered in black cloth displaying 11 different British Standard Rail Sections made by The North Eastern Steel Co. Ltd. Middlesborough , early 1900's. Each section secured with two 20mm (¾”) long, 3mm dia (1/8”) machine screws, countersunk with a slotted head from the rear. All nickel plated on both sides, engraved as to the tramway used on, date of production on the head of the rail, Designing Engineers on the web and the manufacturer on the foot of the rail. Cloth secured with staples and drawing pins on the rear. On the rear is a chalked sign, the principal one being "No Thoroughfare"Engraved as listed.tramway rails, rails, tramways, north eastern steel co, middlesborough, walthamstow, bath, burton on trent, swindon, wigan, derby, nottingham, kalgoorlie, leichester, ipswich, j g white & co, dick kerr

A cartoon of the 1930s titled "The Clancy Kids" of a boy dropping his pennies down the cable tram slot. Calls on Mr Timmie to help who responds with a comment regarding a vending machine. If you dropped a coin or a small item down the slot, there was no way of retrieving it.Demonstrates the peril of cable tram slots and lost items. Reproduction of a cartoon onto a display paper.tramways, cable trams, cartoon, cable slot, pennies

This attachment was used by donor . It was a great improvement over hand made buttonholes.A Singer buttonhole attachment used about 1950s. It was attached to ordinary power sewing machines to make button holes. It includes a small metal plate to cover teeth when making button hole and a fairly long slotted screw for attaching plate.Singer 86662 completehandcrafts, equipment

Projector was used at Christ Church Anglican Church Mitcham (now All Saints Mitcham) for showing film strips to the congregation, Sunday School and youth groups.Early 'Shelton' film strip projector in a steel grey painted and hinged metal case with carrying handle. Projector has been finished in a 'hammered' meta paint with a large transformer as its base. It is a 240 volt projector. The film strip is manually rolled through the slots of the projector to show each frame separately. Project lens is adjustable for focus and it has a small angle of adjustment foe aligning the image on the screen.Shelton Projector Made in Australiaphotography, projectors

An antique machine made forged steel pulley block with a hook at the top which moves sideways. It has a slot on the cylindrical section for the rope or chain. It is an old farm tool from the 19th or 20th century.MAKERS PATENT SNATCHpulleys, tools, lifting equipment, pulley blocks, steel

J. Mann and Sons was first established as a farm produce store in 1921. The range of products was extended in the 1930s and included groceries and hardware, as well as the first petrol bowser in Wodonga outside the store. After WWII, the premises were extended and the range of products continued to increase. In the 1960s the Mann Family opened a new supermarket in Wodonga, in addition to the hardware business, providing steel, plumbing and industrial supplies, and they employed over 100 people at one stage. With changes in the retail industry, the Mann Family sold the main hardware business to Bunnings and the steel and rural produce business to the Kelly brothers in 2006. Paragon, trading at various times as Lancom Paragon, Moore Paragon, Paragon Printing and the South Pacific Print Group, was also based in Wodonga from 1958 until 2010. It began as Lamson Paragon in 1958 but was destroyed by a fire causing £150,000 damage. The factory resumed operations on 24 June 1959.with 30 staff and by 1973 employed 120 and used 80 tons of paper per week. Further develp[ment took place to the factory in 2 stages. In 1977 Moore Corporation of Toronto took over control of the London based parent company Lamson Paragon necessitating a change of name of the Australian company to become Moore Business Systems Australia Limited. After many successful years of operation including expansion to a staff of 240 people, changes to business operations and the loss of several large contracts led to the company entering voluntary administration in March 2010.This machine and docket has local provenance as it came from the 20th century business of J. Mann & Son in Wodonga..The machine was manufactured by Paragon, also operating as Lamcon Paragon and Moore Paragon, which were a major manufacturer in Wodonga from 1958 until 2010.This is a grey rectangular-shaped metal box with rounded edges. The box has four metal studs on the base to keep the box stable. The box has a hinged section to enable paper dockets to be inserted. It also has a turning mechanism for removing the dockets, one at a time from a slot at the top of the machine. The machine includes a docket from Mann Mitre 10 Wodonga operated by J. Mann & Son Pty. Ltd. The dockets provided a duplicate copy for the company as well as the white copy for the customer. The dispenser and dockets were produced by Paragon.At top of dispenser: "Paragon" Across top of docket: "J. MANN & SON Pty. Ltd. (Incorporated in Victoria) TRADING AS: / Manns Mitre 10/ P.O. BOX 141, VIC., 3690. Phone: (060) 24 4813paragon, lamson paragon, moore paragon, mann wodonga, moore business systems australia limited

This Cash Register was used for the sale and production of lift tickets, lessons and packages during the 1990s at Falls Creek. The employees who operated the machine were called 'Ticket Tarts'. This item is significant because it was a critical part of the everyday operation of the chair lifts at Falls Creek.A large square cash and ticket machine with buttons and slots for the production of lift tickets. Long cable connected to the back. snow, ski season, ski pass, ski lessons, ticketing, sales

In the years of Allan Doney’s photography, landmark buildings succumbed to fire, neglect and redevelopment. He photographed the grey sand hills from Bendigo’s mining past, the streetscapes, poppet heads, miners’ cottages, gracious homes with ornate verandahs, trams and much more. Above all, his photographs show how much of the city has survived from the 19th century – and how much has not. Through two decades of great change, Allan Doney was there to capture ways people interacted with it. Although he travelled to many other places in Northern Victoria and beyond in search of subjects for his art, he seemed to always return to Bendigo for inspiration.

In the years of Allan Doney’s photography, landmark buildings succumbed to fire, neglect and redevelopment. He photographed the grey sand hills from Bendigo’s mining past, the streetscapes, poppet heads, miners’ cottages, gracious homes with ornate verandahs, trams and much more. Above all, his photographs show how much of the city has survived from the 19th century – and how much has not. Through two decades of great change, Allan Doney was there to capture ways people interacted with it. Although he travelled to many other places in Northern Victoria and beyond in search of subjects for his art, he seemed to always return to Bendigo for inspiration.

Close-up view of a Metcard public transport ticket vending machine with a coin slot, ticket dispenser, and multiple fare selection buttons for then three different zones and ticket types, including "Full Fare," "Concession Fare," "2 Hour," "City Saver," "Daily," "Seniors Daily," and various zone combinations. Based on the number in the near top left hand corner, possibly fitted to C class tram 3020. Photo by Morris Moller, Nov. 2006Yields information about the Metcard Ticket machines fitted to Melbourne trams. These were replaced by the Myki system.Colour print with a number on the rearIn ink on the rear "252/26"metcard, tickets

Ecru lace apron with floral pattern in border and edges. Fine ribbon (silk(?) tie through slot at top. Possibly Brussels machine made.embroidery, lace, aprons

Charcoal soft covered booklet with general notices, designs, andtrademarks. Patents include a portable washing machine, Kinematograph shutter, anti-splash valves, Railway collision preventing, telephone automatic coin slot patents, trademark