Showing 4553 items
matching a model
-
Seaworks Maritime Museum
Shipbuilders model, R W Miller
Original ship - 11,741 gross tons. 589' x 70' x 30' (179.5 x 21.34 x 9.14m). Oil tanker built by Eriksberg Motor Vessels at Gottenburg, Sweden in 1951 for Hjalmar Bjorge of Norway as the Storheim. Purchased November 1964 and renamed R W MILLER. Had a crew of 39 seamen, including the officers. 1973 sold to Independent Shipping Company Pty Ltd of Singapore. Renamed Cherry Victor. Scrapped 1979. Robert Miller traded under the name R W Miller and Company from early 1912. One of Miller's first contracts was to pick up overburden and spoil from the sinking of the Balmain Colliery shaft and dump it at sea. Miller saw the opportunity to sell this material and he ended up getting a sixpence a ton from a local council and other contractors for use as road bases and building foundations. This close association with coal led to Robert W Miller on 15th January 1913 being given the contract for coal distribution from Sydney Harbour Colliery (Balmain mine). So began a long association with coal. Miller built a fleet of lighters that were used to transport blue metal, sand and coal around Sydney Harbour. This introduction into coal transport opened a prospect for him to enter the larger coal shipping transport. During 1917 Miller purchased a vessel, the taking over 1985 by Howard Smith Industries Pty Ltd, Melbourne. Build date 1951-1979. Ship builders model of the tanker R W Miller in a glass case. The body is painted in colours of maroon, green and grey, the deck with detailed fittings and superstructure, an Australian merchant flag flying from the stern, within a mahogany framed glazed display casePlaque at foot of model: M/T R.W. MIILRT/ BUILT GOT. 1951/ OWNERS R.W. MILLER & CO. PTY. LTD/ LENGTH OVERALL 559.04"/ LENGTH BETWEEN P.P 526.06"/ EXTREME BREADTH 70.00"/ MOULDED DEPTH 39.03"/ DEADWEIGHT TONNAGE 18,500/ MACHINERY B & W TYPE A I.H.P 7, 600" on model: "R.W Miller" painted in black -
Federation University Historical Collection
Equipment - Scientific Instruments, Quickfit Chemistry Set: basic set of 9 items
Collected from the chemistry laboratory at School of Mines. The was being dismantled due to the cutbacks in funding to TAFE and science was no longer being taught. The Quickfit Chemistry Set was the most popular set for schools, colleges and universities. There are nine basic items. It allows the construction of at least eight combinations by adding sections together. A labelled diagram included in the box. Included in the box is a BRANNAN 76mm Immersion Glass Thermometer. These are also used in beer and wine making.Solid cardboard box with molded insert for glass instruments.Model No. 27BU/Mchemistry, ballarat school of minestafe, quickfit chemistry set, schools, colleges, universities, thermometer, brannan, immersion thermometer, scientific instrument -
National Wool Museum
Catalogue, Details of Patent Underpick Rising Box Loom with Patent Angle Dobby, for Henry Weight Coatings
Catalogue of rising box loom produced by George Hattersley & Sons Ltd.about 1926 Modeltextile machinery, george hattersley and sons ltd -
Maldon Vintage Machinery Museum Inc
LINO TYPE MACHINE, prior to 1998
This item was used at "The Tarrengower Times" Maldon, Vic by Ron ADAMSLino-type casting machine with furnace for casting lead plates. Makes type used in printing. Motor made by Crompton Patison. Keyboard to select letters to be cast.MODEL 78 No 17175trades; printing; machinery; casting ; tarrengower times -
Maldon Vintage Machinery Museum Inc
Motor Mower, Maker's name "Charles H Pugh"
Green painted cylindrical lawn mower with rear roller, pull start and no catcher. Regal coat of arms on front housing signifying maker is official motor mower supplier to the Queen. Rectangular petrol tank mounted between the handles above the engine. Small wooden roller in two parts on front. Pale grey plastic cover on starter mechanism. Height adjustment on front roller. Engine controls on right handle.Possibly "Eureka" model.machinery, cylinder motor mower -
Vision Australia
Machine - Object, APH (American Printing House for the Blind), APH Talking book machine, 1980-1990's
APH began producing it's own line of products to satisfy it's clients, outsourcing the manufacturer to overseas companies. This talking book machine, had an optional carry case, and dials to control tone, volume, speed, front buttons to record, rewind, forward, play, and stop tape. Playing both 2 and 4 track tapes, it also had Braille signs next to some of the buttons.Plastic rectangular light brown audio player with buttons for navigational controls, power cord, outlets for ear or head phones and black vinyl protective zip up cover Model no. 3-5194A.audio equipment, royal victorian institute for the blind -
Mont De Lancey
Knife Cleaner, Circa 1910
14" diameter hand-cranked Fly wheel turning through gears, with twin 4" diameter rollers, knife cleaner. Painted green on a red painted base."Original Model Patent"knife cleaners -
Mont De Lancey
Ice Cream Maker
Wooden ice cream maker with three green metal bands around it. Bottom band forms base with a cast iron three feet stand and hand-cranked wheel. Cast iron locking mechanism on top. Wire and wooden handle to carry. Within a metal drum for freezing cream.Original Model 2ice-cream churns -
Mission to Seafarers Victoria
Leisure object - Model Ship, H.M.S Dreadnought, 2014
A modern detailed replica to scale 1:200 of the early 20th C battleship launched in 1906. " The dreadnought class defined the basic form of battleships up to the 2nd WW. Original specifications: Length 526 ft; beam 82 ft; speed: 21 knots cruising Crew complement: 657; Armament: 10 12inch guns; 18 12 pdr guns( 4 shown on model) ; Engines: two turbines driving 4 shafts; weight: 17,900 tons fully laden; coal capacity 2977 tons; The ship was broken up for scrap in 1920 - David Lumsden donor and modelmaker Detailed Model of the Dreadnought 90% cardboard model of early 20th C. battleship one white ensign; on a polished wood plinth with cardboard hand lettered labels. Decks painted pale gunship grey and below waterline bright red. Model on polished wood plinth with bevelled edge.two card labels adhered to plinth: "David Lumsden 2014 Scale 1:72" "H M S Dreadnought"model ships, h.m.s. dreadnought, battleships, ww1, david lumsden -
Flagstaff Hill Maritime Museum and Village
Container - Tin, c. 1930-1955s
This metal tin once contained sewing silk thread used in the making of the ship model, Sovereign of the Seas. Natural silk thread has elasticity and can also be teased out for making fine line for rigging on ship models. ”. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This tin of tailor's silk is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This tailor's silk was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage.Tin, round, with lid. Red label reads “The "A.B.C" Brand Tailors Sewing Silk (Raven) Color Fast. Dyed by a new process. Manufactured from the best raw silks procurable. Warranted. Made in England. Size No. 1/4 LB” .The container has no contents. This tin is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”. “The "A.B.C" Brand Tailors Sewing Silk (Raven) Color Fast. Dyed by a new process. Manufactured from the best raw silks procurable. Warranted. Made in England. Size No. 1/4 LB”, Logo on lid is the intertwined letters of “A.B.C.” flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, ship model sovereign of the seas, jim williams, james bernard williams, ship model tools, ship model making, ship model making accessories, "a.b.c" brand tailors sewing silk, silk sewing thread, textile, tin container for silk thread, ship model, hobby, ship model tool, english war ship -
Orbost & District Historical Society
model, Hodge, Chris, 2006
This model was inspired by the Morgan barn on the Marlo Road, Orbost. It was built by Chris Hodge for the launch of the book, "Barns of the Snowy River" ( Reg. No.2138)The slatted barns are unique to the Orbost district.A wooden model of a three-storeyed slatted barn. The scale is approximately 30:1.The roof is corrugated cardboard painted silver. The waater tank is a tin can covered with corrugated cardboard. The down pipes are made from drinking straws. It stands on ply board.model handcraft woodwork barn -
Flagstaff Hill Maritime Museum and Village
Gramophone, 1911
Until late 1925, all record players reproduced sound by purely mechanical means and relied on a so-called "amplifying" horn to efficiently couple the vibrations of the stylus and diaphragm to the space occupied by the listeners. In 1906, the Victor Talking Machine Company, Columbia's arch competitor, introduced a line of models in which the horn and other hardware were concealed within a cabinet, made to look like fine furniture rather than a mechanical device. They named the new style a "Victrola". It quickly proved to be very popular and successful. Other makers, adopting the distinctive suffix, introduced their own "-ola" internal horn machines, such as Edison's Amberolas and Columbia's Grafonolas. They were soon outselling the external horn models. At first, like nearly all other early record players, all Grafonolas were driven by a spring motor that the user had to wind up with a crank before playing a record. In 1915, Columbia began to introduce electric-motor-driven models, as a majority of urban areas had been wired to electrical grids. The electrified Grafonolas supported both alternating and direct currents from 110 to 220 volts. Electrified Grafonolas never gained the popularity enjoyed by the spring motor-driven versions due to substantially higher prices and a lack of electrical service in rural areas. Grafonolas were manufactured under the 1886 United States Letters Patent No. 341,214 which Columbia Graphophone company acquired through its predecessor American Graphophone Company. Two models were available; a portable table model and bigger stationary floor model, offering limited mobility through the application of casters. The most notable table models included Grafonola Favorite introduced in 1911 and Grafonola Savoy introduced in 1915. The most notable floor models included Grafonola Symphony Grand introduced in 1907, Grafonola Regent introduced in 1909, Columbia Mignon introduced in 1910, Grafonola Princess introduced in 1911, Columbia Colonial introduced in 1913. Various period Grafonolas were introduced in 1917 to cater to an increasingly prosperous clientele. Columbia Phonograph Company began to manufacture a series of ornate, limited edition period machines. These were highly priced (some as high as US$2,100 ) special orders that provided consumers with options to choose styles which matched their interior décor. Although the Gramophone does not have a large monetary value, it is of social significance as it demonstrates the progress made in audio reproduction from the first Edison cylinder machines to improvements that allowed ordinary people to be able to buy music discs and enjoy music in their own homes. Gramophone with internal horn, floor model, mechanically operated by a crank handle. Colombian Grafonola Princess (Type F2) brand. Gramophone is in a wooden display cabinet with room for record storage underneath and is complete with handle. Manufactured in 1911 by Columbia, USA."Columbia Grafonola Type 2 Made in USA"flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, record player, gramophone, mechanical gramophone, floor model gramophone, gramophone record, columbia graphophone company, american graphophone company, columbia, grafonola, grafonola princess, music, playing music, audio reproduction, sound equipment, domestic entertainment, 1911 gramophone -
Mont De Lancey
Decorative object - Baker's Cart Model, Chas W Davis
The collection of thirteen model horse drawn vehicles were carefully handmade by Mr Chas W Davis 1925 - 2002. He was a talented artist and saw doctor. This model of a horse drawn Baker's Cart replicates the vehicle that enjoyed respect from the public during the 1880 and early 1900's. A model of a single horse drawn red enclosed Capital Bakery Cart which is a lightweight four wheeled one passenger horse drawn carriage where the driver sits behind. It has two large and two smaller gold painted spoked wheels with brown rims, grey and black painted seating two gold coach lamps and a sloped red and tan footrest for the driver. There is a brake lever on the right side of the cart which activates the brake on the back wheel. At the rear are two ventilated gold doors and cupboards underneath the seat. There are two silver metal tubular shafts on each side to surround the brown horse which has a black tail and mane. It has the necessary horse tack for cart use to help the driver communicate with the horse. These carrier carts or vans were four wheeled medium weight Commercial Vehicles which were a very familiar sight in the horse drawn era. Every kid 'whipped behind' bread carts. The first models were imported from England around 1870 and later the local coachworks built many models. The biggest producer was Flood in St Kilda Road until 1926.CAPITAL BAKERY is painted in white lettering on each side of the cart.replicas, models, scale models, vehicles, carriages, horse drawn vehicles, toy horses, early commercial vehicles, bread cart -
Flagstaff Hill Maritime Museum and Village
Tool - Saw, 1930-1955's
This tenon saw was used in the making of components for the ship model Sovereign of the Seas. Tenon saws are often used for making dovetail joints. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This tenon saw is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This tenon saw was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Tenon Saw. Hand saw with small-toothed metal blade set into a slotted brass back, attached to a round brass fitting in the light coloured, turned wooden handle. Top on handle is marked with seven concentric rings scored into the wood. On top of blade is maker’s name “AVIA” within oval ring. This tenon saw is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”."Avia" within oval ring.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, saw, wood cutting tool, tenon saw, avia steel and tool company limited, carpenter's tool, tool, sovereign of the sea, ship model, hobby, ship model tool -
The Cyril Kett Optometry Museum
Ophthalmotrope, unknown, (estimated); mid 20th century
This model was used in lectures in the College from the mid 20th century. An ophthalmotrope is a mechanical model constructed to demonstrate the movements of the eyes and the actions of the various muscles which produce them. The first ophthalmotrope was made by Theodore Reute in 1845 and it was he who gave it the name 'ophthalmotrope'. Frans Donders (1818-1889) became interested in eye movements on reading Reute's work, and his subsequent studies were of physiological interest and also provided the basis for principles underlying the correction of squint. Because of the complexity of the actions and counter actions of the eye muscles, ophthalmologists of the 19th century sought a practical solution with the construction of mechanical models. Reute's second model of 1857 was more sophisticated. Its eyeballs contained lenses and the optical system could be moved backwards and forwards to simulate accommodation. Later ophthalmotropes are known by Landolt, Knapp and Snellen.This ophthalmotrope is the one that was used as a teaching aid in the College from the mid 20th century.Brass framed model to illustrate actions of extra-ocular muscles. Two painted wooden globes mounted in brass frame with coloured strings attached to brass weights positioned to show actions of various extra-ocular muscles. Also wooden storage box. Materials: brass, metal, wood, string.optometry, ophthalmology, ophthalmotrope, eye, eye movements, extra ocular muscles, eye muscles, eye teaching -
Bendigo Military Museum
Souvenir - TRENCH ART, c.WWII
Aeroplane model depicts a "P38 Lightning". Belonged to Frederick George CROSBIE VX52187, enlisted in the 2nd AIF on 26.3.1941 age 22 years. At discharge from the Army on 19.12.1945 he held the rank of Pte in the 2/6 Batt AIF. .1) Trench Art. Female figure on map of New Guinea with raised arm holding aloft a model aeroplane. .2) Attached to a wooden lacquered base. The figure and plane are made from aluminium. Map is inscribed "Greetings from New Guinea 1945".trench art, ornaments, metalcraft, handcrafts, souvenirs -
Bay Steamers Maritime Museum
model steam engine
This model was found in the collection of Bay Steamers Maritime Museum. It is not knowt who created it but it is supposed that it was constructed to educate the many masters of the Wattle in the operation of a steam engine - a not so common mode of power these days. A Bay Steamers Maritime Museum examined the model in March 2012 and discovered that is was in poor repair. Using his existing knowledge, and with reference to some historic texts, he made some repairs and returned the model to working order. Here is his anaylsis of the situation as an excerpt from the Bay Steamers Maritime Museum newsletter Steamlines May 2012 "I was confronted with a model of a steam engine used years ago as a training aid for hopeful steam engineers. Already having a knowledge of steam operations, I considered a museum write-up for that model a ‘piece of cake’. However, on turning the model’s crankshaft, the valve timing seemed ‘out of kilter’ with the movement of the piston. Problem was that the two eccentrics on the crankshaft were not properly secured to it. Eventually I fastened the two eccentrics to the crankshaft where I felt that they should be and then realized that one of them had a chain-driven valve-timing device attached. This would be adjusted while an engine was running to achieve best performance and fuel economy whilst in operation by accurately controlling the period of time during which steam under pressure from the boiler would be admitted to the cylinder and give greater time for the steam to expand in the cylinder, move the piston and turn the crankshaft and thus, drive the attached apparatus. When the valves were correctly set up it was then possible to get the model to function properly.The model comprises a green section, which is the actual the model mounted on a brown painted board. There are two parts of the model, painted white representing the steam passages, and black representing the cast- iron portions of the cylinder-block casting, and of the main valve sliding between the cylinder a second sliding valve. Of the black portions, one slides back and forth being connected to a rod which is connected to an eccentric clamped to the crankshaft and is the nearer to the flywheel of two eccentrics. This eccentric is attached to the crankshaft at an angle of 90 degrees to the crank-pin attached to the flywheel. To operate the model simply turn the flywheel by means of the handle attached to its crank-pin. A second eccentric is also attached to the crankshaft, further away from the first eccentric, and it is adjusted to operate 90 degrees from the first eccentric (that is, 180 degrees from the crank-pin) A piston (painted silver) is located in a plastic cylinder and has a piston rod which passes through one end of the cylinder, (in actual practice a steam-proof gland seals the cylinder against loss of steam) terminating in a cross-head slide between four rails guiding it. From this cross-head, a connecting rod joins the piston-rod to the flywheel via the crank-pin attached to the flywheel which is part of the crankshaft. (In actual practice, a flywheel may not be used, particularly in a multi-cylinder engine.) The white portions of the model painted nearest to the cylinder represent the two steam ports cast into the main cylinder block, whilst one section painted in between those two represents the exhaust outlet (which may be connected to a condenser to conserve water, or to the open air). The main slide valve has three white-painted portions painted thereon. It has two white-painted marks representing the steam passages to the steam ports into the cylinder, and a third section in between the other two, being that part of the valve through which exhaust steam passes in line with the ports in the cylinder block. By rotating the flywheel, the operations of an engine will be observed as steam is admitted to the main valve via the gap between the two jaws of two moveable portions of a second sliding valve which is operated by the second eccentric attached to the crank-shaft. This eccentric is used to finely tune the valve timing of this model to obtain best running results of an engine. There are various methods used for reversing a steam engine. model compound steam engine, steam engine, model, crankshaft, valve, flywheel, wattle, engineer, eccentrics -
Wodonga & District Historical Society Inc
Domestic object - Airzone Vacuum Cleaner, 1950
Standard Telephones and Cables Pty Ltd was a telecommunications company that began as part of Western Electric, a telephone manufacturing company set up by Alexander Graham Bell. Following the First World War, Western Electric diversified to include electric generators and wireless receivers, all still imported. In 1925, Western Electric was sold to the International Telephone and Telegraph Company. In Australia, it became known as Standard Telephones and Cables (Australasia) They worked closely the Postmaster Generals department to set up telephone and radio networks throughout Australia. Its first factory was in Chippendale, New South Wales but ut developed to have branches in all stated of Australia. By the end of the Second World War STC was Australia's biggest manufacturer due to its critical role in producing telecommunications equipment, domestic radio receivers, telecom cables, military equipment and electron tubes. The company returned to peacetime manufacture. Rather than reduce staff it used its excess capacity to produce electric irons and other domestic appliances including vacuum cleaners and floor polishers. This model was produced at the beginning of the 1950s. It was once owned by Mr. Stiff from Stiff and Gannon, Wodonga.This item has local and national significance. It was used in a local Wodonga business and is representative of domestic appliances used in the 1950s. It also has national significance as it is an excellent example of good produced by the manufacturing industry in Australia during that period.Model 30 Airzone Vacuum Cleaner and accessories. Manufactured in AustraliaMetal logo for Airzone including engine specificationsdomestic appliances, standard telephones and cables pty ltd -
Mont De Lancey
Decorative object - Horse Dairy Buggy Model, Chas W Davis
The collection of thirteen model horse drawn vehicles were carefully handmade by Mr Chas W Davis 1925 - 2002. He was a talented artist and saw doctor. This model of a horse drawn Dairy Cart replicates the vehicle that enjoyed respect from the public during the 1880 and early 1900's. A model of a horse drawn black open Davis Dairy Buggy or Cart which is a lightweight two wheeled one passenger open horse drawn carriage where the driver sits behind. It has two large gold painted spoked wheels with black rims and mudguards, blue painted seating and gold painted armrests, two gold coach lamps and gold patterned footrest in front of the driver. At the rear are three silver milk cans with two taps to dispense the milk. There are two long brown wooden shafts on each side to surround the horse. It has a model of a brown coloured horse with a black tail and mane, which has the necessary horse tack for carriage use to help the driver communicate with the horse. These carrier carts or vans were two wheeled medium weight Commercial Vehicles.DAVIS DAIRY painted in white lettering on each side of the cart.replicas, models, scale models, vehicles, carriages, horse drawn vehicles, toy horses, early commercial vehicles, milk cart -
Ballarat Tramway Museum
Photograph - Black & White Photograph/s, Keith Kings, 7/10/1956 12:00:00 AM
Black and White print contained within the Wal Jack Bendigo and Geelong Album, see Reg Item 5003 for more details. Photograph of a model of Bendigo tram ESCo 10. .1 - On rear in ink "Model of Bendigo No. 10 - original type, plus vestibules. Maker Unknown, now in possession of KSK. (7/10/56)" Has K.S.Kings stamp in top right hand corner and number "K(i)(6)" trams, tramways, bendigo, models, esco, tram 10 -
Melbourne Tram Museum
Functional object - Model - Cooee N gauge W6 964 - keyring, Cooee Classics Pty Ltd
Diecast and painted N gauge model of a Melbourne W6 or SW6 tram, made in China for Cooee Concepts. Painted in MMTB Colours with a Yarra Trams logo. The individual wheels rotate.Demonstrates the work of the model maker.Diecast painted model of a W6 or SW6 tram - numbered 964 on the ends of the trams, with a Yarra Trams logo. Numbered 955 on the underside. At one end of the object, - tow bar point on the bumper bar is a small extension to allow for the fitting of a key ring. models, cooee concepts, w6 class, trams -
Orbost & District Historical Society
box camera, From 1953 -1957
The box camera is a simple type of camera, the most common form being a cardboard or plastic box with a lens in one end and film at the other. They were very popular in the late 19th and early 20th centuries. A series of film box cameras were made by Kodak Ltd. in England and were made of sheet metal. There were three generations, from 1937-41, 1946-53 and - renamed "Brownie Six-20" - 1953-57. The name "Brownie" was a trademark used by Kodak for an enormous variety of cameras, over an 80-year history.The Brownie cameras were named after the brownies in popular Palmer Cox cartoons. box camera is a simple type of camera, the most common form being a cardboard or plastic box with a lens in one end and film at the other. They were very popular in the late 19th and early 20th centuries.A black box camera, made of sheet metal. A Brownie Six - 20 camera Model E. It has an imitation pigskin covered metal body with two view-finders. It has a a built-in sliding portrait lens for close-ups and a filter for black and white film. It has a 2 pin flash contact and tripod sockets. There is a shutter safety catch. The face plate has a horizontally striped design and the winding knob and shutter release button are plastic. The carrying handle has been replaced by string.On front - Brownie With flash contacts Six-20 Camera MADE IN ENGLAND BY KODAK LIMITED Model E photography camera box-camera kodak- brownie -
Royal Australian and New Zealand College of Obstetricians & Gynaecologists (RANZCOG)
teaching model,foetus, 1940s-1950s
Originally this teaching model belonged to Prince Henry's hospit�l library and was transferred to the Monash Medical Centre, Clayton in the 1970s by Sister Gertrude Berger, a famous nurse-educator, who is best known for her work leading up to the transfer of nursing education in Victoria from hospitals to universities in 1986.Gerty (as she was known in the School of Nursing) bought them in Europe in the late 1940s and early 1950s.Model of a foetus, approximately seven weeks. Painted plastic on metal rod with round wooden stand. Labelled on base "AV618.2 / 01 Fetus/ FOETUS". Stamped on base, "PRINCE HENRY'S HOSPITAL/ NURSES LIBRARY." Label on base"Adam Rouilly/ London England". The model has anaaatomical numberings in black ink. There must have been an acompaning information booklet [missing].teaching model anatomy, female foetus -
National Wool Museum
Book, Knitting, Sirdar leaflet no. 1797
One of a collection of 56 knitting pattern books donated by Mrs Hilma Carruthers. These books had been used by Mrs Carruthers, her mother and her two daughters. This booklet was produced by Sirdar (UK) and contains three knitting patterns for tea pot cosies.Sirdar / No. 1797 / DOUBLE KNITTING WOOL / OR / SUPER NYLON DOUBLE KNITTING / TWO SIZES / 15 / CENTS / 1'6 / MODEL 'A' / MODEL 'B' / MODEL 'C'handicrafts - history knitting, harrap bros. (sirdar wools) ltd, handicrafts - history, knitting -
Federation University Historical Collection
Unknown - Object, Allan Mine Cage Safety Brake, c1873
A mining safety cage was used in a mine lift. It was fitted with mechanisms to prevent the cage from dropping if the lifting rope broke. In the 1870s in Victoria, deaths and injuries from falling cages in vertical shafts of gold mines were a major problem. The inventor of this safety cage was Robert Allan, a machinery maker of Creswick Rd, Ballarat. He said his cage featured a ‘dissolving’ fulcrum. Others called it an eccentric (off centre) system. Note the pair of clutch levers designed to grab the side guides if tension ceases in the suspending rope from the poppet head pulley. Also, the hinged ‘lids’; designed to protect miners trapped in a braked cage from falling rope, and to enable rescue of the miners. This model was presented to The Ballarat School of Mines Council in November 1876. This model was shown at the Smeaton Show in November 1874, Ballarat School of Mines Museum from 1876, and examined by the 1879 Victorian Board of Inquiry (Pg 15 of FedUni Catalogue 3437) From the Argus of 13 November 1874: At Smeaton Show, Robert Allan of Ballarat won 1st prize for a Model of a Mining Cage, a Butter working machine, a Cheese press and a Curd Mill. By 1878 an Allan Safety-Cage was in operation in the Number 6 shaft of the Band and Albion Consols mine in Ballarat. This cage was judged the best inspected by the Victorian Board of Inquiry by 1879, p. 39.Mining was a big industry in Ballarat in the late 1800s and a lot of deaths were recorded because of mining accidents, the development of the mining safety cage brake limited the deaths and injuries from falling cages in vertical shafts. The model also has links to the Ballarat School of Mines, being presented to the council in 1876. Ballarat School of Mines is the oldest Technical School in Australia and is a predecessor of Federation University. The model is significant to Ballarat's mining history.Model of a mine safety cafe. A grey painted wooden frame with metal model of cage and safety brake system. When tension ceases in rope a pair of crutch levers grab strongly onto the wooden guide strips which run down the sides of a vertical shaft. This safety cage was discussed in "Safety Mining Cages. Report of the Board of Enquiry on Safety Cages 1878-9; together with proceedings of the Board and Appendices".safety cage, mine cage safety brake, robert allan, model, safety cage model, machine maker, millwright, mining, gold mining, tools, equipment, victorian board of inquiry -
Lara RSL Sub Branch
Japanese Cavalry Sword, Japanese Model 1899 Cavalry Sword
Japanese Model 1899 Cavalry SwordJapanese Model 1899 Cavalry Sword This Japanese Model 1899 Cavalry Sword has a interesting hilt in that the grip is of wood with a metal backstrap. The wood is probably is very hard, and has been nicely checkered. The checkering continues right through on to the metal backstrap, giving a very interesting effect. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. There is also a screw and spanner that is retaining the grip. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. This Japanese Model 1899 Cavalry Sword has a interesting hilt in that the grip is of wood with a metal backstrap. The wood is probably is very hard, and has been nicely checkered. The pommel is smooth and round, with a spanner type flush mounted nut which most likely acts to retain the tang. The scabbard is a heavy duty steel example which exactly matches the steel used to construct the hilt. The scabbard is perfectly straight throughout, with a single carrying band and ring.A number is stamped near the hilt on the shoulder of the blade " 96982"japanese model 1899 cavalry sword, metal scabbard -
Ballarat Tramway Museum
Letter - from Peter Duckett to Wal Jack re Ballarat Sprinkler car tank, Peter Duckett, 8/3/1958
Wal Jack had an extensive range of correspondents throughout Australia and the world who often prepared extensive notes and records for him. This letter from Peter Duckett, the owner and proprietor of the Model Dockyard, dated 8/3/1955 discusses the water tank on the Ballarat ESCo sprinkler tram and its disposal history, First sold to a Mr Colters of Forest St and then sold to a lady in Invermay. Also compares the Ballarat tank to that of Bendigo. Finishes off with a discussion about his visit to Ballarat the previous weekend and the traffic on the road.Demonstrates some of the correspondence that Wal Jack received from around the world and that of Peter DuckettLetter on The Model Dockyard letterhead, printed quarto sheet, hand written by Peter Duckett dated 8/3/1955 - two sheets.letters, wal jack, peter duckett, sprinkler tram, water tanks, ballarat, bendigo, model dockyard -
Flagstaff Hill Maritime Museum and Village
Instrument - Set Square, 1930-1955's
This set square was used in the planning and making of components for the ship model Sovereign of the Seas. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. James Bernard Williams was known as Jim Williams, born 1888 at The Forth and died 1959 in Warrnambool. He was a passionate ship model builder. Jim left school at the age of 14 years to work at the Don Store in Ulverstone, Tasmania. He played piano at the silent pictures. He enlisted and fought in France along with his two brothers and was wounded there. On return to Tasmania he found it difficult to get employment. He moved to Warrnambool and worked in the menswear department at Cramond & Dickson clothing store, corner of Timor and Liebig streets, until the Depression, when he lost his job. After some time unemployed and working part time until 1932, Jim was employed at Fletcher Jones Menswear in Warrnambool. In 1957 Fletcher Jones invited Jim to write out a list of the most interesting details of the ship model Sovereign of the Seas, with the view of displaying the model and the information for a short time in the factory and then move it to the display window of the Fletcher Jones shop in Warrnambool. Jim worked there for 27 years until just before he died in 1959. His Retirement Speech letter and a Staff Photo from Fletcher Jones are included with the donation. ABOUT JIM’S MODEL MAKING For many years Jim worked on his model ships, including The Endeavour and The Sovereign of the Seas. He had a table set up in a bay window and worked on them on and off using a jeweller's eye glass on the finer pieces. He was a real perfectionist and would re-carve pieces many times until he was happy with the results. This set square is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This set square was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Set square; thin, flat metal blade with rounded corners set at a right-angle into timber stock using three rivets, each with a diamond shaped surround. There is a remnant of red paint on the timber and signs that the set square has been well used. This set square is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”. flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, ship model sovereign of the seas, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, measuring instrument, technical drawing instrument, set square, carpenter’s square, drawing instrument, drawing tool, technical drawing tool, sovereign of the sea, ship model, hobby, ship model tool, english war ship -
Flagstaff Hill Maritime Museum and Village
Craft - Ship Model, H.M.S. Lady Nelson, 1988
This model of the ship H.M.S. Lady Nelson was researched and built as the vessel Lady Nelson by David Lumsden, a professional ship model builder. His Majesty's Armed Survey Vessel Lady Nelson was commissioned in 1799 to survey the coast of Australia. This vessel was purpose-built before the British Admiralty requested plans for a Schooner for Port Jackson. At the time large parts of the Australian coast were unmapped and Britain had claimed only part of the continent. The British Government were concerned that, in the event of settlers of another European power becoming established in Australia, any future conflict in Europe would lead to a widening of the conflict into the southern hemisphere to the detriment of the trade that Britain sought to develop. Against this background, Lady Nelson was chosen to survey and establish sovereignty over strategic parts of the continent. Lady Nelson left Portsmouth on 18 March 1800 and arrived at Sydney on 16th December 1800 after having been the first vessel to reach the east coast of Australia via the Bass Strait. Before that date, all vessels had sailed around the southern tip of Tasmania to reach their destination. Lady Nelson's survey work commenced shortly after she arrived in Sydney, initially in the Bass Strait area. She was involved in the discovery of Port Phillip, on the coast of Victoria, in establishing settlements on the River Derwent and at Port Dalrymple in Tasmania. She also successfully chartered much of the Victorian coastline and was heavily involved with the exploration of the Queensland coast with Matthew Flinders; investigated the Hunter River; made numerous visits to New Zealand and Norfolk Island and was involved in the founding of numerous settlements. In comparison to most colonial vessels, the Lady Nelson was technically unique she was fitted with sliding keels, or centreboards, and water-tight trunks reaching to the deck. Captain Schank invented these sliding keels that, when raised, reduced her draught to less than six feet. Her life as an exploration vessel ended while accompanying HMS 'Tamar' to Melville Island in 1825, the 'Lady Nelson' was captured and later abandoned by pirates off the island of Babar (Indonesia). This brought the vessel's 25 years of coastal exploration and navigation to a close.The Lady Nelson made was the first British ship to survey of the southern or south-western coast of Australia and traverse the Bass Strait. The vessel holds a special place in Australia's history of exploration as the first to explore and establish settlements in the then-new British colony of Van Diemans Land. The model gives an insight into what life must have been like onboard sailing vessels of the time and Australia's early history of establishment and exploration. This model acts as an important legacy of the full-scale ship which no longer survives. Ship model of the 60 ton British brig HMS Lady Nelson. Timber model of a two-masted brig with rigging but no sails, displaying the British Union Jack flag. The ship is in a glass exhibition display case on metal stand. HMS Lady Nelsonflagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, by captain john schanck, sliding keels or centreboards, lady nelson, british brig hms lady nelson, david lumsden ship model builder, lieutennant james grant, bass strait discovery, surveying king island and port phillip bay, philip gidley king -
Tatura Irrigation & Wartime Camps Museum
Hut 4 - Model, Camp Hut
Model made by past internee of Camp 3 A, Lothar Streker. He lived in the hut with his parents, sister and other familiesModel of hut in Camp 3A. Windows and doors painted brown. Behind each door a small room. 6 windows, 3 double doors, 2 steps, front and back. Small red bucket and electric light on one end. No. 4 on both ends of hut. Flower garden all around the huthut, model, streker l, camp 3, tatura, ww2 camp 3, handcrafts, models