Showing 1193 items
matching pipe
-
Tatura Irrigation & Wartime Camps Museum
Lathe (Model)
"This is a rough model of the woodturning lathe Kurt Beilharz built from scrap as a 17 year old in Camp 3, Tatura. The drive wheel was a hollow redgum block from the firewood supply. The shaft was a 1/2" water pipe, the bearings of the spindle were 3/4" water pipe with tooth paste tubes melted into and honed out for the spindle. They had holes for oiling. The drive belt came from my Mother's sewing machine. I used screws in the model, but in reality bolts were used, which were bought as well as the framing timber"Wooden model of a lathe made and used at Camp 3. Triangular upright frame with a hollow drive wheel, driven by a piece of wire with a handle on one end. Drive belt is a piece of fine cord.lathe, model, beilharz, k, camp 3, tatura, ww2 camp 3, handcrafts, models -
Greensborough Historical Society
Photograph - Digital Image, Aqueduct Greensborough, 1960c
The Pipe Bridge at Greensborough is a significant and highly visible part of the system. It was constructed to carry the wrought iron aqueduct pipes over the Plenty River. The use of wrought iron meant the pipes were 75% lighter than cast iron, with the bridge construction reflecting this innovation. Photograph of the Maroondah Aqueduct pipe bridge at Greensborough. The Pipe Bridge is 210 feet long, divided into 4 spans. The main girders are light lattice 11 feet deep and 11 ft 4 inches apart. The bridge carried two wrought iron tubular mains, 53 inches in diameter, supported at intervals by cross girders and chairs, placed between the main girders. The bridge is carried on braced cast-iron columns, 18 inches in diameter, set on concrete foundations, with a clear headway of 20 feet above the Plenty River. The eastern side of the bridge is reinforced with a bluestone abutment at the river bank.Digital copy of colour photograph.maroondah aqueduct, aqueduct pipe bridge greensborough -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, Mid-to-late 1800s
This olive green bottle was handmade by a glassblower and is the typical shape of a ‘gallon’ type liquor bottle, which has the capacity of one-sixth of an imperial gallon, about 750ml. It was made around the mid-to-late 1800s. The bottle was recovered from an unnamed shipwreck in the coastal water of Victoria. It is part of the John Chance Collection. The elongated bubbles in the glass are likely from the glass being blown into a mould. Glassblowers made bottles like this one by blowing into a long metal pipe or reed with a blob of molten glass at the end of it. The shape of the glass would be blown out to fit into the shape of the mould. Once it set, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck and another tool to finish the base. The bottle would be cracked off the end of the glassblower’s pipe and a blob of molten glass would be added to the top to form the mouth and lip of the bottle. The seal was usually a cork, often held in place with tape. Although the bottle is not linked to a particular shipwreck, it is recognised as being historically significant as an example of bottles imported for use in Colonial Victoria in the mid-to-late 1800s. The bottle is also significant as it was recovered by John Chance, a diver in Victoria’s coastal water in the late 1960s to early 1970s. Items that come from several wrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value. Bottle, dark olive green glass, tall thin Gallon type. Mouth is applied roughly, lip is straight and narrow. Body has no visible seams; tapers gently inwards to base. Concave base is deep and has a pontil mark. No inscriptions. Handmade bottle has elongated air bubbles and imperfections in glass.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, gallon bottle, handmade, mouth blown, pontil mark, blown bottle, liquor bottle, 19th century bottle, collectable, olive glass, green glass, mould, 1800s bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, circa 1870-1910
This brown glass bottle has been handmade from about the 1870s-1910s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. A 'ponty' (pontil) tool would been used to complete the shape, pushing up the base. A tool would have been used to cut off the bottle from the blowpipe and apply and form the ring band on the neck. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, late 19th to early 20th century beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, brown glass, tall and slim, cork-top style. Tooled finish on mouth with applied ring, shoulder seam, body tapers inwards towards base. Concave base has pontil mark. Sediment inside bottle. Glass has shiny surface and diagonal rings from shoulder to mouth, then is less shiny and has an slightly undulating surface from shoulder to base. The surface is markedly raised where base and shoulder meet. Glass has many scratches.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, brown glass, ale bottle, beverage bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This olive green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. A 'ponty' tool would have been used to form the push-up base. The mouth of the bottle was cut off from the blowpipe and a piece of soft glass would be added to the mouth to then form the double collar. Bottles like this would usually be sealed with a cork, perhaps with tape or and anchored wired over it to keep it in place. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, olive green glass. Applied double lip; deep upper, ring lower. Slightly bulbous neck with crease lines n glass. Shoulder seam. Body tapers inwards towards base. Concave base, inward pontil mark, uneven base. Sediment inside bottle.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, beverage bottle, green glass, olive glass, double collar -
Horsham RSL Sub Branch
Sword Bayonet
1855 British Lancaser No 10 pattern Sword Bayonet. Long straight blade swelling out beyond the back edge towards the point witha single edge and a pipe back. Brass hilt with chequered compressed leather hand gripsSerial No. 945 Stamps on blade. -
Bendigo Historical Society Inc.
Book - THE SOUND OF THE CITY, 2001
The Sound of The City, a tribute to the men and women who have woven the magic of fifty years of piping and drumming in Golden City Pipe Band Bendigo, published by Mulqueen printers Golden Square, 152 pages with illustrations and photographs, some colour.Ann C Scottbendigo, clubs, pipe bands, signed by author. -
Coal Creek Community Park & Museum
Miners lamp
8485.1 - Painted black truncated cone, the base being wider than the top with the narrow pipe extending from the top. The handle is a curve of wide metal strip, also with a tube extending from the top. The top and bottom are slightly domed. -
Tatura Irrigation & Wartime Camps Museum
Photograph, Goulburn Weir, 1890
Taken by photographer for State Rivers and Water Supply Commission.Medium sized black and white photograph. Galvanised pumping shed, tall chimney, open wooden door, centre photo - pipe running on wooden structure from water (foreground) into shed. man with arm on horse's neck to the left of shedgoulburn weir, victorian state rivers and supply commission -
Rutherglen Historical Society
Postcard - Image, Greetings from Rutherglen, 1910 to 1912
Black and white postcard with two oval photographs with "Greetings from Rutherglen" on a banner between them. The top photograph is a view of a riverbank with a man seated on the bank fishing and smoking a pipe. The bottom one is a picture of the Post Office in Main Street.At bottom of top photograph: "The Murray River." At bottom of bottom photograph: "Post Office." Message on back of card: "To Mr Barber with every Good Wish for a merry xmas and the Happiest of New Years. From your old friends Sam & Nellie Williams. 23/12/13."murray river, rutherglen post office, christmas greetings, sam williams, nellie williams -
Surrey Hills Historical Society Collection
Photograph, Mr Natale Cerini in the Surrey Gardens, c1936, c 1936
Information from the donor, Natale Cerini's daughter: He was a retired accountant who commenced the Surrey Hills Observer, one of the early free local papers, in about 1933 at the request of the Surrey Hills Progress Association of which he was a member. He regarded his solo effort in creating, editing and publishing the paper as a community service for which he received no remuneration. The Observer was self-funding through its advertisements which Mr Cerini personally collected throughout the area. The Observer was issued fort-nightly and printed by the Johnson family at the Triumph Press in Sunbury Crescent until about 1946 when Mr Cerini relinquished it to one of the newly-established post-war local papers. Photo thought to have been taken in 1936 when Mr Natale would have been 69, as he retired in 1932 at 65 years of age. Electoral rolls give the following addresses: 1919: 293 Dandenong Road (accountant) and 1919 Boondara, Croydon (accountant); both with Ethel May also listed. 1924: 167 Union Road, Surrey Hills (accountant) 1931 and 1943: 215 Union Road, Surrey Hills (accountant). Marriage: Natale Benjamin Cerini; Spouse Name: May Ethel Swan; Marriage Place: Victoria; Registration Place: Victoria;Registration Year: 1918; Registration number: 5787. Ethel May Cerini: Death Place: S Hills, Victoria; Age: 69; Father's Name: Ernest Harrison; Mother's Name: Frances Ann Clark; Registration Year: 1951; Registration Place: Victoria; Registration number: 10736; Estimated Birth Year: abt 1882. Natale Benjamin Cerini: Death Place: Glen, Victoria; Age: 89; Father's Name: Joseph Natale; Mother's Name: Sarah Cooke; Registration Year: 1954; Registration Place: Victoria; Registration number: 10612; Estimated Birth Year: abt 1865.Black and white photo of a hatted gentleman with a walking cane and a pipe and wearing glasses. He has a rosette in his suit buttonhole and a ribbon on his lapel. The background is blurred but is reliably identified as the Surrey Gardens during Empire Day celebrations. SH368 on rear in pencilempire day, festivals and celebrations, surrey gardens, newspapers, surrey hills progress association, surrey hills observer, triumph press, natale cerini -
J. Ward Museum Complex
Functional object - Cutter - Tobacco, 1900 - 1950
Tobacco cutters were important tools for pipe smokers until self-made or manufactured cigarettes began to dominate the tobacco sales market from the 1920s. This item is a link to a previously common means of consuming tobacco.Tobacco cutters were used at both J Ward and the Aradale complex in Ararat. They were used to cut tobacco, which was then apportioned out to patients for their consumption.Metal tobacco cutter (guillotine style), mounted on wooden base, with wooden striker plate.A. McMILLAN inscribed on striker plate.tobacco, cutter -
Bendigo Historical Society Inc.
Functional object - Tobacco Cutter
Tobacco cutters were used to cut solid blocks of tobacco ( plugs) into finer pieces for smoking before the advent of tailormade cigarettes and particularly for pipe smokers. Wholesalers often included a cutter with bulk tobacco orders.Metal tobacco cutter with a detachable blade on a wooden base.tobacco cutter, smoking instrument -
Warrnambool and District Historical Society Inc.
Badge, Warrnambool & District Pipes & Drums, Late 20th century
This badge comes from the Warrnambool and District Pipes and Drums and is presumably attached to an item of clothing. The Warrnambool Pipe Band was formed in 1906, originally to popularise Scottish music and later to foster a taste for bagpipe music. Simon Fraser, the first Pipe Major, held the position from 1906 to 1910. The band appears to have gone into recess during the latter years of World War One and was apparently re-formed in 1935. Again in World War Two the band was in recess The band has had several changes of title but is today known as the Warrnambool and District Pipes and Drums. The badge is of interest as an example of one of the badges belonging to Warrnambool & District Pipes and Drums, an important and long-serving band in Warrnambool. This is a multi-coloured cloth badge, circular in shape. The outside edge is machine stitched in yellow and there is a blue band with the wording in yellow ‘Warrnambool & District Pipes and Drums’. In the inner circle there is an image, in colours of white, red, yellow, black and dark blue, of two drums, a staff and bagpipes stitched on a blue background. The back has a paper label with the details of the maker. ‘Warrnambool & District Pipes and Drums’ ‘Action Badges Pty Ltd, 34 Tooronga Terrace, Beverly Hills, N.S.W., 2209, Telephone (023) 502 4077’ warrnambool & district pipes and drums, badge -
Flagstaff Hill Maritime Museum and Village
Gramophone cylinders, National Phonograph Co, The Highland Laddie
Gramophone cylinders, black, 6 grooves on interior stored in cardboard round container with detachable lid. Edison Gold Moulded Record, made and sold by National Phonograph Co. at Orange N.J. U.S.A. 13737 The Highland Laddie - Pipe Major Forsythe. flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, gramophone cylinder, edison gold moulded record, national phonograph co, the highland laddie, pipe major forsythe. -
Bendigo Historical Society Inc.
Leisure object - GERTRUDE PERRY COLLECTION: PIPE CLEANER DOLL, 'THE ARCADIANS', 1956 PRODUCTION
Pipe cleaner doll mounted on buff cardboard. Doll is dressed in green material, holding red bags. On top RH corner ' To remind you of Eileen Cavanagh, The Arcadians, April, 1956'. THIS ITEM COULD NOT BE LOCATED ON THIS DAY 29/07/21.person, individual, gertrude perry -
Eltham District Historical Society Inc
Negative - Photograph, J.A. McDonald, Heidelberg-Kinglake Road, Mar. 1960
Cherry Tree Road Job 56F443 Contractors Wolf and Wood Culverts in place, 3 rows 73” diameter 45-degree skew Looking towards Panton Hill – before trimming ends of pipe March 1960Record of various Shire of Eltham infrastructure works undertaken during the period of 1952-1962 involving bridge and road reconstruction projects, sometimes with Eltham Shire Council Project Reference numbers quoted. It was during this period that a number of significant improvements were made to roads and new bridges constructed within the shire that remain in place as of present day (2022). In many situations, the photos provide a tangible visible record of infrastructure that existed throughout the early days of the Shire. The album was put together by or under the direction of the Shire Engineer, J.A. McDonald.infrastructure, 1960-03, bridge construction, cherry tree road, heidelberg-kinglake road, road construction, shire of eltham -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This brown glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe. A piece of soft glass would be added to the mouth, then the double collar would be formed. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, brown glass, rough surface, uneven colour. Crude, applied mouth with double collar; wide straight upper, ring lower. Slightly bulbous neck. Shoulder seam. Body tapers inward towards base and has smooth ripples. Shallow base with wide heel. No obvious pontil mark. Sediment inside bottle. Glass is scratched in places. flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, brown glass, ale bottle, beverage bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This brown glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then formed into the double collar lip. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, brown glass, wide body, cork-top style. Applied double collar, straight upper, flared lower. Short bulbous neck, wide shoulder with seam, body tapers inward to base. Shallow base with wide uneven heel. Bubbles, disculouration and creases in glass. Sediment in bottle. Inscription in base.Embossed in base [indecipherable]flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, brown glass -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then formed into the double collar lip. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, green glass, cork-top style. Applied mouth, lip has double collar; wide upper and flared lower. Vertical bubble in bulbous neck. Long diagonal discolouration along neck. Body has ripples around it and no seams. Heel is thick, base is shallow, has bubbles and is very uneven on a flat surface.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, green glass bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then formed into the double collar lip. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, dark green glass, matt surface, cork-top style. Applied double lip: straight upper and flared lower. Slight bulbous neck, shoulder seam, body tapers inwards towards base and has a rippled surface. The uneven base has a thick heel and is concave with small pontil mark.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, green glass bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then formed into the double collar lip. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, olive glass, matt surface with opalescence in places, cork-top style. Applied double lip; straight upper, flared lower. Slightly bulbous neck, high shoulder seam, body tapers inwards towards base and has rippled surface in areas. Uneven heel thickness, concave base. Bubbles, rippled surface and circular blow marks in glass. Label remnants on the surface. Internal sediment top to bottom along one side.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, green glass bottle -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This olive green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base may have been part of the dip mould, otherwise, a 'ponty' tool would have been used to flatten the base. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then formed into the flared collar. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, olive glass, cork-top style. Applied flared lip, slightly bulbous neck with horizontal lines in glass. Shoulder has seam, body tapers inwards towards base. Heel is thick, with concave base, wide inverted pontil, uneven base. Glass has some bubbles, blow lines and imperfections. Sediment inside bottle along one side. Surface of glass is scratched.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, bottle, dip mould, soda bottle, ale bottle, beverage bottle, olive green glass -
Flagstaff Hill Maritime Museum and Village
Container - Bottle, c. 1840s - 1870s
This olive green glass bottle has been handmade from about the 1840s to 1870s. The bottle, possibly used to store ale or soda or mineral water, was found in the coastal waters of Victoria. It is part of the John Chance Collection. Glassblowers made bottles like this one by blowing air through a long pipe into the molten glass blob at the end of the pipe. The glass was blown out to fit into the shape of the cylindrical dip mould. Once it hardened, the glass was removed from the mould and the glassblower would continue using the pipe to create the neck while carefully using a tool to hold the base. The base was made using a 'ponty' tool to push it up, giving a concave finish with a central 'ponty' mark. A tool would have been used to cut off the bottle from the blowpipe and a piece of soft glass would be added to the mouth to then shape the band collar. Bottles like this would usually be sealed with a cork, which may have been held in place with wax or wire and tape. Although this bottle is not linked to a particular shipwreck, it is recognised as a historically significant example of handmade, 1840s to 1870s beverage bottles imported for use in Colonial Victoria. The bottle is also significant for its association with John Chance, a diver in Victoria’s coastal waters in the late 1960s to early 1970s. Items that come from several shipwrecks have since been donated to the Flagstaff Hill Maritime Village’s museum collection by his family, illustrating this item’s level of historical value.Bottle, olive glass, cork top style. Roughly applied tooled lip with band, smooth body outline tapering intwards towards base. Concave base, small pontil mark, uneven base. Glass has rippled, circular blow lines. Sedimint inside bottle.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, shipwreck artefact, john chance, glass bottle, antique bottle, handmade, mouth blown, blown bottle, collectable, dip mould, soda bottle, beverage bottle, olive green glass -
Stawell Historical Society Inc
Photograph, Fluming Water Supply in the Grampians 1991 -- 9 Photos -- Coloured
Coloured photos of Fluming Water Supply in the Grampians. a. Grampians Exit of tunnel through Mt William Range built 1874. b. Halls Gap Fyan's Creek with buried pipe from new diversion Weir Nov 24/91 (Fume Main). c. Halls Gap New Diversion Weir (Keith Phillips) Nov 24/1991. d. Halls Gap Old pipe to open flume adapter Nov 24/1991. e. Halls Gap Old metal open flume Nov24/91. f. Halls Gap Old metal flume and man made stone supporting wall. g. Halls Gap Overhanging rocks above old fume line Nov 24/1991. h. Halls Gap Old pipe to open flume adapter Bill Holmes Nov 24/91. i. Grampians Old hut for controlling flow valves etc. at Stawell side of Mount William Range after tunnel exit. Nine colour photographs of various views around a tunnel through a hill site.grampians water supply flume -
Ballarat Tramway Museum
document - Correspondence, Ballarat Tramway Museum (BTM), 31/12/2006 12:00:00 AM
Set of drawings and photocopies of sanding equipment on Ballarat Tramcars, provided to the Launceston tramway Museum for information.Copy of Correspondence with the Launceston Tramway Museum 31/12/2006 concerning sand ejector equipment fitted to Ballarat tramcars. Comprises: Covering letter dated 31/12/2009 Photographs of the Ejector unit with fittings - two views Photograph of the inlet pipe Sketch of the air inlet pipe - prepared by Warren Doubleday Prints of drawings - BA - T7 - 7654 - Ejector for Sand Box, Fabricated type - 21E truck, SEC 1938 - made from scans ex Microfilm BA - T7 - 7647 - Ejector for Sand Box, Brill 21 E Truck - SEC 1938 - cast type.tram, trams, tramcar equipment, sanding equipment, sand ejectors, letters -
Greensborough Historical Society
Photograph - Digital Image, Marilyn Smith, Aqueduct crossing the Plenty River, Greensborough 2019, 02/07/2019
The aqueduct crossing the Plenty River, 2019, overgrown with vegetation. Originally part of the Maroondah Aqueduct pipeline, all that remains is the bridge that once carried the pipe over the Plenty River. This photograph was taken from the Plenty River Trail in Greensborough. 3 colour digital photographsplenty river trail, maroondah pipetrack, maroondah aqueduct, plenty river, graffiti -
Marysville & District Historical Society
Book, Charles Kenneth Thompson, Old Bob's Birds, 1950
A book that is part of a series of Australian Nature Stories by C.K. Thompson.On the front of the dust cover is an illustration of an old man sitting on a bench outside an aviary smoking a pipe and there is a bird sitting on his shoulder. He is talking to two children. On the back of the dust cover is the blurbs of two other novels written by C. K. Thompson.fictionA book that is part of a series of Australian Nature Stories by C.K. Thompson.australia, nature, birds, c.k. thompson, fiction, old bob -
Bendigo Historical Society Inc.
Photograph - CASTLEMAINE GAS COMPANY COLLECTION: PHOTO PEOPLE, 1963
From Left to Right: Wally Thompson ( Standing behind tool cart main layer) - Bert Hill (Foreman) - Ken Cain (Welder) - Jack Hawke (Service Layer) - Operation; preparing length of welded pipe. Early 1963. McIvor Road Hill.person, group, male group of workers -
Bendigo Historical Society Inc.
Textile - GERTRUDE PERRY COLLECTION: DOLLS
Two small dolls. One is in a plastic pocket, attached note: pipe cleaner doll by Madge Welch, The Merry Widow, 1953. Miss G. Perry from Madge Welch to remind you of Sonia. this doll is in a black dress. The other is in a red dress.ephemera, mementoes, gertrude perry collection