A meat grinder or mincer was used for mincing or fine chopping of raw or cooked meat, fish, vegetables or similar food. It replaced tools like a mincing knife.A cast iron mincer with a wooden handle attached to the long cast iron handle. It can be screwed to a table or bench, secured tightly by a two pronged claws. It has a funnel at the top for the meat to be pushed into the mechanism which when the handle is turned operates the inner mechanism which forces the minced meat out through a side opening. The cast iron handle is curved. There are three mincing attachments tied with string.'UNIVERSAL' is stamped on the top of the mincer. Stamped on the front side of the handle - ' L.P. F&C. NEW BRITAIN. CONN.U.S.A.' On the inside of the cast iron handle is stamped - 'PATENT 10.2.1897. PATENT.MAY 15.1900. 4.18. 1890...... and several other numbers which are difficult to decipher.domestic objects, kitchen equipment, cooking equipment, meat grinders, meat mincers

A soldering iron is a hand tool used in soldering. It supplies heat to melt solder so that it can flow into the joint between two workpieces. The iron was heated over a fire or in a charcoal brazier. Soldering irons were primarily used by tinsmiths and coppersmiths to work with thin sheet metal. These hand soldering irons have been replaced by electric ones.Used by coppersmiths and tinsmiths and workers in the Kiewa Valley.The soldering irons have a wooden handle, an iron rod and are made of copper at the pointy end (the bit).shaped like a pyramid.soldering iron, hand tool, coppersmith, tinsmith

Mrs Potts Sad Iron Set . This double point design with detachable handle was patented in the United States of America by Mary Potts in 1871. It was sold in sets of three bodies with one handle and a stand or trivet. The detachable insulated handle was designed to always remain cool for ironing. The handle was detachable, so that several irons could be on the stove at one time and the handle swapped between several bodies. This item is an example of an invention that was universally adopted to make the task of ironing safer and more efficient.A set of double pointed flat irons which detachable handle. This set includes a trivet to rest the unused iron on. All components are made from cast irondomestic appliances, flat irons, sad irons, mrs potts irons

Polishing irons were used for ironing collars and frills. Historical information Sad-irons (the term comes from an old word sald for solid) were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. A solid piece of cast iron, the base is triangular a shape with an eight centimetre base with curved sides coming to a point 13 centimetres from the base and is three and a half centimetres Thick. The bottom of the iron is curved. Two curved pieces two and a half centimetres wide, half a centimetre thick and six centimetres apart rise from rise up seven centimetres, between them is a two centimetre diameter and nine centimetre long hollow handle. Embossed on the iron is - 4 SILVESTERS PATENT SALTER and an arrow with a knotted rope around it. K13polishing iron, silvesters patent, sad iron

A meat grinder or mincer was used for mincing or fine chopping of raw or cooked meat, fish, vegetables or similar food. It replaced tools like a mincing knife.A vintage cast iron mincer with a wooden handle attached to the long cast iron handle. It can be screwed to a table or bench, secured tightly by a two pronged claws. It has a funnel at the top for the meat to be pushed into the mechanism which when the handle is turned operates the inner mechanism which forces the minced meat out through a side opening. The cast iron handle is curved.'2 UNIVERSAL' is stamped on the front of the mincer. Stamped on the front side of the handle - ' L. F&C. NEW BRITAIN. CONN.U.S.A.' On the inside of the cast iron handle is stamped - 'PATENT 12 1897. PAT.MAY 15.1909. 4.18. 1899. D.R.ENG 10'...... and several other numbers which are hard to decipher.domestic objects, kitchen equipment, cooking equipment, meat grinders, meat mincers

Sad irons, also called flat irons or smoothing irons, are shaped pieces of metal that are flat and polished on one side and have a handle attached to the other, created for the purpose of ironing fabric. “Sad” is an Old English word for “solid,” and the term “sad iron” is often used to distinguish the largest and heaviest of flat irons. They often had a trivet on which to rest the hot iron. These irons are representative of domestic appliances used prior to the advent of electricity in the home.A pair of triangular flat irons. They are made of solid cast iron with hollow iron handles. Flat irons were commonly heated on trivets in front of open fires, or on the tops of closed ranges. They were made in numbered series which related to their size, but there did not appear to be any standardisation in the series between manufacturers.domestic appliances, flat irons, sad irons

T. & C. Clark & Company Limited was based at Shakespeare Foundry in Wolverhampton England and was founded in 1795 by Thomas and Charles Clark. The company grew to be one of the largest iron foundries in Wolverhampton and were pioneering in the manufacture of enamelled cast iron cookware and sanitary wares. The company's product range included thousands of items, both domestic and industrial. T. & C. Clark were pioneers in the use of enamelled cast ironware, after taking out a patent in 1839 guaranteeing their products to be free of lead or arsenic. The company became the largest employer in Wolverhampton employing between 600 to 700 people.The item is significant as it was used as a domestic kitchen item to cook food safely without the concern that the metal may contain lead or arsenic as earlier cooking utensils had.Cast Iron cooking pot with lid separate Straight rod handle painted black.On base "T&C Clark and Co Ltd, RD455270 First Quality"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, flagstaff hill maritime village, great ocean road, cooking pot, iron cooking pot, cook ware, saucepan, kitchen utensil, cast iron enamel ware

Dutton and Wiggs operated a brass and iron foundry known as the Warrnambool Brass and iron Foundry situated in Timor St. Mr Dutton was a mechanical engineer and Mr C Wiggs was an experienced foundry worker. They were innovative in their work and also manufactured a large number of everyday items such as verandah posts, brackets and milk aerators.The significance lies in the fact that the items were manufactured in Warrnambool by a well- established local business. Two solid cast iron rods of cylindrical shape with one flattened edge with name imprinted. Hollowed out section on one end. S. Wiggs W,bool. One has the number 7 and the other 5 cast into the metal. warrnambool, wiggs, dutton & wiggs, window weights

The Tawonga Primary School celebrated its centenary on 25 - 26th Oct. 1980 with a program including a fete selling clothing with the option of buying iron-on transfers of the school building.Tawonga School was one of the earliest schools in the Upper Kiewa Valley supplying an education for the children of the farming community. Iron - on transfers were popular at the time.Brown fancy print and sketch of Tawonga School building done back to front on stiff iron-on paper."Tawonga School Centenary at top." '1880 - 1980' at bottom'tawonga primary school; iron-on transfer

This was a Slab Hut (Orbost Information Centre) display item. Cast iron was a suitable material for pots and pans because it heats up fairly quickly and retains the heat for some time. Soot from the fire would cover the cast iron and give the pot its black appearance. This was considered good because dark colours absorb heat more readily. The were used for cooking in a variety of situations, such as on an open fire and wood-burning stove. The long handle was essential for cooking on open fires to keep the flame of the fire at a distance, and to avoid burning one’s hand.This pan is an example of a common domestic item used in the late 19th century by early residents of Orbost.A shallow cast iron frying pan with a long tubular handle. In the top of the handle is a hole for hanging.On the handle is the number 3.domestic-utensils kitchen-ware cast-iron frying-pan

Ornamental drop finials x 4 from the lighthouse staircase.The four cast iron drop finials are decorative architectural features that were appended to the underside of the original lighthouse staircase, which was built between 1861 and 1862.The Conservation Management Plan prepared by Australian Construction Services in 1992 states that the original stair ‘was probably the first cast iron spiral stair to be built in an Australian lighthouse.’ From about 1978 to 1988 the tower’s original staircase was gradually removed and replaced by an iron replica and by 1992 the dismantled staircase had been shifted to the old jetty storage building and was ‘awaiting disposal’. Fortunately, it was not trashed but accessioned into the Eden Killer Whale Museum where it has since been incorporated into a recreated lighthouse.The staircase was removed from the tower prior to the lightstation’s inclusion in the Victorian Heritage Register in November 1999 (H1773). which may be the earliest cast iron spiral stair built in an Australian lighthouse.The four baluster drop finials are of first level contributory significance to the Gabo Island Lightstation for their historic value and clear provenance to the tower’s original staircase erected in 1862, which may be the earliest cast iron spiral stair built in an Australian lighthouse.4 x Cylindrical shaped finials. Threaded inside. Cast iron. tapers to a point. 1. & 2. have residue paint.

Iron sculpture by Cliff Burtt welcomes visitors to the Gateway of Eltham. It was constructed of Corten Steel in 1994 and won the Eltham Public Art Award in 1996. “Award winning sculptor, Cliff Burtt, often references the geometry of architectural forms in his bold, minimalist public sculptures. In this corten steel work the repeated arches of the temples of antiquity are in dialogue with the nearby spans of the railway trestle bridge that cuts through the Eltham parkland. The formality of the architecture is offset by the organic sweeps of the top profile of the work, which playfully acknowledges the hilly topography of the region” – Highlights from the Nillumbik Art Collection Two colour photographs of iron sculptureclassical landscape, sculptures, art, parks, alistair knox park, eltham, cliff burtt, public art

T. & C. Clark & Company Limited was based at Shakespeare Foundry in Wolverhampton England and was founded in 1795 by Thomas and Charles Clark. The company grew to be one of the largest iron foundries in Wolverhampton and were pioneering in the manufacture of enamelled cast iron cookware and sanitary wares. The company's product range included thousands of items, both domestic and industrial. T. & C. Clark were pioneers in the use of enamelled cast ironware, after taking out a patent in 1839 guaranteeing their products to be free of lead or arsenic. The company became the largest employer in Wolverhampton employing between 600 to 700 people.The item is significant as it was used as a domestic kitchen item to boil water safely without the concern that the metal may contain lead or arsenic as earlier cooking utensils had. Cast Iron Kettle straight metal handle painted black. Rusted inside and holed in the bottom, "T C Clark England" RD665876, 3 quarts No3" and other unreadable inscriptions.flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, flagstaff hill maritime village, great ocean road, kettle, iron kettle, kitchen ware, t c clark, enamel cook ware, cast iron kettle

T. & C. Clark & Company Limited was based at Shakespeare Foundry in Wolverhampton England and was founded in 1795 by Thomas and Charles Clark. The company grew to be one of the largest iron foundries in Wolverhampton and were pioneering in the manufacture of enamelled cast iron cookware and sanitary wares. The company's product range included thousands of items, both domestic and industrial. T. & C. Clark were pioneers in the use of enamelled cast ironware, after taking out a patent in 1839 guaranteeing their products to be free of lead or arsenic. The company became the largest employer in Wolverhampton employing between 600 to 700 people.The item is significant as it was used as a domestic kitchen or camp fire item used to cook food safely without the concern that the metal may contain lead or arsenic as earlier cooking utensils had. T C Clark innervates the first manufacturing process of cast iron cook ware to have enamel lining in his products to alleviate the possibility of lead or arsenic contamination of food.Cooking pot cast iron with lid and handle and lid pressed sheet steel oval shaped."T & C Clark and Co Ltd" (Star of David) "ENGLAND", "RD 455279" "3 GALLS" "FIRST QUALITY" Lid marked "CLARK" flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, flagstaff hill maritime village, great ocean road, kettle, cooking pot, cook ware, kitchen ware, cast iron kettle, t c clark ltd, shakespeare foundry

Used as holder for military medal/ Iron Cross. Awarded posthumously to Lance Corporal Gefreiter Franz Rapp who died in action on the Finnish front in 1941.Blue envelope with black printing (old german script) and slit at the back for closing *Iron Cross- 2nd class 1939G.F. Rapp . , 6franz rapp, iron cross, military medals german

Small black and white photograph of the entrance to Victoria Park showing high iron gates that are open. The gates are open but the gate on the right is behind the fence. There are caste iron lamps at either side of the gates in front of the bowed-top picket fence. Between the gates, in the distance the fountain is visible. Murray pines are also visible. Wide dirt approach.Victoria Park is of social and historical significance to the people of Echuca and district. It includes a state park that has a natural dry schreyphyll forest with a canopy of eucalypts. The Park also includes sporting grounds and facilities and picnic areas. This photograph depicts the entrance to the Park in the 1920s showing a dirt approach with the caste iron lights, iron gates and caste iron gate posts and the bowed-top picket fence. Black and white photograph of the entrance to Victoria Park showing high iron gates and lamps with bowed-top picket fence. Wide dirt approach.On the back of photograph, in pencil, "Park Entrance"victoria park, echuca

The iconic bush surrounds of Lake Daylesford are now home to a new permanent artwork titled Cottage, by artist Jason Waterhouse. The artwork has been months in the making, thousands of S-shaped pieces have been hand crafted from three kilometres of wrought iron, then joined together to form a scaled-down miners cottage. ‘Cottage’ is a highly decorative wrought iron sculpture inspired by the gates at the Convent in Daylesford, “ said Waterhouse. “This work references the rich opulence of the Victorian gold rush and pre-war spa resort era in its patterning. In its form ‘cottage’ pays homage to the miners, workers and farmers on whose backs the riches of Daylesford were built.” Cottage is the first in a series of significant public artworks to be commissioned by Hepburn Shire Council. Cottage will enhance one of Victoria’s premier tourist destinations, Lake Daylesford. Large scale wrought iron public sculpture referencing the worker's cottage of the Goldrush period in Daylesford. 203cm (height) x 382cm (width) x 353cm (depth) verandah 159.5cm (height) wrought iron 32mm x 2.5mmpublic art, sculpture, jason waterhouse, stockroom, daylesford, hepburn shire, daylesford lake, cottage, site-specific art, art, wrought iron, hepburn, hepburn shire public art collection

Although this house has been clad and had an iron roof put onto it, the historical integrity still appears to be intact. Colour photograph of a clad weatherboard house in Lydiard (North) Street Ballarat. Some of the iron roofing has been removed exposing shingles.weatherboard, shingles, lydiard street, house

This item was in use before electricity and was manufactured after the flat stove irons.The weight of the iron base, is heavy, helping in smoothing out crinkly material being ironed. This item permitted ironing of clothes to be separate and away from heating stoves. It permitted greater flexibility for ironing clothes and permitted more control (consistency) of the temperature of the iron.Historically and significantly this item enforces the relative isolation of the Kiewa Valley and period when and where this domestic item was in use(manufactured circa 1950). A rural setting with mining, beef , milk and tobacco production in the early 1900s. Even though the community was in a rural setting, the standards of dress was the same as in the bigger towns and cities. Social and religious mores and values demanded that the personal appearance be clean and crisp no matter where a person was living or working. Heavy laborious work was considered by some religions as virtuous, therefore the heavy and tiring work of ironing during this period had its rewards. Rural areas where the last to be connected to electricity and therefore this item was a domestic necessity far into the 1950's.This iron has a steel base and a metal body coated with green coloured enamel. The wooden hand grip is painted dark green. The kerosene (spirit) container is a chrome metal cylinder with a flat bottom and top. The top has a small filler/air plug is located on the top side. There are two control knobs located next to and under the metal cylinder. The close to the cylinder is a lock which locks the top lid of the iron and the other knob controls the airflow to the heater rodOn the base of the handle "PEERMAN" and below this P/46, C.I. Thomas & Son Pty Ltd household, ironing, domestic kerosene, dry cleaning

The 1950's saw a revolution in small appliances for use in the average household. This hand held wrench was provided exclusively for the Coleman self heating kerosene (KVHS 0347A) iron and used for the regular changing the kerosene used in it. The iron was used before and during the electricity supplies available from the Kiewa Hydro Electricity Scheme. These irons remained in use within regional rural areas that had limited or unreliable electrical reticulation. Kerosene supplies were cheaper than electricity but also more inconvenient than electric. Electrical appliances become cheaper to buy and maintain in the later part of the 1900's and the now older kerosene iron was faded out.This wrench was required to open the fuel container which stored kerosene in the Coleman hand iron(see KVHS 0347A). This item was part of the maintenance requirement of this particular hand iron. In the 1950s and later the Kiewa Valley was still a relatively isolated region which was home to rural properties and small settlements. The availability of electricity and or the financial means to afford new types of electric hand irons ensured that older and sometimes less efficient ironing remained for an extended period covering the 1960s to 1970s. Kerosene products, such as this kerosene iron was a cheaper method for farm based domestic and other rural activities requiring a heat source. The use of kerosene as a heat/light source was able to be supplied in bulk and able to be used when floods severed vital roads into this region. The supply of electricity was in summer time subject to interruption from bush fire damaged wooden poles carrying the electrical cables. Self sufficiency by rural populations was the backbone of survival(use of this wrench was a part of rural life). The ability to store energy sources "on the farm" was a prerequisite of isolated regions, such as the Kiewa Valley, circa 1950s.This item is a flat cast iron wrench, which has been specifically made for KVHS 0347A (kerosene iron). The wrench has four specific forms cut into the steel which fit firmly around their targeted nut and other fixtures. Also see See KVHS 0347B- Instruction sheet; and KVHS 0347D Fuel can.ironing, iron maintenance tool, domestic appliances, household

The Kiewa Hydro Electric Scheme (KHES) produced electricity for the people living in the Kiewa Valley and beyond to many parts of Victoria. The people and their families working on the scheme were encouraged by their employer the State Electricity Commission of Victoria to purchase and use electrical appliances. The iron was popular as it was quick and easy compared to those used previously. This iron belonged to Ron White who was a senior member of staff during the construction and operation of the KHES.This iron was owned by Ron White who was appointed Area Operations Engineer Kiewa in June 1956. He was later appointed General Superintendent and then, in 1974, he was appointed Principal Hydro Engineer of the recently titled Hydro Division.Rectangular yellow and black cardboard box with 'complete' fitting lid. Red and black writing on all sides except the bottom. staples used to hold down the sides of the lid.Front of box - New Revolutionary / Dry/ It steam irons/ it damps as it irons!/ It dry irons too! Back of box - Hoover Steam or Dry Iron Side of box - New Revolutionary / Hoover/ Steam or dry/ Iron / Made By/ Hoover Industries Pty Ltd Meadowbank NSW Top of box has sketch of dial "Big Safety Set Dial" - with black backgroundelectric iron; steam iron; hoover industries; ron white; laundry; kiewa hydro electric scheme

By the late 1800s increasing numbers of Australian working men had at least one good suit as a sign of respectability. Suits could be purchased ready-made, made to measure from a local tailor. The introduction of electric irons meant that the old flat irons and gas stove no longer had to be used. This electric iron would have been used to flatten seams during the tailoring process. This item is representative of a now rare craft that has diminished in the contemporary world.An electric tailor's iron. It has a green base and a black handle. The body of the iron has a flat back and curves to a point at its front. Its handle is metal and is attached with large screws at the top and back side of the base. The top of the handle is covered in black plastic that has finger grooves. there is a black iron resting stand.

Laterite refers to both a rock and a soil type that is rich in clay, as well as Iron and Aluminium. It is created during a process that is called laterization, where high heat and seasonal heavy rainfall cause there to be wet and dry periods, which over time hardens the soil into rock. Because of this, most laterite is formed between tropics of Cancer and Capricorn. The iron oxide in laterite is what gives it it’s orange-red colouring. The largest religious complex in the world, Angkor Wat in Cambodia, is partially constructed of laterite, particularly its foundations, as laterite is porous and allows rainwater to drain. This specimen of laterite was collected from the Democratic Republic of Congo while it was colonised by Belgium in the 19th century. Laterite forms in many parts of the world, particularly between the tropics. It is used both for ore and as a building material, and comparing specimens from different parts of the world allows us to document the different compositions that this mineral can have when formed at different locations. This specimen is part of a larger collection of geological and mineral specimens collected from around Australia (and some parts of the world) and donated to the Burke Museum between 1868-1880. A large percentage of these specimens were collected in Victoria as part of the Geological Survey of Victoria that begun in 1852 (in response to the Gold Rush) to study and map the geology of Victoria. Collecting geological specimens was an important part of mapping and understanding the scientific makeup of the earth. Many of these specimens were sent to research and collecting organisations across Australia, including the Burke Museum, to educate and encourage further study.a palm-sized solid iron-aluminium oxide mineral specimen in shades of brown, orange and greyburke museum, beechworth, geological, geological specimen, laterite, laterite specimen, geology

In the industrialized world, as stoves replaced open fires and braziers as a source of more efficient and reliable heating, models were developed that could also be used for cooking, and these came to be known as kitchen stoves.  The first manufactured cast-iron stove was produced at Lynn, Mass., in 1642. This stove had no grates and was little more than a cast-iron box. About 1740 Benjamin Franklin invented the “Pennsylvania fireplace,” which incorporated the basic principles of the heating stove. The Franklin stove burned wood on a grate and had sliding doors that could be used to control the draft (flow of air) through it. Because the stove was relatively small, it could be installed in a large fireplace or used free-standing in the middle of a room by connecting it to a flue. The Franklin stove warmed farmhouses, city dwellings, and frontier cabins throughout North America. Its design influenced the development of the pot-bellied stove, which was a familiar feature in some homes well into the 20th century. The first round cast-iron stoves with grates for cooking food on them were manufactured by Isaac Orr at Philadelphia, Pa., in 1800. The base-burning stove for burning anthracite coal was invented in 1833 by Jordan A. Mott. The subject item is a mid to late 19th century settlers stove probably of Canadian manufacture imported into Australia around this time. The stove gives us a social snapshot into what life must have been like for our early colonialists using this device for heating and cooking in their meagre homes. Cast iron stove with four-legs, 2 plates on top and a hinged front door. The door has been cast with a maple leaf design and the sides have a pattern cast into them.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, stove, domestic heating, domestic cooking, heater, cooking unit, pot belly stove, wood fired stove, wood stove

Historically, lasts were typically made from cast iron because this material retains its shape, even when in contact with wet materials (like leather) and subjected to the stresses of stretching and shaping shoes on them. This item is an example of the self-reliance shown by rural families when household necessities were not readily available.A cast iron boot last which can be used for three different sized sole placements boots / shoes.boot-last domestic shoes

The subject router is commonly referred to disparagingly as the ‘old woman’s tooth’ or ‘hag’s tooth.’ It is a router that houses a plough plane iron instead of a purpose made shoe-type cutting iron. They work fine but rarely give the type of clean surface required for veneer inlays. These types of tools are adjusted by the same hammer-tap tapping method used generally on wooden-bodied planes on the iron or plane body. These tools are effective and practical when used in general carpentry and joinery. Company History: The firm of Alexander Mathieson & Sons was one of the leading makers of hand tools in Scotland. Its success went hand in hand with the growth of the shipbuilding industries on the Firth of Clyde in the nineteenth century and the emergence of Glasgow regarded as the "second city of the Empire". It also reflected the firm's skill in responding to an unprecedented demand for quality tools by shipyards, cooperage's and other industries, both locally and far and wide. The year 1792 was deemed by the firm to be that of its foundation it was in all likelihood the year in which John Manners had set up his plane-making workshop on Saracen Lane off the Gallowgate in the heart of Glasgow, not far from the Saracen's Head Inn, where Dr Johnson and James Boswell had stayed on their tour of Scotland in 1773. Alexander Mathieson (1797–1851) is recorded in 1822 as a plane-maker at 25 Gallowgate, but in the following year at 14 Saracen's Lane, presumably having taken over the premises of John Manners. The 1841 national census described Alexander Mathieson as a master plane-maker at 38 Saracen Lane with his son Thomas Adam working as a journeyman plane-maker. In 1849 the firm of James & William Stewart at 65 Nicolson Street, Edinburgh was taken over and Thomas was put in charge of the business, trading under the name Thomas A. Mathieson & Co. as plane and edge-tool makers. Thomas's company acquired the Edinburgh edge-tool makers Charles & Hugh McPherson and took over their premises in Gilmore Street. The Edinburgh directory of 1856/7 the business is recorded as being Alexander Mathieson & Son, plane and edge-tool makers at 48 Nicolson Street and Paul's Work, Gilmore Street. The 1851 census records indicate that Alexander was working as a tool and plane-maker employing eight men. Later that year Alexander died and his son Thomas took over the business. Under the heading of an edge-tool maker in the 1852/3 (Post-Office Glasgow Annual Directory) the firm is now listed as Alexander Mathieson & Son. By the early 1850s, the business had moved to 24 Saracen Lane. The directory for 1857/8 records that the firm had moved again only a few years later to East Campbell Street, also off the Gallowgate, and that through further diversification was also manufacturing coopers' and tinmen's tools. The ten-yearly censuses log the firm's growth and in 1861 Thomas was a tool manufacturer employing 95 men and 30 boys; in 1871 he had 200 men working for him and in 1881 300 men. By 1899 the firm had been incorporated as Alexander Mathieson & Sons Ltd, even though only Alexander's son Thomas appears ever to have joined the firm. A vintage tool made by a well-known firm made for other firms and individuals that worked in wood. The tool was used for making timber veneers or smoothing a trench in a piece of timber that was then used in some form of cabinet manufacture or wood working enterprise. A significant item from the mid to late 19th century that today is sought after by collectors. It gives us a snapshot of how furniture was made predominately by hand and with tools that were themselves hand made and required considerable skill in their use. Old Woman's Tooth Router Mathieson. Single iron cut down from a larger plane iron. Has Marked A Mathieson & Son also stamped inscription on side G Hill. (owner)flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, plane, old woman's tooth, router, hag's tooth router, cabinet making, woodworking tools, a mathieson & sons, cabinet tool makers

See KVHS 1626 This cast iron camp oven was used inside or outside as it doesn't have any legs or lid. It is smaller than KVHS 1626.Used by people in the Kiewa Valley to cook food.Formerly UKV 023. Smaller cast iron camp oven than KVHS 1626 and without a lid or legs. See KVHS 1626cast iron camp oven

The Victorian Railways scales were donated by a resident of Wodonga, Victoria, and may have been used in the Wodonga train station. The Wodonga train line and train station opened in November 1873 when the section of the line from Wangaratta to Wodonga was completed. The expansion of Victorian Railways to the northeast of Victoria occurred after the Victorian Government took over the railways in 1867 and the trains serviced large towns such as Seymour, Wangaratta and Wodonga, as well as smaller towns along the way.The Victorian Railways weighing scales has local significance as it was donated by a resident of Wodonga, as well as state significance as an example of the equipment used by the Victorian Railways. Green painted cast iron Victorian Railways scales for weighing up to 25 kg. Rectangular weighing plate above a circular aluminium dial with the weights and 'V.R.' is engraved in black on the front of the scales."V.R." in black on the front of the scales "TO WEIGH / 25 kg. X 250 g." in black on the front of the scales "1714" engraved on a small iron plate screwed onto the front of the base of the scales.victorian railways weighing scales, v.r. weighing scales, railways scales, weighing scales, victorian railways, v.r., vr

The photograph was taken from the iron bridge on the Rupertswood Estate. The tower of the Rupertswood Mansion can be seen in the distance. The Eadie family were business people and millers in Sunbury.A post card featuring a dark sepia image of a creek with a large house in the distance. There is a hand written message on the back.Written on the back: Dear old boy Many happy returns of the 8th. I . . . . . . . . . . . . making the . . . .Yours ever Will. Iron bridge at Rupertswood. Mr Hal Eadie Dannevirke NZ.rupertswood mansion, jacksons creek

Large platform scales such as these ones made by W. & T. Avery were used for weighing goods for trading and passengers' luggage. They would be used in places such as railway stations, shipping ports, customs offices and ticketing offices. Often fees would be charged to customers according to the weight of their goods and luggage. Items would be placed onto the large horizontal platform then weights would be added to the weighing bar until the bar leveled to being horizontal. The weights would be added together and the total of the weights would be used for the final figure. These scales were made in Birmingham, England, by the British company, W and T Avery. The company had its origins in the early 1700s but only became known as W and T Avery when the brothers William and Thomas Avery inherited the scale-making business from a relative, Joseph Balden, on his death in 1813. By 1885 they had three factories and In 1895, the company acquired James Watt & Co and two years later had moved to the 25-acre Soho Foundry site in Smethwick, Birmingham where James Watt had manufactured steam engines. When the last Avery family member died in 1918, the company employed over 3,000 people and had businesses all over the world. Following the highly successful introduction of the first digital retail scale in 1971, the company was taken over by the GEC Group in 1979. The business was subsequently acquired by the American company, Weigh-Tronix, in 2000 which had already acquired a competitor, Salter. The Avery name continues today in the company known as Avery Weigh-Tronix.An item that was used at the turn of the century as train platform scales or for weighing agricultural products. Made by a company that pioneered weighing equipment with offices all over the world. With many examples of this scale in museums throughout the world. Platform scales with wheels. Large cast iron, scales painted black, weight capacity to 7 CWT (hundred weight). Weight beam has markers "0. 5. 10. 15. 20. 25". Platform scale loose weight type with relieving handle; cast iron construction, fluted columns with integral weight stand, the two wheels are fitted to base at front of platform; there is a graduated steelyard 0-14bs with pear-shaped poise. Weight carrier is missing.Pressed into cast iron arm on scale, one side "W. & T. AVERY", opposite side "BIRMINGHAM", and into the platform "TO WEIGH 7 CWT, W. & T. AVERY, MAKERS, LONDON & BIRMINGHAM" flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, measuring scales, weighing scales, weighing instrument, fees for goods, fees for luggage, ticket office