The specification produced by the Metropolitan Transit Authority (The Met) for manufacturing, supplying, and delivering electric trams. Has three options for delivery - 200 four-axle trams, 100 four-axle and 60 six-axle or 120 six-axle articulated trams. The last was selected. Tenders closed 27/4/1984. The donor used the book to superintend the contract by Comeng Dandenong. Has many notes for future engineering reference. See htd7741doc.pdf for source details.Demonstrates a specification document produced by the MTA for the B2 class trams.Bound specification approx 300 pages, with green cover and green comb binding. Has many loose sheets.Extensive notes throughout document for future issues, and current queries.tramways, tramcars, new tramcars, b2 class, comeng, tenders

Yields information about the work looking at increasing the load on pony wheels - not known whether done in practice.Set of two hand written notes. .1 - Set of calculations on the weight of an axle - if a different dimension to look at increasing the weight on a pony axle of a maximum traction tram. Written on the back of Tram Mileage Record Sheet form TYE 1.58 - daily record for each tram .2 - sketch of the finishing dimensions and dimensions of the end of an axle - written on the rear of a torn 1944 poster using for fund raising. Has the names of: T. A. Farr Hon President, A Purdue President and W. Sewell secretary for the "ACF" - Australian Comforts Fund.trams, tramways, axles, sketches, fund raising, maximum traction, forms, mileage

A cast iron wheel. The rim is ridged with fine teeth. In the centre is a fixed axle - bent and snapped off. It has six circular holes.wheel cast-iron machinery

20cm dia Cast Iron Trolley Wheel with 4 ribbed spokes. The rim of the wheel is slightly rounded. Axle hole is 2cm dia.

Drays were used to transport heavy materials such as farm products, building supplies, food. They were pulled by horses or bullocks. Drays were important for transportation in the Kiewa Valley.Made of timber and steel. The piece of wood contacts the axle hub to brake the dray. Part of a brake for a dray. It is missing the actuator that is needed for tightening the band to operate as a brake.drays, horses, bullocks

Used by Manning Chemist, Flinders Street Railway Station, Melbourne for folding individual powder portions into paper packages until 1984. Brass 'x' shaped folding frame with centre axle, ridges down one leg of stand with a pin on side of one top plate to adjust opening width.On top plate : British Made.

Set of three Preston Workshops reports for April 1963; 1 - Preston Workshops Tram Summary - week ending 20 April 1963 - detailing the tramcars awaiting attention, lifting shop, body shop, paint shop, trams receiving attention, trams received and trams dispatched with their work done. Lists tram that are held out of service, including those sold. Has ink notes regarding cracked axles. 2 - Sheet reporting on cracked axles supplied by Thompsons in 1923 and Hadfields 3 - Axle survey - 19-4-1963 - in workshops availed for processing of in use - lists by type of gear - BTH, GE, Metro Vickers and by axle status. Has ink notes along bottom edge.Yields information about Preston Workshops reporting, axles and general management.Set of 3 typed documents - foolscap sheets.tramcars, tramways, preston workshops, tramcar maintenance, axles

Memento or Pen and Ink stand featuring a model of the Peckham Pendulum axle box. Made from wood and brass with space for pens and ink bottles, titled "The Peckham truck and Engineering Company Ltd London". Features a model of the Peckham axle box with rotated within the frame. See https://www.tramwayinfo.com/Tramframe.htm?https://www.tramwayinfo.com/Models/Howto/Trucks.htm accessed 7/7/2020 for some details.trams, tramways, trucks, peckham, models, souvenirs

Pulleys date back to Ancient Egypt circa 1800BC. it is a simple machine used to lift weights.Used by residents of the Kiewa Valley.Steel pulley. A pulley is a wheel on an axle or shaft enabling a taut cable or belt passing over the wheel to move and change direction, or transfer power between itself and a shaft.pulley, pulley machine

Part of a larger piece of machinery used to crush clay. This part, the actual crusher, has a central axle from which radial bars to the outer surface, reinforces the crusher.ceramics, terracotta

Rusted wheel rims and axel were recovered from scrub near the ‘Eastern Landing’ in 2002. The two large wheel rims are made of flat iron. The axel is a long metal shaft with built up sections at either end. They are possibly from a WWI, horse drawn gun carriage used to carry stores from the jetty to the lightstation. Images show the carriage in use in 1943. The items have second level contributory significance for their historic value and provenance to the lightstation. .1 & .2, Large rusted, circular, metal wheel rims. Made of flat iron. .3, Rusted metal axle. long shaft with built up sections at either end.

Cart two wheeled 8 leafed sprung. Wheels have 14 spokes with steel axle. Tail gate with hooks. Ornate foot step. Two shalves. Keepers on shalves for breechen straps.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, cart

Set of three drawings related to the Brill 22E Maximum Traction trucks: 1 - "Brake Rigging Brill Maximum Traction Truct No. 22E" - showing the dimensions of the levers and pivot points. For the relevant Geelong drawing T1647 see item 8044 2 - "Standard Pony Axle" - traced from MMTB drawing R3755 3 - "Pony Axle Box" - traced from MMTB drawing R1112 and dated in ink 28-4-1955Yields information about Brill 22E brake rigging and equipment.Set of three Drawings - dyeline print on plain paper with a brass clip in the top right hand corner.tramcars, brill 22e, pony axles, axles, axle boxes, brake rigging, ballarat, geelong, drawings

Made by internee at Camp 3, Tatura and used there by childrenHandmade large wooden model of a cartor dray, painted brown and green. Has metal axle type arrangement under front wheels with attachment for horse model. 2 x removable panels front and backcart, beck k, camp 3, tatura, ww2 camp 3, toys, general, handcrafts, wood, carving

Constructed by David Hawksworth of the UK, based on photographs and sketches of a Ballarat tram. Demonstrates model making using cardboard and model parts.Model of Ballarat 26 made from cardboard painted or colour photocopied onto cardboard and glued. Has two operable axles, each with a wheel - 30mm gauge. Trolley pole made from a plastic tube.models, tramcars, ballarat, david hawksworth

Photograph of an Melbourne Tramway and Omnibus cable tram showing the axle box, springs and wheel supporting the body of a trailer. Shows the side skirts around the wheel. Part of the brake rigging can be seen as well.Yields information about cable tram trailers wheel sets.Black and white photograph on paper. Two copies held.trams, tramways, mtoco, cable trams, trailers, wheels, axle boxes

"J547 undergoes maintenance that required removal of its motion gear, axle box and wheel set. The dome cover has also been removed to facilitate a boiler inspection and/or work on the regularor valve. November 1962" - NewsrailDigital TIFF file Scan of 35mm Ilford FP3 black and white negative transparencybendigo, bendigo railway station, george coop collection, j-512, j-547, j-class steam locomotive (vulcan foundry), railway turntable, railway workshop

Instruction - printed on two A3 sheets, titled "The Care of Railway Motor Bearings" issued by General Electric July 1925. Details bearing lining materials for brass and Babbitt, armature, axle, iron, packing, oil levels and inspection. Original from a wall poster.trams, tramways, electrical engineering, electrical equipment, motors, electric traction, general electric, bearings, maintenance

Delivery docket number 96686. Form 1/118 - Jan 1959. Delivery details handwritten in blue ink. To "Mr R Prentice T M S" (TMSV) From "Preston" (?) "4. whitemettaled Saddle brasses" - (for use as Axle bearings) "Sundry Debtor. H.O."trams, tramways, preston, forms, equipment, axles, tramcar equipment, tmsv, bearings

Black and White photograph of a set of recovery trolley's under a road vehicle rear axle - Reg No. V1283. shows the nature of the construction of the trolley and dual rear tyred vehicle. Has a towing pin - possibly one of the recovery vehicles. Mid 1970's? Photographer unknown.trams, tramways, recovery, accidents

Four wheel flat top track trolley- deck wood frame and sides on four fabricated/pressed wheels, with bearings, axles- Used to transport materials- hand pushed or towed. Metal tie rods in front over axles and metal has connecting tow/couplers. Relocated to Bungaree c2015 when 22 moved. Photographed at Bungaree 6-4-2020 by Neville Britton, see image btm18i1.jpg. Record updated 6-4-2020. See detailed information on back of sheet in folder for sketches, timber damaged, notes re a number plate and a note regarding work done 7/97 in replacing underside diagonal bracing supports.On underside in paint, "To Cargeeg, 50 Pasadena East Bentleigh, Melbourne"trams, tramways, commonwealth railways, maintenance equipment, railway trolley

This traction device was made to increase traction and braking on slippery surfaces eg. snow / ice and can be fitted on two wheels on one or more axles of a vehicle. These devices can fit many wheel sizes. these 'snow chains' were used in the early 1970's.These vehicle traction devices were used at Falls Creek during winter.Rusted steel device used to grip vehicle wheels to enable traction over slippery surfaces. Four steel curved prongs connected at a solid steel rectangular centre. Each prong has teeth at the centre enabling it to fit through and be moved for tightening. The prongs are at 90 degrees to each other. The steel prongs are 'waved' on the outer wheel where they contact the surface of the ground. On the outside of the centre piece a coiled piece of steel is attached extending out to curve around one of the prongs Inside centre on steel rectangular plate: "Christiana Spigervek" / "Norway Patent Nos. 116148 / 116188 / Norway / Foreign Patents Pending."snow chain; vehicle traction device; falls creek

.1 - Book - 16 pages + light grey cover, issued by the British Engineering Standards Association, British Standard Specification for Tramway Axles. Dated August 1921. Has standard Number 101-1921. Provides materials specification, testing and an index. Inside the front cover is a typed quarto sheet, that has been folded into four referring to the standard and "Amendments suggested to clauses 1, 8, 9 , 12 and 13". .2 - Book - 24 pages + grey covers, - Tentative Australian Standards specification for Tramway Axles, published by the Australian Commonwealth Engineering Standards Association, No. C 44 - 1927. Provides materials specification, testing and an index. .3 - Book - 28 pages + light grey cover, issued by the British Engineering Standards Association, British Standard Specification for Tramway Axles. Dated August 1921. Has standard Number 102-1930. Provides materials specification, testing and an index. On front cover and inside cover has amendments and a note that the British standard had been endorsed by Australian Standard C44 in Dec. 1933..1 - has the stamp of the "Tait Book Co. 39 Queen St. Melbourne" .2 - has in the top right hand corner, the ESCo Ballarat company stamp and the date "31 May 1928" .3 - on front cover stamp " Library Copy M.E.S." and a library label noting that the book is on loan from the Melbourne library and is dated 22/1/1935. Provides materials specification, testing and an index. On the lower edge has the stamp of the "Tait Book Co. 39 Queen St. Melbourne".trams, tramways, tramways, electrical equipment, axles

Colour photograph of BTM tram 28 wheels loaded onto a John Clowes supplied trailer for transport to AETM Adelaide on 8/1/1999 for reprofiling. In photo are John Clowes (standing by car), Stephen Butler, Simon Jenkins and Alastair Reither and two other people. Trailer positioned over pit in 5 road. Used in Feb. 1999 issue of Trolley Wire, page 41. Note spelling of John Clowes name in caption is "Clowes". Photo by Darren Hutchesson. Photo on AGFA Prestige paper.On rear of photo in blue ink "8/1/99 / Car 28, wheels/axles being loaded onto John Clowes' trailer for transport to out friends at AETM St Kilda - for reprofiling. / Photo: Darren Hutchesson"wheels, 28, aetm, btm, john clowes, tram 28

Gives details for each tram at that time, where from, date of purchase, New or second hand (all ), Straight or drop sill or drop centre, Body builder, Seating capacity, overall length, overall height, overall width, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel diameters, wheel base, axle diameter, motors type and maker, Motor horsepower, Gear Teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and whether suitable for one man operation. Side list gives details of abbreviations, list of tram types and note on Birney 15. List of trams include "Cleaner Car". Undated. See item 3430 for Ballarat version and 8721 and 8722.Yields detailed information about Bendigo trams -c1964Dyeline print from a typed list.2nd copy has in ink "BTPS 613" in the top right hand corner.tramcars, bendigo, equipment, lists, data