Lamp hanger nickel plated with 2xframes to hold shade, 1xextension fitting to fit to ceiling, 1xbrass burner with new wick.no marking. Patented design 1920-1950

Glass lamp base - seven sided narrowing before kerosene covered bowl section covered with brass burner possibly ' Aladdin' with used wick. Middle rim patterned - molded glass. Chimney - clear glass undamaged. Made around 1920's - 1950's.

The Adlake Non Sweating Lamp "THE ADLAKE NON SWEATING LAMP CHICAGO" Adlake is a shortened name of the "Adams and Westlake" company. They began doing business in 1857 in Chicago. They manufactured railroad supplies and hardware in Chicago. In 1927, they moved to Elkhart, Indiana, where they remain in business today. The difference between "lamp" and "lantern" is that the lamp is meant to be hung on a post or a hook during use and the lantern is hand-held and only used when a person is directing traffic. It has four lenses- two amber and two blue. Adams & Westlake, also known as A&W or Adlake, became a dominant maker of short-globe lanterns and their #200, #250, and plain “Kero” (sometimes known as #300 or #400) models were sold by the thousands to the entire range of railroads. Short-globe lanterns came about because manufacturers figured out how to get a lantern to burn properly with a shorter combustion chamber, which allowed lanterns to be shorter and cheaper. Adams & Westlake began selling #200 Kero lanterns around 1921 and they sold well, the #250 Kero lantern was released in the mid 1920’s as an improvement over the #200 version, with a new burner design. FInally, around 1930 Adams & Westlake released models marked simply “Kero” but are sometimes known as the #300 or #400 models, which are further refinements. The #200, #250, and “Kero” models all look very similar in design and in fact they are all pretty much the same frame design with a couple of minor differences on the later “Kero” models. Short globe lanterns are still very easy to find because they were produced well into the mid 1900s. Adams & Westlake short globe lanterns can usually be dated by looking for a two-part date code on the bottom of the lantern. The first digit will be 1,2,3, or 4 followed by a dash and then a two digit number. Sample code: 2-39 would mean that the lantern was produced in the 2nd quarter (Apr-Jun) of 193Historic - Railways - Adlake Non Sweating LampAdlake Non Sweating Lamp made of metal and glass Metal with handle, painted black, oil Bullseye lens, 13 cm diameter, green Circular lens on opposite site, 5 cm diameter, clear Sliding panel provides access to burner Rain shield embossed 'THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON''THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON'puffing billy, adlake non sweating lamp

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

Four NSWTD Railway marker Oil lamps at Nobelius Packing shed Item stamped numbers unknown Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil LampFour NSWTD Railway marker Oil lamps made of metal and glass Railway lamp, paraffin, metal / glass / fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870-1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTDpuffing billy railway , pbr, four nswtd railway marker oil lamps

Rail signal lamp, probably used an oil burner, before electricity was used. This item is missing the glass lens and oil burner. Victorian Railways rail train brass lantern signal bull''s eye lamp.Nonerailway lantern, signalman's lamp

Kerosene lamp used on buggies. Has copper cylindrical base to store kerosene. Has ornate burner inside a chamber with glasss on two sides, a tin guard on one side and a small red lens on another side. It has a two tiered square tin top for ventilation.buggy, lamp, lantern, kerosene

Lmap was hung in the old Malmsbury HotelSpherical shaped lamp made of tin, decorative features on this part, which holds the kerosene. Protruding from either side are two kerosene burners (no glass with this lamp). Lamp has a large handle lamp, lantern, kerosene

Yellow painted metal kerosene lamp has cylindrical container for fuel at the base and an upright piece at the back with a tin circular reflector. On top of the fuel container is a wick-burner (no glass cover)V inside a "three-leaf clover" Made in Englandkerosene, lamp

Metal (silver-plated?) cylindrical base with a column rising up to a cylindrical storage area for kerosene. On top of this are three wires protruding out from the burner area. These wires would be used to hold the glass lens (not with the lamp)lamp, lantern, light, kerosene

Guards lamp - of the type used by the Victorian Railways to give a green, red or clear or white signal while shunting or authorising trains to proceed. Used by station staff, shunters, guards and signal men.While not directly related to Ballarat tramways, of the type used by the Railways in the Ballarat district.Hand Lamp, Guards - Exterior casing of a black painted metal railway signal lamp with circular blue (for green colour) and red glass filters and a turning mechanism on the top under a circular handle. Includes the kerosene burner with wick and reflector plate. Item was specifically donated to the Museum by a member who died May 2022.railways, lamps, signals, guards

Table lamp with tubular wick, paraffin. Cast brass decorative base with four feet, cast brass interior and burner, with glass exterior and covering. Pink and white base colours on glass, with floral pattern printed on both sides of lamp. Cover a semi-circular shape with round neck opening on top.… Success…' (some words unreadable) embossed on burner platelighting, kerosene & oil, table lamp, brass, glass, paraffin, floral

f. Argand burner, with base and lamp housing

It was used as a bedroom lamp by Valmae (Colling) Gaudion in various railway houses lived in around Victoria in the days before electricity.A bedroom oil lamp with a light amber coloured glass bowl with a ring holder and blue oil inside. It has a green glass handle, a metal burner, cotton wick and a knob to adjust the flame. The chimney is clear glass with a decorated edge on the top.lamps, oil lamps

The heavy twin tanks formerly contained vaporised kerosene which was used as a fuel to light the lantern. Kerosene became available in the 1860s as the oil industry in the United States developed, and vaporised kerosene soon became the most common system of illumination. The kerosene vapour lamp was perfected by Chance Bros. for burning the light in their renowned lenses. The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. Kerosene tanks like these were developed in the early twentieth century, and kerosene as a fuel was phased out by electricity, with the last kerosene system in Australia eventually replaced in 1985. The wick lamp in Gabo Island’s light was altered to a vaporised incandescent kerosene mantle burner in 1909. They would have been in use until 1935, when the light was electrified and the original first-order lens was replaced by a fourth-order lens. The Gabo Island tanks, which are presumed to be those used in the lighthouse between 1909 and 1935, are not attached to the optical apparatus and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. Cape Schanck has a pair of unattached tanks, which are not historically associated with the lighthouse. Point Hicks has an iron stand that formerly supported its lighthouse oil tanks. Despite their lack of intactness, the Gabo Island tanks have first level contributory significance for their provenance to the lightstation and historic association with the lantern’s original Chance Brothers first order lens, which was removed in 1935Two large green cylinders standing in a metal frame. There is also a pumping mechanism attached to the stand with a wooden handle.

Was the stand for a Chance Brothers air & oil containers fitted with pump handle & pressure gauges.This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness. The oil was fed under pressure to the burner mantle. It is all that remains of an air and kerosene oil tank installation, with each rounded side formerly supporting a heavy iron tank. The containers would have been fitted with a pump handle and pressure gauges. An intact assemblage is displayed in the AMSA offices, Canberra with a text that explains ‘This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness’.The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The use of kerosene as a fuel to light the lantern became the most common system of illumination from the 1860s after the oil industry in the United States began to develop. The kerosene vapour burner was created in 1901 by British inventor Arthur Kitson (1859-1937) and perfected by Chance Bros for burning a more intense light in their renowned lenses. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. The Point Hicks lantern was initially lit by a six-wick Trinity house kerosene burner. This was replaced by the more efficient and brighter 55mm vaporised kerosene mantle burner in 1905, and the tank stand is probably original to this apparatus. Electricity eventually replaced kerosene at Point Hicks in 1964 making the tank installation obsolete, and the last kerosene system in an Australian lighthouse was replaced in 1985. Gabo Island Lightstation has a pair of tanks that are not attached to the optical system and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. An intact tank assemblage is displayed at the Cape Schanck Lighthouse Museum it is detached and not original to the lighthouse. Although corroded, the remnant Point Hicks tank stand has first level contributory importance to the lightstation. It is significant for its provenance and historical value as part of the Chance Bros vaporised kerosene burner introduced in 1905 to intensify the light and improve the efficiency of the system. The rusted iron stand rests on four short legs and is shaped like a pair of spectacles.

Kerosene lamps were used as a main source of lighting throughout Australia prior to the supply of domestic electrical services. This was obviously later in many rural areas. This lamp was used in the home of Mrs. Gina Elizabeth Harris of Bethanga in Northeast Victoria where electricity was connected on 23 March 1959.This lamp is representative of the lamps used throughout Australia prior to the introduction of domestic electricity supplies. This vintage kerosene lamp is model No. 21 which was manufactured by Aladdin Industries in Greenford, Middlesex, England in the 1950s. Base stems were mostly made from wood, turned into several different patterns. More expensive table lamp stems were of metal. Bases were mostly steel filled with sand as a weight. When Bakelite became available it was used extensively in three different colours, although collectors say that white bases were used primarily in hospitals and churches and are more rare. On wick knob: "21/Aladdin Industries Ltd/GREENFORD" Inscribed around burner: "GB Patent No 9. 69-4273-4"kerosene lamp, bakelite, domestic appliances

This is a typical example of a flat wick domestic paraffin lamp used in households prior to the introduction of electricity.A flat-wick lamp is a simple type of paraffin lamp, which burns paraffin drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce. The wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the wick. This has a cooling effect and keeps the wick from over heating. The lamp burner has a flat wick, made of cotton. The lower part of the wick dips into the fount and absorbs the paraffin; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the paraffin that the wick has absorbed burns and produces a clear, bright, yellow flame. As the paraffin burns, capillary action in the wick draws more kerosene up from the fuel tank. All paraffin flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above. (Source: Wikipedia accessed 24 Nov 2023) This lantern has a circular heavy green glass base for holding the paraffin. The base has a 12mm green glass handle. There is a small clear glass chimney with a fluted upper edge and some bubbles in the glass. The metal burner and wick holder has four metal prongs to hold the glass chimney in place. The round metal wick winder is functioning. There is a small amount of residual paraffin in the base. The flat wick is made of cotton.There are no markings to indicate the manufacturer.paraffin lamp, flat wick lamp, domestic lantern

Edward Miller started his business in Meriden, Connecticut, in the 1840's making and selling camphene and burning fluid burners. By the 1860's, Edward Miller had become an aggressive competitior in the lamp business. Edward Miller died in 1909 at the age of 82. The Miller Company continued to produce it's wares to his high standards and is still in existence today.Bicycle Lamp. Miller & Co. Miniature Kerosene Bicycle Lamp. Black Painted, metal. Approx. 60mm x 50mm x 120mm. Clear glass in front lens with a small faceted ruby glass lens on either side. Flexible hinged mounting mechanism at the rear of the lamp