Showing 348 items
matching cut work
-
Flagstaff Hill Maritime Museum and Village
Tool - Joiner or Jack Plane, Late 19th to first quarter of the 20th century
... ) to prevent digging in to or marking the work. The cut is generally... in to or marking the work. The cut is generally set deeper than on most ...A jack plane (or fore plane) is a general-purpose woodworking bench plane, used for dressing timber down to the correct size in preparation for truing and/or edge jointing. It is usually the first plane used on rough stock, but in exceptional cases can be preceded by the scrub plane. Jack planes are 300–460 mm long and 64–76 mm wide, with wooden-stocked planes sometimes being slightly wider. The blade is 44–57 mm wide that is often slightly convex (or ground with rounded corners) to prevent digging in to or marking the work. The cut is generally set deeper than on most other planes as the plane's purpose is to remove stock rather than to gain a good finish (smoothing planes are used for that). In preparing stock, the jack plane is used after the scrub plane and before the jointer plane and smoothing plane. The carpenters' name for the plane is related to the saying "jack of all trades" as jack planes can be made to perform some of the work of both smoothing and jointer planes, especially on smaller pieces of work. Its other name of the fore plane is more generally used by joiners and may come from the fact that it "is used before you come to work either with the Smooth Plane or with the Jointer". Early planes were all wood, except for the cutter, or combined a wood base with a metal blade holder and adjustment system on top. Although there were earlier all-metal planes, Leonard Bailey patented many all-metal planes and improvements in the late 19th century. A jack plane came to be referred to as a "No. 5" plane or a "Bailey pattern No. 5" at the end of the 19th century. A vintage tool made by an unknown company, this item was made commercially for firms and individuals that worked in wood and needed a tool that could remove large amounts of timber. These jack or dressing planes came in various shapes and sizes to achieve a flat and even finish to timber surfaces before the use of smoothing planes and came in many sizes. A significant tool from the mid to late 19th century that is still in use today with early models sought after by collectors. It gives us a snapshot of how furniture and other finishes were created on timber by the use of cutting edged hand tools. Tools that were themselves handmade shows the craftsmanship used during this time not only to make a tool such as the subject item but also the craftsmanship needed to produce a decorative or even finish that was needed for the finishing of timber items. Jack or Fore plane with blade and wedge. Marked "D Morris" (owner)flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, plane, fore plane, d morris, jack plane, wood working tools -
Flagstaff Hill Maritime Museum and Village
Tool - Plane, Mid to late 19th Century
... ) to prevent digging in to or marking the work. The cut is generally... in to or marking the work. The cut is generally set deeper than on most ...A jack plane (or fore plane) is a general-purpose woodworking bench plane, used for dressing timber down to the correct size in preparation for truing and/or edge jointing. It is usually the first plane used on rough stock, but in exceptional cases can be preceded by the scrub plane. Jack planes are 300–460 mm long and 64–76 mm wide, with wooden-stocked planes sometimes being slightly wider. The blade is 44–57 mm wide that is often slightly convex (or ground with rounded corners) to prevent digging in to or marking the work. The cut is generally set deeper than on most other planes as the plane's purpose is to remove stock rather than to gain a good finish (smoothing planes are used for that). In preparing stock, the jack plane is used after the scrub plane and before the joiner plane and smoothing plane. The carpenters' name for the plane is related to the saying "jack of all trades" as jack planes can be made to perform some of the work of both smoothing and joiner planes, especially on smaller pieces of work. Its other name of the fore plane is more generally used by joiners and may come from the fact that it "is used before you come to work either with the Smooth Plane or with the Joiner". Early planes were all wood, except for the cutter, or combined a wood base with a metal blade holder and adjustment system on top. Although there were earlier all-metal planes, Leonard Bailey patented many all-metal planes and improvements in the late 19th century. A jack plane came to be referred to as a "No. 5" plane or a "Bailey pattern No. 5" at the end of the 19th century. A vintage tool made by an unknown company, this item was made commercially for firms and individuals that worked in wood and needed a tool that could remove large amounts of timber. These jack or dressing planes came in various shapes and sizes to achieve a flat and even finish to timber surfaces before the use of smoothing planes and came in many sizes. A significant tool from the mid to late 19th century that is still in use today with early models sought after by collectors. It gives us a snapshot of how furniture and other finishes were created on timber by the use of cutting edged hand tools. Tools that were themselves hand made shows the craftsmanship used during this time not only to make a tool such as the subject item but also the craftsmanship needed to produce a decorative or even finish that was needed for the finishing of timber items. Jack Plane handle is attached by large screw there is a round piece of wood tacked to front. noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, jack plane -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Barbers' Equipment, hair clippers 'BURMAN", c1950
Hair clippers are specialized implements used to cut human head hair. They work on the same principle as scissors, but are distinct from scissors and razors. :Hair clippers comprise a pair of sharpened comb-like blades in close contact one above the other which slide sideways relative to each other, a mechanism which may be manual or electrical to make the blades oscillate from side to side, and a handle. The clipper is moved so that hair is positioned between the teeth of the comb, and cut with a scissor action when one blade slides sideways relative to the other. Friction between the blades needs to be as low as possible, which is attained by choice of material and finish, and frequent lubrication. Hair clippers are operated by a pair of handles that are alternately squeezed together and released. Barbers used them to cut hair close and fast. The hair was picked up in locks and the head was rapidly depilated. Mid 20thC such haircuts became popular among boys, and young men in the military and in prisons. Burman & Sons Ltd, of Ryland Road, Birmingham, West Midlands, manufactured Burman-Douglas steering gear. Their recirculating worm and ball design of steering gear was fitted to pre-war vehicles such as the Ford Eight and the Ford Prefect, the Bedford CA, plus heavy trucks and off-road vehicles - both pre and post-war. In its day, Burman-Douglas steering-gear was regarded as.... a "quality" feature of a car chassis specification, but the worm and ball design was eventually surpassed by the cheaper rack and pinion design that dominates today. The company also manufactured motorcycle gearboxes, horse clippers and barbers’ clippers. 1871 Company founded. 1897 Private company. 1930s Gearbox for Ariel Square-four motorcycle. (Exhibit at Birmingham Thinktank museum) 1933 Burman and Sons Limited, manufacturers of horse and barbers' clippers, sheep shearers, motor cycle gear boxes and steering gears, Ryland road, Edgebaston 1953 S. F. Burman, M.B.E., Managing Director, Burman and Sons, Ltd 1955 Acquired by Vono Industrial Products. 1961 Manufacturers of motor and motorcycle accessories. 1,500 employees. 1968 Supplied rack and pinion steering units to Ford 1978 Adwest Group acquired Burman and Sons, the steering gear part of Duport. 1986 Major reduction in staffing at Burman due to fall in demand for its products and delivery problems. A set of hand held barbers’ hair clippers with an adjustable screw, from Burman and Sons Ltd of Birmingham, England. Chrome plated, in good condition, c1950. On left arm ; BURMAN On right arm ; MADE IN ENGLANDbarbers, hairdressing, hair clippers, grooming, horse clippers, cars, motor cycles, gear boxes, rack and pinion , worm and ball, steering gears, steel manufacture, birmingham england, burman and sons ltd, moorabbin, bentleigh, ormond, cheltenham, market gardeners, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Barbers’ Equipment, hair clippers steel, c1950
Hair clippers are specialized implements used to cut human head hair. They work on the same principle as scissors, but are distinct from scissors and razors. :Hair clippers comprise a pair of sharpened comb-like blades in close contact one above the other which slide sideways relative to each other, a mechanism which may be manual or electrical to make the blades oscillate from side to side, and a handle. The clipper is moved so that hair is positioned between the teeth of the comb, and cut with a scissor action when one blade slides sideways relative to the other. Friction between the blades needs to be as low as possible, which is attained by choice of material and finish, and frequent lubrication. Hair clippers are operated by a pair of handles that are alternately squeezed together and released. Barbers used them to cut hair close and fast. The hair was picked up in locks and the head was rapidly depilated. Mid 20thC such haircuts became popular among boys, and young men in the military and in prisons. A set of hand held barbers’ hair clippers with an adjustable screw. Chrome plated, in good condition, c1950 barbers, hairdressing, hair clippers, grooming, horse clippers, steel manufacture, moorabbin, bentleigh, ormond, cheltenham, market gardeners, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, steel hacksaw 'Marples', 20thC
A hacksaw is a fine-toothed saw, originally and principally for cutting metal. They can also cut various other materials, such as plastic and wood; for example, plumbers and electricians often cut plastic pipe and plastic conduit with them. On hacksaws, as with most frame saws, the blade can be mounted with the teeth facing toward or away from the handle, resulting in cutting action on either the push or pull stroke. In normal use, cutting vertically downwards with work held in a bench vice, hacksaw blades should be set to be facing forwards. Joseph Marples & Son Pty Ltd Traditional Craftsmans Hand Tools made in Sheffield. The finest quality hand made tools, backed by over 170 years of manufacturing heritage. .In the 1840’s Joseph Marples was one of several ‘Marples’ (most of which were related) in Sheffield manufacturing joiners tools, such as brass inlaid rosewood & ebony braces, boxwood spokeshaves, beech planes, gauges and squares. The business has remained within the family to this date, and has been based in Sheffield since those early days. Although modern technology has been used in some instances, many of the traditions of manufacturing fine hand tools has remained the same using selected materials and hand finishing, indeed the same threads are used in the gauges as were used over 100 years ago. A steel hacksaw. 'Marples' with bladeMARPLEStools, woodwork, metalwork, carpentry, pioneers, market gardeners, early settlers, moorabbin, cheltenham, bentleigh, ormond, joseph marples & son pty ltd, sheffield , england, -
City of Moorabbin Historical Society (Operating the Box Cottage Museum)
Tools, steel hacksaw with wooden handle, c1900
A hacksaw is a fine-toothed saw, originally and principally for cutting metal. They can also cut various other materials, such as plastic and wood; for example, plumbers and electricians often cut plastic pipe and plastic conduit with them. On hacksaws, as with most frame saws, the blade can be mounted with the teeth facing toward or away from the handle, resulting in cutting action on either the push or pull stroke. In normal use, cutting vertically downwards with work held in a bench vice, hacksaw blades should be set to be facing forwards. A steel hacksaw with a wooden handle but without blade -
The Beechworth Burke Museum
Photograph - Photograph - Reproduction
After gold was discovered to be deposited "for miles along Woolshed Valley" in the early 1850s, the Woolshed became a major site of mining activity in the north-east . This region was divided into large claims of 80 yards long, one of which was the one depicted in this photograph, called 'Big Johnson's Claim'. Claims such as this utilised a range of technology, including water wheels, steam engines, sluices and toms, most of which would not arrive until after 1856 when this photograph was taken. The Woolshed initially became prosperous in 1855, and labourers, such as the ones depicted in this photograph, engaged in sinking work for 7 pounds a week, whilst other mining labourers could earn up to nine. The search for gold is ingrained into the history of Victoria and therefore, images like this one which portray an open cut sluicing site can reveal important information for society and technology for the date when the photograph was taken. This image is of important historical significance for its ability to convey information about the operations of mining claims, particularly of the Woolshed Valley area that this photograph documents. This image is important for current research into the history of Woolshed, which was a major site of mining significance and operations. Therefore, this image has the capacity to be beneficial for research into society and the motivations of those living and working in this region during this period and therefore, has social significance. The Beechworth Burke Museum has additional images relating to gold sluicing and the Woolshed area which can be analysed and studied alongside images like this one. A black and white rectangular photograph printed on matte photographic paper.Reverse: 7791 / page 34. / 52% / Big Johnstone / Claim on Woolshed Goldfields / 1856 / Note canvas [illegible] building / Burke Museum /woolshed, mining, claims, mining claims, big johnson, gold -
Geelong RSL Sub Branch
Nurses Cape V10909 Margaret A Brown, There are no makers marks, All items circa 1940
The Cape belonged to V10909 Margaret Annie Brown who served with the AMF during WW2. Margaret A Brown enlisted on 17 September 1940 and was discharged with the rank of Major on 28 July 1944. Margaret Brown worked at the Heidelberg Hospital and also as Matron at Puckapunyal. Margaret Brown missed out on a posting to Hospital Ships working in the Pacific because of her age at the time - 40 - the cut off for the assignment was 40. One of Margarets co-workers at Heidelberg Vivian Bullwinkle - late 20ish at the time - gained a posting oversees.This is the original Nurses Cape that belonged to V10909 Margaret A Brown. The Soldiers Paybook and Appointment Certificate are originals belonging to V10909 Margaret A Brown.A Scarlett Nurses Cape. There are two Major Badges of Rank on the epaulettes and two Australian Military Forces buttons holding the epaulettes to the shoulders. Soldiers Pay Book, Continuation. Cardboard Cover, buff colour with paper pages. Appointment Certificate. Paper.The are no inscriptions or markings on the Cape. Pay Book No C81010, Army No. V10909, Name Brown, Christian Names Margaret Anne.nurses cape, v10909 m a brown, ww2, heidelberg, puckpunyal, pay book, appointment certificate -
Federation University Historical Collection
Colour photograph, Ballarat Courier Photographer, Former Ballarat Gaol Gates, 09-06-1997
The main gate to the former Gaol is a monumental work. The arch keystone facing Lydiard Street is beautifully executed. The gates and the iron lacework over the top are distinctive.The arch under the flyover is also distinctive; the basalt keystone appears to have been cut from one single block of stone. Most of the gaol has been demolished to allow the School of Mines Ballarat to expand onto the site. The remaining structures at the site include the main gate, warden's residence and governor's residence. These buildings are now used by Federation University.The main gate to the former Gaol is a monumental work. The arch keystone facing Lydiard Street is beautifully executed. The gates and the iron lacework over the top are distinctive.The arch under the flyover is also distinctive; the basalt keystone appears to have been cut from one single block of stone. gate, gaol, arch keystone, lydiard street, iron lacework, flyover, stone, basalt, ballarat school of minesfederation university, warden's residence, governor's residence -
Federation University Historical Collection
Document, Contract for the Madame Bent Gold Mining Company, 1886
Handwritten on foolscap paper, with red seal on last page.1) The Subcontractor is also to remove the following [ ? ] from Mr Webb's paddock ... to the Madame Bent Mine Grenville ... .2) Specification for the taking doan, removal and reerection 2 Engines 2 boilers pumping gear, Bob, Poppett heads and Capstone etc, for teh Mdame Bent G.M.Cy Grenville. The company will provide ... .3) Morey's Coys yard, together with holding down bolts, and the following ... .4) to the extent of Bed ... Carpentry Work - To carefully take down the poppet heads and co... and erect the same on the claim complete ... .5) Engine Framing as shown for the winding engines and pumping engines. Properly fitted to get ... .6) The boilers to be fed in front. The contractor to cut and drill all necessary holes in the boilers and pipes - to fire blow ... The contractor to make good any damage or breakage or loss to machinery or any part hereof that may occur to it during the removal of the reerection of same. The loss or damage, if any, not being made good by the contractor, or in the event of the works not being proceeded with to the satisfaction of the Company;s Engineer, The company's Engineer hereby ... .7) of the whole of the works, and in default thereof the COntractor shall forfeit the sum of two pounds ... Signed James Malcolm Witness L. Menz The Common seal of the company was affixed this thirteenth day of December:/86 by its manager James Burrell in the presence of [illegible] managers Seal - Madame Bent Gold Mining Company Durham Lead Buninyongmadame bent gold mining company, richard squire, james malcolm, james burrell -
Federation University Historical Collection
Book - Artwork, Ivy Wilson, Album of original Ballarat Technical Art School folio by Ivy Wilson, c1922
Ivy WILSON (1907-1998) Ballarat | Australia Ivy Wilson was born on 05 July 1907 to Charlotte and Edward Wilson of 167 Mair Street, Ballarat. She attended Humffray Street Primary School and the Ballarat Technical Art School (a division of the Ballarat School of Mines) in 1922. Wilson's student folio contains several stencils hand-cut from paper and card. Among them are stylised graphics of correa, waratah, gum, and kangaroo apple as well as kookaburras, cockatoos and a koala. With diverse applications, stencilling attracted a range of students at the Ballarat Technical Art School. Stencilling was applied to interior surfaces like cushions and curtains. Commercial briefs included wall friezes and murals. One of Wilson's examples, a wreath was subsequently translated into embroidered needlework. Wilson’s folio possibly consists of mostly junior technical work, as she appears to only have sat a single senior Education Department examination, Drawing Plant Forms from Nature. Alternatively, given her focus on textile-based arts, she may have been an evening trade student. Ivy Wilson married Frederick Henry Russell on 23 December 1933 at St Mary's Church of England Caulfield, and had one daughter - Nola, who gifted this folio to the University’s permanent Historical Collection. Ivy died on 17 November 1998 at Caulfield.Silver cloth covered photo album of artworks by Ivy Wilson. Gift of Nola Jones, daughter of Ivy Wilson, 2016 Contains original stencils, plus four photographs of a works kept by Ivy Wilson's family (2016).(Handwritten note) This art is the work of Ivy Wilson. born" 5th July 1907 to Charlotte & Edward Wilson of 17 Mair St. Ballarat. Attended Humffray St. Primary School and Ballarat School of Mines 1922. Married: Frederick Henry Russell December 23rd 1933 at St Marys CofE Caulfield Died 17th November 1998 at Caulfield. Mother of one daughter, Nola. ivy wilson, ballarat tecnical art school, artwork, dana street primary school, alumni, stencilling, stencils, embroidery, textiles, design -
Federation University Historical Collection
Clothing - Textiles, Ruth McGannon, Needlework, c 1950-70s
These items were made as samplers either at school or most likely college. They are samples of embroidery stitches, seam types and sewing and knitting techniques.Nos 1-16 are group of samplers made from cotton lawn, cotton with sateen weave and flannel and made by Ruth McGannon. No 17 is a pair of gloves made by Margaret Russell. .1) A small square of yellow lawn with three horizontal rows in blue thread and three vertical rows in red thread of running stitch each 3.5 centimeters apart. The edges are frayed to 1.2 centimeters. .2) A larger rectangle of yellow lawn with three horizontal rows 7.8 centimeters apart and three vertical rows 10 centimeters apart of long stitch, stitched in blue thread. The edges are frayed to 2 centimeters. .3) A small square of yellow lawn with three horizontal rows and three vertical rows of blue thread of running stitch, each 1.9 centimeters apart. The edges are frayed to 1.5 centimeters. .4) A larger rectangle of yellow lawn with three horizontal rows 9 centimeters apart and three vertical rows 11.2 centimeters apart of running stitch, stitched in red thread. The edges are hemmed with two rows of long stitch .5 centimeter apart with a loose blue thread of laced running stitch weaving in and out of the red long stitch. .5) A rectangle of hemmed yellow lawn with a pocket formed at each end. Two rows of long stitch in red thread hem the edges with a blue thread stitched between each red stitch. The pockets are formed by turning back the edges and stitching them down in brown thread. R.M. is embroidered in brown chain stitch on the right side. .6) A rectangle of hemmed blue lawn the same as the previous piece but with five rows of back stitch in yellow and orange thread creating a pattern. .7) A rectangle of blue lawn with the top and bottom edges hemmed with two rows of long stitch close together in yellow and orange. The other two edge are frayed to 2.5 centimeters and has four rows of long stitch .7 centimeter apart in yellow and orange thread. .8) A blue lawn bag with two packets was made by hemming a rectangle of fabric on three sides in long stitch with orange thread, then yellow thread between the stitches. The fourth side is hemmed in hemming stitch in yellow thread with blanket stitch in yellow thread along the edge. This edge is folded up by one third to create a pocket. The edges on either side are stitched together. A row of chain stitch in orange thread is stitched down the middle to create two pockets. A tape is stitched to either side at the top and this is folded over the pocket. .9) A cream cotton with sateen weave rectangle is hemmed with a double row of orange thread in long stitch. On both sides is embroidery in orange and yellow thread. .10) A yellow cotton with sateen weave baby's bib is made from a rectangle of fabric with a semi circle cut out of the top. The edges are turned and hemmed with a narrower turning on the neck. A tape is stitched at either side of the neck. On the front is embroidered a train in blue and yellow threads. .11) A yellow lawn embroidery sampler using blue and brown thread shows long stitch, stem stitch, herringbone stitch, chain stitch, fly stitch, lazy daisy stitch, cross stitch and satin stitch. It is hemmed using drawn thread work and the bottom is scalloped and finished in blanket stitch. .12) A pink lawn embroidery sampler with green thread shows herringbone stitch, stem stitch, running stitch, chain stitch, cross stitch, lazy daisy stitch, fly stitch, feather stitch, satin stitch and back stitch. The bottom is scalloped and finished in buttonhole stitched. The other three edges are hemmed using drawn thread work. .13) A small cream flannel square with two smaller squares are stitched together down the middle in decreasing sizes using chain stitch. The largest piece is hemmed using both herringbone and a decorative blanket stitch. It also has a run and fell seam on the opposite side using both running and herringbone stitches. A row of feather stitch is on either side of the seam. The two smaller squares are frayed on the edges. .14) A cream rectangular flannel sampler has two seams along the length. One is a run and fell seam using running and herringbone stitches and the other is an open seam using running stitch and both edges are stitched down with herringbone stitch. The two shorter edges are bound and the longer edges have a tape which is stitched down to neaten the edges. On the right side are two rows of feather stitch. .15) This blue lawn apron has a rectangular gathered skirt which is attached to a waistband and in turn attached to a bib front which goes over the head. The bib and skirt sides are hemmed using decorative blanket stitch in pink and dark blue thread. The skirt hem and both sides of the waistband are stitched in two rows of herringbone in pink and dark blue thread. .16) This pale pink lawn child's shirt has french seam side seams, a waist band to which the shirt is attached using slight gathering. The sleeves have cuffs. There is a front facing and a collar and there is a small pocket in the left hand breast. .17) These yellow knitted gloves are made using plain stitch for the hand and rib for the wrist.Written on paper and stitched on to a couple of items - Ruth McGannon V.3 - 312 Written on paper and stitched to the gloves - Margaret Russell x No2embroidery, sampler, gloves, stitches, sewing, knitting, apron, costume, needlework, dressmaking, textiles -
Federation University Historical Collection
Photograph - Colour photograph, Former Ballarat Gaol Gates, 24/04/2017
The main gate to the former Gaol is a monumental work. The arch keystone facing Lydiard Street is beautifully executed. The gates and the iron lacework over the top are distinctive.The arch under the flyover is also distinctive; the basalt keystone appears to have been cut from one single block of stone. Most of the gaol has been demolished to allow the School of Mines Ballarat to expand onto the site. The remaining structures at the site include the main gate, warden's residence and governor's residence. These buildings are now used by Federation University.The main gate to the former Gaol is a monumental work. The arch keystone facing Lydiard Street is beautifully executed. The gates and the iron lacework over the top are distinctive.The arch under the flyover is also distinctive; the basalt keystone appears to have been cut from one single block of stone. gate, gaol, arch keystone, lydiard street, iron lacework, flyover, stone, basalt, warden's residence, governor's residence, ballarat school of mines, federation university, former ballarat gaol -
Federation University Historical Collection
Painting - Ballarat Technical Art School Folio, Ivy Wilson, Artwork by Ivy Wilson, c1920-1922, 1920 - 22 (originals)
Ivy WILSON (1907-1998) Ballarat | Australia Ivy Wilson lived at 17 Mair Street with her parents while she studied at the Ballarat Technical Art School. Her student folio contains several stencils hand-cut from paper and card. Among them are stylised graphics of correa, waratah, gum, and kangaroo apple as well as kookaburras, cockatoos and a koala. One example of a wreath was subsequently translated into embroidered needlework. Wilson’s folio possibly consists of mostly junior technical work, as she appears to only have sat a single senior Education Department examination, Drawing Plant Forms from Nature. Alternatively, given her focus on textile-based arts, she may have been an evening trade student. A number of digitised images taken from a folder of works by Ivy Wilson undertaken at the Ballarat School of Mines Technical Art School between 1920 and 1922. The folio of work was later donated 'In memory of my mother Ivy Wilson'.ballarat school of mines, wilson, ballarat technical art school, dressmaking, art, ivy wilson, stencilling, stencil, embroidery, australian flora, australian birds -
Australian Jazz Museum
Jewellery
Size of box is 6cm x 4cm In 1936, young Eric Child (1910-1995) met, and squired around London's jazz night-spots, Lucille Wilson a dancer in Lew Leslie's Blackbirds stage production at the Gaiety Theatre. Although Lucille knew a few famous bandleaders she, at that time, had never heard of Louis Armstrong, THE King of jazz, according to Eric. Later, in a letter to Eric in late 1942, Lucille wrote that she had met his King - and had become his fourth wife on 7th October 1942. She had finally worked with Louis at the new Cotton Club in Harlem in 1939 where she was in the chorus line using the stage name Brown Sugar. The long platonic friendship with Lucille remained and Eric and his wife Angela (1919-2001) welcomed her and the King in Brisbane on Louis' first visit to Australia in April 1956, and on all subsequent visits here. At a dinner at the Child's Sydney home Lucille presented Angela with one of Louis' famous stage handkerchiefs, signed by the All Stars, and a her own brooch and earrings, which Angela had quite innocently admired. Following Eric's death in 1995, Angela promised the Louis handkerchief to Bill Haesler and the brooch and earrings to Jess Haesler when she died. Rather than keeping these unique items private, the Haeslers donated them, in Angela's memory to the Victorian Jazz Archive. A unique momento of jazz great Louis his wife Lucille Armstrong,and his Australian friends Eric and Angela Child.Costume jewellery - Silver and cut glass brooch and ear ringslucille armstrong, angela child, ear rings, brooch -
Federation University Historical Collection
Article - Catalogue package, Creativity Released, Advanced Diploma of Graphic Design, 2010
... . Unprinted, forme-cut black folder, triangular window, sealed ...Unprinted, forme-cut black folder, triangular window, sealed with triangular sticker containing a suite of A5 (148 x 210mm) cards promoting works of University of Ballarat, Advanced Diploma of Graphic Design (2 years) students. Contains 15, two-sided A5 cards, most featuring student work. Reverse of first card lists 12 graduates for 2010. Introduction by Paul Mah (co-ordinator / teacher). Teaching staff listed as Sam Harmer, Jill Hyatt, Slena Shillito, Travis Price, Ben Sanders, Anthony Woodward, Paul Mah, Alister Heighway, Peter Lambert, James Baker. Printed by Sovereign Press. Pack by Bennet-Meyer Packaging. One card features supporting sponsors Unprinted, forme-cut black folder, triangular window, sealed with triangular sticker containing a 15 A5 cards promoting student work.As per parent record, but opened. Promotional catalogue (pack of A5 cards) for graduating students of the University of Ballarat (TAFE), Advanced Diploma of Graphic Design. Unprinted, forme-cut black folder, triangular window, sealed with triangular sticker containing a 15 A5 cards promoting student work.university of ballarat, federation university, graphic design, tafe, advanced diploma, arts academy, camp street campus -
Ringwood and District Historical Society
Crochet Work, Tray Cloth, Mat and Cuff off-cut all with crochet edging. Belonged to the Maggs Family Ringwood. Examples of crocheting and Hardanger work.c1940's, c. 1940s
Belonged to the Maggs Family. Examples of crocheting and Hardanger work.Three pieces of work with crochet edging:; 1. Tray Cloth with cotton diamond pattern edging.; 2. Mat with fan and shell cotton edging and Handanger drawn thread work.; 3. Diamond edging on cuff cut off a sleeve. -
Flagstaff Hill Maritime Museum and Village
Domestic object - Wooden Rolling Pin, First half of 20th Century
A rolling pin is a simple tool used to flatten dough. The first civilisation known to have used the rolling pin was the Etruscans. Their advanced farming ability, along with a tendency to cultivate many plants and animals never before used as food and turn them into sophisticated recipes, were passed to invading Greeks, Romans, and Western Europeans. Thanks to the Etruscans, these cultures are associated with gourmet cooking. To prepare their inventive foods, the Etruscans also developed a wide range of cooking tools, including the rolling pin. Although written recipes did not exist until the fourth century B.C., the Etruscans documented their love of food and its preparation in murals, on vases, and on the walls of their tombs. Cooking wares are displayed with pride; rolling pins appear to have been used first to thin-roll pasta that was shaped with cutting wheels. They also used rolling pins to make bread (which they called puls) from the large number of grains they grew. Natives of the Americas used more primitive bread-making tools that are favoured and unchanged in many villages. Chefs who try to use genuine methods to preserve recipes are also interested in both materials and tools. Hands are used as "rolling pins" for flattening dough against a surface, but also for tossing soft dough between the cook's two hands until it enlarges and thins by handling and gravity. Tortillas are probably the most familiar bread made this way. Over the centuries, rolling pins have been made of many different materials, including long cylinders of baked clay, smooth branches with the bark removed, and glass bottles. As the development of breads and pastries spread from Southern to Western and Northern Europe, wood from local forests was cut and finished for use as rolling pins. The French perfected the solid hardwood pin with tapered ends to roll pastry that is thick in the middle; its weight makes rolling easier. The French also use marble rolling pins for buttery dough worked on a marble slab. Glass is still popular; in Italy, full wine bottles that have been chilled make ideal rolling pins because they are heavy and cool the dough. Countries known for their ceramics make porcelain rolling pins with beautiful decorations painted on the rolling surface; their hollow centres can be filled with cold water (the same principle as the wine bottle), and cork or plastic stoppers cap the ends. Designs for most rolling pins follow long-established practices, although some unusual styles and materials are made and used. Within the family of wooden rolling pins, long and short versions are made as well as those that are solid cylinders (one-piece rolling pins) instead of the familiar style with handles. Very short pins called mini rolling pins make use of short lengths of wood and are useful for one-handed rolling and popular with children and collectors. Mini pins ranging from 5 to 7 in (12.7-17.8 cm) in length are called texturing tools and are produced to create steam holes and decorations in pastry and pie crusts; crafters also use them to imprint clay for art projects. These mini pins are made of hardwoods (usually maple) or plastic. Wood handles are supplied for both wood and plastic tools, however. Blown glass rolling pins are made with straight walls and are solid or hollow. Ceramic rolling pins are also produced in hollow form, and glass and ceramic models can be filled with water and plugged with stoppers. Tapered glass rolling pins with stoppers were made for many centuries when salt imports and exports were prohibited or heavily taxed. The rolling pin containers disguised the true contents. The straight-sided cylinder is a more recent development, although tapered glass pins are still common craft projects made by cutting two wine bottles in half and sealing the two ends together so that the necks serve as handles at each end.Tiny rolling pins are also twisted into shape using formed wire. The pins will not flatten and smooth pastry, and the handles do not turn. The metal pins are popular as kitchen decorations and also to hang pots, pans, and potholders. https://www.encyclopedia.com/sports-and-everyday-life/food-and-drink/food-and-cooking/rolling-pinThe use of the rolling pin to make thin pastry or pasta.Wooden rolling pin with some damage on cylinder section.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, rolling pin, cooking, pastry -
Flagstaff Hill Maritime Museum and Village
Wood sample, 1855
The artefact is a piece of ship’s timber from the wreck-site of the SCHOMBERG, a vessel which collided with the Peterborough reef on her maiden voyage in December 1855. This small wooden remnant of the disaster has been concreted on one side by the accrual of marine sediment while submerged. The build-up of sediment over the remains of the vessel is typical of the site as a whole. This artefact illustrates the reclaiming power of the ocean and the gradual disappearance of timber constructed vessels that have come to grief along this coastline (for example, the THISTLE in 1837, and the CHILDREN in 1838). The SCHOMBERG was a 2,000 ton clipper ship, specifically designed for the Australian immigration trade (back-loading wool for Britain’s mills), and constructed in Hall’s shipyard in Aberdeen, Scotland. She was owned by the Black Ball Line and launched in 1855. Alexander Hall & Son were renowned builders of sleek and fast 1,000 ton clippers for the China trade (opium in, tea out) and were keen to show they could also outclass the big North American ships built by Donald Mackay. Consequently the SCHOMBERG was ‘overbuilt’. Her hull featured five ‘skins’ of Scotch Larch and Pitch Pine overlaying each other in a diagonal pattern against a stout frame of British Oak. Oak has been favoured by builders of wooden ships for centuries. Its close, dense grain made it harder to work, but also gave it great strength and durability. In addition, the lateral spread of its branches supplied a natural curvature for the ribs of a vessel’s hull, as well as providing the small corner or curved pieces (‘knees’ and ‘elbows’) that fit them together. The shape and texture of this wood sample suggests a dense hardwood like Oak. The timber has been cut off at one end since its recovery from the sea, exposing a smooth and almost shiny surface. Seasoned English Oak has a similar light brown colour and tight grained finish. At the launch the SCHOMBERG’s 34 year old master, Captain ‘Bully’ Forbes, had promised Melbourne in 60 days, "with or without the help of God." James Nicol Forbes was born in Aberdeen in 1821 and rose to fame with his record-breaking voyages on the famous Black Ball Line ships; MARCO POLO and LIGHTNING. In 1852 in the MARCO POLO he made the record passage from London to Melbourne in 68 days. There were 53 deaths on the voyage but the great news was of the record passage by the master. In 1954 Captain Forbes took the clipper LIGHTNING to Melbourne in 76 days and back in 63 days, this was never beaten by a sailing ship. He often drove his crew and ship to breaking point to beat his own records. He cared little for the comfort of the passengers. On this, the SCHOMBERG’s maiden voyage, he was going to break records. SCHOMBERG departed Liverpool on her maiden voyage on 6 October 1855 flying the sign “Sixty Days to Melbourne”. She departed with 430 passengers and 3000 tons cargo including iron rails and equipment intended to build the Melbourne to Geelong Railway and a bridge over the Yarra from Melbourne to Hawthorn. She also carried a cow for fresh milk, pens for fowls and pigs, 90,000 gallons of water for washing and drinking. It also carried 17,000 letters and 31,800 newspapers. The ship and cargo was insured for $300,000, a fortune for the time. The winds were poor as she sailed across the equator, slowing SCHOMBERG’s journey considerably. Land was first sighted on Christmas Day, at Cape Bridgewater near Portland, and Captain Forbes followed the coastline towards Melbourne. Forbes was said to be playing cards when called by the Third Mate Henry Keen, who reported land about 3 miles off, Due in large part to the captain's regarding a card game as more important than his ship, it eventually ran aground on a sand spit near Curdie's Inlet (about 56 km west of Cape Otway) on 26 December 1855, 78 days after leaving Liverpool. The sand spit and the currents were not marked on Forbes’s map. Overnight, the crew launched a lifeboat to find a safe place to land the ship’s passengers. The scouting party returned to SCHOMBERG and advised Forbes that it was best to wait until morning because the rough seas could easily overturn the small lifeboats. The ship’s Chief Officer spotted SS QUEEN at dawn and signalled the steamer. The master of the SS QUEEN approached the stranded vessel and all of SCHOMBERG’s passengers and crew were able to disembark safely. The SCHOMBERG was lost and with her, Forbes’ reputation. The Black Ball Line’s Melbourne agent sent a steamer to retrieve the passengers’ baggage from the SCHOMBERG. Other steamers helped unload her cargo until the weather changed and prevented the salvage teams from accessing the ship. Later one plunderer found a case of Wellington boots, but alas, all were for the left foot! Local merchants Manifold & Bostock bought the wreck and cargo, but did not attempt to salvage the cargo still on board the ship. They eventually sold it on to a Melbourne businessman and two seafarers. In 1864 after two of the men drowned when they tried to reach SCHOMBERG, salvage efforts were abandoned. Parts of the SCHOMBERG were washed ashore on the south island of New Zealand in 1870, nearly 15 years after the wreck. The wreck now lies in 825 metres of water. Although the woodwork is mostly disintegrated the shape of the ship can still be seen due to the remaining railway irons, girders and the ship’s frame. A variety of goods and materials can be seen scattered about nearby. Flagstaff Hill holds many items salvaged from the SCHOMBERG including a ciborium (in which a diamond ring was concealed), communion set, ship fittings and equipment, personal effects, a lithograph, tickets and photograph from the SCHOMBERG. One of the SCHOMBERG bells is in the Warrnambool Library. The SCHOMBERG collection as a whole is of historical and archaeological significance at a State level, listed on the Victorian Heritage Register VHR S612. Flagstaff Hill’s collection of artefacts from the SCHOMBERG is significant for its association with the Victorian Heritage Registered shipwreck. The collection is primarily significant because of the relationship between the objects, as together they have a high potential to interpret the story of the SCHOMBERG. The SCHOMBERG collection is archaeologically significant as the remains of an international passenger ship. The shipwreck collection is historically significant for representing aspects of Victoria’s shipping history and its potential to interpret sub-theme 1.5 of Victoria’s Framework of Historical Themes (living with natural processes). The collection is also historically significant for its association with the shipwreck and the ship, which was designed to be fastest and most luxurious of its day. The SCHOMBERG collection meets the following criteria for assessment: Criterion A: Importance to the course, or pattern, of Victoria’s cultural history. Criterion B: Possession of uncommon, rare or endangered aspects of Victoria’s cultural history. Criterion C: Potential to yield information that will contribute to an understanding of Victoria’s cultural history. A piece of wood, concreted in sediment, from the wreck of the SCHOMBERG (1855). The limestone accretion includes sand, shell grit and marine worm casings. The exposed surface of the wood is broken and worn smooth along the grain. One end of the timber has been cut or sawn off across the grain, presenting a smooth and shiny surface.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, wood segment, schomberg, shipwreck timber, alexander hall and son, limestone concretion, oak-framed hull -
Bendigo Military Museum
Literary work - PAMPHLET, Advice to Personnel Discharged During the War, 7.1945
RAAF pamphlet No 25 issued by the Rehabilitation Section of the RAAF to provide advice to personnel discharged during WWII. Item re Frederick Gardner DAVEY DFC No 410533 RAAF. Refer Reg No 3536P for his service details.Brown, card cover. 16 cut edged pages with black print on all. Pages stapled to the cover. Title on cover.rehabilitation, raaf -
Bendigo Military Museum
Literary work - BOOK, 1) Hold Hard, Cobbers Vol. 1 1912 - 1930 .2) Hold Hard, Cobbers Vol 2 1930 -1990, 1992
Two volumes detailing the story of the 57th, 60th and 57/60th Australian Infantry Battalions from 1912 to 1990. Donated by Frederick Ernest Addlem VX142253 57/60th Batt Refer Cat No 432.2 for his service history and 937P.Both volumes of Hold Hard, Cobbers. Both are hardcover with illustrations and illustrated dust jackets. .1 288 page, cut edged. Brown buckram and brown dust jacket. .2 352 page, cut edged. Green buckram with green dust jacket.Both items, on front end paper "Presented from the 57/60 Battalion (AIF) Association to the Bendigo RSL by Fred Addlem 1996"books, military, ww2 -
Bendigo Military Museum
Book - BOOK, POW’S, Organised by JP, The Death Railway & River Kwai Bridge
Book details the construction of the Thai Burma Railway & the bridge over the Rivew Kwai. Contains detailed photos & drawings. Taken from an oration by Fred Seiker in which he recalls the conditions under which the POW's lived & worked.Soft cover illustrated front & back with colour & black & white photos. 60 pages with cut edges. Bound with staples. Stamped inside front & back covers: Bendigo District RSL Sub Branch books-military-history, civil engineering/railways, river kwai, burma -
Bendigo Military Museum
Book - BOOK WW1, Big Sky Publishing Pty Ltd, ANZAC Sons, 2014
The story of Five brothers in the war to end all wars. ANZAC Sons is composed from a collection of over 5 hundred letters & postcards written by the brothers who served.. This compelling true story was compiled by the grand daughter of a surviving brother.Soft cardboard cover, red & black print on front, spine & back. Sepia photo of five soldiers in uniform on front cover together with black & white photo of a trench scene. Back cover has a black & white photo of soldiers & a building. 688 pages, cut plain paper, illustrated with black & white photos & maps. Collection of letters & postcards.Front fly leaf handwritten in black ink: “The Bendigo RSL Museum.Thank you for the inspiring work you do to ensure future generations will always remember the great sacrifices of our forebears. Allison”books-biography, military history-army, photography-photographs, anzac, sons -
Bendigo Military Museum
Book - BOOK, MARITIME, Arthur E Woodley, Western Port Wrecks & Maritime Mishaps, 1992
Soft cardboard cover. Brown print on front & spine, black print on back. Background colour aquamarine with front sepia photo of sailing ship. Back has 2 photos of the Cowes ferry. 103 pages, cut plain, off white. Illustrated with black & white photos & maps. Page XV has yellow highlighter pen applied to 2 sentences. Opposite p1, handwritten in blue ink on lined notepaper taped to page: “MIRANDA 1852, LADY MILDRED 1909, SEAGULL, CARPENTARIA, AT. * HARDWOOD. AIR. PORT, AMSTERDAM. FIVE (BEACHED), BUILT 1948. WORKED, YARRA RIVER, DIESEL MOTORS TOO BE RESTORED, * TOORADIN”book, maritime, wrecks, western port -
Bendigo Military Museum
Literary work - MANUSCRIPT, Bob Marmion, The Victorian Volunteer Force on the Central Victorian Goldfields 1858 - 1883
Photocopy of original held by Castlemaine Art Gallery & Historical Museum. The inscription is the Castlemaine Museum's Registration No & location code.Manuscript, M A Thesis. Plain A4 paper with cut edges, 144 pages with black & white illustrations. Pages secured with a metal clip.Page (ii) top R hand corner: “3247 S3 C/F5”documents - education, military history - volunteer forces -
Bendigo Military Museum
Literary work - DIARY WW1, It's About Jack, Post 2000
The diaries of PTE JOHN EDWIN BALL 3126A 48th Battalion 8th Reinforcement. Diary was transcribed by Michael Rohde, husband of J E Ball's grand daughter, Heather.Spiral bound with clear front cover & black card back cover. A4 plain paper with cut edges. 330 pages with black & white illustrations. Contains photocopies of original diary entries with typed transcripts.documents - diaries, military history, 48th -
Kiewa Valley Historical Society
Book - Student's Text, The Argus Students' Practical Notebook, 28/09/1948
Printed by the Argus and Australasian Limited in 1948 as a general text book for students. The Argus Newspaper had been printing interesting, informative and instructive articles on various phases of the work in schools every Saturday in their newspaper and the students were expected to cut these articles out and paste them in a convenient form for study and revision. The decision to publish the articles, by the Argus, in one volume was welcomed by the Director of Education, Victoria, J.A. Seitz and stated that it "can be recommended confidently to teachers and pupils."Gives a general overview of a lot of different subjects that students were being taught in the 1940's.It includes such areas as the three layers of government, simple mechanics and electrical theory, nature and general science. It is typical of what was being taught during the construction days in the Kiewa Valley and the owner would have possibly attended either the Tawonga State School or the Mt. Beauty State School. A green paper back text book of general knowledge. Contains nature notes, general science, Australian exploration, civics, and how the wheels go round. This is an Argus Production and the price is stated as two shillings.On the front cover, written in ink, is a name Helen Gunn, A1. This is repeated on the first page with two crosses underneath the inscription.argus newslpaper, general knowledge, education, pupils, text book -
Kiewa Valley Historical Society
Marking Gauge - Carpenter's Tool, c1925
Used from the mid 1920s to mark timber so that it could be cut with a saw. It was an essential tool for carpenters.Used by Alan Tyers who worked for the State Electricity Commission of Victoria on the Kiewa Hydro Electric Scheme.Carpenter's essential equipment. Used for marking timber so it can be cut with a saw. Wooden screw on the side allows the square wooden block to slide along the length of wood which is almost square at the end but with 2 flat sides and 2 rounded sides. Plated with 2 strips of brass on the square block. Sold for 1/3 in the 1920s. There is a nail through one end. carpenter, cabinet maker, secv, tool, marples, marking gauge -
Kiewa Valley Historical Society
Tin Snips - Tool
Used by builders and plumbers to cut tin.Used by Alan Tyers who worked for the State Electricity Commission of Victoria on the Kiewa Hydro Scheme.Cousin's Regular Pattern. Used by builders and plumbers to cut tin. Regular pattern with straight cutting edge. Best cast steel, black finish, ground blades. 9 inch. When closed blades meet at the point. Handles meet when closed and are curved outwards."J. Cousins & Sons. Sheffield"- Inscribed on handle side of pivot on one side.tinsmith, tin snips, tool, secv, cousin's & sons -
Yendon History Group
Framed pen and ink sketch of Yendon station, Mervyn Hill, 2010
Sketch was done as a sample of the artist's work when a drawing was sought to be the picture of the station on the interpretive sign planted at Yendon station. Although this is an excellent interpretation of the station building, it was thought to be too detailed for the purpose.Pen and ink detailed drawing of Yendon station building, with 2 people standing on the platform. Frame is timber, 50mm wide, mat black, with an 8mm silver trim around the cut-out hole.Signed by Mervyn Hill at the bottom right hand corner.yendon railway station, hill, mervyn, ink drawing