The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only. Black and white photograph of an experimental steam engine which was produced for the Ballarat School of Mines. It was designed for experimental purposes, such as testing of efficiency, etc. The laboratory which housed the steam engine was lit with gas lighting. davey paxman experimental steam engine, model steam engine, davey paxman, steam, thomas bath, thermodynamics

This item is part of the Di Reidie collection. Diane Reidie was a much loved volunteer and President of Brighton Historical Society from 1999 until 2016. Originally from New Zealand, Di and her family lived in Male Street, Brighton for many years. A vibrant and energetic person with a zest for life and a gift for bringing people together, Di was a friend to many in the Bayside community and active in local community organisations. Her tireless work as President of BHS saw her named Bayside Citizen of the Year in 2008. As a seller and collector of vintage clothing, she was passionate about fashion history; one of her many enduring contributions to BHS was her extensive work in preserving, developing and promoting the Society's costume collection. In 2018-19, Di donated more than one hundred items from her personal vintage clothing collection to the Society. The collection, which includes clothing, hats, handbags and shoes from local and international designers, is representative of Di's wide-ranging interests, colourful personality, creativity, humour and love of fashion and travel. This jacket originally belonged to Australian singer, actress and philanthropist Olivia Newton-John, who autographed it and donated it to be auctioned at a Leather and Lace Ball for the Austin Health Olivia Newton-John Cancer Centre Appeal on 15 May 2004. Newton-John has long been an advocate for cancer research and awareness, having undergone multiple treatments for cancer, a disease Di also battled for many years. Di's husband David purchased the jacket at the auction for around $1,000, and it has since been much worn by Di and her daughter Kathryn. The nature of the jacket - which is faux-leather, with glued-on diamantés, suggests that it was likely part of a stage costume rather than an item from Olivia Newton-John's personal wardrobe.Black polyester leather look jacket with black polyester lining. The jacket features a centre front opening secured by six black press studs, two bust height flap pockets with press studs, and collar. Full length sleeves with band and black press stud closure. The jacket features diamanté decorative finish along the collar and shoulder placket. "IMMAGINE, Made in Italy" "40" "Made in Italy, Fabrique en Italie, 100% Polyiestere, Polyestere, Polyester, Polyester" Personal signature of Olivia Newton John in fine silver pen, "Love Olivia Newton John, 04".olivia newton john, stage costume, olivia newton john cancer centre, austin health, di reidie, immagine, 1990s

Brighton councillor Sally Allmand's grandmother Minnie Toms (1878-1983) began making this dress and matching jacket in the 1920s, but never finished it. Sally's mother (also named Minnie, 1914-2001) finished it in the 1970s and Sally wore it when, as Mayor of Brighton in 1981, she was introduced to the Queen during a Royal visit.Sleeveless black floral lace dress (.1) with v-neck and matching collarless jacket (.2) with scalloped bottom hem.sally allmand, minnie toms, brighton council, politics

Built by Aveling & Porter Ltd., Rochester, Kent, England Builder’s Number 11629 of 1923 Weight 10 Tons Used by the South Melbourne Council in road construction between 1926 and 1963 Aveling and Porter was a British agricultural engine and steam roller manufacturer. Thomas Aveling and Richard Thomas Porter entered into partnership in 1862, developed a steam engine three years later in 1865. The company became the largest manufacturer of steam rollers in the world. Service History : Title: City Surveyor's report Creator: Johnson, A.L Publisher: Prahran City Council Date: 1921 .... The 10-ton steam roller worked 302 days, the Aveling and Porter 12½-ton roller worked 211 days while the Garrett steam wagon continues to carry tar and road materials. city of prahran annual reports 1912-1913 http://www.stonnington.vic.gov.au/files/assets/public/history/city-of-prahran-annual-reports-1912-1913.pdf Industrial Steam Roller - Road Construction, South Melbourne, Victoria, Australia Aveling & Porter 10 ton Steam Roller with roof and rear tool box Builders Number 11629 Aveling & Portersouth melbourne, puffing billy, steam roller, aveling and porter, puffing billy museum, road construction, road steam

The Uebergang family lived at Tooram Park, Allansford from 1912 to 1992. The bed jacket is part of a collection of items relating to rural life in the mid 20th century.White cotton bed jacket with scalloped satin stitch edging and cut work with butterfly motif lace insertions. Front closing with press studs and a tie. Cap sleeves with a V-shaped slit and butterfly motifs either side.201 (on tape at the side)costume accessories, female costume, uebergang, allansford, women's bed wear

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.Black and white photograph of the Davey Paxman Experimental Steam Engine installed at the Ballarat School of MInes. steam engine, model steam engine, davey paxman, thomas bath, experimental steam engine

Series of 6 photos, Steam train "D", 3 class and passenger carriages at Stawell Station. c 1990Series of 6 colour photographs of Steam Trains & passenger carriages at Stawell Station "D" 3, ?39 unsure of first number.railways

Article about the annual visit of the steam train J515, operated by the Seymour Railway Heritage Centre, to Yarrawonga in April 2000. The train driver was Alan Fish.Newspaper cutting with photograph showing the front of a steam train and a man in overalls.trains, steam train, j515, seymour, yarrawonga, alan fish

This is one of the many steam rail specials heading for Yarra Glen or Belgrave and Puffing Billy. Sunbury Crescent is seen on the RHS of the photo.A coloured photograph of a steam train identified as 515 with a red coloured carriage behind it.steam trains, sunbury crescent, surrey hills station, rail specials

Advertising flyer from the Seymour Loco Steam Preservation Group Inc. publicising the last steam train to run between Springhurst and Wahgunyah on 19th September 1992.steam trains, trains, wahgunyah-springhurst train, wahgunyah, springhurst

Steam Locomotive - 1711 Peckett “Sir John Grice” Date built - 1926 Locomotive type ; Cranmore Original owner - Metropolitan Gas Coy., West Melbourne Original gauge - 762mm Withdrawn - 1941 Next owner - Whistle Stop Amusement Park, Frankston Built in 1926 for the West Melbourne site of the Metropolitan Gas Company, and issued to traffic the same year this saddle tank locomotive was named “Sir John Grice” in 1928. It was withdrawn from traffic in 1941 and stored until sold privately in 1962. In 1965 it was sold again and went to the Whistle Stop Amusement Park in Frankston and again stored until bought at auction by the Puffing Billy Preservation Society in 1974 and put on static display in the Steam Museum. Restoration started in 1978 and it was returned to service in 1981 painted light green with yellow lining. It is temporarily renamed “Thomas the Tank Engine” with a fibreglass “Thomas” body cover each time it appears in the “Thomas the Tank Engine” shows at Gembrook station.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used at the Metropolitan Gas Coy., West Melbourne, Victoria, AustraliaSteam Locomotive made of steel, wrought iron Peckettpeckett “sir john grice”, 1711 peckett, puffing billy, steam locomotive, industrial narrow gauge railway, metropolitan gas coy., west melbourne

The photo was taken at 8.15am on Friday 12 September 1919. The D class was a passenger and mixed traffic steam locomotive which operated on the Victorian Railways from 1902 to 1974. Originally it was introduced on mainline express passenger services, but they were quickly superseded by the much larger A2 class and were relegated to secondary and branch line passenger and goods service, where they continued in service for the next fifty years. The D716 was probably built at the Newport Workshops, post 1910 and before 1914. The expansion of Melbourne's population into new suburbs early in the 20th century, and the delay of the suburban electrification project, meant there was the need for faster and more powerful steam locomotives for the suburban rail network. In 1908, the basic design was adapted to create a more powerful locomotive. They were put to work on longer and hillier suburban routes including the Lilydale line. A total of 58 were built between 1908 and 1913. See wikipedia for a more detailed history of the D class locomotives. Electric trains replaced steam in 1922. Mr William Holmes of 'Lugano', Mont Albert Road was in charge of the design and introduction of the electrification of the Melbourne rail system.Black and white photo of a steam train approaching the platform at Mont Albert station. Rear in blue biro in Jocelyn Hall's handwriting: "Hamilton St Mont Albert / probably 1919".mont albert station, railways, trains, d class locomotives, norman carter, steam trains

Steam Train Engine in Hills cutting c 1940. Photo from "Boothey" EstateTwo identical photos of a steam engine & goods trucks heading towards Melbourne. The larger photo a copy of the smaller photo c 1940A543 printed on the back of one of the photos.railways

The Davey Paxman Experimental Steam Engine was purchased by the Ballarat School of Mines as the result of a bequest from Thomas Bath.The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.davey paxman experimental steam engine, model steam engine, steam, thermodynamics laboratory, thomas bath, bequest

For an explanation about the history of steam engine indicators, visit: http://www.archivingindustry.com/Indicator/contentback.htm [last viewed 20 May 2013]. For information about the Richards' Improved Patent Steam-Engine Indicator see John Walter's publication 'The Engine Indicator: a short history of the autographic patterns from 1800 to the present day' - available online via: http://www.archivingindustry.com/Indicator/chaptertwo.pdf Information on Casartelli, Manchester is also available online via: http://www.archivingindustry.com/Indicator/chapterfour.pdf Refer pp.21-22 [last viewed 20 May 2013]Brass steam-engine indicator 125mm tall - accompanied by four steel piston springs - and a wooden measuring ruleIndicator [a] Casartelli Manchester [b] 41 ; Ruler [a] 12 to the Inch [b] No.2 [c] Casartelli & Son Manchesterrichards improved patent steam engine indicator, casartelli manchester

RAAF Jacket

White dress jacket

2 Coloured photos of D Class Steam Rail Locomotive and one Black & White of same engine at Cato Park. c 1974. The engine was subject to vandalism and removed in 1988. The black & white photo of D3 608 was copies from a railway magazine. Two coloured photos & one black & white photo of "D" class 608 Steam rail Locomotive taken at Cato Park. "D" 608. Inscription on the back of both colour photos, "Vec 74. D Class Loco at Cato Park". On the black & white photo " D3 608 one of the numerous and popular D3 class, preserved in a park in Stawell, 2nd April 1978".railways.

The Davey Paxman Experimental Steam Engine was purchased as the result of a bequest from Thomas Bath. The 'substantial sum' was used to build an Engineering Laboratory. The Ballarat School of Mines Council minutes of 08 November 1901 record: - Plans for [the] proposed building were submitted ... and ... it was resolved that a temporary building for an Engineering Laboratory be put up.' This laboratory, as an existing building, is first mentioned in the Ballarat School of Mines President's Annual Report of 1901, presented on 28 February 1902, reporting 'the erection of a building 67ft long by 33 ft wide' This report also lists all the equipment that would be accommodated in the Engineering Laboratory, including the experimental steam engine and boiler. The experimental Davey-Paxman steam engine arrived in Ballarat towards the end of 1902. The Engineering Laboratory was opened on 14 August 1903 by His Excellency Sir Sydenham Clarke. This engineering laboratory remained in use till about 1945. By 1944 preparations were under way at the Ballarat School of Mines to expand existing facilities, to be ready for the influx of returned soldiers. A new Heat Engines laboratory was built, this time of brick construction, replacing the previous corrugated-iron shed. In the early stages the steam engine was used to drive an overhead transmission shaft for machinery in the adjacent workshop. Later the steam engine was moved to a space that became the Heat Thermodynamics Laboratory. At the end of 1969 the engine was relocated to the Thermodynamics Laboratory at the then Ballarat Institute of Advanced Education (BIAE) Mt Helen Campus. It was donated to Sovereign Hill in 2006. According to the research of Rohan Lamb in 2001 around five experimental steam engines were made by Davey Paxman, and three of these had similar configuration to the Ballarat School of Mines Steam Engine, however, each of these was also unique with different valve arrangements. The list, which was on a scrap of paper in a folio held in the Essex Archives, confirmed that one was sent to India. The Ballarat steam engine can be dated to late 1901 to early 1902. Zig Plavina was responsible for moving the steam engine to Mount Helen, and worked on it as a technician for many years. He observed the following: * The condenser is driven by the low pressure engine. * The following arrangements are possible: i) the high pressure engine alone, exhausting to atmosphere. Condenser not used, crankshaft flanges not coupled. ii) crankshafts coupled, mains pressure (120 psi) steam supplied to high pressure engine, partially expanded steam delivered to low pressure engine (Tandem operation). Choice available re exhaust steam: either to the condenser or to atmosphere. iii) crankshafts not coupled, reduced pressure steam supplied to low pressure engine. Exhaust steam - either to the condenser or to atmosphere. * Valve arrangement - a choice of Pickering cut-off or throttle governor. On low pressure engine - throttle governor only.Black and white photograph of the Davey Paxman Experimental Steam Engine. On the brake is returned serviceman Norman WIlliam Ludbrook (Diploma Electrical Engineering, 1952). Far right is Roy E. Mawby (Diploma Electrical Engineering, 1950)steam engine, model steam engine, davey paxman, electrical engineering, laboratory, scientific instrument, norman ludbrook, norman william ludbrook, roay mawby, roy e. mawby

Steam Engine with 12 men and 3 young children standing along side the train engine. based on the surrounds, its presumed the photo was taken at Heatherlie Quarry. No names are known of people.Black & white copy of photo of Steam engine with 12 men and 3 young boys standing alongside the engine presumed the photo was taken at Heatherlie quarry. railways

This jacket was bought in England for Elsie Law (nee Russell) by her husband James Lindsay Gordon "Lin" Law in 1930. Elsie used it as a bridge jacket. Lin was born in Ballarat 1881, the eighth child of Scottish migrants James Nicol Law and Margaret Law (nee Bartholomew). BHS holds an evening dress belonging to Margaret Law in its collection (see T0006.1). After leaving school at the age of 11, Lin began working as a salesman. In 1906, he and business partner James Kerr Pearson (also a Brighton local, who lived at 12 Moule Avenue) established the shirt manufacturing company Pelaco. In 1922 the company established its factory at 23 Goodwood Street on the top of Richmond Hill; the 4.3 metre high neon 'Pelaco' sign, erected in 1939, is today heritage listed. The company was known for its innovative approach to efficiency and labour relations, discontinuing Saturday morning work in 1908 and appointing an industrial relations officer in 1928. Lin married Elsie Russell on 12 January 1915 at St Mary's Catholic Cathedral in Sydney and they lived most of their life in Brighton. In 1920 they moved into 'Blairgowrie', 306 St Kilda Street, The eldest their four children, Pauline Margaret Law (born 15 December 1915) ultimately purchased the house with her husband Hugh McLean in 1956 and lived there until 1965 when the house was demolished.Cream silk jacket block-printed with art deco style pattern in red, blue, black and mustard colours. Lined with soft apricot-coloured satin. Wide stand collar. Front fastens low on hip with four silk covered buttons. Label, woven brown on cream silk, centre back: Eileen / Mulholland / Ltd. / 43, Wigmore St., / LONDON. W1.elsie russell, james lindsay gordon law, brighton, pelaco, bridge jacket, 1930s fashion, eileen mulholland, art deco

THis collection of cuttings relates to the Warrnambool Steam Packet Company.The Warrnambool Steam Packet Company was established in 1868 when capital was raised with 2000 shares at a value of five pounds each.It was established to provide passenger, accommodation and a large stock and freight service between Warrnambool and Melbourne.. At the time Stephen Henty was operating three steamers along the coast and at the prospect of losing his Warrnambool trade with the establishment of the new Warrnambool company, he sold one of his steamers , the Edina in March 1868. The first five directors elected were F P Stevens, J G Crammond, WW Jamieson, R B Paterson and George Wood. Fares were from one to three pounds and freight was 17 shillings per ton.The steamers connected with coaches from the north of Warrnambool as far as Hamilton. The cuttings record the financial position of the company for the first ten years. This collection of cuttings is valuable as a research item as it documents the development and operation as well as many of the stake holders in one of Warrnambool's earliest shipping companies. The cuttings are from a range of papers including The Warrnambool, Examiner, The Warrnambool Advertiser and the Argus.Ledger book with blue pages which is lacking the cover. It contains a number of cuttings which relate to the Steam Packet Company.Dated on first page: Monday November 1st 1869. Most of the cuttings are dated and some are from the Examiner. the Advertiser and Warrnambool Standard.warrnambool, warrnambool steam packet company, edina

Owned by William Albert HARRISON (Service Number VX41478; above Link ["WW2 Record"] indicates that Rank on Discharge was Cpl, but other AIF documents, from National Archives Australia [including Proceedings of Discharge - see pdf Media File above], indicate that he was Sergeant, which is consistent with the rank on this jacket). Name not written on item but known to be part of set which includes slouch hat, which does contain the name, and other related items which include Service Number, verifying identity. See further service details in "Links" above. Soldier's name known. Items donated (date unknown) by brother-in-law who was living in Montmorency and was a committee member of MERSL when item donated.Khaki jacket; long sleeve 4 front buttons (attached with continuous leather strip) 4 pockets (buttons sewn on) Shoulder straps (buttons sewn on) Cuff buttons (sewn on) Badges on lapels & on shoulder straps Unit Patches on upper sleeves (Part of set with Slouch Hat, 0030.2)Inside label: V300; 1942; Size (2 - 'faint', may be other numbers indicating size details) Brass badges: Australian Commonwealth Military Forces (both lapels); Australia (both shoulder straps) Badge of rank (Sergeant) - 3 chevrons (R upper sleeve) Colour patches on both sleeves for 2/5 Battalion, 6th Division Second AIF Years of Service insignia - 3 chevrons, indicating 3 years O/S service (R lower sleeve) Unit patches - rectangle black over red (2/5 Battalion, WW2)

A long sleeved green cotton jacketclothing, jacket, mcphail collection