Caulking is the use of cork or other substances to seal the seams and joints of the vessel to make them watertight. Caulking lasts for quite some time but eventually dries out and needs to be replaced. A mallet or hammer is often used with a caulking iron to drive it along the seams. The caulking iron’s blade is tapered to be narrower at the tip to make it easier to remove it from the joint. The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings. You can see Laurie’s inscription on the tool called a ‘bevel’. Laurie worked for Ports and Harbours, Melbourne, for over 50 years, beginning in the early 1960s. He and a fellow shipwright inscribed their names on a wheelhouse they built in 1965; the inscription was discovered many decades later during a repair of the plumbing. Many decades later Laurie worked on the Yarra moving barges up and down the river and was fondly given the title ‘Riverboat Man’ His interest in maritime history led him to volunteer with the Maritime Trust of Australia’s project to restore and preserve the historic WWII 1942 Corvette, the minesweeper HMAS Castlemaine, which is a sister ship to the HMAS Warrnambool J202. Laurie Dilks donated two handmade displays of some of his tools in the late 1970s to early-1980s. The varnished timber boards displayed the tools below together with brass plaques. During the upgrade of the Great Circle Gallery Laurie’s tools were transferred to the new display you see there today. He also donated tools to Queenscliffe Maritime Museum and Clunes Museum.The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright at Ports and Harbours in Melbourne in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings.Caulking mallet; a thick wooden handle with a round ‘T’ cross-bar near the end. Metal reinforcing is added around the ends of the head. Both sides of the wooden head are flared outwards towards the end. The head is reinforced where it intersects with the handle and around the ends of the head just above the tips. It once belonged to shipwright Laurie Dinks.flagstaff hill, maritime museum, maritime village, warrnambool, shipwreck coast, great ocean road, shipwright, carpenter, shipbuilding, ship repairs, hand tool, equipment, caulking, ship maintenance, cooper, shipwright’s tools, shipwrights’ tools, tools, maritime trade, caulking mallet, caulking iron, laurie dilks, l dilks, port and harbours melbourne

Caulking is the use of cork or other substances to seal the seams and joints of the vessel to make them watertight. Caulking lasts for quite some time but eventually dries out and needs to be replaced. A mallet or hammer is often used with a caulking iron to drive it along the seams. The caulking iron’s blade is tapered to be narrower at the tip to make it easier to remove it from the joint. The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings. You can see Laurie’s inscription on the tool called a ‘bevel’. Laurie worked for Ports and Harbours, Melbourne, for over 50 years, beginning in the early 1960s. He and a fellow shipwright inscribed their names on a wheelhouse they built in 1965; the inscription was discovered many decades later during a repair of the plumbing. Many decades later Laurie worked on the Yarra moving barges up and down the river and was fondly given the title ‘Riverboat Man’ His interest in maritime history led him to volunteer with the Maritime Trust of Australia’s project to restore and preserve the historic WWII 1942 Corvette, the minesweeper HMAS Castlemaine, which is a sister ship to the HMAS Warrnambool J202. Laurie Dilks donated two handmade displays of some of his tools in the late 1970s to early-1980s. The varnished timber boards displayed the tools below together with brass plaques. During the upgrade of the Great Circle Gallery Laurie’s tools were transferred to the new display you see there today. He also donated tools to Queenscliffe Maritime Museum and Clunes Museum.The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright at Ports and Harbours in Melbourne in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings.Calking iron, a metal tool with a round flat top and head that flares outwards to a wide wedge shape. It once belonged to shipwright Laurie Dinks.flagstaff hill, maritime museum, maritime village, warrnambool, shipwreck coast, great ocean road, shipwright, carpenter, shipbuilding, ship repairs, hand tool, equipment, caulking, ship maintenance, cooper, shipwright’s tools, shipwrights’ tools, tools, maritime trade, caulking iron, laurie dilks, l dilks, port and harbours melbourne

Caulking is the use of cork or other substances to seal the seams and joints of the vessel to make them watertight. Caulking lasts for quite some time but eventually dries out and needs to be replaced. A mallet or hammer is often used with a caulking iron to drive it along the seams. The caulking iron’s blade is tapered to be narrower at the tip to make it easier to remove it from the joint. The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings. You can see Laurie’s inscription on the tool called a ‘bevel’. Laurie worked for Ports and Harbours, Melbourne, for over 50 years, beginning in the early 1960s. He and a fellow shipwright inscribed their names on a wheelhouse they built in 1965; the inscription was discovered many decades later during a repair of the plumbing. Many decades later Laurie worked on the Yarra moving barges up and down the river and was fondly given the title ‘Riverboat Man’ His interest in maritime history led him to volunteer with the Maritime Trust of Australia’s project to restore and preserve the historic WWII 1942 Corvette, the minesweeper HMAS Castlemaine, which is a sister ship to the HMAS Warrnambool J202. Laurie Dilks donated two handmade displays of some of his tools in the late 1970s to early-1980s. The varnished timber boards displayed the tools below together with brass plaques. During the upgrade of the Great Circle Gallery Laurie’s tools were transferred to the new display you see there today. He also donated tools to Queenscliffe Maritime Museum and Clunes Museum.The shipwright’s tools on display in the Great Circle Gallery are connected to the maritime history of Victoria through their past owner, user and donor, Laurie Dilks. Laurie began his career as a shipwright at Ports and Harbours in Melbourne in the mid-1900s, following in the wake of the skilled carpenters who have over many centuries used their craft to build and maintain marine vessels and their fittings.Caulking iron; an iron tool with round flat surface on top, above a narrow, long round handle that flares outwards to form a thick, narrow wedge shape. It once belonged to shipwright Laurie Dinks.flagstaff hill, maritime museum, maritime village, warrnambool, shipwreck coast, great ocean road, shipwright, carpenter, shipbuilding, ship repairs, hand tool, equipment, caulking, ship maintenance, cooper, shipwright’s tools, shipwrights’ tools, tools, maritime trade, caulking iron, laurie dilks, l dilks, port and harbours melbourne

"The Melton Viaduct, opened in 1886, is of State heritage significance as a very large and visually distinctive wrought iron, lattice girder trestle bridge over the Werribee River (now Melton Reservoir). It comprises 18.3 and 9.1 metre spans, in a generally alternate arrangement, of total length 375 metres, and standing 38 metres over the Werribee River. Wrought iron small section iron was used to build tension trussed trestle legs, which supported four lines of rivetted wrought-iron deck-type double lattice trusses. It has bluestone abutments and pier bases of coursed rock-faced bluestone with drafted margins. The larger half-piers, now usually submerged in the Melton Reservoir have sharp tapered cutwaters and curved coping at the tops. While designed to carry two rail tracks it has only ever been used as a single track line. Despite several alterations to its deck structure, it remains an outstanding example of a lighter structural design employing open metal trestle supports and metal truss girders. The direct Melbourne to Ballarat railway link of which the Melton viaduct was the major engineering work contributed significantly to the history and development of Victoria. This new link reflected Ballarat’s diversifying economy as well as the commercial and political influence of the metropolis. Construction of the bridge, and the associated large workers camp, were extensively photographed, documenting an important episode in local history. The railway enabled the development of new industries in the Melton area, notably the timber industry and a chaff industry of national importance, greatly facilitated the later transition of the Shire from a pastoral to a farming economy, and struck a major blow to Melton township’s era as a wayside town servicing Ballarat road (especially coach) traffic". Melton Railway Bridge being built across the Werribee Rivertransport

In the 1650s, the newest exciting development had arrived on Britain’s shores, this time it was tea from China. As it was brought back from overseas, tea was incredibly scarce and as such its price was very high; in 1664, the cost of tea was already 40s per pound, although this is not as high as what it would become when taxed in the 18th century. This resulted in only the social elite enjoying a cup of tea, and most commonly tea was enjoyed in coffee houses, and teapots were therefore not yet a household item. As the East India Company imported larger quantities of tea, it became more widely available and a larger section of the British population were able to enjoy it meaning that, by 1669, tea was available nearly everywhere. Likely due to the fact that tea was first enjoyed in coffee houses, the first known teapot resembles a coffee pot, with a tapering cylindrical shape and standing much taller than what we now know as a teapot at 13.5 inches tall. Into the 1680s, these teapots were given a conical cover for the spout that was fixed to the pot via a chain. As Queen Anne took the throne in 1702, teapots had become much more widely used and had formed two common groups. The first style of teapot was the pear shaped style which began to appear in 1705. The pear shaped pot usually had a domed lid and sometimes featured a finial. This form was generally supplied with a heater and stand as well as having a baluster shaped handle on one side. This iteration would disappear by 1725 but does make a reappearance in the 1740s, only this time as an inverted pear shape. The second group was the more spherical, or globular, shape which appeared in 1710. The globular teapot had a flush, hinged lid as well as a narrow moulded rim foot and a straight sided, tapering spout. Both generalised groups of teapots have polygonal examples – that is, teapots that are made up of straight sided segments – but six or seven sided teapots are incredibly rare. There is one known example of a seven sided globular teapot, made by Isaac Ribouleau in 1724. This is so unique because polygonal teapots are much more technically difficult and time consuming to make. Other than the occasional band of engraving round the shoulder of the teapot, they remain quite plain until c.1740 when scrollwork and chased shells begin to be applied for decoration. ‘Chasing’ is the process of decorating the front of a piece of metal by indenting the back, without cutting or engraving. From 1755 until 1770, silver teapots became incredibly uncommon and it is likely that this either reflects a change in drinking habits or changing trends producing a favour for porcelain. This dip in popularity could also be in response to the outrageous taxes placed on tea, up to 119%! In 1765, the Leeds creamware globular teapot seemed to kickstart a resurgence and this, combined with the Commutation Act of 1784 – which reduced tax on tea from 119% to 12.5% – saw teapots return in all their forms. It’s around this time, in 1780, that a form of teapot with a detachable, openwork stand appeared; however, the plain, oval teapot remained the most popular in the 1780s and 90s. In the later years of George III’s tenure on the throne, during the last decade of the 18th century, there was a revival of chasing and embossing teapots with flower and foliage designs. At the turn of the century, the spherical, partly fluted teapot with classical decoration was superseded by a more oblong shaped pot that sat on four spherical feet. This was then changed again when teapots became more melon shaped. It was at this time that the capacity of a teapot greatly increased and the previously wooden or ivory handles were replaced by silver handles with ivory washers for insulation. As Britain entered into the Victorian era, the design quality often suffered as there was a tendency to over-decorate the silver. In the early 19th century, the last major addition to the shape of the teapot, a raised collar was added between the cover and body. Whilst this seems to just be for decoration, there is some speculation that it could also be to prevent overspills. https://www.marklittler.com/silver-teapots-history/ This item shows that silver and silver plated teapots were used for tea making.Plain sliver teapot. Heavy oxidation. Dented.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, teapot, silver, siver plate, tea

Light and dark grey fabric with small geometric patterns. Empire line dress with long sleeves. The bodice has two panels with diagonal pleating to shape the bust line. There are two pleated pieces at the shoulders with three pleats (12cm) into which raglan sleeves are attached. The front RHS panel crosses over the left to form a V neck line. The back has a high round neck line and plain back with two darts from the waist. The long sleeves taper to the waist with a top seam. Two small pleats gather the fabric at the top of the wrist/sleeve. The skirt is made up of nine pieces -a front slightly flared panel with 2 gored panels on either side. The back is made up of four gored panels. From the level of the waist, the skirt is lined with stiffened paper like lining. From the waist to the under bodice seam it is not lined. Centre back opening has 29cm zipper at centre back beginning 25cm below the neckline.Tag stitched inside back neckline Styled by Walton Gowns Melbourne All Rayoncostume, female daywear, dress

Clothing. Woman's grey, cream and black dress, with fine all-over swirling fern leaf design fabric.Eleven gores in skirt, home stitched dress. Long sleeves with a turn-back cuff 5cm wide at the peak, tapering to 2.5 cm wide at the 4 cm long opening, which fastens with one metal press-stud. The cuff is trimmed with decorative rouleau loops and coils, giving a flower petal effect. This effect is repeated on the peaks of the revere collar. A rouleau looped bow trims the centre front neckline. A shaped, peaked band on the front bodice extends from the side seams to give the effect of a belt at the back. This is stitched in place and trimmed with three rouleau coils-centre coil 2 cm in diameter, flanked by two coils 1-2 cm in diameter. Skirt has three stitched down pleats, ranging in length from 7 cm to 8.5 cm long,on either side of front skirt.costume, female, woman's grey.cream and black dress

Clothing. Fine white linen fabric. A .8 cm 'tuck' edged at top and bottom with a spoke-stitched border, marks the waistline. Below the waistline is a peplum, split at the centre front with 8 cm deep peaks. These peaks are repeated at the centre back. The peplum tapers to 7 cm deep at side seams. The camisole is trimmed at the top edge with a 4 cm deep band of cotton lace. The top edge of the linen fabric has a double row (off set) of cotton embroidered 'spots' 2 mm in diameter, and three rows of drawn thread work - one cm in width, 3.5 cm wide lace form the shoulder straps. The back opening fastens with six tiny 7cm pearl buttons, and hand-stitched button holes. The lower button fastens with a loop at the waistline 1880-90's. A 'fan' of pintucks, arched from 4 cm long at the ends, to 6 cm long at the centre, fans the midriff at the centre front, above the waistline - 28 tucks in total.costume, female, camisole.

Statement from F. W. Milne & Son, Merchants and General Engineers, Vine Street, Bendigo to North Deborah G. M. Co. N. L. Copy of statement for the month of July, 1958. Top of the page is printed with 'F.W. Milne & Son, Merchants and General Engineers' of Vine Street, Bendigo and the name and types of goods and services offered. Statement is for repair to boiler feed pump, turn taper on end of rock drills to suit sample, make a mild steel cross head wedge to suit sample, supply of bolts, make dies and remove dent from tube of telescopic drill bar, make mild steel split clamp nut to suit sample, make 2 mild steel screws 2 1/2'' x 5/8'' with hexagon head 1'' across flats 1/2'' long and thread to suit sample. Statement is a typed, carbon copy. It has copy written in pencil under the typing. Albert Richardson Collection. document, gold, north deborah g. m. co. n. l., north deborah g. m. co. n. l., statement to north deborah g. m. co. n. l., f w milne & son

Black Cast Iron Coffee Grinder With Circular Copper Bowl on top and a curved metal handle which is attached to a central grinding mechanism. Main body shape almost square tapers slightly closer to the top. Coffee grinder has a large pullout tray contained in the bottom of the mill. 140 cm High x 40 cm Wide Previous Catalogue Number 103 Inscription T & C Clark & Co Manufacturer Additional Inscription contained in an elliptical brass plaque Paris Silver Medal 1878 Awarded T. & C. Clark & Co. Plaque Also contains images of a replica of the Jules-Clement Chaplain Art Nouveau Designed Silver Medal Exhibition Prize, Consisting of a laureate bust of Marianne Facing Left surrounded by the words Republique Francaise. Beside It An Image of Victory Hovering Above The Exhibition Wearing A Laurel Wreath Blowing A Bugle Announcing Manufacturing Success & Excellence & Below Him Cupin (Child Genius) Holding A Banner With T & C Clark & Co. Around The Outside Edge Exposition Paris Universelle Internationale De 1878.T & C Clarke Manufacturerdomestic equipment, food consumption, coffee grinder

Clothing. High lace-edged round neckline - lace 1.3 cm deep. Long sleeves-gathered at the shoulder, and edged at the wrist with a 4.5 cm deep, gathered broderie anglais, featuring a shamrock, and flower design. The bodice has a centre front panel of lace. 9 cm wide at the neckline, tapering to 4 cm wide at the high waistline. This panel is edged with a 4 cm wide scalloped edge at the broiderie anglais trim. Three rows of pintucks, give a finish to the filigree braid, and the gathered broiderie frill. The long skirt is gathered at the lower bodice, and is 70 cms long. The lower 20.5 cms at the hemline has alternate bands of three pintucks, a 4 cm panel of flowers and cutwork broiderie, three pintucks, 4 cm panel panel of broiderie, three pintucks and a 4 cms deep machine stitched hem. Bodice has a back opening, with only one 1 cm diameter covered button evident, a cotton tape passes through a casing, and ties at the back waistline.costume, female, infants nightdress.

This jacket appears to be part of the uniform of a junior officer of the 11th (North Devonshire) Regiment of Foot, a line infantry regiment of the British Army. Several companies of the regiment were stationed in Sydney and Hobart between 1845 and 1857. The jacket was acquired by Brighton Historical Society around 1971 as part of a collection of clothing belonging to the Ward Cole family of 'St Ninians', 10 Miller Street, Brighton. George Ward Cole was an early member of the Victorian Parliament and his family featured prominently in Melbourne Society in their time; the family lived at St Ninians from around 1841 until the early 1900s. It is not known who the jacket belonged to or how it came into the Ward Coles' possession. While George Ward Cole was a military man, his service was with the British Navy and during an earlier period than is indicated by this jacket (1807-1817).A red and green flocked cotton military jacket believed to be part of the uniform of the 11th (North Devonshire) Regiment of Foot. The jacket features a green high stand collar secured at the throat by three brass hook and eye closures. The red jacket bodice secures down the centre front with fourteen brass buttons and finishes approximately at the navel. The bottom line sits on the waistline at the sides and back, tapering lower to the naval at the centre front. The bottom line features two substantial brass hooks one on either side of the waist to secure the jacket to the pants. The shoulder line of the jacket is a neat tight fit on the true shoulder, with a slim fitting curved sleeve with gathered fullness at the shoulder. On each shoulder is a metallic corded epaulet with North Devon XI button and second button with floral motif. At the base of the sleeve is a green cuff like detail with a curved elongated point towards the elbow. At the base of each sleeve is a further two brass regiment buttons. The cream woolen jacket lining is lightly quilted over the breast.st ninians, george ward cole, brighton, military, british army, devonshire regiment, north devonshire regiment of foot

This photograph is taken in the Melbourne District Nursing Service (MDNS) Footscray Centre and shows a Sister receiving sterilized equipment from a Sister in the Autoclave room. The Sister receiving the equipment will use this when giving specific nursing care to a patient in her home.Melbourne District Nursing Service (MDNS), later called Royal District Nursing Service (RDNS), had an Autoclave room in each Centre where Catheter trays, dressing trays, as well as dressing packs and gowns and towels were sterilized for their Trained staff (Sisters) to take to the home when attending to a patient who required specific nursing care. When the Sisters returned to the Centre they cleaned the equipment and set up the trays ready for re-sterilizing. On the right of the black and white photograph is a Melbourne District Nursing Service (MDNS) Sister, wearing a white gown over her grey uniform, with peaks showing, and wearing her grey peaked hat over her short dark hair. She is smiling as she is handing sterilized equipment through the opened sliding window of the sterilizing room. The Sister receiving the equipment is to the left in the next room. She is wearing her grey uniform coat and peaked hat over her short dark curled hair, and is standing against a row of cupboards with their bench top at the level of the sliding window. To her right, a rectangular metal basket sits on the bench top; a white drape is in the basket and another to its right. A four pronged walking stick stands on the floor to her right hand side. At the rear left a small table is against the wall with a small grey square tapering rubbish bin beneath it. The edge of the open door can be seen on the far left. In the foreground some of the cupboards, and part of a wall with an electric switch can be seen.Photographer's stamp. Quote No. GX 6 Handwritten informationmelbourne district nursing service, mdns, royal district nursing service, rdns, rdns equipment, sterilizing, rdns centre

In architecture a corbel serves a decorative as well as structural function as a solid piece of stone, wood or metal that is built into a wall and juts out like a bracket to carry a weight. The smoothly shaped corbel was formerly built into the external wall of the lighthouse facing the sea. It consists of two cupped, rounded forms, one bigger than the other, which are attached to a damaged flat base. Made of cast concrete, it is the same fabric as the lighthouse and shows evidence of white paint on its surface. An early architectural drawing of the tower shows the corbel as a projecting, decorative moulding underpinning the balcony floor associated with the auxiliary light. It indicates the original corbel was a much larger architectural feature which started as a solid rectangular block and terminated with a smaller block and then two tapering, rounded forms. Prepared in mid-1888, the architectural drawings for the lighthouse by Victorian Public Works Department architect, Frederick Hynes, were amended in 1888-89 to provide for an auxiliary light, which comprised an arched opening and door in the tower wall below the lantern room and small balcony. In the late nineteenth century all of Victoria’s lightstations installed a red auxiliary light to serve as a danger warning to mariners sailing too close to shoare. Existing lightstations, like Cape Otway, built a pavilion below their lighthouse facing out to sea, but newly constructed towers like Point Hicks and Split Point incorporated them into their designs. The efficacy of auxiliary lights became a controversial issue and all were discontinued on 1 January 1913. The Point Hicks balcony was removed from the face of the tower in 1971 after it was found to be badly rusted. This resulted in the complete removal of the corbel, from which the rounded moulding and part of the base survives. The auxiliary light and door were subsequently removed in 1975 and glass blocks now fill the opening. Cape Schanck Lightstation retains four cast iron brackets from its auxiliary light balcony which are currently stored in the lighthouse on the ground floor. No other architectural fabric associated with the auxiliary light has been identified at Point Hicks Lightstation. The fragment of corbel has first level contributory significance for its historic and architectural values as a relic of the auxiliary light and as an original moulding from the fabric of Victoria’s first concrete lighthouse.A masonary corbel.

Clothing. Three quarter length sleeves, finished on the outside with a peak, outlined with tiny pink, glass beads-13 cm long. The inner side of the sleeve has three rows of gathering 13 cm long. A peaked collar at the front neckline is also edged with tiny pink glass beads, and tapers in shape at the back opening. This opening is 56 cm long and fastens with 1.2 cm covered buttons and loops, (31 buttons in total). The back centre panel is peaked at the lower edge. Side panels are ggathered at the side seam, and also as they join the front and back centre panels. Circular skirt. A beaded floral motif is stitched to the centre front panel, midway between neck edge and waist. Centre panels extend below the waist at both front and back. An underarm ''protector panel'' under the left armhole with printed motif. Tiny glass beads, beaded flower panels. On underarm protection panel a circular shaped printed label reads: PERFECT FITTING GUARANTEED HYGENIC, REGD. ''ADMYRA''. MADE IN ENGLAND, RUBBER LINED 1585 3- DRESS SHIELDS COTTON AND RUBBER.costume, female, ladies cream synthetic fabric dress

Green and gold shot silk dress. Hemline is edged with a binding of black velvet - one cm wide. Bodice lined with cream linen, sleeves lined with cream cotton, skirt lined with cream linen(?) or cotton(?). Long sleeves are shaped in a ""semi-circular'' shape at the elbow, and taper in at the wrist. Sleeves are trimmed with green fringing, and a flat green satin bow. Wrist is trimmed a 2cm wide band of cream cotton lace. Top of sleeve at shoulder is also trimmed with green and fringing encircling the sleeve top.High round neck is faced with a 1cm band, and a row of the cotton lace. Two bands of fringing give a rectangular "style'' effect on the front bodice, which is fastened at centre front with ten metal hooks, and nine hand stitched ''holes'' to fasten, and one hand stitched loop at the neckline. Fringing continues over the shoulder, into a 5-sided shape across the shoulder blades. Skirt has two pleats on RHS front and two on left hand side of back and a 7cm centre panel of tight pleating. Skirt extends into a train at back. An inside pocket is accessed from under a pleat in the RHS skirt.costume, female, victorian full length dress with train

BHS CollectionFull length royal blue silk embroidered fabric dress with bodice and long sleeves, fully lined with ivory cotton fabric. Hand made. Front of bodice has round neck and dips to a deep V at waistline. Twelve decorative fabric covered buttons from neckline to lower V that taper to stitched down pleats at waistline. Fabric bow at centre front of neckline lined with blue satin. Long sleeves have short capped layer over a flared layer underneath. Top section edged with one row of royal blue cotton fringeing. Lower flared section edged with two rows of royal blue cotton fringeing. Large royal blue fabric bow attached at each elbow. Back of bodice made of six panels to waistline. Centre panel on each side is edged with cotton fringeing. Centre back opening to waist with nineteen hooks and eyes, only one eye remaining. Piping around waistline. Full skirt knife pleats at front below waist. Hemline edged with blue ribbed cotton ribbon. Card inside box with ''Wedding Gown Circa 1850's".costume, female, royal blue silk dress

Context: A brace is a hand tool used with a bit (drill bit or auger) to drill holes, usually in wood. The pressure is applied to the top and the tool is rotated with a U-shaped grip. Bits used to come in a variety of types but today the more commonly used Ridgeway and Irwin pattern bits also rely on a snail point (called the snail), which is a tapered screw point shaped the same as a wood screw thread, which helps to pull the bit into the wood as the user turns the brace handle and applies pressure. The designs used today come from an original idea and pattern invented by John S Fray. Company History: John S. Fray (1833 ) immigrated to Bridgeport Connecticut USA from England in the 1850s and established a working relationship with Nelson Spofford, who held an 1858 patent for a bit brace (the tool could be augured in a continuous circular motion by hand). He established the John S. Fray Co. around the same time and immediately began producing the Spofford bit brace. Fray himself held at least two patents: one awarded in 1869 for a boring brace attachment, and another awarded in 1883 for a tool handle. By 1889, the firm was located at the industrial complex that sits between the former International Silver Company and the former Bridgeport Chain Company on Crescent Avenue and is identified on the Sanborn Insurance Atlas as a manufacturer of Spofford bit braces, hollow handle awl, and toolsets. The company was in competition with Peck Stow and Wilcox Co. of Southington, and in 1898 was enjoined from making a ratchet bit brace for which the latter company held a patent. By the 1920s, the factory had been purchased by the Stanley Company of New Britain and leased to the American Tube and Stamping Company, a manufacturer of brass, copper, seamless, and bicycle tubing, which also ran a rolling mill to the south on Stafford Avenue (now demolished). The Stanley Company bought both mills in 1926, perhaps as a strategic move to be located along the Bridgeport Harbour, through which much of the raw material used in its operations throughout the state came. By the 1950s, the Crescent Avenue operations had been moved to other sites in Connecticut, and Stanley again leased the building to a company called Cornwall and Patterson, a manufacturer of piano hardware. Today the building appears to be vacant. An early carpenters tool made by a well known early manufacturer from America who instigated many innovations to the making of tools. His early pattern for the improvement of a tool that could be used for the boring of holes in wood was a significant step forward. His design for a boring brace attachment and later a specific handle is still in use today and his original brace and bit is now sought after by collectors of antique tools. Spofford Carpenter's Bit Brace metal has bit attached. Wing nut holds bit in place but nut missing. holds bit in place. 285mm long x 160mm Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Clothing. Navy blue silk dress with V neckline faced in soft pink silk, which is overlaid with navy rouleau, giving a ''lattice'' effect, and then the neckline has been bound with navy fabric. The lower edge and side is decorated with three, four-petalled flowers, backed with navy fabric, with navy covered buttons in each centre, and navy tipped, pink rouleau 'stems'. Three X 2 cm diameter navy covered buttons are spaced on either side of neckline. Six X 1cm wide loose pressed(not stitched) pleats and two 2 cm pleats form a panel from neckline to waist of bodice. This pleating continues from the waistline, and is stitched horizontally for 31 cm below the waistline, before falling in a pressed form to the hemline. Back of skirt is plain, with top stitched centre back seam, which opens into a (X2) 5.5 cm wide inverted pleat at centre back. Long sleeves are also pleated-stitched down horizontally, for 17 cms, then pressed(not stitched) to the cuff. The cuff has an 8 cm deep peak, tapering to 4.5 cm deep at the opening-which fastens with two metal press-studs. Sleeve fullness is gathered into the cuff.costume, female, navy blue dress

Clothing. Owners initials prominent on outside. Rectangular in shape, fine grained black leather. The leather forms an external shape, white inside a smaller watermark, black silk pouch has a silver frame and clasp to hold the required items. This is lined with a dark cream watermark silk, and has an outer section with side pocket, containing a mirror, and a smaller inner section divided into purse-like compartments. Each swection has a silver frame and clasp. A small piece of light card -red on one side, and possibly glued as a label on the otherside is the same shape as the handbag, and has printed in capital letters ''NOTE THE POINTS''. This may or may not relate to the bag. The outer leather section is slightly tapered-wider at the bottom, forming slight peaks. The top reflects these peaks, with a 3 cm wide band of leather, shaped wider at the top. 23 cm long at top, 21 cm long at lower edge. Silver metal, upper-case lettering:M-A-B, indicate the owners initials. .7 cm high, 7cm long. Two 1 cm wide, 28 cm long handles complete this stylish bag. Mirror has bevelled edges, and is backed with the same fabric, as the bag lining.costume accessories, female, black handbag with silver initials m-a-b

Light camel coloured silk (in very poor condition). Long sleeves overlaid with fine black lace in a floral design. Stand-up collar, five cm deep is overlaid with the fine black lace, and finished with a corded braid on the upper edge. Sleeves are tightly gathered at the shoulder tapering narrow at the wrist, giving a ''leg-o-mutton'' effect. 12cm wide fine black lace, attached at the neck edge, and shoulders, forms a ''puff'' decorative over the shoulder, and continues in a ''over-panel'' to the waistline. Ten x 1cm diameter plastic buttons, with a floral impression in them (2 missing) and 12 hand stitched button holes form the front opening. From the lower opening, six ''pintucks'' 12 cm deep, open into pleats at the lower edge, giving fullness to the bodice. Four metal hooks are evident on the lower tucked front and seven hand stitched eyelets are indicated, but are now severely damaged. Bodice is boned with ten X 17cm long bones, and is fully lined with cotton.A tiny 8cmX7.5cm, oval-at-one-end, pocket is stitched into the front opening, at the bustline. Back hemline dips to a V shape at centre backcostume, female, victorian bodice - cinamon coloured silk

This dressing gown belonged to Clara Johnstone Miller (nee Bell, 1866-1910). Clara was the only daughter of Mr James Bell, a councillor of the Shire of Leigh (today a part of Golden Plains Shire) and owner of Woolbrook Homestead in Teesdale, near Geelong. In 1888, Clara married prominent businessman, racehorse owner, racing identity and pastoralist Septimus Miller (1854-1925). Septimus was the sixth of seven children born to Henry 'Money' Miller and Eliza Miller (nee Mattinson). 'Money' Miller was a well known financier and politician and reputedly one of Australia's wealthiest people in his time. In 1889, Clara and Septimus moved into the house 'Cantala' in Dandenong Road, Caulfield, where they hosted lavish receptions for Melbourne's elite. Clara was known as a stylish hostess who wore elegant imported fashions. This dressing gown is believed to have been manufactured by Japanese silk merchant Shiino Shōbei. Following the opening of the port of Yokohama to foreign trade in 1859, Shōbei began producing western-style silk garments, initially selling them to foreigners living in Japan and later exporting them around the world, even exhibiting at the Melbourne International Exhibition of 1880. His popular exports included quilted 'at-home' gowns or dressing gowns similar to this one. They had one child, Gwendoline Stewart Miller, who died in 1902 at the age of thirteen of diabetes - a largely untreatable condition at the time (insulin would not be discovered until 1921). Clara died in 1910, aged only 44. Septimus subsequently married Helen (nee Henderson), with whom he had a son, Ronald (1915-1990). The Millers were buried in the Brighton General Cemetery in a large Gothic-style vault. Upon Clara's death, Septimus sent much of her clothing and Gwendoline's to her mother Mary Bell. Some of these items were passed down to two of Clara's nieces, Miss Mary Bell and Mrs Lois Lillies, who donated them to BHS around 1973.A hand stitched purple pink silk quilted dressing gown with pale pink embroidery from circa 1894. The dressing gown is embroidered from the collar and shoulders though the centre front body to just above the hemline, on the cuffs and remaining pocket in a pale pink Perle thread embroidery featuring leaves and flowers. The entire gown is hand quilted with vertical parallel lines. The gown's neckline features a flat collar and the sleeve head fits on the neat shoulder line. The sleeve head is gathered and full tapering to a loose flat cuff at the wrist. The front of the garment is currently secured by fourteen decorative frogs of two different styles, none of which appear to be original. There is also evidence of a fifteenth toggle that has been removed from the base. The gown's original left hand pocket has been removed and attached to an area around the right breast presumably to patch a hole or obscure some damage. It is unknown when these modifications have been made. The back of the gown features a gathered pink and black concertina pleated silk insert panel from the neck through to the base of the garment. The garment is lined with a very fine pale pink silk over the woollen batting.clara miller, woolbrook, septimus miller, cantala, gwendoline miller, caulfield, brighton general cemetery, shiino shobei, s. shobey

BHS CollectionLong sleeved full length dress of black synthetic silk fabric. Fabric has silken feel with a smooth satin like backing. Front has U shaped neckline with panel of cream silk lace extending from shoulder to below neckline(28cm). Back neckline faced with lace fabric. Front and back have a narrow central panel(16cm) of fabric extending from shoulders to hemline. The panels are extended at the waistline to join the front and back with loose tabs.The centre panel on the front bodice is edged with a finely pleated frill of synthetic fabric. The centre panels at front and back are also edged with finely pleated frills, from 42cms above hemline to the hem. The bodice is completed with side panels attached to the centre panel The skirt is completed with side panels attached to the centre panels. Set in sleeves have a squared extension that extends to the elbow. From the elbow the sleeves taper to narrow fitting at the wrist. The upper seam of the sleeves from the elbow to the wrist are edged with a finely pleated frill of synthetic fabric. The upper seam of each sleeve from elbow to wrist have fifteen decorative back and gold buttons stitched along the lower edge of the frill. Dress is unlinedcostume, female, black synthetic silk dress

Before factory production became commonplace in medicine, dispensing was considered an art and pill and suppository machines such as these were a vital component of any chemist’s collection. This mould dates back to the days when the local chemist or apothecary bought, sold, and manufactured all his own drugs and medicines to everybody who lived within the local community. In Victorian times, there was no such thing as off-the-shelf medicine. Every tablet, pill, suppository, ointment, potion, lotion, tincture and syrup to treat anything from a sore throat to fever, headaches or constipation, was made laboriously by hand, by the chemist. Some medicines are formulated to be used in the body cavities: the suppository (for the rectum), the pessary (for the vagina) and the bougie (for the urethra or nose). History Suppositories, pessaries and bougies have been prescribed for the last 2000 years but their popularity as a medicinal form increased from around 1840 - suppositories for constipation, haemorrhoids and later as an alternative method of drug administration, pessaries for vaginal infections and bougies for infections of the urethra, prostate, bladder or nose. Manufacture The basic method of manufacture was the same for each preparation, the shape differed. Suppositories were "bullet" or "torpedo" shaped, pessaries "bullet" shaped but larger and bougieslong and thin, tapering slightly. A base was required that would melt at body temperature. Various oils and fats have been utilised but, until the advent of modern manufactured waxes, the substances of choice were theobroma oil (cocoa butter) and a glycerin-gelatin mixture. The base was heated in a spouted pan over a water-bath until just melted. The medicament was rubbed into a little of the base (usually on a tile using a spatula) and then stirred into the rest. The melted mass was then poured into the relevant mould. Moulds were normally in two parts, made from stainless steel or brass (silver or electroplated to give a smooth surface). To facilitate removal the moulds were treated with a lubricant such as oil or soap solution. To overcome the difficulty of pouring into the long, thin bougie mould, it was usual to make a larger quantity of base, to partially unscrew the mould, fill with base and then screw the two halves of the mould together thus forcing out the excess. When cool, any excess base was scraped from the top of the mould, the mould opened and the preparations removed, packed and labelled with the doctor's instructions. https://www.rpharms.com/Portals/0/MuseumLearningResources/05%20Suppositories%20Pessaries%20and%20Bougies.pdf?ver=2020-02-06-154131-397The collection of medical instruments and other equipment in the Port Medical Office is culturally significant, being an historical example of medicine from late 19th to mid-20th century.Proctological mould for making suppositories.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, suppositories, medicine, health

Before factory production became commonplace in medicine, dispensing was considered an art and pill and suppository machines such as these were a vital component of any chemist’s collection. This mould dates back to the days when the local chemist or apothecary bought, sold, and manufactured all his own drugs and medicines to everybody who lived within the local community. In Victorian times, there was no such thing as off-the-shelf medicine. Every tablet, pill, suppository, ointment, potion, lotion, tincture and syrup to treat anything from a sore throat to fever, headaches or constipation, was made laboriously by hand, by the chemist. Some medicines are formulated to be used in the body cavities: the suppository (for the rectum), the pessary (for the vagina) and the bougie (for the urethra or nose). History Suppositories, pessaries and bougies have been prescribed for the last 2000 years but their popularity as a medicinal form increased from around 1840 - suppositories for constipation, haemorrhoids and later as an alternative method of drug administration, pessaries for vaginal infections and bougies for infections of the urethra, prostate, bladder or nose. Manufacture The basic method of manufacture was the same for each preparation, the shape differed. Suppositories were "bullet" or "torpedo" shaped, pessaries "bullet" shaped but larger and bougieslong and thin, tapering slightly. A base was required that would melt at body temperature. Various oils and fats have been utilised but, until the advent of modern manufactured waxes, the substances of choice were theobroma oil (cocoa butter) and a glycerin-gelatin mixture. The base was heated in a spouted pan over a water-bath until just melted. The medicament was rubbed into a little of the base (usually on a tile using a spatula) and then stirred into the rest. The melted mass was then poured into the relevant mould. Moulds were normally in two parts, made from stainless steel or brass (silver or electroplated to give a smooth surface). To facilitate removal the moulds were treated with a lubricant such as oil or soap solution. To overcome the difficulty of pouring into the long, thin bougie mould, it was usual to make a larger quantity of base, to partially unscrew the mould, fill with base and then screw the two halves of the mould together thus forcing out the excess. When cool, any excess base was scraped from the top of the mould, the mould opened and the preparations removed, packed and labelled with the doctor's instructions. https://www.rpharms.com/Portals/0/MuseumLearningResources/05%20Suppositories%20Pessaries%20and%20Bougies.pdf?ver=2020-02-06-154131-397The collection of medical instruments and other equipment in the Port Medical Office is culturally significant, being an historical example of medicine from late 19th to mid-20th century.Proctological mould for making suppositories.None.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, suppositories, medicine, health

These bottles were common in the late 1800's and 1900's. Bottle Nos 1 and 2 were made by Angus & Co, a Sydney company producing ink and gums (glue and clag) from about 1880 to 1920. Their products were sold in stoneware and glass containers in varying sizes. 1. Small pottery bottle referred to as a "Penny Ink" bottle, made by Angus & Co. The small bottle got its name because of the price of 1d. = 1 penny. This bottle is missing. Nos. 3 and 4 The two tall thin Erven Lucas bottles with handles at the top were usually referred to as "Dutch Gins". In fact they actually contained "'Seltzer Spa water' or a form of Quinine Tonic, both supposed to be health drinks. These types of bottles first arrived in Australia with the Gold-seekers from Europe. Early samples are somewhat crudely made. The potter would have formed the bottle with a young apprentice applying the handle, name stamp and the glaze prior to being fired in the kiln. There is evidence of fingerprints from these processes on both samples.A collection of five handmade rare stoneware bottles with a salt glaze: 1. Small pottery bottle referred to as a "Penny Ink" bottle, made by Angus & Co. The small bottle got its name because of the price of 1d. = 1 penny. This is missing. 2. Medium glazed brown pottery bottle with a pouring spout (Angus & Co Ink Commercial). 3. Medium glazed brown pottery bottle with a pouring spout (Bourne Denby). 4. Large glazed brown pottery bottle with a pouring spout (Bourne Denby). Sample is from England probably sold for 2/- or 2/6d. Two shillings or two shillings & sixpence. 5. and 6. Two tall thin brown pottery bottles, one with a broken cork stopper and one without a stopper with Erven Lucas Bols - Het Lootsje Amsterdam stamped at the top of both. They were usually referred to as "Dutch Gins". 6. Green/black bottle is a traditional Dutch Gin with tapering sides, which made it easy to remove from the mold after being blown by hand and the cork top was applied by an apprentice. This sample dates from approximately 1900. Earlier samples are very crude with later samples being machine made with embossing.(This bottle is missing, 13.10.2022). 2. 'Angus & Co Ink Commercial' 3 and 4. 'Bourne Denby' stamped inside an oval lined shape. 5. and 6.Erven Lucas Bols - Het Lootsje Amsterdambeverage bottles, bottles, storage containers, stoneware bottles

Clothing. Deep V neckline, front and back, has a tapered tie, at the shoulder to 4.5 cm, and slanted at the lower edge of the tie. The V neckline has a fine binding finish as do the armholes, and the lower edge of the bodice. Shadow, and pulled thread embroidery, in a floral design, outlines the V neckline in the front. A tiny 10 cm x 10 cm heart shaped pocket is bound at the edges and sits at lower right front. A small dart, 1 cm x 6 cm long is below the armholes, on each side seam. Fabric is cut on the cross to add flair. A two cm x 60 cms tie attaches at each side seam, and would tie at the back. Clothing. Pyjama pants have a V shaped waistband 11 cm deep at front and back, below which is a small 1.5 cm wide pleat on either side of front and back. An 11 cm deep plackett on both side seams - on the left hand side two x 1 cm pearl buttons and buttonholes fasten the plackett. The two buttons on the right hand side are missing. A panel of shadow embroidery decorates the outside lower edge of the trouser leg. Fabric is woven with a floral design. Lower edge of legs are finished with a fine binding. 11 cm peak at waistband. Pants with hem 88 cms, width at ankles 64 cms.Silk and Rayon Made in Chinacostume, female, pink silk pyjamas (bodice)

This Post Office Receiving Pillar was restored in 1980 and is now a fully operational Australia Post mailbox. In early August 1980 Prime Minister Mr. Fraser posted Warrnambool’s first commemorative envelope into this restored Post Office Receiving Pillar at Flagstaff Hill Maritime Village. The special limited edition envelopes are numbered 1 – 7000. When posted, the envelopes would have the Flagstaff Hill Logo and Flagstaff Hill Maritime Village’s own postmark of a ship’s steering wheel surrounding a lighthouse and a sailing ship, and were dated August 3 on the First Day Cover. Amongst Flagstaff Hill’s collection is that very first letter posted by Prime Minister Fraser. HISTORY OF POST OFFICE RECEIVING PILLARS In 1851 ‘pillar boxes’ were installed at roadside locations in the island of Jersey, England; they had already been successful in several European countries. The use of new prepaid, adhesive postage stamps as well as the roadside pillar boxes meant there was no need for the public to take a trip to the Post Office just to post a letter. By 1855 London had installed its first six Pillar Boxes. In 1856 the pillar boxes were first introduced in Sydney. These were circular with a crown on the dome, supported by leaves. Early Victoria Mail was originally collected by ‘letter carriers’, first appointed in Melbourne in 1841, equipped with leather bag and hand bell. He wore a red coat with brass buttons and a black top hat! In 1844 two wooden receiving boxes were erected in Melbourne. The first cast iron boxes were installed in South Melbourne (Emerald Hill) and were still in service until 1967. They were a fluted circular design and made in England. In the early 1860’s the ‘low door round’ design posting box was introduced, being circular and surrounded by a crown, with two broad embossed bands around its circumference. The clearance door was in front of the box and low down. These were made in Australia. In the early 1870’s square boxes with a tapering top were being used. These too were made in Australia by different manufacturers with slight variations on style such as the orientation and number of slots. Next came the circular boxes again, similar to the ‘low door round’ but with the clearance door extending to just below the posting slot, often referred to as ‘high door round’. These boxes did not have embossed bands. In 1887 small cast iron boxes were introduced, attached to posts and poles and called ‘lamp post receivers’. Around 1930 a ‘London’ model was used in Victoria. It was copied from the flat-domed type in London but made in Tasmania. [References: Flagstaff Hill Maritime Village records, The Warrnambool Standard, August 1st, 1980, “Stamps.Au” http://www.stampsau.com, 4th April 2011 (Extracted from “Australian Street Posting Boxes” by Ken Sparks – out of print)] Post Office Receiving Pillar, or letterbox.1885 “High Door Round” design. Tall cast iron cylinder with decorative dome cap with crown on top. Side has a slot and a hinged door with handle shaped as a fist. Painted red with gold trim. “POST OFFICE / RECEIVING PILLAR” lettering cast into cylinder. Restored in 1980 and once again operating as an Australia Post mailbox. Commemorative plague on pillar.“POST OFFICE / RECEIVING PILLAR” lettering cast into cylinder. Flagstaff Hill Maritime Museum – Port of Warrnambool. This letter receiver was officially commissioned on 3rd August 1980 by the Prime Minister of Australia, the Right Honourable Malcolm Fraser M.P. on completion of 25 years’ service as the Federal Minister for Wannon.”flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, post office receiving pillar, letterbox, mailbox, australia post

View of the 1875 timber trestle bridge over the Yarra River reproduced from a newsprint image. Also known as Anderson's Creek (Road) Bridge A contract was accepted for William Elliot to erect a bridge over the Yarra River at Warrandyte on Anderson's Creek Road and other improvements for £1,331.6.2 - Gazette No. 143. Tuesday, November 13th 1860 - http://gazette.slv.vic.gov.au/view.cgi?year=1860&class=general&page_num=2161&state=V&classNum=G143&id=). The bridge was washed away by floods in 1863. It was replaced with a taller timber trestle structure in October 1875, designed and built by C.S. Wingrove, Shire Clerk, Engineer and Surveyor for Eltham Shire Council. A replacement for this bridge was commenced in 1955 to cope with increasing traffic and this structure was widened in 2018 to meet further traffic demands. Argus (Melbourne, Vic. : 1848 - 1957), Thursday 23 September 1875, page 7 ________________________________________ THE WARRANDYTE BRIDGE. The ceremony of formally opening the newly erected bridge over the Yarra at Ander-son's Creek was performed on Monday last, in the presence of the members of the Eltham and Bulleen shire councils whose territories it joins, and a goodly number of the residents of the district. The task was delegated to Mr. Cameron, M.L.A., who, after a few introductory remarks declared the bridge to be opened, and christened it the " Warrandyte Bridge." The party then adjourned to Grant's Hotel, where a cold collation had been prepared. The chair was taken by the president of the Eltham shire (Mr. John Bell) and the vice chair by Mr. Kent, a member of the Bulleen council. Mr Robert Williamson proposed "Success to the bridge," coupling with it the name of Mr. Cameron, to whose exertions was in the main to be attributed the erection of that structure which was an ornament to the district and would prove of great service to both sides of the river. Mr. Cameron, in responding, alluded to the great difficulties, mainly of a pecuniary nature, that had been encountered in carrying out the project, and which had only been got over by their united efforts and by the liberal spirit in which the late Commissioner of Roads had dealt with the case. The healths of the contractor and the engineer were also drunk. The bridge is a trussed timber one, resting on yellow box piles sunk into the solid rock, each pier being weighted with 50 tons of stone. The abutments consist of dry stone walls, 6ft. thick at the base, and tapering to 3ft. on the top, the face of the work having a batter of 1 to 1. The length of the bridge is 308ft., there being four openings in the centre of 66ft. each, and two at the ends of 20ft. each. The width in the clear is 9½ft., and the height from the bed of the river about 33ft. The approaches comprise 1,100 cubic yards of earthwork, and the formation of 48 chains of sideling, the whole cost of the work, which was carried out under the direction of the engineer to the Eltham Shire Council, being £1,413.This photo forms part of a collection of photographs gathered by the Shire of Eltham for their centenary project book,"Pioneers and Painters: 100 years of the Shire of Eltham" by Alan Marshall (1971). The collection of over 500 images is held in partnership between Eltham District Historical Society and Yarra Plenty Regional Library (Eltham Library) and is now formally known as the 'The Shire of Eltham Pioneers Photograph Collection.' It is significant in being the first community sourced collection representing the places and people of the Shire's first one hundred years.Digital image 4 x 5 inch B&W Neg B&W Print 12.5 x 9 cmsepp, shire of eltham pioneers photograph collection, warrandyte, bridge

Cream silk satin bodice, with a high round neckline, finished with a seven cm deep, cream lace, boned, mandarin stand up collar - five bones-(one missing) to support the collar. Nine 16cm bones support the shaping of the tapered firmly fitted waist. A ten cm deep yoke at front and back shoulders. Below the yoke is a panel of eleven cm long pintucks right across the front, and on either side of the back. Centre front gathers into a cotton tape band at the waistline. Below the neckline of the centre front, is a panel ten cm deep of cotton lace, then a 13cm deep fine silk, gathered frill, edged with a reinforced silk ruffle. The centre back opening has a double placket, each fastening with alternate hook and eye,hook on either side of opening. Two large hooks facilitate a joining with a skirt.The three quarter length satin sleeves, are a bell shape, and gather into a cream net, eight cm deep band, which fastens with two metal hooks and hand made loops. Over the net is a double frill, 13 cm deep, and edged with a reinforced silk ruffle, as in the centre front panel. This bishop-type sleeve has five X 12cm long pintucks at the shoulderline. A ten cm long row of a feather stitch type of hand embroidery on either side of front bodice-one each side of the gathered centre front panel. Bodice is fully lined with polished cotton.costume, female, cream silk-satin long sleeved bodice