Brandt Brothers LampHistoric - Railways - Brandt Brothers LampBrandt Brothers Lamp made of metal and glassBrandt Brothers puffing billy, brandt brothers lamp

The Adlake Non Sweating Lamp "THE ADLAKE NON SWEATING LAMP CHICAGO" Adlake is a shortened name of the "Adams and Westlake" company. They began doing business in 1857 in Chicago. They manufactured railroad supplies and hardware in Chicago. In 1927, they moved to Elkhart, Indiana, where they remain in business today. The difference between "lamp" and "lantern" is that the lamp is meant to be hung on a post or a hook during use and the lantern is hand-held and only used when a person is directing traffic. It has four lenses- two amber and two blue. Adams & Westlake, also known as A&W or Adlake, became a dominant maker of short-globe lanterns and their #200, #250, and plain “Kero” (sometimes known as #300 or #400) models were sold by the thousands to the entire range of railroads. Short-globe lanterns came about because manufacturers figured out how to get a lantern to burn properly with a shorter combustion chamber, which allowed lanterns to be shorter and cheaper. Adams & Westlake began selling #200 Kero lanterns around 1921 and they sold well, the #250 Kero lantern was released in the mid 1920’s as an improvement over the #200 version, with a new burner design. FInally, around 1930 Adams & Westlake released models marked simply “Kero” but are sometimes known as the #300 or #400 models, which are further refinements. The #200, #250, and “Kero” models all look very similar in design and in fact they are all pretty much the same frame design with a couple of minor differences on the later “Kero” models. Short globe lanterns are still very easy to find because they were produced well into the mid 1900s. Adams & Westlake short globe lanterns can usually be dated by looking for a two-part date code on the bottom of the lantern. The first digit will be 1,2,3, or 4 followed by a dash and then a two digit number. Sample code: 2-39 would mean that the lantern was produced in the 2nd quarter (Apr-Jun) of 193Historic - Railways - Adlake Non Sweating LampAdlake Non Sweating Lamp made of metal and glass Metal with handle, painted black, oil Bullseye lens, 13 cm diameter, green Circular lens on opposite site, 5 cm diameter, clear Sliding panel provides access to burner Rain shield embossed 'THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON''THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON'puffing billy, adlake non sweating lamp

Leather Cash Bag - Kyneton Leather Cash Bag – Kyneton Inscriptions & Markings Kyneton Used for transporting money and other valuable items between a location and Kyneton Historic - Leather Cash Bag from Kyneton stationLeather Cash Bag - Kyneton - small Leather BagKynetonkyneyon, puffing billy, cash bag

fittersLeather Tool Bag - Large A leather bag used by the fitter to carry spanners and other tools required for repairs.leather bag used by fitters on the victorian railways Leather Tool Bag - Large made of leather with copper rivetspuffing billy, leather bag, victorian railways, fitter

fitters Leather Tool Bag - Medium fitters Leather Tool BagLeather Tool Bag - (Medium size)made of leather with copper rivets puffing billy, railway fitter, victorian railways, tool bag

vaporizing kerosene gas lamps of this type were used by track gangers to facilitate night works. Historic - Victorian Railways - Permanent Way and Works - track equipment - Ganger's Lamp made of metal, brass and glass V.R ( and Arrow symbol ) AL 14puffing billy, victorian railways, ganger's lamp

NKS Trolley Motor Transporting Box A wooden box used for transporting the engines of the Gangers trolleys between the line in use and the Workshops at Spotswood. Engines were often changed over due to mechanical failure or being required for a service. Rather than send the complete trolley in for work, the engine was removed and transported. These boxes may have arrived at a location with an engine in it, to replace the one returning to the Workshops, cutting down the time that the trolley may have been out of use. Historic - Victorian Railways - Permanent Way and Works - track equipment - NKS Trolly Motor Transporting BoxNKS Trolly Motor Transporting Box - two boxes made of timber with wrought iron fittings puffing billy, nks trolley motor transporting box, trolly, trolley

Rail Bender - Part of Hydraulic Rail Bender Rail Bender – No. 3 Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is tightened slowly using large spanner. Historic - Railways Permanent Way and Works - track equipment - Rail Bender large Rail Bender - Part of Hydraulic Rail Bender made of cast wrought iron puffing billy, rail bender

Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf#zoom=100 gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949. Historic - Railways Permanent Way and Works - track equipment - Motor Spirit Highly Inflamable Transporting Tin ContainerMotor Spirit Highly Inflamable Transporting Tin Container made of tin Motor Spirit Highly Inflamable puffing billy, motor spirit transporting container

Appletons Patent Railway Warning Lamp with Sherwood Style burner Used by Gangers during track work at night Appletons was an early pioneer of railway lamp signal lamp Alfred Edward Appleton invented and patented the Spinner Railway signal lamp in England in 1897. Appleton lamps were patented and manufactured by Alfred Edward Appleton at a factory in Sherwood during the early 1920's to late 50's and widely used throughout Queensland Railways. Alfred Edward Appleton's father was a railway pointsman and porter on the Great Western Railway in Tewkesbury England Historic - Early Hand signalling Lantern Appletons Patent Railway Warning Lamp made of tin & metal and glassAppletons Patentpuffing billy, appleton warning lamp, lamp

Fire Fighting Extingusher Tank Old style firefighting extinguisher, for use on very small firesHistoric - Railways Permanent Way and Works - track equipment - Fire Fighting Extingusher TankMetal Fire Fighting Extingusher Tank with rubber hosepuffing billy, fire fighting extingusher tank

This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill

Kerosene was used to light the signal lamps at night time on a railway, to ensure that a locomotive driver could see that the line was clear there was no danger of another train ahead. This container was used to store the in kerosene to fuel such lamps and was kept inside a lamp room until required for use.Victorian Railways - Keroseane Container Used in the storage of kerosene prior to use in lamps at stations.Large, cylindrical tin container with conical lid and wire handle. A small zinc spout is embedded in the lower quadrant. The word 'KERO' is stencilled in white across the front. Keropuffing billy, kerosene, fuel, combustible material, tin container, lamps

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

Gangers Shed Desk A desk used in the Gang Shed for office work and other associated functions. Historic - Victorian Railways Permanent Way and Works - Gangers Shed Desk Gangers Shed Desk made of wood with wrought iron fittingspuffing billy, gangers shed desk, victorian railways

Ganger's Fire Beater This was used to beat the flames of a fire. They were used by track Gangers when burning off the trackside vegetation, to ensure the fires were kept under control. the canvis was dampened with water before useHistoric - Railways Permanent Way and Works - track equipment - Ganger's Fire Fighting Mop Ganger's Fire Beater made of timber handle with canvas strips attached puffing billy, fire beater

Hand Operated Rail Saw Out on the track in the old days, it was sometimes required to cut a piece of railway track. Before the use of generators and oxy cutting, the only way to do this was with a hand saw. This is the machine operated by two people, that would cut a piece of rail in half. And when the rail was cut, it was usually required to join it to another rail which required putting in 4 to 6 holes in the rail with a Hand Operated drill. Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Saw Hand Operated Rail Saw made of cast metalpuffing billy, hand operated rail saw

Light Rail Bender Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly. Historic - Railways Permanent Way and Works - track equipment - Light Rail Bender Light Rail Bender made out of cast wrought ironpuffing billy, light rail bender

Crank Handle for Saw Bench Crank Handle fornew record Saw BenchCrank Handle for Saw Bench made of cast metal 4N153puffing billy, crank handle, saw bench, new record saw bench

Railway tracks are produced straight. They may appear to be easy to bend and may appear flexible, but are required to be bent for curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this was required to be done with a manual rail bender. Sometimes referred to as a Jim Crow, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly.Victorian Railways Permanent Way and Works track equipment Light Rail Bender narrow GaugeCast iron semi-circular tool, with hooked ends and central screw shaft.puffing billy, rail bender, jim crow

Rail Turning Bar Rail is heavy, sometimes as much as 120 lbs per yard. To assist in being able to move rail, a special turning bar was developed. Usually a long handle, on one end various features in the head allow rail to be moved Historic - Railway Permanent Way and Works - track equipment - Rail Turning BarRail Turning Bar made from cast wrought iron puffing billy, rail turning bar

Ratchet Spanner This spanner is used on track work. Being a ratchet spanner, it allows movement in one direction, with a reverse movement to keep the tool in the same position, but it does not allow the item being tightened to rotate with the spanner in the reverse direction. This allows for longer handles and therefore gives more force to the item that is being tightened or released.Historic - Railway Permanent Way and Works - track equipment - Ratchet SpannerRatchet Spanner made of cast wrought iron puffing billy, ratchet spanner

Metal Pully and Rope When heavy items were required to be moved a rope and pulley set was very handy. By attaching one end of the set to a solid surface, it was possible to lift items. In the bush, the timber workers made good use of the pulleys. When set up in a sequence, they could move logs across gullys, up and down hills as the chopped down trees made their way to a sawmill. Using animal or mechanical power increased the use of the pulley and rope. Historic - Industrial - Metal Pulley and RopeMetal Pulley and Ropepuffing billy, metal pulley and rope

During early farming in Australia (before motorised whipper snippers) the hand held sickle was used to cut long grass, in this case in or around railway tracks. The inside of the blade's curve was sharp, so that the user can either draw or swing it against the base of the grass, catching the stems in the curve and slicing them at the same time. Historic - Railway Permanent Way and Works - track equipment - Grass SlasherWrought iron sickle with extended with wooden handle.puffing billy, extended sickle, farm tool, reaping hook, curved blade, grass cutting

Railway Track Tool Rail is heavy, sometimes as much as 120lbs per yard. To assist in being able to move rail, a special bar was developed. Using the handle as a lever, one section clamps onto the rail, allowing it to be moved. Historic - Railway Permanent Way and Works - track equipment - Railway Track ToolRailway Track Tool made of forged ironpuffing billy, railway track tool

Watering Can A watering can, with a large spout. Its former use is currently no known, but may have been used for oil, chemicals or even sand.Historic - Railway Permanent Way and Works - track equipment - Watering CanWatering Can with a large spout made of tin puffing billy, watering can

Van 8 NUU - Louvered Van Louvred Truck (11) (on u/frame of 110 NQR) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 8.VA - 20/ 7/1906 NWS Built new - / /1926 - To NU 8.VA - NU 8.VA - / 9/1928 - Modified AC Malco 21/12/1953 - Sold (to) Coulston & Hyder RS54/338 Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvred VanWooden Louvered Van on under frame of 110 NQR - Made of Timber on a Wrought iron frame - current condition Untrafficable8NUUpuffing billy, 110 nqr, 8 nuu - louvered van, victorian railways, 2'6" gauge, narrow gauge rolling stock

10NBH Carriage - Excursion Car In Active Service - Belgrave Station Yard NBH SECOND-CLASS EXCURSION CAR. The H was recognising their use for "Holiday" traffic. 15 of these cars were built in 1919 and numbered 1-15. Two more were built in 1981, and numbered 16 & 17. Two extended versions for wheelchair passengers were built in 1981 & 1983. These were numbered 51 & 52 - a separate number series due to the different type of vehicle. Six, numbered 18-23, were built in 1997-98. These had steel frames, padded seats, and a wide "window sill". At first glance they look the same as the previous NBHs. There are other minor construction differences due to the use of steel framing. 18NBH entered traffic 19/4/1997; 19NBH on 5/12/1997; 20NBH on 19/12/1997, the others added in 1998. VR Service History : *NBH 10.VA - 8/12/1919 NWS Built new - /12/1928 - Modified AC Malco BO circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Excursion Car Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock Collection10 NBH Passenger Carriage - Excursion Car made of steel and timber10NBHpuffing billy, 10nbh, nbh - excursion car, victorian railways, victorian railways narrow gauge - passenger rolling stock

Van 2NBC - 1 compartment and van (7 & 4 ton capacity) In Active Service - Belgrave Station Yard NBC COMBINED SECOND-CLASS PASSENGER CAR AND GUARD'S VAN. Six cars, numbered 1-6, were built during 1898-1905 and originally classed NBDBD. The D was previously the letter code for Brakevans/Guard's Vans, but was changed to C when the double-letter code was dropped in 1910. A final NBC numbered 7 was added to the fleet in 1910. VR Service History : NBDBD 2.VA - 3/10/1899 NCL Built new - circa 1900 - Photograph R101: as N2BDBD circa 1910 - To NBC 2.VA - *NBC 2.VA - / 5/1926 - Modified AC Malco circa 1955 - Condemned -Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger and Guard's Van carriage Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection2NBC - Combined Second-Class Passenger Car And Guard's Van. - Made of Timber on a Wrought iron frame 2NBC - 1 compartment and van (7 & 4 ton capacity)2NBCpuffing billy, 2nbc, 2nbc - combined second-class passenger car and guard's van, victorian railways, narrow gauge passenger and guard's van rolling stock, 2'6" guage