Blue hardcover book titled The Westinghouse Brake Reference Book, contains technical information relating to locomotives braking system along with diagrams.Handwritten notes inside front cover J.H.Badhan 16 Abbott St Bendigo & inside back cover J Badham C/O Loco Sheds Bendigo.The Westinghouse Brake Co of Australia Ltd Concord West NSWbooks, technical, trains

Has a table of contents, outlines the rules of operating brake equipment fitted to tramcars, the SM3, SX2 brake valve, locomotive straight air, installation piping, wiring, maintenance - piston travel, lubrication, car tests, hints to Motormen and Conductors and General Hints. Schedule for SM-1 and featherweight equipment. Includes instructions on compressors, air intakes, valves, cylinders and governors.Provides instructions about Westinghouse air brake equipment used on tramcars around the world.Instruction - 48 pages + light brown card cover centre stapled with cloth binding on outer edge + 13 fold out drawings inside the rear cover, titled "Westinghouse - T5001-1 Straight-Air Brake Equipment". Dated March 1923. On first page a signature in ink - "W. Armstrong"?brakes, electrical engineering, •electrical equipment, •westinghouse, •air compressors, •instructions, •maintenance

Two page brochure, with two drawings attached, for Westinghouse M3 Feed Valve and pipe brackets. On bottom of front page The Westinghouse Brake co. of Australasia Ltd., Head Office and Works: Concore West, N.S.W. 1931.The Westinghouse Brake Co. Of Australasia Ltd. Concord West, N.S.W.organisation, commerce, westinghouse

Drivers were highly skilled enginemen. Taking a train from Beech Forest to down to Gellibrand required the train to be controlled at 10 mph (16 km) without running out of air. When a brake application was made the brakes on the locomotive were applied harder than the train brakes. The brakes locked up and the engine would just slide along. Drivers used a retention valve on the loco, then released the loco brakes so as not to wear out the brake shoes. So the train pulled into Gellibrand ready to pull out again after refilling the loco with water.At Gellibrand, a Down goods train is about to depart the station on 14 December 1955. The train consists of the locomotive G42, a louvre van NO, two NQ wagons and a guard's or brake van NC. B/W.gellibrand; colac; beech forest; railway;

Instruction - 3 sheets of a former 8 or 12 page document titled "Westinghouse Magnetic Brake" describing the mechanism for magnetic and clamp brakes on 21E trucks, bogies, 22E, trailers. Lists the advantages of the Westinghouse Magnetic Brake. Has a note on the last pages that 2000 Westinghouse Magnetic Brakes have been sold in Great Britain along up to Nov. 1904. Presumed published in the UK by The British Westinghouse Electric & Manufacturing Co. Ltd. London and Manchester.trams, tramways, westinghouse, instructions, maintenance, brakes

Drawing details brake rigging and dimensions for a Brill 22E truck. Dated 4/8/1947, prepared by the SEC Geelong branch, signed by H N Hornabrook 6/8/47 showing the layout and loads on each part of the brake system, drawing No. T1647. See item 9025 for another version.Yields information about the brake rigging for Brill 22E trams and demonstrates the activities of the SEC Geelong office.Drawing - blueprint, titled "Brake rigging dropped centre double bogie tram Brill maximum traction truck 22E, Trams Nos. 31,""D1775" in ink on top sheet right hand corner.brill 22e, drawings, brake rigging, geelong

Drawing of the brake system on a Melbourne W3 tram. Drawing R5956trams, tramways, mmtb, braking, w3 class, brake rigging, brakes

Document - for the training of tram drivers of W class trams with modified braking systems. Has a table of contents, explaining the changes, vigilance control, emergency, and park brakes. This system followed several rear-on collisions due to indifferent braking systems. Produced by Yarra Trams June 2002.Yields information about the modified braking systems on W class trams.Document - 16 A4 pages was stapled in top left hand corner.trams, tramways, w class trams, brakes, driver training

Manuscript - two typed quarto sheets - titled "Ferodoisation" written by "Dick Kerr", looking at the use of Ferodo brake shoes in Melbourne. Looks at costs, service, noise, braking, disadvantages of noise, smell, dust and braking effort. See also Reg Item 3054 - "Electric Traction - May 1969", that has an article by "Richard Kerr" - most likely the same author and the collector - Bob Prentice. With the manuscript are two photographs of the brake blocks and drawing of a wheel marked Fig 1 and Fig 2 - these are not referenced in the article.trams, tramways, mmtb, brakes, ferodo brakes shoes, braking, tramcars

NC Van The NC guard's vans were originally classed NDD. In the 1910 reclassification they were classified NC. Apart from the windows and height they were externally the same as the NBC vans. Inside there were benches along both side walls. One end was equipped with a small guard's compartment. This had two corner seats, two desks with ticket selling windows and a letter rack. A novel feature was a folding dog cage under one of the benches. Six NC Brake Van / Guards Vans were built by Victorian Railways 1 NC was built in 1909 as NDD and reclassed 1NC in 1910. 2 NC was built and placed into service Nov 1912 3 NC , 4 NC and 5 NC were built and placed into service June / July 1914 6 NC was Built and placed into service in 1919 1 NC, 4 NC and 6 NC were all scrapped by Victorian Railways between 1954 and 1957 Van 5NC - Brake Van (4 ton capacity) In Active Service - Belgrave Station Yard VR Service History: 5 NC *NC 5.VA - 31/ 7/1914 NWS Built new - / 6/1926 - Modified AC Malco 16/11/1932 NWS Into Workshops - 9/12/1932 NWS Out of Workshops (24 days) 23/10/1935 NWS Into Workshops - 19/11/1935 NWS Out of Workshops (28 days) 10/ 8/1939 NWS Into Workshops - 8/ 9/1939 NWS Out of Workshops (30 days) 2/ 6/1944 NWS Into Workshops - 25/ 8/1944 NWS Out of Workshops (85 days) 21/ 4/1949 NWS Into Workshops - 14/10/1949 NWS Out of Workshops (178 days) Dec 2016 - Puffing Billy Register of Rolling Stock NC 5 Brake Van (4 ton capacity) - In traffic Historic - Victorian Railways - Narrow Gauge Rolling Stock - NC Brake Van Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock CollectionBrake Van (4 ton capacity) made of Timber and wrought iron5NCpuffing billy, 5nc, 2'6" gauge, victorian railways, 5nc brake van

"Westinghouse Australia self-lapping driver's brake valve Type W" circular No. C6 dated 1936, describing the type of brake valve, its features, operations, adjustment, associated double check valve and drawings shown with parts. This type of valve was used by the MMTB, replacing the Manual Lap type on almost the entire fleet. It gives a lot better control over the braking of a tram by drivers.Yields information about the Westinghouse Type W brake valve.Document or catalogue circular - 4 loose pages, quarto No. C6tramways, technical information, tramcars, brakes, brake valves, westinghouse

Cast steel and machined Self Lapping air brake handle stamped "CAR 19". Could have been allocated to Freight car 19 or 19W.trams, tramways, brakes, tramcar component, preston workshops

Document - "Ferodo brake shoes" - dated 26/1/1968 advising that as of 29/1/1968 a start will be made to fitting non-metallic (Ferodo) brake shoes to wide-body trams at Malvern Depot. Notes that Preston and North Fitzroy Trams have had them fitted since 4/1967. Provides information about their characteristics and changeover as cast iron shoes wear out.Yields information about the timing of the fitting of a different type of brake shoe on trams that were a lot more effective than cast iron and their background history.Document - single foolscap sheet with two punched holes on left side.tramways, trams, ferodo brakes shoes, brakes, malvern depot

Issued to employees of the VR St Kilda to Brighton electric street railway, superseding previous copies. The line closed in 1956. Note the spelling of the word "employe" with an accent over the e - an acceptable practice in Victoria at the time - a US based spelling. Book scanned into multiple parts. See Reg Item 3508 for a "Supplement to the Book of Instructions re the working of the St Kilda and Brighton Electric Street Railway, dated 1/1/1915", item 7518 for a June 1907 version, and 7580 for instructions issued in 1911.Demonstrates a Victorian Railway Rule book for electric tramways or Street Railways.Rule Book - 156 pages, five sewn sections within a green coloured Rexene heavy card with glued endpapers with the title "Victorian Railways Instructions re Working of the St Kilda and Brighton Electric Street Railway" and "1927" in gold block. Dated 1 June 1926. Has a table of contents and index - gives definitions - "trams" vs "street railways", general instructions, hand signs, working of cars, working of traffic over single and double line, staff and ticket systems, air brakes, permanent way, overhead, fares, appeals of employees against penalty and electric shock.Copy 3 has stamp of the "Westinghouse Brake Inspector" and "Lloyd Rogers" in ink on the inside front cover. On page 94 and 95 has notes in pencil about the air braking system - may have been for a following issue.trams, tramways, victorian railways, vr, st kilda brighton, rules, employees, safeworking

Instruction - duplicated foolscap sheet - titled "Instructions to Motorman - Trams equipped with automatic brake apparatus" detailing the use of equipment that was fitted to a limited number of four motor tramcars. trams, tramways, controllers, brakes, instructions

Instruction - 64 pages + light brown card cover centre stapled with cloth binding on outer edge + fold out drawing inside the rear cover, titled "Westinghouse - T5001-1 SM3 Straight-Air Brake Equipment". Dated March 1927. Has a table of contents, outlines the rules of operating brake equipment fitted to tramcars, the SM3 and PV brake valves, SX2 brake valve, locomotive straight air, installation piping, wiring, maintenance - piston travel, lubrication, car tests, hints to Motormen and Conductors and General Hints. Includes instructions on compressors, air intakes, valves, cylinders and governors.On inside cover "Bob Prentice 13 High Street Prahran Vic 3181" and on top of first page "W. Armstrong"trams, tramways, electrical engineering, electrical equipment, westinghouse, air compressors, brakes, instructions, maintenance

Demonstrates a hand written note about the coefficient of friction.Foolscap sheet - titled "Some special Co-efficient of Friction" setting out parameters for steel tyres and rails, cast iron brake blocks, velocity and types of paving. Hand writtentrams, tramways, brakes, reports, tramcars

Hand brake pawl, possibly from a cable or horse tram, smaller than an electric tram version consisting of a cast or forged pawl with a forged, turned and threaded bolt, steel washer and nut. Components have been removed from very rotten wooden floor. Possibly c1900tramcars, brakes, handbrakes

35mm Kodak white cardboard colour slide by Keith Kings of per way works car No. 15 being used to transport brake shoes (blocks) around the depot. Being loaded at Preston Workshops. 16/4/1968Keith Kings stamp and number "21-36", with details of exposure. in ink "MMTB No. 15 (ex Q 198) being used to transport brake shoes around the depot. Being loaded at Preston Workshops.trams, tramways, work trams, brake blocks, tram 15

NC Van The NC guard's vans were originally classed NDD. In the 1910 reclassification they were classified NC. Apart from the windows and height they were externally the same as the NBC vans. Inside there were benches along both side walls. One end was equipped with a small guard's compartment. This had two corner seats, two desks with ticket selling windows and a letter rack. A novel feature was a folding dog cage under one of the benches. Six NC Brake Van / Guards Vans were built by Victorian Railways 1 NC was built in 1909 as NDD and reclassed 1NC in 1910. 2 NC was built and placed into service Nov 1912 3 NC , 4 NC and 5 NC were built and placed into service June / July 1914 6 NC was Built and placed into service in 1919 1 NC, 4 NC and 6 NC were all scrapped by Victorian Railways between 1954 and 1957 2NC - Brake Van (4 ton capacity) VR Service History 26/11/1912 NWS Built new 2 NC *NC 2.VA - 26/11/1912 NWS Built new - circa 1926 - Modified AC Malco BO 6/ 7/1932 NWS Into Workshops - 5/ 8/1932 NWS Out of Workshops (31 days) 2/10/1937 NWS Into Workshops - 3/12/1937 NWS Out of Workshops (63 days) 25/ 1/1945 NWS Into Workshops - 23/ 2/1945 NWS Out of Workshops (30 days) Dec 2016 - Puffing Billy Rollling Stock register Puffing Billy Service History or Notes 21 Oct 1995 - Loco 7A and 2 NC collides with trolleys NK 3, Jenny, & NG 1 on the SELBY side of the MONBULK CREEK trestle bridge. Historic - Victorian Railways - Narrow Gauge Rolling Stock - NC Brake VanBrake Van (4 ton capacity) made of Timber and wrought iron2NCpuffing billy, 2nc, 2'6" gauge, victorian railways, 2 nc brake van

Instruction - 24 pages, with two punch holes and stapled on the left hand side titled "Air Brake Safety Car Control Equipment" number 84450.1B, pages 3 to 26. Details the M28 brake valve, sanding features, operation, door and step controllers, check valve, CP-25C air compressor, brake valves, air compressor governors, drawings of piping, maintenance, testing, faults and general operation. See Reg Item. 3478 for another similar document. No details as to who published it or dates.trams, tramways, electrical engineering, electrical equipment, air compressors, brakes, instructions, maintenance, controllers

Report - 7 A4 sheets - Photocopied, stapled into the top left hand corner, titled "Report for Department of Infrastructure on Investigation into Braking Irregularity on R1808 on Sunday 12 October 2003", prepared by Safety Action Pty Ltd 20/11/2003. Has a table of Contents. Gives the background to the braking issues suffered by R1808, Sydney Tram operated by Bendigo Tramways, summary, investigation, factual circumstances, findings, conclusions, recommendations and references.trams, tramways, accidents, brakes, tours, sydney trams

The photograph shows the procedure for releasing the drum brakes on PCC tram 980 and where the brace (spanner) is located on the tram. Dated 24/8/1960.Demonstrates the methodology of releasing the drum brakes on a PCC car.Photograph - black and whiteHas MMTB stamp on rear and number P25/1/248 in ink.trams, tram 980, brakes, pcc class, tramways, mmtb, st. louis b3

Set of 5 instructions prepared for use at Malvern Depot c2000, regarding use of trams - printed on A4 sheets. .1 - "Emergency Braking Procedures for Tramcars - Two motor Single Truck Trams" - 1 page .2 - "Emergency Braking Procedure for Tramcars - Four motor Bogie Cars (L & W Class trams) .3 - "Tramcar Braking - The Air system" .4 - "Brake Valve with Sanding Feature" - (Birney 217) .5 - "Malvern Depot Training" - Z1 - Z2 - Z3 class - 4 pages. .6 - "Fault Finding" - covers Z and W class trams. .7 - "Tram driver fault finding & Braking assessment B and Z class" - assessment sheet and pages 1 to 9 of 13 original sheets, four missing, dated 9-4-1999 - added 17/6/2019.trams, tramways, swanston trams, brakes, emergency, safety, drivers, malvern depot, z class, w class, x class, b class

Instruction - 48 pages + light brown card cover centre stapled with cloth binding on outer edge + 13 fold out drawings inside the rear cover, titled "Westinghouse - T5001-1 Straight-Air Brake Equipment". Dated March 1923. Has a table of contents, outlines the rules of operating brake equipment fitted to tramcars, the SM3, SX2 brake valve, locomotive straight air, installation piping, wiring, maintenance - piston travel, lubrication, car tests, hints to Motormen and Conductors and General Hints. Schedule for SM-1 and featherweight equipment. Includes instructions on compressors, air intakes, valves, cylinders and governors.On front cover in ink "Mr McLaren"trams, tramways, electrical engineering, electrical equipment, westinghouse, air compressors, brakes, instructions, maintenance

Set of four drawings of electrical and brake equipment on VR Tramcars. .1 - No. 1 - Bogie car wiring diagram - shows all equipment including lights, compressors, motors and switches. Has a different lighting circuit for the 52 to 54. 4 copies held. .2 - No. 2 - Air and Brake Equipment (Excluding one-man car) - shows all equipment including wipers, conductor's brake valve .3 - No. 3 - Pneumatic Equipment for One-man car - shows all equipment including door engines, emergency valves, emergency reservoirs, door valves and links to controller. .4 - No. 4 - Pneumatic Door Equipment - cars 52 to 54 - including door controller valve positions.trams, tramways, vr class tramcars, victorian railways, brakes, wiring diagrams, one man trams, air compressors

Typed report on the type of brake shoe fittings fitted to each tram as at 8/7/1963. The report lists each passenger tram from VR 52 to W71040, and what their status was if not in use - eg stored, sold, scrapped. The list excludes the early MMTB trams of A to V class. Works cars are not listed. Yields information about the status of the MMTB Passenger fleet in 1963 and the type of brake shoe types fitted to each.Document or report 5 foolscap sheets - carbon copytramways, tramcars, lists, scrapped trams, brakes