A hook as a hand tool is used for securing and moving loads. It consists of a round wooden handle with a strong metal hook projecting at a right angle from the centre of the handle. The appliance is held in a closed fist with the hook projecting between two fingers. This type of hook is used in many different industries, and has many different names. It may be called a box hook, cargo hook, loading hook, or a docker's hook, and a baling hook, bale hook, or hay hook in the agricultural industry. Other variants exist, such as in forestry, for moving logs, and a type with a long shaft, used by city workers to remove manhole covers. A hay hook is slightly different in design in that the shaft is typically longer. It is used on farms to secure and move bales of hay, which are otherwise awkward to pick up manually. A small bale hook with a wooden handle and 2 curved steel hooks pioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, graziers, wool bales, hay bales,

Before drills and braces, T-shaped augers were used to poke holes into wood, while smaller gimlets were used to start them.. A significant advance on the auger was the brace, which was originally designed with a single, permanently fixed bit at its end. Hand drills were often called eggbeater drills for their similarity to that common kitchen tool using a crank to drive the drill into the wood A steel hand drill with hand crank and wooden handlespioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, metalwork, woodwork, drills

Before drills and braces, T-shaped augers were used to poke holes into wood, while smaller gimlets were used to start them. Auger handles were usually made of a piece of hardwood that was sanded, rounded, or even contoured to give the user a firm grip. Bits on spoon augers essentially carved a hole in the piece of wood, and had to be periodically removed to clear the chips. Spiral-bit augers were precursors to modern drills, whose bits cleared the hole of chips as the user drilled. A significant advance on the auger was the brace, which was originally designed with a single, permanently fixed bit at its end. Eventually, though, braces were designed with sophisticated chucks to accommodate replacement bits, as well as bits of different sizes and for various purposes A steel spiral bit Auger* pioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, metalwork, woodwork, drills, augers, gimlets

A screwdriver is a tool, manual or powered, for turning (driving or removing) screws. A typical simple screwdriver has a handle and a shaft, and a tip that the user inserts into the screw head to turn it. The shaft is usually made of tough steel to resist bending or twisting. The tip may be hardened to resist wear, treated with a dark tip coating for improved visual contrast between tip and screw—or ridged or treated for additional 'grip'. Handle are typically wood, metal, or plastic and usually hexagonal, square, or oval in cross-section to improve grip and prevent the tool from rolling when set down. The handle and shaft of screwdrivers have changed considerably over time. The "Perfect Pattern Handle’ screwdriver was first manufactured by HD Smith & Company, which operated from 1850 to 1900. Screwdrivers were probably invented in the late 15th century, either in Germany or France when Screws were used to construct screw-cutting lathes, for securing breastplates, backplates, and helmets on medieval jousting armor—and eventually for multiple parts of the emerging firearms, particularly the matchlock. The jaws that hold the pyrites inside medieval guns were secured with screws, and the need to constantly replace the pyrites resulted in considerable refinement of the screwdriver. The screwdriver depended entirely on the screw, and it took several advances to make the screw easy enough to produce to become popular and widespread Canadian P.L. Robertson, though he was not the first person to patent the idea of socket-head screws, was the first to successfully commercialize them, starting in 1908. In Portland, Oregon, Henry F. Phillips patented his own invention, an improved version of a deep socket with a cruciform slot, today known as the Phillips Screw. Phillips offered his screw to the American Screw Company, and after a successful trial on the 1936 Cadillac, it quickly swept through the American auto industry. A main attraction for the screw was that conventional slotted screwdrivers could also be used on them, which was not possible with the Robertson Screw. A large steel screwdriver with worn wooden handlepioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, metalwork, woodwork, screws, philllips head screwdrivers, h.d.smith & co usa, p.l. robertson, henry f.phillips , oregon, canada, american screw company,

Before drills and braces, T-shaped augers were used to poke holes into wood, while smaller gimlets were used to start them. Auger handles were usually made of a piece of hardwood that was sanded, rounded, or even contoured to give the user a firm grip. Bits on spoon augers essentially carved a hole in the piece of wood, and had to be periodically removed to clear the chips. Spiral-bit augers were precursors to modern drills, whose bits cleared the hole of chips as the user drilled. A significant advance on the auger was the brace, which was originally designed with a single, permanently fixed bit at its end. Eventually, though, braces were designed with sophisticated chucks to accommodate replacement bits, as well as bits of different sizes and for various purposes. Chucks were patented as vigorously as the braces themselves The braces themselves also evolved for particular trades, from furniture makers to surgeons. The operator holds the ‘head’ in one hand, positions the drill in the wood , applies pressure and rotates the ‘centre piece’ to cause the drill to pierce the wood. A steel revolving hand tool for boring and screw-driving with wood handles * pioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, , blacksmiths, builders, farmers, metalwork, woodwork, screws

A hammer is a tool with a heavy head and a handle, often made of shock-absorbent wood or fiberglass that is used to strike an object. The most common uses for hammers are to drive nails, fit parts, forge metal, and break apart objects. Hammers vary in shape, size, and structure, depending on their uses. Hammers are basic tools in many trades. A hammer is composed of a head most often made of steel and a handle also called a helve or haft. Most hammers are hand tools. A traditional hand-held hammer consists of a separate head and a handle, fastened together by means of a special wedge made for the purpose, or by glue, or both. This two-piece design is often used, to combine a dense metallic striking head with a non-metallic mechanical-shock-absorbing handle -to reduce user fatigue from repeated strikes. If wood is used for the handle, it is often hickory or ash, which are tough and long-lasting materials that can dissipate shock waves from the hammer head. A well used hammer with wooden handle and steel headpioneers, early settlers, market gardeners, moorabbin, brighton, cheltenham, tools, craftsman, carpenters, blacksmiths, builders, woodwork,

This steel leather punch would be used by early settlers in Moorabbin Shire c1900when making and repairing, farm and household leather goods.Early settlers in Moorabbin Shire had to be self sufficient and made and repaired their farm and household equipment. Blacksmiths made the toolsA solid steel leather punchleatherwork, craftwork, moorabbin, bentleigh, cheltenham, early settlers

In the Middle Ages double-acting bellows was introduced. It had 2 parts, one operated by hand or foot, the other took air from it and was weighted so it forced air out while the part was filling. Blacksmithing is the shaping of hot iron and steel, usually by hammering. Very hot fires were produced by 1.a hot air blast. 2. burning charcoal (not wood). Bellows were used to make tools, fix equipment including machinery, drays, carriages, harnesses etc. Farmers in the Kiewa Valley often had their blacksmith forge. They made their own tools, were able to mend equipment, drays etc., gates, and most items that were made of iron and steel.Large Double Acting bellow with wooden top and bottom, shaped like a 'water drop' - narrow at one end and broad at the other. The wood is held by strips of wood and leather bound and placed around the perimeter. The wood on the top side has inscriptions (illegible). The wood on the bottom side has a rectangular hole. The narrow end feeds into a pipe to enable the fire to receive a hot blast of air. When the bellow is squeezed it allows both pieces of wood to be pushed together.Illegibleblackmiths, bellows, double acting bellow

These long handled "Blacksmith" tongs were used in the late 1800's to mid 1900's by a blacksmith(or others) within the Kiewa Valley. During these times blacksmiths would regularly visit "remote" rural properties and work on any "hard to manufacture" items. A few properties had either stockmen,farm hands, or owners able to do "minor" blacksmith work. The ability to undertake blacksmith functions was sometimes "by necessity" handled by a local "jack of all trades" person. During this period however demand for rural based blacksmiths was very high. The rural store, however was usually very small and many "off" the shelf rural appliances and apparatus available in the larger rural towns were not available to the semi remote rural areas.This long handled shaped nipper tongs is very significant to the Kiewa Valley because it represents one of the essential mores relating to isolated rural regions as was the Kiewa Valley at this period in time (1800's to mid 1900's). This "ingrained " more was the ability to achieve anything that was required to maintain a living standard or survival in a remote grazing, mining and farming region. The remoteness was due to the small population, poor transport routes and flood prone roads winding through the lower lying flat plains of the Kiewa Valley. Any blacksmith work whilst grazing Cattle on the Bogong High Plains or any part of the Kiewa Valley, had to be done in situ. The part of the "culture" of this regions was that of "self help" either from within the family or from a friendly neighbour.Long handled blacksmith's tongs. The handles are rusted and painted orange. The nippers have one central fixing and are flat edged.tools, blacksmith, horses, trades

These long handled "V" shaped tongs were used late 1800's to mid 1900's by a blacksmith within the Kiewa Valley. During these times blacksmiths would regularly visit "remote" rural properties and work on any "hard to manufacture" items. A few properties had either stockmen,farm hands, or owners able to do "minor" blacksmith work. The ability to undertake blacksmith functions was sometimes "by necessity" handled by a local "jack of all trades" person. During this period however demand for rural based blacksmiths was very high. The rural store, however was usually very small and many "off" the shelf rural appliances and apparatus available in the larger rural towns were not available to the semi remote rural areas.This long handled "V" shaped nipper tongs is very significant to the Kiewa Valley because it represents one of the essential mores relating to isolated rural regions as was the Kiewa Valley at this period in time. This "ingrained " more was the ability to achieve anything that was required to maintain a living standard or survival in a remote grazing, mining and farming region. The remoteness was due to the small population, poor transport routes and flood prone roads and lower flat plains of the Kiewa Valley. Any blacksmith work whilst grazing Cattle on the Bogong Plains had to be done in situ.Long handled tongs with "V" shaped ends on the nippers (used by blacksmiths)I.T.O.C.tools, blacksmith, horses, wrought iron tools

This blacksmith's hammer was an integral tool used by cattle property "blacksmith's" for the maintenance of horse shoes and the manufacture/alterations and repair of any other metal item required by the property. Self sufficiency was the key element to the success of a cattle property especially in semi isolated rural areas(early Kiewa Valley) and the larger the property ie. stock holding the greater the need..This blacksmith's hammer would not only have been used on the cattle property of the pioneer family (the Ropers) in the earlier part of the 1900s but also up in the Bogong High Plains grazing region to maintain the constant refurbishment/maintenance of horse shoes and other metal items. Depending on each property's requirement for blacksmith's service, one from the larger property could have serviced all the valley's requirements.Large blacksmith's hammer has a handle of twisted iron encircling 19 cm. hammer head. It has a round striking end and a wedge shaped punch end.V.B. [in dots ]tools, horses, punch, blacksmiths

Hand forged metal tool, possibly a sailmaker's hook with the hook broken. It may be a fire iron. The twisted metal is a skill learned by a blacksmith.The item is a handmade tool, an example of the work of a blacksmith. Smiths were sought after in colonial Australia. Their trade allowed them to custom make work for the different industries necessary for survival in a new land.Sailmaker's stretching tool; long thin metal rod bent in half, with centre forming a handle or loop, and long ends twisted together to form a stem. The loose ends are formed together but appear broken.warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, tool, sailmaker's tool, fire iron, blacksmith, twisted rod, twisted wire, sailmaker's hook

Fireplace tongs were used to add wood to the fireplace as well as break down the crackling wood to add more oxygen to growing flames. Of the four tools that were usually found in an upright fireplace set, tongs had the biggest design variation. Some tongs looked like medical calipers that were rounded at the bottom, while others were almost like metronomes with their rectangular shapes. https://www.lovetoknow.com/home/antiques-collectibles/vintage-antique-fireplace-tools Tongs are tools used to handle items, and generally move the item from one place to another, or turn things, like a piece of meat on a barbecue. Tongs usually have flat ends to pick up items without damaging them and to grip onto the items easily, however, some tongs have claws or toothed ends to grab more bulky and slippery items. Tongs are used mainly for handling food or hot items. Modern tongs are usually made from plastic, metal, stainless steel, or other material, depending on their purpose. Originally, tongs were probably wood sticks that eventually became metal sticks around 3000 BC to handle hot items in a fire Tongs are used to extend the hand or as a replacement handler for potentially dangerous items. Tongs usually have a sprung end so that the operator is required to squeeze the middle of the tongs to grab hold of an item, or they have a pivot which requires the user to squeeze the handles at the end to grip onto items, these being more effective at holding heavy items due to the extra force able to be applied. There are many types of tongs including barbecue tongs, salad tongs, blacksmith tongs, crucible tongs, ice cube tongs, sugar cube tongs and fire tongs. Tongs are often called ‘a pair of tongs’ and the word comes from the Old English, ‘tange’ or ‘tang’, meaning ‘that which bites’. There is evidence of Egyptians using metal rods and tong like tools to hold objects over fire, in around 1450 BC. https://tenrandomfacts.com/tongs/Fire tongs are still used with most open fires in homes.Brass fire tongs with holding clip and flat rounded handle at the end.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, fireplace tools, tongs

This book contains information relating to daily work conducted by Charles Edwards, Blacksmith, during period 20th January 1920 to 27 April 1921. It lists customer names, types of work done and costs involved. The written X indicates whether work was paid in full.This books contains historical information relating to peoples names and industries in the Bacchus Marsh district and the work performed for them by the blacksmith during the period mentioned. Most of work relates to shoeing horses, repairs to horse drawn vehicles, repairs to farm machinery/tools and some work on cars.Cardboard covers - green marbled design with black spine. Account type book with red ruled columns. Hand written names, jobs, charges and dates.On the inner cover - Mrs C Edwards, Main Street, Bacchus Marshbook, blacksmith, day, customers, clients, charles edwards

The Ballarat School of Mines offered a course in blacksmithing. These items were probably made at the Ballarat School of Mines.A number of hand forged steel tools.ballarat school of mines, blacksmith, forged, forge

Probably used in Ballarat School of Mines blacksmithing classesMetal stricker's Forging and Blacksmith tongs. Strong metal jaws to hold and move metal during processing. Hook at end on one handle to assist control. ballarat school of mines, blacksmith, forge

This set of taps and dies tools was owned by Frederick William McDowell (Fred) (1880 to 15-6-1967). He was a wheelwright by trade. He made and repaired vehicles such gigs, buggies, jinkers, sulkeys, spring carts and farm wagons. His workshop was on the corner of Cramer Street and Raglan Parade in Warrnambool., previously the site of Fotheringhams, and after McDowell's, and still in 2023, occupied by Reece Plumbing Fred's workplace prior to retiring was at Bryant & Waterson's in Kepler Street, opposite the Criterian Hotel, making rubber tyred horse-driven farm wagons. This Wiley and Russell hand operated, thread cutting Die and Stock, or Die and Tap, set’s patent carries the description “The taper-headed screws adjust the size; the four side screws hold the cutters firmly in the holder. Marketed as the Wiley & Russell LIGHTNING SCREW PLATE. The taper-headed screws are carried over from the J.J. Grant October 21, 1871 patent (no. 120,266). This patent was improved by Smart's Oct. 21, 1884 patent (no. 306,783).” Dies are used to cut external screw thread, stocks are the tools that hold the dies in place with countersunk adjustable screws, and taps are the tools that make the internal threads. The tools would be used by farriers, blacksmiths, wheelwrights sailing and steam ship engineers for making new, or repairing old, threads in metal. WILEY AND RUSSELL Manufacturing Company The company Wiley and Russell was established in 1872 by Solon Wiley and Charles P Russell, whose uncle founded the J. Russell Cutlery Co. The company began with the purpose of manufacturing thread cutting tools in Green River U.S. This tap and die set is an example of tools used by blacksmiths, farriers, wheelwrights and engineers on sailing and steam ships. It is also an example of early U.S. made engineering tools.Tap, Die, Die Stock set of industrial tools, fitted inside original timber box with three instruction labels attached inside lid. The set is the “Wiley and Russell LIGHTNING SCREW PLATE Pat. Aug. 5, 1884”. The lid has three metal hinges and is secured by two metal hook and eye fittings. This set of Whitworth standard threads has metal die and stocks (seven), and taps (three - the case has provision for four more die). The manufacturer’s details and the sizes of the threads are impressed into the tools. The paper labels have instructions and a diagram for the use and care of the tools. Tools have a protective oil coating. Made by Wiley and Russell Manufacturing Co. of Greenfield, Massachusetts, U.S., c. 1884; the tools were patented in August 1884, U.S. Patent 303,060. “Wiley & Russell MFG.CO, Greenfield, Mass, Pat Aug 5 1884.” “WHIT. STD.”flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, tap and die set, 1884 engineering tools, wiley and russell mfg co, lightning tap and die set, tap, die and stock set, screw thread cutting tools, taps and dies, stocks and dies, lightning screw plate, cutters, j.j. grant, patent no. 120266, solon wiley and charles p russell, wiley and russell, j. russell cutlery co, green river u.s, whitworth thread, fred mcdowell, frederick mcdowell, wheelwright, gig, buggy, jinker, sulkey, spring cart, farm wagon, 2-wheeled cart, horse cart, horse cart parts, jinker buggy, transport, vehicle, horse drawn, horse jinker, bryant & waterson

Owner of tools Jim Gillespie Clayton VictoriaCaulking iron blacksmith made boot iron, this iron is used for setting down deck seams where they are crossed by a steam or water pipe over the deck. They were also useful in other awkward places e.g. around winches. Driving force either mallet or hammer.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

A hay rake is an agricultural rake used to collect cut hay or straw into windrows for later collection (e.g. by a baler or a loader wagon). It is also designed to fluff up the hay and turn it over so that it may dry. The next day it is spread again, so that the hay dries more quickly. Early settlers established productive market gardens, poultry,. pig and dairy farms , orchards and vineyards on the land in the 'Henry Dendy Special Survey Brighton 1841' - now Ormond, Bentleigh, East Bentleigh, Brighton, This hay rake is typical of the type used by early settlers in Moorabbin Shire c1900Large wooden Hay rake , hand made c1900farm equipment, hay rakes, hammers, early settlers, market gardeners, blacksmiths, tools, building equipment, moorabbin shire, bentleigh, mckinnon, highett, cheltenham,ormond

A separator is a centrifugal device that separates milk into cream and skimmed milk. Separation was commonly performed on farms in the past where farmers milked a few cows, usually by hand, and separated by letting milk sit in a container until the cream floated to the top when it could be skimmed off by hand. Some of the skimmed milk was consumed while the rest was used to feed calves and pigs. Enough cream was saved to make butter, and the excess was sold. Manual rotation of the separator handle turns a mechanism which causes the separator bowl to spin at thousands of revolutions per minute. When spun, the heavier milk is pulled outward against the walls of the separator and the cream, which is lighter, collects in the middle. The cream and milk then flow out of separate spouts. Montgomery Ward was founded by Aaron Montgomery Ward in 1872.as a mail-order business in Chicago, Illinois USA. Rural customers were attracted by the wide selection of items that were unavailable to them locally and were also inspired by the innovative company policy of "satisfaction guaranteed or your money back".This milk separator is typical of the type used by early settlers in Moorabbin Shire where every family owned a 'house cow' to supply their dairy needs. Households also kept a few chickens for eggs and developed a vegetable garden with additional fruit trees. A 'primrose' manual milk separator 'Montgomery Ward', Chicago USA c1900'primrose ' / SATTLEY / MONTGOMERY WARD/ CHICAGOearly settlers, dairy farmers, milk products, dairies, market gardeners, blacksmiths, tools, moorabbin shire, bentleigh, mckinnon, highett, cheltenham, moorabbin