Double Headed Rail from Ravenswood Station Siding which was dismantled circa 1987 the two rails were stored for a time at Maldon before being donated to Puffing Billy Museum Bearing makers marks of Wilson & Cammell - Dronfield- Steel works Wilson & Cammell made Steel rails at their Dronfield Steel Works, in Dronfield, North East Derbyshire, England from 1872 - 1883 Double-headed rail In late 1830s Britain, railway lines had a vast range of different patterns. One of the earliest lines to use double-headed rail was the London and Birmingham Railway, which had offered a prize for the best design. This rail was supported by chairs and the head and foot of the rail had the same profile. The supposed advantage was that, when the head became worn, the rail could be turned over and re-used. In practice, this form of recycling was not very successful as the chair caused dents in the lower surface, and double-headed rail evolved into bullhead rail in which the head was more substantial than the foot. Info from Wikipedia - Rail Profile https://en.wikipedia.org/wiki/Rail_profile The first records of double headed rail being used In Victoria by Victorian Railways was in 1859, the rails, chairs, oak and trenails were imported from UK. After the 1870’s the Victorian Railways went over to using flat bottom rails, but they still needed replacement double headed rail for lines already laid and this continued up to at least 1883 Wilson & Cammell - Dronfield- Steel works Wilson & Cammell made Steel rails at their Dronfield Steel Works, in Dronfield England from 1872 - 1883 Mount Alexander & Murray River Railway The Melbourne, Mount Alexander & Murray River Railway Company received parliamentary assent in February 1853 to build Victoria's first inland railway from Melbourne to Williamstown, and Melbourne to Bendigo and Echuca. Construction commenced in January 1854 with work on a pier at Williamstown but lack of funds slowed progress, eventually prompting the company to sell out to the government. The 100-mile (162 km) section to Bendigo opened in October 1862. Its cost of £35,000 per mile made it the most expensive railway ever built in Australia. In 1864, the line was extended to Echuca, tapping into the booming Murray-Darling paddlesteamer trade. info from Museums Victoria - Victorian Railways https://museumsvictoria.com.au/railways/theme.aspx?lvl=3&IRN=450&gall=456 1863 Ravenswood Station open on the 1st Feb 1863 Victorian Railways - purchased and imported the Rail and Chairs from Raleigh, Dalgleish, White and Co. London Importation of railway plant : abstract of a return to an order of the Legislative Assembly dated 27th June 1860 for - Copies of the advertisements calling for tenders, the names of the tenderers and the accounts and correspondence with Mr Brunel relating thereto GP V 1859/60 no. C 15 http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoC15.pdf Report from the Select Committee upon the Importation of Railway Plant : together with proceedings of the Committee, minutes of evidence and appendix GP V 1859/60 no. D 38 (2.9 MB) http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoD38.pdf Ravenswood Siding When the Victorian Railways were established in 1856 they adopted one of the popular British permanent way standards - heavy 80lb (36.3kg) double-headed rail held up right in cast iron chairs attached to transverse timber sleepers by wooden pegs called trenails. The Ravenswood Railway siding was constructed in 1862 with 12 feet wrought iron double-head rail held in cast iron chairs with Ransom and May patent compressed keys. Trenails held the chairs to the sleepers and the joints were secured in joint chairs. Joints were subsequently joined using fish plates. It formed part of the Melbourne to Echuca rail line, initially known as the Melbourne, Mt Alexander and Murray River Railway. George Christian Derbyshire, the first Engineer-in-Chair of the Victorian Railways was responsible for the design and construction of the works. No new lines were built in Victoria using double-headed rail after 1870. The siding was disconnected from the main line in 1988. The Ravenswood Railway Siding demonstrates the original 1856 philosophy of the Victorian Railways to adopt British permanent way technology. The siding demonstrates significant aspects in the development of permanent way technology in England and Victoria over the period from the 1830's to the 1880's. The chairs in the Ravenswood siding are physical evidence of early railway technology rendered obsolete 120 years ago, namely joint chairs at rail joints and trenails to secure the chairs to the sleepers. The double-headed rail demonstrates an important stage in the evolution of British rail technology in the 1830s. The old fish plates, square headed bolts and square nuts demonstrate the success of fishing the rail joins. The Ravenswood siding demonstrates the earliest form of rail joint technology developed in England, and existing in Australia, the joint chair. In part of the siding the sequence of joint and intermediate chairs is consistent with the 1856 specifications, that sequence is rare with the joints secured in joint chairs. The survival of chairs in this sequence is rare and almost certainly demonstrates that they remained in continuous use at the same location from 1862 to 1988. This remnant of the Ravenswood siding has survived 126 years. The siding has proved to be the most significant of extant remnant double-headed sidings in Victoria, containing a rare combination of early permanent way technologies. Construction dates 1862, Info from Ravenswood Railway Siding Victorian Heritage Database Report http://vhd.heritagecouncil.vic.gov.au/places/4693/download-report The remaining section of this siding is significant at the State and National levels in that it demonstrates the use of chaired rail by the Victorian Railways Department for the Trunk Lines and, more particularly, the following stages in the evolution of this long obsolete method of permanent way construction: a) The use of joint chairs and intermediate chairs at regular intervals inferring that the original wrought iron rail lengths were 12 feet, as is known through documentary sources to have been the case. The survival of chairs in this sequence is unique and almost certainly demonstrates that they have remained in continuous use at the same location and in the same sequence from 1862 to 1988 . b) The use of joint chairs and intermediate chairs designed for use with trenails. c) The use of later intermediate chairs designed for use with steel pins and the use of fished joints with steel double head chaired rail, representing a second method of constructing the permanent way using chaired rail technology. info from Ravenswood Siding - Melbourne/Echuca Railway Line - Victorian Heritage Database Report http://vhd.heritagecouncil.vic.gov.au/places/70103/download-report Addition to Citation for Melbourne to EchucaRailway Line 1/10/1990 Double Head Rail The surviving lengths of double head rail with chairs on this railway compare with one surviving similar remnant on the Geelong to Ballarat railway and are representative of permanent way construction techniques applied exclusively to the two trunk railways of the 1860's. In this respect they are rare survivors and may be unique at the national level and of technical importance at the international level to the extent that they enhance contemporary understanding of early railway building technology. Surviving lengths of chaired double head rail survive at Kyneton, Ravenswood and Bendigo on this railway and include a number of different types of cast iron intermediate and joint chairs with hardwood keys and metal pins. The Ravenswood siding is of special significance for the diversity of chair types and for the sequence of chairs recalling rail lengths known to be associated with construction of the line in 1862. Construction of the Railway Tenders closed on 24 March 1858 with no less than 133 tenders being received. A contract was let to Cornish and Bruce for £3,356,937 to commence work on 1 June 1858 and complete the line by 31 July 1861. Cornish and Bruce made quick early progress with the Melbourne to Sunbury section being officially opened on 13 January 1859. The line was officially opened to Bendigo (Sandhurst) on 20 October 1862 by the Governor of Victoria, Sir Henry Barkly. A great banquet was held for 800 guests and this was followed by a grand ball. The extension of the line to Echuca was a relatively simple matter as that part of the line was across plain country without any significant engineering challenges. Tenders were called for the work in 1863 and the work was completed in 1864 by contractors Collier and Barry Apart from the line contractors, other firms directly involved were J Shire law and Co (sleepers), R Fulton, Langlands Brothers and Co, William Crossley (water supply), B Moreland, Langlands Brothers and Co (platelayers lorries), E Chambers (iron pins, traversers), Miller and McQuinstan (luggage vans and steam engines) and various contractors for building works. Info from Engineers Australia Engineering Heritage Victoria Nomination for Recognition under the Engineering Heritage Australia Heritage Recognition Program for the Goldfields Railways - Melbourne , Bendigo & Echuca Railway Page 25 - .2.9.2 Statement from National Trust of Australia (Victoria) Listing number B5323 for Mt Alexander/Murray Valley Rail Line: Page 69 - Theme 3 https://www.engineersaustralia.org.au/portal/system/files/engineering-heritage-australia/nomination-title/Melbourne_%20Bendigo_Echuca%20Railway%20Nomination.pdf The Melbourne, Mount Alexander and Murray River Railway Company was a railway company in Victoria, Australia. It was established on 8 February 1853 to build a railway from Melbourne to Echuca on the Victorian-NSW border and a branch railway to Williamstown. The company struggled to make any progress and on 23 May 1856, the colonial Government took over the Company and it became part of the newly established Department of Railways, part of the Board of Land and Works. The Department of Railways became Victorian Railways in 1859. Construction of the Bendigo line commenced in 1858, but this private consortium also met with financial difficulties when it was unable to raise sufficient funds, and was bought out by the Victorian colonial government. The design work was then taken over by Captain Andrew Clarke, R. E., Surveyor-General of Victoria, with bridge designs completed by Bryson and O'Hara The contract for the first stage of the line from Footscray to Sandhurst (now Bendigo), was let to Cornish and Bruce for £3,356,937.2s.2d ($6.714 million) with work commencing on 1 June 1858. Completion of the permanent way was to be by 31 July 1861 https://en.wikipedia.org/wiki/Melbourne,_Mount_Alexander_and_Murray_River_Railway_Company Victorian Railways - purchased and imported the Rail and Chairs from Raleigh, Dalgleish, White and Co. London Importation of railway plant : abstract of a return to an order of the Legislative Assembly dated 27th June 1860 for - Copies of the advertisements calling for tenders, the names of the tenderers and the accounts and correspondence with Mr Brunel relating thereto GP V 1859/60 no. C 15 http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoC15.pdf Report from the Select Committee upon the Importation of Railway Plant : together with proceedings of the Committee, minutes of evidence and appendix GP V 1859/60 no. D 38 (2.9 MB) http://www.parliament.vic.gov.au/papers/govpub/VPARL1859-60NoD38.pdf Victorian Railways : report of the Board of Land and Works November 1862 GP V 1862/63 no. 21 (2.8 MB) https://www.parliament.vic.gov.au/papers/govpub/VPARL1862-63No21.pdfHistoric - Victorian Railways - Double Headed rail Ravenswood Railway Station and Siding Victorian Heritage Database Reports Victorian Heritage Register VHR H1100 Victorian Heritage Register VHR H1786 National Trust VHR H1100 Mount Alexander and Murray River Rail way Line National Trust2 rail lengths of Double Headed Rail made of Iron makers marks : Wilson & Cammell - Dronfield - Steel and 20 joint chairs with metal rail pins Makers mark Wilson & Cammell - Dronfield - Steel (possible date 187? very hard to read ) puffing billy, double headed rail, wilson & cammell - dronfield - steel works, ravenswood station siding, melbourne to echuca rail line, initially known as the melbourne, mt alexander and murray river railway.

Rail tractors were popular with Victorian sawmillers. They were generally cheaper than a steam locomotive, required no special qualifications to drive, and used proven power plants for which spares were available locally. The tractor was constructed by Day’s Engineering of South Melbourne which, although better known for its pumping equipment, built more than fifty rail tractors for Victorian sawmillers and other industrial tramway users. W. Day & Sons is believed to have constructed its first light railway locomotive in 1926. From then until the mid 1940s, the firm appears to have built at least fifty locomotives at its premises in South Melbourne, of which roughly half were four-wheel locomotives and roughly half were six-wheel locomotives like the restored Day’s rail tractor formerly operated by Ruoak Timbers. Of the four-wheel locomotives, ten were 2-ft (610mm) gauge locomotives similar to this one. Today, only two survive, a complete example at the Puffing Billy Railway Museum at Menzies Creek, and one at Alexandra Timber Tramway Museum This 2-ft gauge 4wPM locomotive is believed to have been one of two Day's Petrol Rail tractors formerly used by Cheetham Salt, possibly at the Moolap works near Geelong. Service History :owned by Cheetham Salt, Moolap ( dates unknown ) Geelong Steam Preservation Society , Belmont 1973 ? Puffing Billy Steam Museum , Menzies Creek Historic - Industrial Narrow gauge Railway - Rail Tractor used by Cheetham Salt Company works at Laverton, Moolap and Geelong, Victoria , Australia Petrol Rail Tractor made of Iron , wrought iron, steel puffing billy, industrial narrow gauge railway, rail tractor, days engineering, cheetham salt,, petrol rail tractor

Trench art letter opener cut into the shape of a scimitar from a section of a shell case. The handle for the letter opener is made from a discharged British or Australian MK VII .303 calibre rimmed cartridge. The blade of the letter opener is attached to the handle via a bullet which has been sliced through the middle HMAS Uralba was an auxiliary minefield tender and armament stores carrier operated by the Royal Australian Navy (RAN) during World War II. She was launched in 1942 by Ernest Wright, Tuncurry, New South Wales as Uralba for the North Coast Steam Navigation Company. Requisitioned by the RAN while under construction on 13 July 1942 and commissioned on 22 November 1942. After being returned to her owners and being sold and used for a number of purposes she was sunk on 4 November 1971 to create an artificial reef off Carrum Creek, in Port Phillip Bay.Stainless steel blade with handle made from 303 round/cartridgeHMAS Uralba inscribed on bladehmas uralba, ran, ww2, letter opener, paper knife

The play was presented by arrangement with NIDA, The play was originally dramatized by Bert Bailey from the works of Australian writer Steele Rudd.The program includes information about Australian writer Steele Rudd and the original play. Garry McDonald best known as 'Norman Gunston' plays eldest son Dave.on our selection, athenaeum theatre, program, melbourne theatre company, bert bailey, garry mcdonald

This 35mm Westrex 14 projector was purchased from Waverley Theatre (Cnr Burke Road and Waverley Road in Malvern, in 1962) last used by "Cosmopolitan Motion Pictures" as follows: from 1962 to 1967 - National Theatre, Richmond. from 1967 to 1970 - in a small leatherette on Bridge Road, Richmond. from 1971 to 1985 - Galaxy Theatre Brunswick. After that it was stored at the back of Westgarth Theatre in Northcote. This projector has a primary historic significance as it covers the largest part of the history of film shows by "Cosmopolitan Motion Pictures", and cultural/social significance since it has been used to project a number of other language films (about 10 different languages) by the company. It also carries a secondary significance of rarity being the last used projector by the company at Galaxy Theatre.This metal (most probably steel) projector is part of a number of projectors owned by "Cosmopolitan Motion Pictures". It is in dark blue/grey colour and still operational to project 35mm films if needed. It has two inscriptions detailed below and was last used at Liberty/Galaxy Theatre in Brunswick in 1985 (for more details about the history of Galaxy Theatre follow this link http://technicolouryawn.com/?page_id=2988)INSCRIPTION 1 (red background) Westrex 14, High Intensity Arc Lamp, Serial Number A.5401018. Manufactured for Westrex (Australia) Pty. Limited by G.B.H. Electronic Laboratories - Made in N.S.W. Australia INSCRIPTION 2 (blue background) Westrex R4A Reproducer Made in Australia Western Electric Co. (Aust) Pty. Ltd.projector, film, culture, language, greek, entertainment, γιαννούδης, yiannoudes, προβολέας

A wooden racquet with an open throat, split by a steel threading shaft, with inscription: CRAVEN. PAT. The base of the head on both sides features the decal inscription: SHUR-TITE. The stem on the obverse features a decal logo, in gold, red and black, of a dog above a diamond device. Inscription within and below device: D & M/.../SPORTING GOODS/MADE IN/U.S.A. Logo also features on red butt cover, impressed in gold. Inscription along right side of stem: MADE BY THE DRAPER-MAYNARD COMPANY/PLYMOUTH, N.H. Materials: Wood, Glue, Lacquer, Metal, Ink, Gut, String, Leather, Clothtennis

Many families at this time obtained and framed these military service certificates. This was part of the empire spirit of 1914. The prose at the top of the certificate is a quote from Act 5 scene 7 of William Shakespeare's "King John".Black and white certificate commemorating the war service of former WHS student Lt. Steel. A number of symbolic images including two men or horseback, a queen, a broken cart, a portrait surrounded by flags and lions and three rifles surround an photograph of Lt. Steel. Bordering the photograph is a modified Australian Government symbol, a laurel wreath, the Australian and British flags and two crossed rifles. Above the Portrait is a FOR KING AND EMPIRE banner and a quote from 'King John', and below is Lt. Steel's details.FOR KING & EMPIRE COME THE THREE FATHERS OF THE WORLD IN ARMS AND WE SHALL SHOCK THEM. NAUGHT SHALL MAKE US RUE IF AUSTRALIA TO ITSELF DO REST BUT TRUE NAME Liet' A. V. Steel REGIMENT 1st Battal'n COMPANY '10' RECORD OF SERVICE 1914 - 1919

Set of nine Engineering standards that were acquired by ESCo during the 1920's. 2261.1 - British Engineering Standards Assoc. No. 101 - 1921, titled "British Standard Specification for Tramway Tyres" dated July 1921. 12pp + printed cover and a folded tip in sheet printed as plate 1, date stamped ESCo 14 Sep. 1923 - 216H x 141W, with "Tait Book Co. 90 William St. Melbourne" stamp on front cover. Light blue grey cover, with off white paper inside. Saddle stapled, rounded corners. Printed by Waterlow & Sons Limited, 49 Parliament Street Westminster SW1. See image 2261i1 for front cover. Publisher - Crosby Lockwood and Son London UK. - see images btm2261i1 and i2 for scans of the document. 2261.2 - British Engineering Standards Assoc. No. 2 - 1922, titled "British Standard Specification and Sections for Tramway Rails and Fishplates" dated March 1922. 56pp including cover, actual pages 35 - 50 are fold out sheets for plates 1 to 8 with rail sections detailed, date stamped ESCo 8 Jun 1926 - 216H x 142W, with "Tait Book Co. 90 William St. Melbourne" stamp on front cover. Light blue grey cover, with off white paper inside. Saddle stapled, rounded corners. Printed by Waterlow & Sons Limited, 49 Parliament Street Westminster SW1. Publisher - Crosby Lockwood and Son London UK. See image btm2261i3.pdf and i4.pdf 2261.3 -Australian Commonwealth Engineering Standards Association, Standard No. E 1a - 1926T - "Tentative Australian Standard Specifications for Railway Permanent Way Material", dated May 1926. 32pp plus cover, date stamped by ESCo 14 June 1926 - 229H x 157W saddle stapled. Grey cover with off white paper inside. Printed by The Australasian Medical Publishing Company Limited. See image 2261i2 for front cover. Publisher - The Association Sydney, Australia. See images i6 and i7 for a pdf scan of this document. 2261.4 - British Engineering Standards Assoc. No. 2 - 1927, proof issue, titled "British Standard Specification and sections for Tramway Rails and Fishplates" dated 1927. 56pp including cover, actual pages 35 - 50 are fold out sheets for plates 1 to 8, date stamped ESCo 16 Jul 1927 - 216H x 142W. Off white paper covers and text. Saddle stapled, rounded corners. Has "Waterlow" name on front cover bottom right hand corner. 2261.5 - Australian Commonwealth Engineering Standards Association, Standard No. C. 30 -1926T - "Tentative Australian Standard Specification for Drum Controllers and Resistances for use therewith for electric motors (DC and AC slip ring, excluding controllers for traction purposes", dated December 1926. 28pp plus cover, date stamped by ESCo 29 Jun 1927 - 227H x 152W. Grey cover with off white paper inside, saddle stapled. Printed by The Australasian Medical Publishing Company Limited. Publisher - The Association Sydney, Australia. 2261.6 - Australian Commonwealth Engineering Standards Association, Standard No. C 33 - 1926T - "Tentative Australian Standard Specifications for Drum Starters for electric motors", dated December 1926. 28pp plus cover, date stamped by ESCo 29 June 1927 - 227H x 153W. Grey cover with off white paper inside, saddle stapled. Printed by The Australasian Medical Publishing Company Limited. Publisher - The Association Sydney, Australia. 2261.7 - Australian Commonwealth Engineering Standards Association, Standard No. E 13 to 15 1927 T - "Tentative Australian Standard Specifications for Railway Rolling Stock Material, locomotive tyres, carriage wagon and tender tyres, weldless steel angle rings", dated August 1927. 32pp plus cover, date stamped by ESCo 15 Sep 1927 - 228H x 153W. Grey cover with off white paper inside, saddle stapled. Printed by The Australasian Medical Publishing Company Limited. Publisher - The Association Sydney, Australia. 2261.8 - Australian Commonwealth Engineering Standards Association, Standard No. E 22 to 29 1928 - "Australian Standard Specifications for Railway Permanent Way Material", dated January 1928. 64pp plus cover, date stamped by ESCo, but not readable - 228H x 153W. Light purple cover with off white paper inside, saddle stapled. Printed by The Australasian Medical Publishing Company Limited. Publisher - The Association Sydney, Australia. 2261.9 - British Engineering Standards Assoc. No. 101 - 1929, titled "British Standard Specification for Tramway Tyres" dated February 1929. 16pp +cover, pages 13 and 14 are foldout plate 1, held together with sewn thread, - 218H x 142W, with "J. Ewins & Sons, Booksellers and Stationers Ballarat" label on front cover. Light blue grey cover, with off white paper inside. Printed by Waterlow & Sons Limited, 49 Parliament Street Westminster SW1. Publisher - Crosby Lockwood and Son London UK. Yields information about British Tramway Standards which were used on Australian and New Zealand Tramways.Set of nine printed books, centre stapled. trams, tramways, standards, tramway equipment, tyres, permanent way, track materials, electric motors, esco

Set of three manufacturer's serial plates from GE 247-A motors used in tramcars. Manufactured in Australia under licence from General Electric of the USA. Known as "railway motors" in the USA. Used extensively in Australian tramway systems. The company changed its name a number of times. 1 - Associated General Electric Industries - Serial Number A1307 2 - Australian General Electric Limited - A2349 3 - Australian General Electric Pty Ltd - A10253 - has the GE logo.Yields information about the Australian Company who made tramway motors in SydneySet of three metal (brass or steel) manufacturers plates for GE 247-A motorsge 247 motors, tramways, trams, motors, general electric, australian made

Used in the late 19th century.A forged steel narrow headed mortising axe with a long wooden handle. It was used in the construction of post and rail fences where it could be used to chip out small pieces in the wood. It has Rob.Sorby Sheffield and Steel Pod stamped on the head with a kangaroo design. The company have been manufacturing 'edge tools' for more than 200 years. They adopted the kangaroo brand in the early 1800's when the new colony of Australia was a big market for their tools. It was used in the late 19th century.Rob.Sorby Sheffield. Steel Pod with a kangaroo design is stamped on the head.axes, cutting tools, hand axes, froes, woodworking tools, cleaving tools

This artefact originates from a petroleum company which operated in Victoria from 1933 until 1945. The Alba Petroleum Company of Australia Pty. Ltd. was established by P. J. Adams and A.G. Wales. They had distribution facilities in the industrial estate of Newport in Victoria and also marketed to South Australia and Tasmania. Their advertising during World War 11 emphasised the need to keep petrol profits in Australia. They claimed to have the largest independent bulk storage unit in Australia. They pioneered the use of tar alcohol which was blended with "standard motor spirit to produce a super fuel. They were marketers of ALBA Super, the Aviation Quality Spirit containing Australian produced alcohol, ALBA motor spirit, ALBA power kerosene and ALBALITE lighting kerosene. In 1945 after the war ended, ALBA was incorporated with the Australian Motorists Petrol Company, which in turn, became AMPOL Petroleum Ltd in 1949.This artefact is representative of an Australian innovative company and a product which was widely used on a local, state and national level for industrial and domestic applications.A cylindrical steel/metal can for petrol storage and transfer. It has the brand name of the company ALBA embossed into the lid.On lid: " ALBA"alba petroleum company, ampol, petroleum companies australia

Hair and beard clipping was frequently carried out at home prior to WW11 and often much later in rural areas. Manual hair clippers were readily available for purchase. Brown's Clippers were a popular choice for many Australian men. This company was based in BIrmingham, England and operated from 1939 until the end of the 1950s. This item has significance as a common item for men both domestically and commercially in the middle decades of the 20th century.A set of manual hair clippers made of chromed steel. An adjustable screw allowed blades to be interchanged.BROWN'S CLIPPER CO (1939) LTD / BIRMINGHAM.ENGLANDhair clippers, home barbers, brown's clipper co. ltd

Hecla produced a wide range of appliances for domestic use, beginning with heaters and later branching out to a wider range of kitchen appliances Hecla was established by Clarence William Marriott, a young Melbourne metal worker. He began manufacturing Australia's first carbon filament electric radiators in 1899. He originally worked for his father James Marriott who commenced business in Melbourne as an art metal worker in 1872 and was, in 1907, appointed as the official art metal worker to the Victorian Government producing items including the ornate iron gates and gas lamp standards outside Melbourne's Parliament House. With the invention of nickel chromium wire after 1900, C.W. Marriott began making more efficient heating elements using this new material in 1916. After being influenced by the eruption of Mount Hekla in Iceland, on 19 December 1918, Clarence registered the brand name "HECLA" with an erupting volcano as its logo. The company Hecla Electrics Pty Ltd was officially registered in 1922. In 1928 the company adopted the advertising slogan, 'By Hecla, it's Good'. The Hecla range rapidly expanded to include electric heaters and radiators, electric foot warmers, electric kettles, ceramic & metal electric jugs, immersion hot water elements, electric fans, electric coffee percolators, electric toasters, electric grillers and stoves, electric irons and electric frypans, clocks and curling wands. Electric blankets were introduced shortly after WWII.In 1930, a controlling interest in Hecla Electrics Pty Ltd was acquired by General Electric Corporation. Clarence William Marriott died in June 1967 in Melbourne, Victoria.This item is representative of a common domestic appliance used throughout Australia. It was manufactured by a pioneering Australian company.A small chrome steel toaster manufactured by Hecla Australia. It has a door on either side which flips down to insert or remove a slice of bread on each side, Each door has two black Bakelite knobs. The electric element is placed down the centre of the cavity. A detachable electric cord is included.240 Volts, 600 Watts. Cat. No. T4 Submitted to Electrical Approval Board Ref Application A1/AD01 SECV 240 Volt 600 Watt MANFED. IN AUSTRALIA SOLID BRASSelectrical appliances, hecla corporation australia, clarence william marriott, domestic appliances

Part of the 'Mann' collection in the Wodonga Historical Society, used for accounting in the J. Mann & Sons General Store in High Street, Wodonga in 1934-35. J. Mann and Sons was first established as a farm produce store in 1921. The range of products was extended in the 1930s and included groceries and hardware, as well as the first petrol bowser in Wodonga outside the store. After WWII, the premises were extended and the range of products continued to increase. In the 1960s the Mann Family opened a new supermarket in Wodonga, in addition to the hardware business, providing steel, plumbing and industrial supplies, and they employed over 100 people at one stage. With changes in the retail industry, the Mann Family sold the main hardware business to Bunnings and the produce business to the Kelly brothers in 2006. Local significance due to its use in the J. Mann & Sons General Store in High St, Wodonga and association with the prominent Mann family. National significance as kalamazoos were manufactured by an Australian company and used in the 1930s for accounting purposes by local businesses.Visible card book or kalamazoo used by the accounts department of J. Mann & Sons General Store, High Street, Wodonga, in 1934-35 for customers with surnames from K to P.Details for each customer provided on individual cards. "KALAMAZOO - ACME / Visible Card Equipment / THE "RAPID SIGHT" METHOD / Kalamazoo (AUST.) LTD. / SYDNEY - MELBOURNE - BRISBANE - ADELAIDE"mann, accounting, financial record, high street wodonga, wodonga, commerce, business, kalamazoo, general store, j. mann & sons

This medal is the Liverpool Shipwreck and Humane Society’s “Bramley-Moore medal for saving life at sea 1872”. The Society was formed in 1839. In 1872 Mr John Bramley-Moore donated £500 on condition that the medal have the specific inscription above on its reverse. The Bramley Morre medal was first awarded in 1874 and records show that since that time only one gold medal has been awarded, twenty-two silver medals and seventeen bronze medals, the last being in 1945. This Bromley-Moore medal was awarded to Peter Carmody for his bravery in saving lives on the Newfield shipwreck. The Newfield was a three-masted iron and steel barque, built in Dundee, Scotland, in 1889 by Alexander Stephen and Sons. It was owned by the Newfield Ship Company in 1890 and later that year It was registered in Liverpool to owners Brownells and Co. The Newfield left Sharpness, Scotland, on 28th May 1892 with a crew of 25 under the command of Captain George Scott and on 1st June left Liverpool. She was bound for Brisbane, Australia, with a cargo of 1850 tons of fine rock salt, the main export product of Sharpness. At about 9pm on 28th August 1892, in heavy weather, Captain Scott sighted, between heavy squalls, the Cape Otway light on the mainland of Victoria but, due to a navigational error (the ship’s chronometers were wrong), he assumed it to be the Cape Wickham light on King Island, some 40 miles south. He altered his course to the north, expecting to enter Bass Strait. The ship was now heading straight for the south west Victorian coast. At about 1:30am the Newfield ran aground on a reef about 100 yards from shore and one mile east of Curdie’s Inlet, Peterborough. The ship struck heavily three times before grounding on an inner shoal with 6 feet of water in the holds. Rough sea made the job of launching lifeboats very difficult. The first two lifeboats launched by the crew were smashed against the side of the ship and some men were crushed or swept away. The third lifeboat brought eight men to shore. It capsized when the crew tried to return it to the ship for further rescue The rescue was a difficult operation. The Port Campbell Rocket Crew arrived and fired four rocket lines, none of which connected with the ship. Peter Carmody, a local man, volunteered to swim about one mile off shore to the ship with a line to guide the fourth and final lifeboat safely to shore. He was assisted by James McKenzie and Gerard Irvine. Seventeen men survived the shipwreck but the captain and eight of his crew perished. The Newfield remained upright on the reef with sails set for a considerable time as the wind slowly ripped the canvas to shreds and the sea battered the hull to pieces. The Marine Board inquiry found the wreck was caused by a "one man style of navigation" and that the Captain had not heeded the advice of his crew. According to Jack Loney ‘… when the drama was over . . the Newfield was deserted except for the Captain’s dog and two pigs.’ Peter Carmody was awarded the Bramley-Moore medal by the Liverpool Shipwreck and Humane Society for Saving Life at Ssea, which he received by mail on January 21st 1893. The medal and a letter of congratulations were donated to Flagstaff Hill Maritime Museum by Peter Carmody’s grand-daughter Norma Bracken and her son Stuart Bracken on 25th May 2006. The Medal and Letter of Congratulations join other items in the Newfield collection.The Carmody Medal recognises the bravery of Peter Carmody in risking his life to rescue crew members of the Barque Newfield when it was wrecked near Curdies Inlet in August 1892. The ‘Bramley-Moore medal for saving life at sea, 1872’ was presented by the Liverpool Shipwreck and Humane Society. The medal and accompanying letter have local and international historic significance as they demonstrate both the difficulties associated with navigation and the dangers of shipping along the South West Coast of Victoria in the 19th century and the medal’s association with the Liverpool Shipwreck and Humane Society and John Bramley-Moore, who provided £500 to found the Bramley-Moore medal. The medal is socially significant. It emphasises the importance of Peter Carmody in rescuing victims of shipwrecks with little thought for his own safety. The medal reminds us of the importance of local people to Victoria’s maritime history. The Carmody Medal and Humane Society letter were in the Carmody family until they were presented to Flagstaff Hill Maritime Village, by the grand-daughter and great-grandson of Peter Carmody, on the 25th May 2006. The medal is significant for its complete provenance recorded in the donation documentation. The medal is in very good condition and relatively rare with only 22 silver medals awarded between 1874 and 1945. The Carmody Medal and letter add a human element to the story of the shipwrecks. They give life and significance to the Newfield, its victims and its artefacts. Bramley-Moore medal from the Liverpool Shipwreck and Humane Society, awarded to Peter Carmody. The round,silver medal is attached to a looped blue ribbon by a decorative, swivelling silver connector. The top of the ribbon has a silver pin bar threaded through it. The obverse of the medal has a design of a man kneeling on a floating part of a wreck. He is rescuing a child from the sea. There is a manned boat in the distance rescuing someone from the sea. In the far background there is a sailing ship. The top third of the medal has an inscription around it. The reverse shows a long-legged hen cormorant with extended wings holding an olive branch in its beak. The bird is surrounded by a wreath of oak leaves made from two branches. There is an inscription between the design and the rim that goes all the way around the circumference. There is a name engraved around the edge of the medal. The medal in embedded in a purple velvet panel that rests inside a brown, leather-covered case. The lid of the case has a gold embossed emblem in the cemtre. Both the lid and base have a rectangular gold border. The lid is attached to the base with two brass hinges. The base has a brass push-button catch. The box is lined with padded cream silk. The lining inside the lid has a gold emblem in the centre.The obverse has the words "LORD, SAVE US, WE PERISH". The reverse has the words "BRAMLEY-MOORE MEDAL FOR SAVING LIFE AT SEA" and "1872". Around the edge of the medal are the words "PETER CARMODY, FOR HAVING BEEN MAINLY INSTRUMENTAL IN RESCUING THE CREW OF THE BARQUE NEWFIELD, AUG 29 1892" The pin bar has the words “LIVERPOOL SHIPWRECK & HUMANE SOCIETY” written across it. The gold embossed emblem on the lid of the box has the words in the centre "SHIPWRECK AND …. …. ….FOUNDED 1839" The gold emblem on the cream silk lining has the words “BY APPOINTMENT ELKINGTON & CO” printed on it.medal, shipwrecked coast, flagstaff hill, flagstaff hill maritime museum, maritime museum, flagstaff hill maritime village, shipwreck coast, warrnambool, peter, peter carmody, carmody, bramley moore, newfield, liverpool shipwreck and humane society, 1892, 28 august 1892, august 1892, port campbell, bravery, shipwreck, rescue, nineteenth century, ship, curdie s river, victorian shipwrecks, barque, stuart bracken, norma bracken, gerard irvine, james mckenzie

Timetable - 36 pages, printed on off-white paper, cover printed on pink paper, centre stapled titled "Victorian Tramways Guide" for October 1917. Details the timetables for the Tramway Board, Northcote Council, PMTT, NMETL, HTT, MBCTT and the VR Brighton line. Gives details of fares, routes, signs, first and last cars. Middle page - has a map and details of a Round trip and shows other lines and change points. Foldout map included on the inside rear cover, showing tramways, railways and rivers. Has many advertisements for the re-election of Sir Frank Madden (he was not re-elected - see http://www.parliament.vic.gov.au/re-member/details/569-madden-frank - accessed 30-12-2016). Polling day 15/11/1917. Has adverts for: Commercial Union Steel Castings Proprietary Limited Myer's Country of Bourke Permanent Building and Investment Society Prohibition - Canada, USA Royal Insurance Company Australian Ladies Commercial College Incley Frederick Collis Tramways Advertising Co. Stott's Business College Chambers and Seymour W. M Richards Huttons Ham Sterling Preparationstrams, tramways, timetables, melbourne, nmetl, vr, cable trams, htt, pmtt, map, advertising

The American Foundation for the Blind developed this new model in their experimental shop in 1932 and contracted with the typewriter manufacturer to produce the machines and continued production until 1947. It's sleek silver look was a change of look from the previously manufactured Hall Braille Writer, and improvements included a carriage return, the ability to add spaces between lines and a back space key. It was found in the Braille and Talking Book Library in South Yarra, Victoria, Australia and was used by either staff or volunteers at Vision Australia Library.Stainless steel braille writer in the shape of a typewriter. The braille writer consists of a heavy moulded machine with 6 black plastic keys.On front of writer: "American Foundation for the Blind Inc. New York." "Manufactured for the Foundation by L.C. Smith & Corona Typewriters, Inc." On back: "Licenced by Underwood Elliot Fisher company/ Serial no. 5-2422.braille equipment, assistive devices