Ballarat - Gives details of where purchased from , date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, condition of tram, trolley base, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel base, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and details of advertising space in racks. At base has typed (original) list of trams of the two types, single truckers and bogie trams. List of trams includes the scrubber and No. 20 which was scrapped prior to system closure. See also 3430 and 8722 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Some changes have been made to the tramcars since the preparation of this sheet and there are some errors and differences. See also Reg Item 6879 for an annotated version.Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Typed List (Carbon copy) of tramcars and their details for Ballarat dated 11 May 1961, titled "Numbers and Particulars of Trams". Two sheets which have been taped together. tramcars, ballarat, equipment, lists, data

Ballarat - Gives details of where purchased from , date of purchase, type, body builder, seating capacity, overall length, overall height, overall width, condition of tram, trolley base, Lightning arrester, controller make and type, Truck Maker and type, type of truck, axle type, wheel base, axle diameter, motors type and maker, Motor horsepower, Armature bearings, suspension bearings, gear teeth, Air compressor make and type, Brake Valves make and type, Governor make and type, Weight in tons and details of advertising space in racks. At base has typed (original) list of trams of the two types, single truckers and bogie trams. List of trams includes the scrubber and No. 20 which was scrapped prior to system closure. See also 3430 and 8721 for other versions - different dates and 8690 for a Bendigo list. Note: Framed copies of both Ballarat and Bendigo are held in the depot. Some changes have been made to the tramcars since the preparation of this sheet and there are some errors and differences. See also Reg Item 6879 for an annotated version.Yields information about the dimensions and equiipment on Ballarat Tramcars operated by the SEC.Dyleline print of a typed List of tramcars and their details for Ballarat dated 5 September 1966 (typed on), titled "Numbers and Particulars of Trams". tramcars, ballarat, equipment, lists, data

11NBHC Passenger Carriage - Excursion Car and Guard's Van Excursion Car 11 NBH which has been converted by the addition of a Guard's Van compartment by Puffing Billy Railway and re classed & numbered 11 NBHC The NBHC is a conversion from the standard NBH. This was a temporary, but long term, conversion to overcome lack of suitable guard's vans on the Puffing Billy railway. One end of a standard NBH had windows and a hand brake fitted. A padded seat replaced the standard back to back seating, and a partition separated the guard from the passenger compartment. VR Service History *NBH 11.VA - 8/12/1919 NWS Built new - / 1/1929 - Modified AC Malco BO circa 1955 - Condemned - Puffing Billy Service History or Notes Body Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Height 9 feet 2 inches (2794 mm) Weight 8 tons Capacity 22 passengers Number Built 1 In use 1 Historic - Victorian Railways Narrow Gauge - Passenger Rolling Stock: Passenger Carriage - Excursion Car 11 NBH which has been converted by the addition of a Guard's Van compartment by Puffing Billy Railway and re classed & numbered 11 NBHC 11 NBHC - Passenger Carriage - Excursion Car and Guard's Van made of wrought iron and timber11NBHCpuffing billy, pbr, rolling stock , 11 nbhc, victorian railways, passenger carriage - excursion car and guard's van, 11nbh

Set of 15 photographs of the operation of the BTM Horse Tram No. 1 in Wendouree Parade on 3/2/2002. Taken by Peter Winspur on Kodak Paper. All have printed labels on rear with photograph details. Note tram number in photo labels is given as 14, not 18 as actually used. 2011.1 - horse tram ready to depart depot with 26 and 33 in the background. Horse - "Bear", Reinsman - Reg Smith. .2 - Horse tram at the loop .3 - ditto .4 - ditto with 18 on other track at loop. .5 - ditto .6 - ditto, Roger Salen .7 - ditto, ready to depart .8 - Heading towards St. Aidans Drive .9 - at St. Aidans Drive .10 - ditto .11 - ditto .12 - ditto .13 - returning to Loop .14 - ditto, with Len Millar at the Brakes .15 - ditto, approaching Loop with 18 in the background.See abovehorse trams, wendouree parade, gardens loop, tram 1, tram 18

Digital image of a BTPS training / qualification day held on 28/11/1976, at East Preston depot: From left: Richard Gilbert, Peter Hill, Paul Nicholson, Bruce Davey and Jack Chadwick standing between trams 16W (the only tram at the time on the MMTB network with a manual lap brake) and Z16. Peter Winspur advised 18/5/2020: Paul was an M&MTB driver at the time. Peter Hill would have been doing his first day and Jack Chadwick qualified as driver on that day along with Paul. We managed to train Peter in a few weeks as he was back on 19 December! Just in time for the summer running. Inspector Bruce Davey was the trainer/instruction/examiner driver. Image supplied by Paul Nicholson 17/5/2020. See Reg Item 7775 for a photo of just the two cars.trams, tramways, btps, training, z class trams, east preston, mmtb, tram 16w, tram 16

A double deck horse drawn tram with single saloon. drop ends, stairs, longitudinal seats, sliding doors, wheels of cast iron, hand brakes - see notes. Originally built by Duncan & Fraser in 1887. Rebuilt by BTPS 1991. From the BTM Fleet page on the website: Built in 1887 by Duncan and Fraser for the Ballaarat Tramway Company Ltd. as a double-decked horse tramcar. One of eight cars which ran as trailers behind electric trams at times of heavy patronage, after takeover and conversion of the horse lines by the Electric Supply Company of Victoria Ltd. in 1905. Withdrawn in the late 1920's when the body shell became a residential outbuilding locally, until retrieved in 1985. Fully reconstructed to its original form and placed on a modified Melbourne saloon cable car truck. See attached notestrams, horse trams, tram 1

Newspaper clippings titled: “App to curb crowding on public transport” by Timna Jacks Newspaper clipping from the Age 6/10/2020 Trial of new technology designed to encourage social distancing on public transport for buses and trains. Article also refers to government announcement on proposed spending on tram rolling stock. $26M to be spent on life extension works for A and Z-class trams. Works will maintain electrical, braking and traction systems on trams running on 17 routes across Melbourne, about 1/3 of the city's fleet. Government has ordered 50 E-class trams since 2015, with 89 of total order of 100 trams now in use. 111 Z-class 3 trams and 69 A-class trams are still in use. PTUA spokesman Daniel Bowen comments on need for maintenance of older trams and calls for newer, air conditioned trams.trams, tramways, a class, e class, z3 class, myki, ptua, covid-19

Yields information about the drawings that were used by the depot or workshop staff as reference drawings. Has a strong association with the depot workshop staff. Yields information about equipment on Ballarat tramcars and Signalling.Folder containing 46 blueprints or Dyeline prints of SEC tram equipment drawings. Front of folder made from a cloth back sheet of paper extended to secure to a thick cardboard runner. Rear of folder made from an old tram advertising panel or cardboard sheet, cut to size and secured to a thick cardboard runner with a cloth backing on both sides. Sheets secured with three brass screwed clips. Front cover damaged in bottom right hand corner. Rear cover breaking apart on outside around cloth binding. Heavy dirt marks from “grease” on bottom half of rear cover. Contains 46 drawings which have been individually catalogued and numbered on the rear of each drawing within the folder. Some of the drawings have been folded. Reg Item Micro Film No. Old BTPS No. SEC Drawing No Title 4807 42/4 1 VB4/8103C Westinghouse T1F Controller Main Cylinder Segments. 4867 47/2 2 BA-T8-8128 Westinghouse 225N Motor Case Bolt 4830 22/3 B 3 BA-T7-7666 Half Ball Brake Hanger Link, Driving Wheel, Brill Maximum Traction Truck 22E 4868 44/3A 4 BA-T8-8113 Split Suspension Bearing for Type W225 Motor (Westinghouse) 4869 52/2 5 BA-T8-8158 Contact Tips for G.E. Compressor Controller 4818 52/3 6 BA-T8-8159 GE B-23 Contact Finger Tips for G.E. Type ‘B’ Main Cylinder 4870 6/1 7A BA-T3-6734 Brass Nut for Switch Mechanism 4829 6/2 7B BA-T3-6735 Tongue Clip Link for Switch Mechanism 4871 6/3 7C BA-T3-6736 Fulcrum for Switch Mechanism 4872 6/4 7D BA-T3-6737 Plunger for Switch Mechanism 4832 7/6 8 BA-T3-6754 Pivot for Switch Mechanism No numbers 9 or 10 4873 17/5 11 BA-T7-7639 Detail of Motor Pinion for Brill Cars 4831.2 21/4 B 12 BA-T7-7661A Half Ball Hanger Links – single bogie trucks 4874 21/6 13A BA-T7-7663 Axle Box Inner Spring Driving Wheels Maximum Traction Truck 22E 4875 22/1 13B BA-T7-7664 Axle Box Outer Spring Driving Wheels Maximum Traction Truck 22E 4876 22/2 14 BA-T7-7665 Body Spring Brill Maximum Traction Truck 22E 4830.2 22/3B 15 BA-T7-7666A Half Ball Brake Hanger Link Driving Wheel Brill Maximum Traction Truck 22E 4877 22/4 16 BA-T7-7667 Body Spring, Brush Maximum Traction Truck 22E 4820.2 22/6 A 17 BA-T7-7669 Wear cups for Half Ball Brake Hanger Links, Single & Double Bogie Trucks 4878 50/5 18 BA-T8-8149 Connections of Line Breaker and Ratchet Switch for use with Drum Controller 4879 74/6 19 BA-T13-8757/9 Signal boxes, Back of Panel Wiring and External Connections 4880 45/1 20 BA-T8-8116 Trolley Harp 4806 15/3 21 BA-T7-7625 Equalizing Lever, Fulcrum, Brill 21 E truck 4881 15/5 22 BA-T7-7626A Brake Beam Fulcrum Brill 21E truck 4808 16/1 23 BA-T7-7628 Pinion Remover, GE 201G and GE 202 motors 4882 16/3 24 BA-T7-7630 Spring Posts, Brill 21E Truck 4883 21/3 25 BA-T7-7660 Brake Shoe Holder, Driving Wheel, Maximum Traction Truck Brill 22E 4884 21/5 26 BA-T7-7662 Brake Rod Guide, Single Bogie Trucks 4885 22/5 27 BA-T7-7668 Brake Shoe Holder, Pony Wheel, Maximum Traction Truck Brill 22E 4809 42/2 B 28 BA-T8-8101 Trolley Wheel and Axle 4815 42/1 B 29 BA-T8-8102A Motor Suspension Bearing, GE 202 Motor 4796.2 42/5 30 BA-T8-8104 Connection Diagram WH 225N Motor 4886 42/6 B 31 BA-T8-8105B Motor Suspension Bearing, GE 201 Motor 4797.2 48/6 32 BA-T8-8137 WH T1F Controllers 4816 49/2 33 BA-T8-8138 Connection Diagram GE 202 Motor 4887 49/3 34 BA-T8-8139 Connection Diagram K-36-J Controller 4888 50/3 35 BA-T8-8146 GE K-36-JR Controllers, with line breaker (Connection diagram) 4889 50/6 36 BA-T8-8150 Commutator for Westinghouse 225N Motor 4846 51/1 37 BA-T8-8151A Armature Bearing Lining, Commutator End, Type GE 201G Motor 4813 51/2 38 BA-T8-8152 Armature Winding Diagram Westinghouse 225 Motor 4840.2 51/40 39 BA-T8-8154A Armature Bearing Lining, Pinion End, Type GE201G Motor 4890 51/6 40 BA-T8-8156 Armature Bearing Lining, Pinion End, Type GE202A Motor 4891 52/1 41 BA-T8-8157A Armature Bearing Lining, Commutator End, Type GE202A Motor 4892 64/5 42A BA-T9-8392A Step Hangers, Single and Double Bogie Trucks, Hinged Type 4785.2 64/6B 42B BA-T9-8392/1A Step Hangers, Single and Maximum Traction Trucks, Fixed Type 4812.2 43/1 43 BA-T8-8106B GE K36J Controller, Main Cylinder Segments 4893 50/2 44 BA-T8-8145A GE B23E Controller, Main Cylinder Segments 4816 65/2 45 BA-T9-8394B Door Lock for Motorman’ Cabin Maximum Traction Trucks. 4810 73/3 46 BA-T13-8757 Ballarat Electric Tramways Signalling System, Arrangements & Details of Box.On front cover of folder, "1 - 46"trams, tramways, drawings, ballarat, sec, depot, workshops

This item was whittled as a continuous piece from a broomstick handle by George Lynch. George had a long career with Victorian Railways. The son of a railway man, George grew up in St Arnaud near the railway line. He watched the engines go by and dreamed of being an engine driver. He started working as a cleaner in 1907. Through hard work and further study, George worked his way up to become a locomotive driver. He moved to Wodonga in 1917. At the Victorian Railways Institute examinations, George won four gold medals for Engine Working and Westinghouse Brake In 1925 he was appointed as an Instructor. George was one of four senior drivers who in rotation drove the Sydney Limited. The other drivers were Ray Murphy, F. Hobbs and George Padgett. They all lived with their families in Wodonga. George drove the first Spirit of Progress from Spencer Street to Albury. He made railway history in 1937 when the Sydney Ltd ran non-stop from Albury to Spencer Street in 3 hrs. 25 mins, clipping 25 minutes off the previous record. He retired at the age of 65 in 1953 and died at the age of 74.This item is significance because it was made by a long-serving locomotive driver based in Wodonga.A chain made by whittling the handle of a broomstick. It is one continuous piece of wood with a variety of shapes swivels and interlinked sections. There are 13 similar sized links and 2 larger ones. The larger links have small balls inside them.whittled objects, george lynch, railways wodonga

Black and white photograph of cable trailer 88 being loaded onto a wagon at the Spencer St / Flinders St railway yard by the railway yard travelling gantry crane. Trailer lettered M&MTB. Has a man riding the top of the car before being loaded into a I type open wagon. Photo mid to late 1920s? Photo from the Collection of the Department of Infrastructure now with the Public Records Office - image number "Box 108-1. Note: this photo is now out of copyright and may not have been an original VR photograph, but one copied from another source and collected as their Heritage series. The building in the background in Flinders Street (extension/west.) is the former Melbourne Harbour Trust Officers. By the time of this photo was taken the building was in the hands of the Department of Agriculture. Their name can just be seen on the top part of the building. It was demolished when the convention centre was built beside the WTC in the mid-1980’s. The crane was dismantled in the late 1990s around the time of the No 1 goods shed was moved to Bylands. The cable car has been stripped of a number of parts : Some windows. All the brake rigging and pawls All the roof-mounted destination boxes. The wheel skirt.Shows how redundant cable trams were sold and transported to country locations.Photograph - Black and White - Loading cable car trailer 88 at Spencer StHas Department of Infrastructure copy right stamp on rear and number "Box108-1" in ink on rear and "1-8"tramways, trams, cable trams, flinders st, sale of trams, railways, tram 88

Yields information about the condition of the collision between the scrubber tram and No. 26 in Wendouree Parade and the parties involved during Feb and Mar. 1936.Set of two cuttings and text extracts of the reports of the collision between the Ballarat scrubber and tram No. 26 on Wed 5 Feb, 1936. Both extracts and texts down loaded from the National Library Trove Website. .1 - report in the Melbourne Herald, reporting on the inquest into the death of nurse Elizabeth Clarke - titled "Ballarat Trams in Fatal Collision - no warning bell heard says woman passenger", giving details of the accidents, statements of witness Lilian Oliver, Alfred Forte (SEC track assistant), Albert Mawby traffic superintendent, quizzed by Constable Shields re track brakes, Frederick Thompson (Driver of 26). Drivers represented by Mr. Dooley. .2 - report in The Argus 6-2-1936 about the accident - "Woman Critically Injured - accident in Ballarat - Drivers jump for lives", reporting on the event, giving names of those involved, injuries, including the name of the scrubber driver John Tucker, and another passenger Miss Walsh.accidents, collision, scrubber tram, coroners inquests

Magazine cutting or photocopy of an article titled "Trams to Replace buses in Melb's Bourke St Lines", from the September 1943 issue of Truck and Bus Transportation. Quotes MMTB Chairman Mr Bell, Premier Mr. Dunstan. Notes problems with the extra war time traffic, not coping with maintenance issues, problems with double deck passengers, passengers not wanting to use upstairs, trams superior for the short haul, Fisherman's Bend services, number of buses and that the Board is building new trams, the SW6. Notes service schedules to Northcote, could operate Bourke St with 55 trams instead of 74 buses. Notes the work to consider replacement done by Mr. Simpson, the Acting Manager. Has photo of Mr Bell and the exterior and interior of an SW6 class tram. Has adverts for General Motors Holdens making bomber parts, Better Brakes and Hastings Deerings. 2nd copy added 8/4/2021trams, tramways, bourke st, sw6 class, buses, double deck buses, conversion, northcote, services, general motors

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel glass replacement lens for a navigation side lamp of a ship. W.T.G (S) and 10x7 S.STR.ENGL.125warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel glass replacement lens for a navigation lamp of a ship. None warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel glass replacement lens for a navigation mast headlamp of a ship. Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel round glass masthead replacement lens for a navigation lamp of a ship. Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel glass lens for a ships masthead navigation lamp. Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

A Fresnel lens is a type of composite compact lens developed by the French physicist Augustin-Jean Fresnel (1788–1827) for use primarily in lighthouses.  Made from high-quality glass Fresnel lenses were used originally in lighthouses and later for many other applications They were later being used for automobile headlamps, brake, parking, and turn signal lenses, and many other applications. Fresnel lenses used in lighthouses were considered state of the art from the late 19th through to the middle of the 20th century. The subject item is a Fresnel replacement lens used in a ships navigation light. For lighthouses, these lenses have now been replaced with much less expensive and more durable aerobeacons, which themselves often contain plastic Fresnel lenses. The lens design allows the construction of lenses of large aperture and short focal length without the mass and volume of material that would be required by a lens of conventional design. A Fresnel lens can be made much thinner than a comparable conventional lens, in some cases taking the form of a flat sheet. The simpler dioptric (purely refractive) form of the lens was first proposed by Count Buffon and independently reinvented by Fresnel. The catadioptric form of the lens, entirely invented by Fresnel, has outer elements that use total internal reflection as well as refraction; it can capture more oblique light from a light source making the light visible from greater distances.The subject item at this time cannot be associated with a historical event, person or place, provenance is unknown, the item is a replacement for a ships navigation light and it is believed to have been produced before 1950.Fresnel glass replacement lens for a navigation side lamp of a ship. Nonewarrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fresnel lens, maritime light, ships navigation light, augustin-jean fresnel, lighthouse lenses, lighthouse, navigation, warning light

Book titled "The Electric Tramcar Handbook written by W.A. Agnew. Book has dark red cloth covers, gold block titled on front only, with tipped in end papers, title page, contents pages, three introductory pages by author, 127 pages of text, five index pages and six folded sheets interspersed in book with wiring or controller diagrams. Book finished with red tinted edging. Book published by The Electrical Review Limited, London in 1920, 8th edition. On inside end paper, has ESCo Ballarat office stamp with date 30/9/1924, a glued in white sheet of paper with handwritten notation "To be returned to Mr. P. Bath Motorman No. 51, City Office 9.1.63" and on bottom left hand corner a "Tait Book Co. 90 William St. Melbourne" label that has also been glued in. Primary contents chapters include: The Electric Circuit Electric Tramways Electric Tramcars Controllers Brakes On the Road Faults and Breakdowns. See above for inside end paper.trams, tramways, tramcars, tramways, technical books, handbooks

The collection of thirteen model horse drawn vehicles were carefully handmade by Mr Chas W Davis 1925 - 2002. He was a talented artist and saw doctor. This model of a two horse drawn enclosed Hansom Cabriolet replicates the vehicle that enjoyed respect from the public from c.1833 until 1935. A model of a black enclosed coach which is a four wheeled passenger horse drawn vehicle where the driver sits at the front behind the two white horses. It has two large and two smaller gold painted spoked wheels with black rims and gold mudguards on the rear wheels, two gold painted coach lamps, red vinyl padded seating and four open windows with rolled up blinds. There are two doors with a step for easy access into the coach. A long brown wooden shaft separates the horses as well as the necessary horse tack for carriage use to help the driver communicate with the horses. A hand operated brake pad is on the rear wheels. The first Hansom Cabs were clumsy, dangerous awkward vehicles. The drivers were suspected of 'Rude Bohemia'. It took the refinement of Joseph Aloysius Hansom himself to clear airs and remodel the cab to a safe vehicle. It enjoyed respect from c.1833 until 1935. It came in four types.replicas, models, scale models, vehicles, carriages, horse drawn vehicles, toy horses, road transport, coaches

Radio transcript - 12 foolscap sheets, typed. Although not named, appears to have been prepared for or by Mr. Strickland describing "inside information regarding tramcars". Notes cable trams, conversion, sale of trailers and dummies or grip cars, the variety taken over from the trusts, design of new cars (180 in service at the time of the report), open cars vs closed cars, seating and standing capacity, speed, braking system, step heights, destination signs, lifeguards. Gives a description of Preston Workshops, finishing soon, description of the tramcar construction, roofing, painting, sourcing of materials, timbers, cost per tram of 3250 pounds, depots, breakdowns, overhauls, workshops, collision repairs in 1925, construction of 10 safety cars. Vicsig.net gives that X1 461 entered service in Sept. 1926. Pinned to the file by Robert on the rear of TMSV Raffle ticket is a note "Electrical Engineer 15/7/26 p35 "C. H. Wickham gave recent address broadcast on 3LO"In blue pencil in top left hand corner appears to be "Wickham"trams, tramways, tramcars, preston workshops, new trams, sale of trams, cable trams, destination roll, tram brakes, tramcar equipment, x1 class, w class, depots, radio stations

Comb bound (white plastic) specification or tender document, approx. 70 pages, with glossy card covers, titled "Tender Schedule for All-Electric Trams", published by the Melbourne and Metropolitan Tramways Board, closing 12 September 1966. Details the conditions of tender, conditions of contract, notes, specification, gives background information about Melbourne, dimensions, performance, drivers and conductors, trucks, wheels, brakes, electrical equipment, control panels and drawings. The drawings give a map of the system, typical city route, Glenferrie Road route (grade diagram), concrete track construction, min. radius curves, loading gauge, all-electric tram and mounting details for the trolley base, schedule of prices, tender form, form of contract, schedule of information to be provided by the tenderer. Second copy from same donor added 9-3-2017 See Reg Item 2266 for the 1972 version and 4667 for a draft version - dated June 1965. See Item 4388 for the Z3 document. See Reg Item 4049 for associated newspaper cuttings.In red felt pen on top right hand corner "(1966)". Has stamp "Discarded from PTC Library 22 Oct. 1989" on front cover. 2nd copy has "1966" in ink in top right hand corner.trams, tramways, specification, tenders, z class, mmtb, melbourne

The auto tow launching mechanism was designed by Ray Jamieson of Cobram in the north of Victoria. The prototype was built the for the Corowa Gliding Club where it was used for some years. After Ray’s brother, Bert Jamieson, had witnessed the machine in use at Corowa, at Bert’s request, Ray built second one (the Museum’s exhibit) for use at Bacchus Marsh airfield. Bert lived in Melbourne at the time and was a member of the Victorian Motorless Flight Group (VMFG) which used Bacchus Marsh airfield. This occurred in the 1970s. The method of operation was to have the auto tow mechanism mounted in the back of a utility motor vehicle. The launching cable was attached to the glider. With the Volkswagen engine of the mechanism running, the tow vehicle would then drive along the runway to commence the launch. The mechanism would automatically apply brake pressure to the cable drum as the vehicle proceeded freely letting out the cable and then smoothly towing the glider into the air. When the launching cable reached a certain angle, the pilot would release the cable from the glider at which point the winching mechanism would automatically retrieve the cable in preparation for the next launch. This allowed quicker restarts and the flexibility of easily changing runways to suit the wind conditions. It made gliding a simple and cost-effective operation. Ray Jamieson and his son often used the prototype which they named “George” at Corowa in this way. With the exception of several demonstration launches, the Museum’s example of this type of device was not used by the VMFG at Bacchus Marsh due to rulings by the Department of Civil Aviation encouraging the use of aero tow launching at their site. As far as is known this is the only device of its type in the world and is indicative of the ingenuity found amongst the Australian gliding fraternity.Single drum and motorized drive mechanism mounted on a mobile steel frame.australian gliding, glider, sailplane, auto towing, launching, jamieson, corowa gliding club, victorian motorless flight group, vmfg

Ash Wednesday Veteran This Bedford M Series tanker spent its working days at the Forests Commission depot at Gembrook, and among its many forays, fought the deadly Ash Wednesday bushfires at nearby Upper Beaconsfield and Cockatoo on 16 February 1983. Earlier in 1975, the M Series tankers underwent a design change at the Altona North workshops, replacing the cylindrical water tank with a “V” bottom 4090 litre water tank that sat low between the chassis rails to reduce its centre of gravity. Aluminium heat shields were also added to protect the pump operators on the back. While generally considered "bulletproof" the petrol fuel lines on this particular model were very prone to vaporise in the heat causing the motor to stall, often at the most dangerous moment.... in this case frightening the hell out of its driver, affable knockabout bloke, and firefighting legend Lex Wade. Some jokingly said this design quirk was an inbuilt safety feature to stop crews getting too close to the fire in the first place. The Gembrook tanker was later sent into the workshop and all its brake and fuel lines fitted with heat resistant lagging. Fortunately, this remarkable bushfire survivor was rescued from the scrap heap by Lex and fire equipment wizard Barry Marsden upon its retirement from a loyal and lengthy service. After a lick of fresh paint and most of its battle scars "buffed out", this time-honoured veteran now takes pride of place at the Altona North workshop.Bedford M series fire tankerMZF 347fire pump, fire tanker, forests commission victoria (fcv)

One of a few service vehicles built from almost new by the MMTB rather than being a converted vehicle. Donated to the BTM in 1999 and has been an operational tram 2001.Single truck (4 wheels), special purpose tram fitted with two cabs, control equipment, air brakes, track scrubber or cleaning equipment, pump, water and air lines to clean track. Carries approx. 4 cubic metres of water. The tram was built by the Melbourne and Metropolitan Tramways Board in 1934 using the cabs from a C class tram (No. 32). It was transported to the isolated Footscray system a number of times to clean the rails there. In 1961 it received additional body bracing and repainted in the diagonal black and string (light cream) stripes. The tram became 8W during 1975 as the then new Z class trams came into service. By the early 1990's the need for the tram and the other similar cars used to "scrub" the surface of the rails was no longer. The tram was stored at Malvern depot for many years before being donated to the Ballarat Tramway Museum by the Public Transport Commission in September 1999. It has been scrubbing the rails in Ballarat since March 2001. For a detailed article see April 2008 issue of Fares Please. Photo Warren Doubleday 20/9/2008 after painting completed See Destination CityMMTBtrams, scrubber tram

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.George Lynch had a long career with Victorian Railways. The son of a railway man, George grew up in St Arnaud near the railway line. He watched the engines go by and dreamed of being an engine driver. He started working as a cleaner in 1907. Through hard work and further study, George worked his way up to become a locomotive driver. He moved to Wodonga in 1917. At the Victorian Railways Institute examinations, George won four gold medals for Engine Working and Westinghouse Brake In 1925 he was appointed as an Instructor. George was one of four senior drivers who in rotation drove the Sydney Limited. The other drivers were Ray Murphy, F. Hobbs and George Padgett. They all lived with their families in Wodonga. George drove the first Spirit of Progress from Spencer Street to Albury. He made railway history in 1937 when the Sydney Ltd ran non-stop from Albury to Spencer Street in 3 hrs. 25 mins, clipping 25 minutes off the previous record. He retired at the age of 65 in 1953 and died at the age of 74.railways wodonga, fred rochow, wodonga railwaymen, george lynch snr

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Engine Instructor Geoff Williams walking beside Locomotive 1329 to lift the hand brakes. The T class were a class of diesel locomotives built by Clyde Engineering, Granville, NSW for the Victorian Railways between 1955 and 1968. Locomotive T329 was part of the first order completed and entered service in June 1956. At that time, they became the most numerous diesel loco in Victoria. In 1984, the 13 first series T class locomotives were sent back to Clyde Engineering Plant at Somerton in Victoria for a complete rebuild after which they became the P class numbered P11 to P23. This included locomotive T329 which became Locomotive P12. The P Class have proven to be a reliable and dependable class, seeing service across the state in both passenger and freight duties. They often operated in push-pull mode, with a locomotive at each end of the train. The P class locomotives ceased being used for regular passenger operations in November 2012. Although locomotive P12 (T329) is primarily in storage it is still operational and can be hired for special events and as recently as 2017 was also used as an infrastructure maintenance train.At top of train between headlights "T329" In centre Victoria Railways logo "VR"fred rochow, victorian railways wodonga, locomotive 1329

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Fireman Ian Sandford on steps of Locomotive T329. He is moving into position to apply the hand brakes. The T class were a class of diesel locomotives built by Clyde Engineering, Granville, NSW for the Victorian Railways between 1955 and 1968. Locomotive T329 was part of the first order completed and entered service in June 1956. At that time, they became the most numerous diesel loco in Victoria. In 1984, the 13 first series T class locomotives were sent back to Clyde Engineering Plant at Somerton in Victoria for a complete rebuild after which they became the P class numbered P11 to P23. This included locomotive T329 which became Locomotive P12. The P Class have proven to be a reliable and dependable class, seeing service across the state in both passenger and freight duties. They often operated in push-pull mode, with a locomotive at each end of the train. The P class locomotives ceased being used for regular passenger operations in November 2012. Although locomotive P12 (T329) is primarily in storage it is still operational and can be hired for special events and as recently as 2017 was also used as an infrastructure maintenance train.At top of train between headlights "T329" In centre Victoria Railways logo "VR"fred rochow, victorian railways wodonga, locomotive 1329

Comb bound (white plastic) specification or tender document, approx. 180 pages, with glossy card orange covers, titled "Tender Schedule for Electric Trams" and "Contract 3000". Compiled and published by the Melbourne and Metropolitan Tramways Board, closing Monday 10 May 1977. Details the conditions of tender, conditions of contract, notes, specification, gives background information about Melbourne, dimensions, performance, drivers and conductors, trucks, wheels, brakes, electrical equipment, control panels and drawings. The drawings give a map of the system, typical city route, Glenferrie Road route (grade diagram), concrete track construction, min. radius curves, loading gauge, all-electric tram and mounting details for the trolley base, schedule of prices, tender form, form of contract, schedule of information to be provided by the tenderer. Includes an Alphabetical Index. Includes a drawing for a single ended version of the tramcar. Became the Z3 class. Only the table of contents and the drawings scanned. See Reg Items 1583 and 2266 for other similar documents. See Reg Items 337 and 338 for a report on the operation of single ended tramcars 2 copies held.Has in ink written on front cover "J Armstrong" with a stamp blacked out and other copy of the same signature.trams, tramways, z3 class, specification, tenders, mmtb, melbourne, single ended tramcars