This small cannon ball was found by the donor around 1975 to 1977 when he was digging a trench to install underground cables at the Warrnambool Surfside Caravan Park' Its location is just below both Cannon Hill and the 19th century Fortifications at Flagstaff Hill Maritime Museum and Village. The ball is made of iron. Cannon balls were used as ammunition for a cannon gun and fired at a target. This cannon ball is only 8 cm round, or 4.15 inches, and is likely to have been called a 4-pounder (4-pdr). The ball was made from molten iron was poured into the small opening of a two-piece mould. The seam between the moulds sometimes left a raised ring mark on the ball, as can be seen on this ball. The ridge would have been filed to make the join smooth, sometimes leaving a slightly flat area. Six 4-powder cannons were recovered from Endeavour Reef, Queensland, in 1969. They were from Captain Cook's HMS Endeavour, thrown overboard when the ship struck a reef there in 1770. They are likely to have been mounted on deck cannon carriages on the ship. Similar 4-pounder cannons were mounted on gun carriages and used as field guns. Cannons with cannon balls as ammunition were installed at Warrnambool for protection from possible invasion in the mid-to-late 19th century and early 20th century.Cannon ball, iron, black with a pitted shiny surface. It has three flat areas and evidence of a seam around the circumference. There are remnants of a possible inscription stamped into the iron. The cannon ball is a four-pounder ball. Imperial weight is 71 oz (201.3 gms or 4.44 pounds).Remnants of an indecipherable stamp and / or red text.flagstaff hill, flagstaff hill maritime museum and village, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, cannon ball, ammunition, cannon, fortifications, military equipment, firearm, weapon, two-piece mould, seam line, four-pounder, 4-pounder, field gun, field ammunition, gun carriage, cast cannon ball

Caulking iron narrow pointed jerry iron used to jerry or chip out the old pitch and oakum from corked seams. It was held at 45 degree angle to the seam and hit with mallet. Has JN&Co stamped both sides.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Caulking iron (hand made) narrow pointed jerry iron used to jerry or chip out the old pitch and oakum from corked seams. It was held at 45 degree angle to the seam and hit with mallet. 265mm long, 22mm wideflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, caulking iron

This broken black glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Black glass is one of the oldest bottle colours and dates back to the early 17th century. In the 1840s to late 1870s black glass bottles were mainly used for liquor and ale. All glass is made from silica, which is found in quartz sand. The naturally occurring sand has impurities, such as iron, that determine the colour of the glass. Residual iron leads to green or amber coloured glass, and carbon in the sand makes that glass appear as ‘black’. A strong light behind the glass will show its colour as dark green or dark amber. This handmade bottle appears to have been made in a three piece dip mould with a cylindrical base and two removable neck pieces. The molten glass was blown into the mould to give the body a uniform symmetrical shape and size. After the bottle was blown, the glassblower removed it from the mould then the base was pushed up with a pontil tool that gave it the concave shape. The finish for the mouth was added by hand or with another tool to form the ring collar. The mould gives the body a slightly textured surface. There is usually a line around the shoulder and on the sides of the neck where the mould meet, and a lump or mark in the centre of the base, called a pontil mark, where the push-up tool was removed. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, black glass. Mouth is broken off. Roughly applied ring collar. Bottle has shoulder seam and two neck seams. Heel is uneven, base is concave with tool mark. Glass has crease lines, a drip and imperfections. flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, black bottle, three pece mould

White full-length nylon nightgown. A tiny flower design is painted on to the fabric. Bodice has a V shaped cross-over bodice gathered onto a midriff band, 3.5 cms wide at the front and a V neckline at the back. Front and back tie together at the shoulders. A full-length gathered skirt has a 3 cms wide tie at the back waistline.Label on side-seam of skirt, near hemline reads: Hanro Quality Underwear SW Small Women’scostume, female underwear, nightgown

The bottle was probably used for holding ether as part of a doctors medical kit. The bottle has visible side mould seams on the shoulder which discontinues or fades at the lip, a tooled finish and the glass has bubbles. There is no pontil-scar or mark on the base of the bottle, but there is a circular mould seam on the base.Small square based glass bottle with round neck, possibly used to hold ether. Found inside carry box with other unrelated objects including brown stopper which does not fit in bottle. Appropriate stopper for glass bottle is not present.Small amount of brown residue inside bottle. Bubbles in side of glass. Brown marks on outer bottle. Scratches inside bottle neck. Glass stopper missing.dr [e.s.] holloway, bottle, glass

This handmade, aqua glass ink bottle's design is sometimes called a ‘boat’ shape. The base was mouth-blown into a rectangular mould, evidenced by the lack of seams, the pontil, crease lies and the uneven thickness of the glass. The shoulder section was mouth-blown into a two-piece mould and then cut off from the blowpipe. The lip is sometimes referred to as a 'burst-lip, which was often filed to be smooth. This method of making bottles was often used in the mid-to-late 19th century. The bottle would then be filled with ink and sealed with a cork. More expensive bottles would have a lip added, which was more time-consuming and costly. The capacity for a bottle such as this was about 3 ½ oz (ounces) equal to about 100 ml. Pens are a common item for that period. Pen and ink have been used for handwriting since about the seventh century. A quill pen made from a bird’s feather was used until the mid-19th century. In the 1850s a steel point nib for the dip pen was invented and could be manufactured on machines in large quantities. The nis only held a small amount of ink so users had to frequently dip the nib into an ink well for more ink. Handwriting left wet ink on the paper, so the blotting paper was carefully used to absorb the excess ink and prevent smudging. Ink could be purchased as a ready-to-use liquid or in powdered form, which needed to be mixed with water. In the 1880s a successful, portable fountain pen gave smooth-flowing ink and was easy to use. In the mid-20th century, the modern ballpoint pen was readily available and inexpensive, so the fountain pen lost its popularity. However, artisans continue to use nib pens to create beautiful calligraphy.The ink bottle is of interest, being made of aqua glass rather than the more common clear glass. This set of ink bottles and pens is significant because of the bottle's method of manufacture, which is representative of a 19th-century handcraft industry that has now been largely replaced by mass production. The bottle and pens are historically significant as tools used for handwritten communication until the mid-20th century when fountain pens and modern ballpoint pens became popular and convenient and mechanical typewriters became part of standard office equipment.Victorian 'Boat' ink bottle, small rectangular, aqua glass ink bottle with grooves along the long sides for pen rests. The base has a pontil, no seams, and the glass is uneven in thickness. The shoulder has two side seams and there is a ridge where it is joined onto the base; there are round indents on each of the shoulder, on the short sides, four in all. The mouth has rough edges. The neck leans to one side. The glass has impurities, crease lines and bubbles. There is dried ink in the bottle. Two pens with metal nibs are included with the ink bottle. flagstaff hill, warrnambool, maritime museum, maritime village, great ocean road, shipwreck coast, ink, nib pen, writing ink, writing, copying, banks, lawyers, commerce, student, permanent ink, stationery, record keeping, handwriting, writing equipment, writing accessory, office supply, cottage bottle, boat bottle, mouth-blown bottle, two-part mould, sheer-lip bottle, burst-lip, cork seal, copy ink, aqua glass

A tall, narrow, triangular-shaped clear glass bottle. The sides are flat and the base is triangular. It is seamed.Base- F3 + indecipherable numbers/letters At bottom - THIS BOTTLE MUST NOT BE USED AS A FOOD CONTAINERglass bottle

Australia was not self sufficient in glass making until the turn of the 20th century and many bottles were made overseas and shipped to Australia with their contents and when emptied were re-filled with other company’s products. This bottle have an aesthetic element in that the shapes is visually appealing. It reflects the type of glassware that was in circulation in the first half of the 20th century. A small clear glass bottle with a threaded neck. It has a mould seam from the rim to the base.On the base - 049 F1020bottle glass container

A small clear glass bottle with a chipped rim. It has a seam mould from the rim to the base.On the base - AGMbottle glass container australian-glass-manufacturers

A pair of Service Brown stocking with reinforced foot and top in lisle and leg of nylon with back seams.H Loyalty Service Weight Nylons by Holeproof 9-1/2costume, female, female underwear

Part of a selection of garments knitted by ‘Tina Knitwear’. Tina Knitwear was a successful made to order knitwear business in Brighton from the mid-1960s to around 2010, run by Assunta and Franco Liburti. Daughter Melissa Persi writes: Our parents Assunta (Mum) and Franco (Dad) Liburti ran a successful made to order knitwear business in Brighton from the mid-1960s to around 2010. Assunta was affectionately known to her family as Assuntina, therefore the business was named "Tina Knitwear" after her. Assunta and Franco were born in the beautiful seaside town of Terracina in Italy in 1933 and 1930 respectively. As was so common in Italy in the 1950s, Assunta who was in her late teens and early twenties learnt the intricate skills of machine knitting, dressmaking and pattern making. Franco on the other hand, learnt the building trade with his 2 brothers and specialised in bricklaying and tiling. As was so common after the war, Assunta and Franco yearned for a better life so they decided that they would get engaged and then migrate to Australia to be married and raise their family in Australia, a land of much opportunity which they no longer felt their beloved Italy held for them. Assunta migrated to Australia first in 1957 and later Franco joined her in 1958 where they were married. For the first few years, Franco (also known as Frank) worked as bricklayer /tiler on buildings such as the Robert Menzies building at Monash University in Clayton and various buildings in the Melbourne CBD. Assunta on the other hand put her machine knitting skills to use working in factories doing piece machine knitting for various knitwear companies. The hours were long, the conditions were difficult, and travel was onerous without a car. After their 2 older children were born, it was decided that dad would leave the building trade and they would start their own made to order knitwear business. That way they could work from home and raise their family together. Mum taught dad everything he needed to know so he could operate the knitwear machinery. They purchased COPPO knitting machines from Italy and a Linking machine from Germany. Initially they had a knitwear shopfront in Bay Street Brighton where a store assistant would take the orders and client’s measurements and Assunta would then make the garments from a small workshop in their home. Unfortunately, the assistants were not skilled dressmakers and often measurements and orders were incorrectly taken. Assunta being the perfectionist and highly skilled machinist that she was, decided that she needed to oversee the entire process from meeting the client, to taking their order, right thru to the fittings and completion of the garment. It therefore made sense that they should close the shop front and run their business from their own home in Brighton and hence “Tina Knitwear” was born. Together, for more than 40 years they ran their very respected and successful business and were well known in the Bayside area. They specialised in made to order knitwear for both men and women using mainly pure wool (from Patons, Wangaratta Mills, Japan and Italy) but also lurex and estacel. Over those years, many of their clients became their close friends. It wasn't unusual for clients to come to order garments and then end up in the kitchen chatting over a cup of Italian espresso coffee and homemade biscuits. Some of their clients were especially memorable and became lifelong friends. Mrs Connell was a dear friend of mum’s, each year she would buy tickets for the “Gown of the Year” fashion show. She would insist on taking Assunta and her 2 daughters so that we could see the latest fashions. Then there was their dear friend Ms Griffiths. She had been a Matron nurse at the Queen Victoria Hospital when she met my parents in the 1970s. She returned to live in New Zealand in the 1980s but came back to Melbourne every year to stay for 2 weeks with the sole purpose of visiting my parents (she adored them) and order garments. For those 2 solid weeks, mum and dad would only knit for Ms Griffiths and she would go back to New Zealand with at least 5 or 6 new outfits. I actually think she enjoyed mum’s homemade pasta almost as much as her new clothes! Over the years, my parents learnt to speak English very well given that majority of their clients were not Italian speaking. Their oldest child John born in 1960 learnt to speak English with the help of those clients who were such a big part of our childhood. Mum and dad always went above and beyond to ensure their clients were satisfied. Mum was an absolute perfectionist and it showed in her attention to detail and the quality of their beautiful work. You only need to look at the garments that have stood the test of time or speak to their clients to know that this is true. Their clients would always comment on how well their clothes would last and much of their clients came via word of mouth and recommendations. Occasionally there would be disagreements because mum had found an error in dad's knitting (either a wrong stitch or a sizing mistake mainly) and would ask him to redo a piece, he would argue back saying that it was fine, but we always knew who would win the argument and that the piece would get remade! Similarly, we recall discussions where mum would ask dad to find a particular colour of wool in the garage where the stock was kept. He would try to convince her that they were out of stock of that colour and that the client should choose a different colour. She would insist they had it and then after hours of searching, he would return into the house sheepishly holding the wool! Our childhood is full of beautiful memories of mum and dad always being present, clients coming and going, mum humming her favourite songs as she worked often late into the night and sometimes, we even fell asleep to the hum of the machinery. They put their heart and soul into "Tina Knitwear" and took pride in providing only the best quality garments for their clients. In Italian there is a saying “lei ha le mani d’oro” which literally translated means “she has hands of gold”. Franco enjoyed his work but for Assunta, it was more than just work and there is no better way to describe her skills, passion and dedication to her machine knitting… she truly did have “hands of gold”. We will forever be grateful that our parents’ life journey gave us the opportunity to live in a home filled with creativity, dedication and passion, amazing work ethic and mutual respect, lifelong friendships and a lifetime of love. Grey marle princess seam dress with v neck, centre back zip and long sleeves. knitwear, clothing, italy, migrants, brighton, knitting machine, linking machine, garments, business, family, community

Cream coloured fine cotton baby's petticoat. Cut in one piece with two side seams. No seam on shoulder. Slightly scooped neckline. Other shoulder fastened with one button. Hand crocheted trim on neckline, arm holes around hemline. Hand made.costume, children's, baby's petticoat

A small rectangular clear glass bottle with a threaded top. It has a mould seam from the rim to the base.On the base- AGM G510glass bottle container australian-glass-manufacturers

Vegemite hit the market in 1923 but failed to sell. In 1928 the company renamed its spread Parwill to compete against the top-selling British import, Marmite but Parwill flopped too. In 1922 the Fred Walker Company hired a chemist, Percy Callister, to develop a useful food from vitamin-rich used yeast being dumped by breweries. Using enzymes to split open the yeast cells, Callister extracted the contents and blended them with vegetables and salt into a sticky black paste with a sharp taste. They tried the Vegemite name again and gave the product away with Walker cheese products and a couple of cars as prizes before Australians finally fell for it. In 1939 Vegemite was officially endorsed by the British Medical Association as a good source of Vitamin B and was included in Australian Army rations during World War II. Buyers were now assured of the nutritional value of Vegemite, which has been a market leader ever since. The Fred Walker Company became the Kraft Walker Cheese Co. Pty Ltd in 1926 and Kraft Foods Limited in 1950. (from Powerhouse Museum) This type of jar was used to package Vegemite between 1935 and 1945. Vegemite has been an 'Australian icon' since World War II when it was recognised as one of the world's highest food sources of vitamin B. It was sent to war with the troops and rationed at home. The marketing strategy that put Vegemite in 9 out of every 10 Australian homes in the 1940s, 50s and 60s emphasised the value of Vegemite to children's health. A cylindrical Vegemite jar made of white opal glass. It has a threaded rim and two mould seams. On the base - AGM Vegemite V879

Item re Frederick Gardner DAVEY DFC No 410533 RAAF. Refer Cat No 3536P for his service details.Black hat band to fit RAAF dress cap. Woven fabric with seam sewn in black thread.head wear, hat, band

Grey silk stockings with seam up back of leg. Design on back of heel,toe and sole are cotton.costume, female, female underwear

This Japanese ceramic vase was recovered from the wreck of the S.S. Casino (1882 – 1932) between the late 1960s to early 1970s. It is one of the shipwreck artefacts in the John Chance Collection. The design is an example of vintage basket weave pottery. The base of the vase is stamped ‘MADE IN JAPAN’ , which dates its probable manufacture to circa 1921-1932. The vase has side seams indicating that it was made by joining two moulded sides of the vase together, then adding the round base. The coastal trader SS Casino (1882–1932) had a run of almost 50 years along the coast of Western Victoria. She traded goods and food as well as carrying passengers from port to port on her many voyages. This vase may have been included in her cargo or could have been amongst the personal luggage of the people on board. The ceramic vase is an example of ceramic pottery in Victoria the 1930s. The vase is also significant as it was recovered by John Chance, a diver from the wreck of the Loch Ard in the 1960s-70s. Items that come from several wrecks along Victoria's coast have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value. The vase is also significant as it is associated with the S.S. Casino, which played an historical role in Western Victoria, providing transport, communication and trade along the coast between Melbourne and Portland in the late 19th and the early 20th century, visiting the ports at Apollo Bay, Warrnambool and Belfast (Port Fairy). The S.S. Casino was the only regular trader with normal passenger accommodation along the West Coast and the only Western District steamship that was in service between 1854 and 1939, and to be represented in the Victorian Heritage Shipwreck register, and to have been wrecked in the Western District, and to have the wreck located, and to be accessible to divers. The wreck of the S.S. Casino, and its associated relics, is considered an important part of Victorian and Australian cultural heritage and is now protected as a Historic Shipwreck under State and Commonwealth Law in the Commonwealth Historic Shipwrecks Act (1976). Vase, round, cream coloured, unglazed ceramic, basket weave design. Wide mouth, short neck that tapers out to wide shoulders and straight down to round base. Seams on each side, mouth to base. Small handle on each side of vase between mouth and shoulder. Front and back of vase have a plain oval space bordered by a floral design. Inscription stamped onto base. Made in Japan. Stamped onto base in black ink "MADE IN / JAPAN"flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, vase, japanese vase, s.s. casino, john chance, vintage pottery, newcastle and hunter river steam navigation company, belfast and koroit steam navigation company, west coast trader, apollo bay, captain middleton, basket weave, ceramic

An ink bottle was made of glass or ceramic and typically sat on a desk. The writer would dip the pen (or quill) into the bottle to put more ink on the pen. Because they sat on a desk, ink bottles were often decorative. We have mostly dispensed with ink bottles and quills. This item is an example of early stationery equipment commonly used in schools, households and commercial enterprises.A squat clear glass ink bottle which is square-shaped. It has threaded top and is seamed on both sides.on base - AGM F823 M P50container bottle ink-bottle

This refillable ink bottle would have been used extensively in the early 1900's before ballpoint pens were introduced.Ink bottles are rarely used today. This item is an example of early stationery equipment commonly used in schools, households and commercial enterprises.A clear glass ink bottle. It would have had a cork stopper. It is seamed on both sides and the shoulders are tiered.on front - 402 SWAN INK on base - indecipherable markingsink-bottle container glass-bottle

This item is an example of a glass food container used by an early Australian food manufacturing industry.A wide necked clear glass jar. It is seamed and has a circle on the base. There are some manufacturing signs near the bottom.In a diagonal banner across the glass - JONATHON REEVE PTY LTDglass jar jonathon-reeve food pickles-condiments

The Bocksbeutel ("goat's bag") bottle has been used since 1726 to store Franconian wines from south-east Germany. The Franken wine-growing region is in the north-west of Germany’s historic state of Bavaria. More than 40% of all Franken wines are bottled in the Bocksbeutel, which is often described as flagon-like in appearance. It is said that the bottle is so shaped to prevent it rolling away from its owner. Only Franken and nearby villages in northern Badenare allowed to use the Bocksbeutal, with selected areas in Portugal, Italyand Greece permitted to employ their own variations. (ref www,winesearcher)A bocksbeutel - a a flagon-shaped wine bottle in the form of a flattened ellipsoid. It is a clear green glass bottle which is seamed.Base - 3 8A 313 700 mlsbottle beverage wines bocksbeutel franken-wines

A small round opaque white glass jar. It has a threaded top and a mould seam from the rim to the base.jar white-glass container

Australia was not self sufficient in glass making until the turn of the 20th century and many bottles were made overseas and shipped to Australia with their contents and when emptied were re-filled with other company’s products. This bottle has an aesthetic element in that the shapes is visually appealing. It reflects the type of glassware that was in circulation in the first half of the 20th century. A small round clear glass bottle which has a mould seam from the rim to the base. The neck is lipped.bottle glass container

These type of gaiters were used by soldiers who would have been attached to the Light Horse Regiments. No other men other than soldiers in the Light Horse Regiments wore these gaiters as they were part of their uniform and added protection of their lower legs when riding their horses. All levels for AIF people wore these gaiter from Privates to Officers. There seems to be several types of gaiters which were lace ups or had straps over the outside of the gaiters or some were just done up with the buckles at the top. It is unknown it the ones we have would have had straps on the outside or if this was a choice of the wearer. Towards the end of WWI many of the light horse regiments combined with each other as their numbers became less and eventually with the advancement of military weapons the use of horses in war battles become less and were not needed in consequent world wars. These gaiters are historical significant to world war one and the light horse regiments especially the 4th and 13th Regiments. Men from the the Kiewa Valley went off to war and fought with the these regiments. Henry Higginson fought with both the 4th and 13th LHR in France. Sydney Stewart fought with the 4th LHR in France and was killed in France aged 20 years of age. A few of the young men that left from Tawonga in the Kiewa Valley went into the Light Horse Regiments as they were farmers that had experience with horse. Even though the AIF said they just did not automatically put country men into the LHR . Despite not having provenance of these gaiters the fact that men from Tawonga were in the light horse regiments, and only men from the LHR wore these gaiters it would be safe to say they would have been from some one in the local area that fought in WWI who owned these. Therefore they are representative of gaiters from the LHR and have excellent interpretive capacity as KVHS have a photo of Henry Higginson wearing his uniform which clearly shows his gaiters similar to these ones.One pair of brown leather gaiters with buckle at top. Seam at ankel. Left gaiter has strap missingmilitary, army, horse, gaiters