Robin Boyd was appointed Exhibits Architect for the Australian Pavilion at Expo ‘67 in Montreal. In 1966 Boyd travelled to Far North Queensland and the Northern Territory for research – the Expo exhibits included a coral display and native plant garden.Colour slide in a mount. Paronella Park, Mena Creek, outside Innisfail, Queensland, AustraliaMade in Australia / 10 / DEC 66 M8queensland, slide

Robin Boyd was appointed Exhibits Architect for the Australian Pavilion at Expo ‘67 in Montreal. The garden outside the pavilion featured a sculptural pool, a coral display, animal pool, a pit for kangaroos and Eucalypts and other native plants. The indoor exhibits covered aspects of Australian art and culture, architecture, industrial design and scientific innovation, such as the Snowy Mountains Hydro-Electric Power Scheme, the Parkes radio telescope, the design of Canberra, and the Australian way of life.Colour slide in a mount. West German Pavilion, Montreal Expo '67, Canada. (Architects: Frei Otto and Rolf Gutbrod.)Made in Australia / 3 / APR 67M4 / Encircled 28 (Handwritten)expo 67, montreal, robin boyd, slide

Note by T.H. Kneen,19 November 1991, " Not Burnley. Could be Fitzroy Gardens."Black and white photograph. A brick house in a garden or park settingfitzroy gardens, landscape design, park

Amongst Kurth Kiln Cultral Heritage Artifacts assumed left after the Foresty Commission moved from Kurth Kiln to Kalista LowManufactured rusty metal cutting blades attached to metal handle No physical markingsshears

Specifically shaped hatchet with downward pointed blade and stubby short wooden handle 231 SCOTT Trojan

Part of Tools used for making charcoal during WWIIPurpose made Steel Clamp for attachment to to round shaft up to 5cm. Threaded section with "T" bar for tightening: Height 16cm Width 11cm, Depth 5cm Dia of shaft 3.5cm Thickness 1.8cm Plain steel, badly rusted, thread seized upNil

found amongst the tools at Kurth Kiln Part of wood harvesting machineryChisel shaped tool for a machine with a 3.5cm hole at one end. 3cm thick and 6cm wide at the thick end. Could be part of a slasher or hammermillrural industries

Heavy duty hex wheel wrench, losely tied to a piece of flat steel with several turns of steel wire (perhaps for strengthening). Handle Offset 22cm deep by 14cm wide. Flat steel base is warped and has three holes

found a Kurth Kiln amongst the charcoal making equipmentV Pulley Wheel 10cm diameter by 4cm wide, on a right angle steel shaft cirved and hooked for hanging. Bearing seized up

Kurth's kiln used creek water in a series of waterpipes to cool the charcoal below the flash point for extraction during the charing processA cylinder of wood fitted on a 1" waterpipe, secured by an elbow and a 1" locknut. A 10cl long piece of pipe is fitted on the other side of the elbow. The assembly could be part of the kiln water-cooling system

Machinery PartSteel Coil Tension Spring 26cm long. 5cm diameter made with 6mm dia round steel. Around loop at each end in the same plane provides for hooking onto equipment

Teardop shape steel ring with end squared and bent at right angle for 6cm. Possible chainlink or attachment to plant machinery

Dates to the charcoal making period in the 1940sBlacksmith Tongs, 51cm long, jaws 8cm by 2cm. Diameter of handles 1.2cm. Handles badly bent and rusted.

perhaps used to rake out chacoal from kilnFormed Steel Rake or Scraper, a half-round steel plate rivetted to a short shaped steel arm. Rounded side of steel plate is ground to an edge

Heavy Duty Rake, with attachment to 2.5cm waterpipe fitting. 8 steel prongs are fitted with a flat steel scraper (50 x 8cm x 3mm) at the end, held in place with two steel clamps and two hex bolts and nut each

Heavy Steel Shackle made from 3cm round steel. 10cm internal depth and 3cm clearance. 3cm threaded bolt with square head. Short section of torn 1.5cm wire rope still attached

A 10cm round cylinder of wood on a 1.2cm round steel shaft, shaped into a 15 x 15cm crank handle. Both ends of the wood are banded with 2.5cm flat steel, fastened with bullet head nails

Ratchet Assembly on a flat surface cast bearing; one side broken off. 10cm dia ratchet wheel held in position by a locating pin. Captive handle 1.2cm round steel 35cm long. A 15cm piece of chain is attached to the shaft.

Stranger Stone (Concrete?) Column, cone shaped with hollow cavity in bottom7cmwide by 23cm deep. Two mounting holes in rim of base 2.5cm dia x 23cm deep. Undetermined use.

Small Trolley Axle with centre pivot, 32cm long, 4cm wide and 1cm thick. Axle bearings are formed 1.5cm diameter. Captive centre pin 14cm long, 1.5cm diameter.

20cm dia Cast Iron Trolley Wheel with 4 ribbed spokes. The rim of the wheel is slightly rounded. Axle hole is 2cm dia.

The authors personal experiences visiting Kurth KilnKurth Kiln at the time the Friends of Kurth Kiln were formedTwo Page Article in the publication "Victoria's Heritage" by Mary Ryllis ClarkCopy shaded pink

Although the Beenak Post Office officially closed on 31 August 1951, the Mail Box continued to be used until 1976. The history of Beenak (the town that never was) is part of the Yarra Valley Ranges, and this picture tells the story of the historic MailboxBlack and White Picture of the original Beenak Post Office Letter Box, used for collecting mail during the Beenak Sawmilling operations. The Friends of Kurth Kiln have errected a Commemorative Plaque on site next to the huge gum tree that still carries the scar where the the mail box had been mounted. A full scale replica of the box has been fitted to the shed at Kurth Kiln, made and painted by Henk Bouck under the supervision of ex PMG officer John Waghorn beenak, post office

The Unit was picked up from a paddock on a farm in Bagshot, near Bendigo. It was donated to the Friends of Kurth Kiln Heritage Collection by the Family of Cyril H Peatling on 23 December 2006.Gas Producer Units are of significance to Kurth Kiln because they demonstrate the enduse of the charcoal that was created at Kurth Kiln. Considerable documentation has been made available to us on its history, including a picture of the truck is was mounted on. A Gas Producer Unit that converted charcoal into a gas suitable for the combustion engine. Used on motor vehicles during WWII petrol rationing restrictions. It consists of a hopper to hold the charcoal and a firebox to generate the gasNameplate missinggas producer, bagshot, wilma

The Gas Producer is fitted with hinged mountings for attachment to the rear of a vehicle. Its central oval hopper is flanged by two round containers interconnected with 50mm tubing A faded brass nameplate identifies the unit as a Cheney - Pederick make