Small object with tapered wooden handle and a metal (smoking) pipe/cup like end. Hollow inside metal section and slightly battered. Wooden handle has black flaking paint.

Troy weight is a system of units of mass from an unknown origin. While the name Troi is believed to have come from Troyes in the north east of France the system used primarily in the precious metals industry and adopted in Australia originated in 15th century England. Troy weight units are the 'grain' and 'pennyweight' (24 grains), the troy ounce (20 pennyweights), and the troy pound (12 troy ounces). One troy ounce equals 31.1034768 grams. The troy ounce and grain were also part of the apothecaries' system and was long used in medicine, but has now been largely replaced by the metric system (milligrams). When the Weights and Measures Act was passed in Victoria in 1862 local inspectors were established throughout the colony to ensure accuracy particularly in the weighing of gold. By the 1870's each local council had a set of standards that were used to test the scales, weights and measures of local merchants and businesses. This set would have been de commissioned some time after 1947 and was offered back to the Borough of Eaglehawk in 1989. Hinged, lockable wooden box with brass handle, hinges, latches and lock. Remnant wax on front face of box above and below lock. Interior of box is lined with purple velvet which is worn in several places. Box houses nine troy weights ranging in size from 100oz Troy to 2oz Troy. 1oz Troy is missing. Accompanying set is a two page letter from Weights and Measures Branch of Consumer Affairs offering set back to the Borough of Eaglehawk in 1989. Troy Weights: Part a) 100oz Weight, 68 mm Diameter at base x 113 mm H b) 50 oz Weight, 53 mm D x 90 mm H c) 30 oz Weight, 45 mm D x 77 mm H d) 20 oz Weight, 39 mm D x 65 mm H e) 16 oz Weight, 37 mm D x 60 mm H f) 8 oz Weight, 30 mm D x 47 mm H g) 4 oz Weight, 24mm D x 36 mm H h) 2 oz Weight, 19mm D x 28 mm H i) 1oz missing Hinged Wooden Box: Part j)171 mm H x 300mm W x 196 mm D Typed two page letter: Part k) 295 mm H x 210 mm W x 1 mm Top Troy: Each Troy weight stamped with small symbol made up of the number 5, an image of a crown and the word STANDARD. Side Troy : Each Troy weight stamped with small symbol made up of the number 5, an image of a crown and the word STANDARD above a series of date stamps recording every time the weight was tested. Date stamps: 30.4.1866; 16.9.81, 30 12.86; 1.2.92; 10.5.97; 15.1.04; 10.2.09; 17.12.14; 20.4.20; 29.9.25; 23.1.31; 18.6.36; 14.7.41: 11.7.47 Exterior Top of Box: Remnant of paper pasted to wood. Faint printed text 'ON HIS MAJESTY'S SERVICE'.borough of eaglehawk, making a nation exhibition, city of greater bendigo commerce

Trunk belonged to Godfrey Hirst and was used in his travels between Australian and England. Godfrey Hirst's first trip to Australia was in 1885 and his last trip was in 1916. In this time Hirst was known to travel between Australia and England regularly on the lookout for the latest updates from England that he could bring to his factory in Geelong. The trunk was donated by Susan Wiffen (née Betts), the great granddaughter of Godfrey Hirst. Godfrey Hirst set up a successful woollen textile factory in Geelong in 1888. The factory stayed in operation until 1966. The company still bearing his name has since been purchased by various investment companies but continues to be the largest carpet manufacturer in Australia. Predominately black trunk with two wooden bands around the sides of the trunk and five across the top (lid). The lid is slightly curved and contains white printed lettering GODFREY HIRST. The trunk also contains small wheel underneath locked for pushing the trunk sideways only. The trunk contains two leather handles on either side. Internally, the trunk contains three levels of storage with baskets stackable on top of one another. The baskets are finished in a white and brown striped fabric which has red taped edging for additional strength. The top layer of baskets also has brown leather latches in order to keep the basket lids shut. The layered levels of storage are synonymous of Saratoga style trunk.Printed. Letters: Godfrey Hirstgodfrey hirst

Wooden box with brass top and 24 knobs (22 larger and 2 smaller) on the right-hand side. In addition there are two extra knobs on the right side of the top, as well as two removable oval access panels with handles on each of the ends.Stamped on top of box: a coat of arms 'HARTMANN OF BRAUN A/M' 'RICHTIG BEI / 20 / GRAD CELSIUS' increments for measurement On front side: Sticker labelled 'NATURAL PHILOSOPHY LABORATORY / NO 7 / UNIVERSITY OF MELBOURNE' Stamped on end of metal top: 'No. 2665'hartmann of braun, resitance decade box, resistance box, electical instruments, frankfurt, natural philosophy laboratory

Black metal lamp with handle attached to top. Lamp is a rectangular shape with small curved section on top. Top of lamp hinged to allow access to inside section. No glass on side panels. Small cylindrical section in centre of inside section of lamp presumably to hold light source (candle?) Further research required re operation and provenance of lamp.gold mining, mining equipment, lamp

The candlestick holder was found down the well during excavations, whilst restoring the Mont De Lancey homestead. It belongs to Mont De Lancey.A sky blue enamel candle holder with a handle. It has a small burnt down candle in it, with four used matches in the dish. The blue enamel is chipped in some areas.chamber candlesticks, candle holders, enamelware, functional object

These are two vintage small cups, probably dating from early in the 20th century. They may have originally had saucers to match. Both cups have different inscriptions, and were likely given as a present to indicate friendship or love and other examples of the same type of cup have similar inscriptions such as 'Remember me' and 'Forget-Me-Not'. The cup may not have been used but kept for decorative purposes.This cup has no known provenance and is kept for display purposes as an attractive vintage household itemThese are two small china cups with a light greenish yellow and white body and a white handles. The white section has some gold lettering on it. The cup is decorated with s raised pattern of a gold chain and blue and gold flowers. The country of origin is stamped on the base..1 A Present .2 Remember me. Made in Germanysmall china cup, vintage china, household decorative items

Vessels for storing water such as these are common throughout the ages and evident in the pottery of the middle east, Mediterranean and Africa. Between 1880 and 1910 Bendigo Pottery produced these as part of their terracotta ware range. Established by George Guthrie in 1857 (about 5km north of its current site) and then again seven years later in 1864 after it initially closed, Bendigo Pottery remains one of the most influential and longest running Pottery’s in Australia. Over the years the Pottery has contributed to the growth and development of the district through both its products including building products, table ware and decorative and commemorative war as well as artistically, being responsible for training and supporting many potters locally. The City of Greater Bendigo has had a long history of partnering with Bendigo Pottery to produce tourism tableware and art pieces and the Civic Collection holds a number of important items within its collection.Polished terracotta water holder with saucer and stopper. Globular body with rounded base. The shoulders taper into long cylindrical neck, no handle or pouring spout. Surface is undecorated expect for two rings at base of neck. This is the smaller of the two. 0430a stopper; 0430b vessel; 0430c saucerNone foundbendigo pottery, george gutherie, city of greater bendigo tourism

A baleen whale has hard bristly baleen that hangs from its upper jaw inside its mouth instead of teeth. Baleen is made from a protein called keratin, just like human hair and fingernails, and its colour can vary between species, from black to yellow or white. The whale uses the tough, flexible baleen like a sieve to catch its food, filtering the small sea creatures out of the sea water it releases from its mouth. In the19th Century, whales were hunted for the products that could be made from their bodies, such as oil for lubricating machinery, soap making, lamps, heaters and fuel for the lighthouse lights. The flexible baleen was used for whip handles, carriage springs and umbrella ribs. It was also used for the skirt hoops, hat ribs, and rigid ‘stays’ in tightly fitting bodices to enhance their figures. The Southern Right Whales, as well as Blue Whales and Humpback Whales, are baleen whales. The Southern Rights annually visit the ocean off the southwest coast during the breeding season. In the early 1800s whalers hunted along this coastline in their dangerous pursuit of money for the precious cargoes of whale oil and bones. The population of these large animals dwindled quickly and by the late 1840s the whaling industry dwindled. Whaling recommenced from the 1940s to the 1980s when the whale products were used to make margarine and dog food. The baleen sample has been used to educate people about whaling and about the properties of baleen. The baleen sample is significant for its association with 19th century women's fashion. It helps to understand how garments were supported to shape a woman's figure. The baleen sample represents a period when whales were hunted and killed to provide income and products for for the local settlers and for the export industry.Baleen sample from a whale's jaw. Its black shiny hard yet flexible surface is slightly rippled and textured. One end is fringed and the other and a smooth cut edge. The colour varies in places, with stripy brown colouring. flagstaff hill maritime museum and village, great ocean road, shipwreck coast, baleen, whalebone, baleen whale, keratin, 19th century, whaling industry, women's fashion, stays, bodice, women's figures, fashion, clothing, whale oil, baleen colour, whale hunting, whale products, southern right whale, blue whale, humpback whale, southwest victoria, whalers, whale bones

Small metal wrench with wooden handle. W & B Made in USAW & B Made in USAtool, "w &b", wrench

Used by donor's family in the 1950s,60s,70, & 80s. They were originally made at the Commonwealth Aircraft Factory after the war to use the facilities available.Namco Pressure Cooker - a large heavy aluminium saucepan with a close fitting lid which seals on a rubber ring (missing). The lid is locked in place by wide interlocking lugs on the saucepan and the lid. It has a gauge to indicate pressure and a lever and seal system on the lid which locks into safety lock. The safety lock includes a stem release hole in which a small round plug is inserted. The pressure can be adjusted. Also included is a lead safety plug to release the steam if it overheats. Two bakelite covered steel handles aids its use.526Y on both handlesdomestic items, cooking

This button hook was used by Annie Meredith Brown (née Nicholls) and her daughter Annie Meredith Bailey (née Brown). Button hooks were mainly used for doing up buttons on shoes and boots.Small button hook with bone handle, the hook folds inwards and opens out like a penknife.button hooks

In 1854 in Melbourne George Rolfe Senior established an import business dealing in groceries, wines and spirits and tea. His son George, born in England, took over the business of Rolfe and Co in 1871. A keen sportsman, George Rolfe’s love of fishing led him to take frequent holidays in Warrnambool. He began buying blocks of land near the mouth of the Hopkins River in Warrnambool in the 1870s. By the 1880s Rolfe owned 50 acres in the Hopkins River area and named the property, Lyndoch. He built stables, chaff and bone sheds, a jetty, a boatshed, a water well, a windmill, a reservoir and extensive gardens. He also bought the nearby properties of Shipley and Fairy Hill, establishing a stud farm and breeding cattle. In 1891 he married Jane Ann Lake, the widow of his property manager, and when he died in 1919 his step-daughters, Florence and Annie Lake, inherited Lyndoch. The property was sold and became an aged care facility in 1952. The cutlery items were in use in the building erected by Florence Lake in 1920 and known today as Lyndoch but the ‘R’ monogram on the items suggest that they belonged to George Rolfe or even his father before him.These cutlery items are of considerable importance as mementoes of George Rolfe and his family. They were prominent in Warrnambool’s history in the late 19th and early 20th centuries with the establishment and development of the property, Lyndoch, near the mouth of the Hopkins River. These are 17 pieces from a silver cutlery set that belonged to the Rolfe family (one tablespoon, six large forks, five smaller forks, four small spoons and one mustard spoon.) All the pieces of cutlery have a monogrammed ‘R’ at the end of the handles. Twelve of the items are tarnished and one small spoon is very worn. All the items have six hallmarks. ‘R’george rolfe, lyndoch, warrnambool, rolfe & co. melbourne, florence lake, lyndoch warrnambool., history of warrnambool

This is a typical example of a flat wick domestic paraffin lamp used in households prior to the introduction of electricity.A flat-wick lamp is a simple type of paraffin lamp, which burns paraffin drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce. The wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the wick. This has a cooling effect and keeps the wick from over heating. The lamp burner has a flat wick, made of cotton. The lower part of the wick dips into the fount and absorbs the paraffin; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the paraffin that the wick has absorbed burns and produces a clear, bright, yellow flame. As the paraffin burns, capillary action in the wick draws more kerosene up from the fuel tank. All paraffin flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above. (Source: Wikipedia accessed 24 Nov 2023) This lantern has a circular heavy green glass base for holding the paraffin. The base has a 12mm green glass handle. There is a small clear glass chimney with a fluted upper edge and some bubbles in the glass. The metal burner and wick holder has four metal prongs to hold the glass chimney in place. The round metal wick winder is functioning. There is a small amount of residual paraffin in the base. The flat wick is made of cotton.There are no markings to indicate the manufacturer.paraffin lamp, flat wick lamp, domestic lantern

Small footprint tool with "The Footprint" and "Made in England" on handle.The Footprint, Made in England.tool, footprint

Item 1: Wooden castellated rolling pin with handle each end. Item 2: Wooden rolling pin with handle each end, steel "eye" screwed into one end. Item 3: Small diameter wooden rolling pin with handle each end.No visible markingsdomestic items, food preparation, rolling, pastry, baking, pie, food, kitchen.

The clock parts were discovered in 1980 by Julie Wilkins, a Victorian scuba diver who had already experienced more than 500 dives in Australia and overseas. She was holidaying in Peterborough, Victoria, and looking forward to discovering more about the famous Loch Ard ship, wrecked in June 1878 at Mutton Bird Island. The fast Glasgow-built clipper ship was only five years old when the tragedy occurred. There were 54 people on board the vessel and only two survived Julie's holiday photograph of Boat Bay reminds her of her most memorable dive. Submerged in the calm, flat sea, she was carefully scanning around the remains of the old wreck when, to her amazement, a gold coin and a small gold cross suddenly came up towards her. She excitedly cupped them in her hands and then stowed the treasures safely in her wetsuit and continued her dive. She soon discovered a group of brass carriage clock parts and some bottles of champagne. It was a day full of surprises. The items were easily recognisable, without any build-up of encrustations or concretion. Julie secretly enjoyed her treasures for twenty-four years then packed them up for the early morning train trip to Warrnambool. After a short walk to Flagstaff Hill Maritime Museum and Village, her photograph was taken as she handed over her precious find. She told her story to a local newspaper reporter, lunched a café in town then took the late afternoon train home. Her generous donation is now part of a vast collection of Loch Ard shipwreck artefacts, including the gold watch and the Minton Majolica model peacock. This group of brass clockwork parts is incomplete. The pieces were in the ocean for over 100 years before Julie recovered them from the Loch Ard wreck. Their size would suit the works of a carriage clock, with a mainspring and weight to power the clock movement, a pendulum to measure the clock's speed, arbours, posts, pillars and at least one other plate. They would have been mounted inside a protective case with a small door to easily access the clock face for setting the time and accessing the key's winding hole. The clock cases were usually made from decorative gilt brass with a glass front and a carrying handle. The parts include a weighted second hand with a decorative four-pronged finish at one end, a rounded weight at the other, and a hole for attaching it to the clock face. The gear teeth profiles are ‘cycloidal’, an arch shape with vertical sides, which is common for antique clocks. Modern clockworks have ‘involute’ teeth with sloping sides and a squared-off top. The brass carriage clock parts are an example of a mechanical clock produced in the 1870s. The clock's design is a part of the chain of technological improvements in methods for timekeeping. Its cycloidal gear teeth were the forerunner of the more modern involute gears. The group of clock parts includes a weighted hand or arm for signifying the seconds. This feature was uncommon in portable Victorian-era clocks. The clock parts are also significant for their association with the ill-fated sailing ship Loch Ard, wrecked in 1878. The travelling clock or officer’s clock may have been part of the cargo destined for the 1880 Melbourne Exhibition, or the personal possession of one of the people on board the vessel. Brass clockwork parts from a mechanical clock, sixteen pieces. Parts comprise a plate, large gears or wheels, small pinions or wheels with fine teeth, wheels with cogs, and a weighted second hand. The parts were from a carriage clock ca. 1878. They were recovered from the wreck of the sailing ship Loch Ard.flagstaff hill maritime museum and village, warrnambool, great ocean road, shipwreck coast, loch ard, wreck of the loch ard, 1878, mutton bird island, peterborough, scuba diver, 1980s, shipwreck artefact, relic, clock, mechanical, clock parts, time, timekeeper, horology, chronometry, cogs, time keeping device, scientific instrument, chronometer, john harrison, longitude, carriage clock, coach clock, portable clock, travelling clock, travel clock, traveller’s clock, officer’s clock, weighted second hand, victorian era, cycloidal gear teeth, brass clock, julie wilkins

Object. Handle engraved with the owners initials - MB. A ''knob'' at the top of the handle, has a foliage type design impressed in the steel. This continues down each side of the handle, finishing with further decoration at the base of the handle. Just beside this lower decoration, on each side is a hallmark, now very difficult to read. A small one cm. diameter hook at the lower edge of the tapered shaft.On the shaft of the hook - ''English mane ? Or make? Steel . On handle MB in ornate engraving- (Maggie Barber).personal effects, steel button hook

A marine foghorn gives an audible navigational signal to warn vessels of dangers, hazards and the presence of other vessels in fog conditions. The foghorn signal is a series of long and short sounds with short or long pauses between them. These common signals conform to a code called the International Regulations for Preventing Collisions at Sea and provide such information as whether the vessel is under sail or motor, large or small, aground or at anchor. The designs of foghorns vary but they all use a column of air to make a loud sound. Some use vibrating plates or metal reeds, others force air through holes in a revolving cylinder or disc, sounding like a siren, and some use a clockwork mechanism to open the valves that let the air into the horn. They are usually built to meet particular specifications e.g. U.S.C.G. (US Coast Guard). This Tyfon plunger foghorn has a horizontal handle attached to a vertical rod that moves up and down inside a cylinder. When the handle is plunged down, in a similar way to a bicycle pump, the air is forced out of the bottom of the cylinder into a pipe with a bell-shaped horn on the end, making a loud, low sound. The wider base of the cylinder helps to keep it stable. The original type Tyfon foghorns were manufactured in about 1910 by Kochums Mechanical Workshop (Kockums Mechanical Werkstad, Ltd.), Malmo, Sweden. The company was established in 1840, became a Limited company in 1866, and established a shipyard at the Port of Malmo, Sweden, in 1870. The civilian ship production in Malmo ceased in 1987. As well as building ships the company built large industrial and agricultural machinery and maritime goods.this replica foghorn represents the design of a Swedish, Tyfon model 1910. It is an example of the type of safety equipment used on marine vessels to signal other vessels and signal to land. Replica foghorn; portable marine, plunger operation. It has a brass cylinder and adjustable brass horn. The plunger handle and base are wooden. Inscriptions are on the plaque on the horn and moulded into the air intake. Facsimile of a Kockums of Malmo, Sweden, Tyfon model 1910 Fog Horn.Impressed into the attached plaque "KOCKUMS MLK. VERKSTAD / MALMO SWEDEN" and "TRADE TYFON MARK" Also added to the plaque individually "288938" Molded around the circumference of the air intake "TYFON PATENT"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, foghorn, fog horn, tyfon foghorn, kockums mlk verkstad, malmo sweden, replica, warning signal, safety equipment, ship's equipment

Small screw steel with wooden handletool, screwdriver

This rare vintage clothes iron is not just a functional item but a testament to the craftsmanship and ingenuity of an earlier era of the 19th century. Crafted from cast iron and featuring a wooden handle, it is a unique piece that adds a touch of authenticity and history to our collection. The inclusion of a funnel and chimney showcases the attention to detail in the design. A rare cast iron charcoal clothes iron with a wooden handle, complete with a funnel and chimney. The goose neck iron has a hollow base into which charcoal is placed. The small hole at the back has a sliding cover that was used to regulate the draft and temperature of the iron. To keep the charcoal glowing, the cover could be opened to allow more air or oxygen in to encourage the charcoal to burn. The iron could be swung back-and-forward to revive the charcoal. The fumes produced by the charcoal are carried away from the clothes by the large funnel that acts like a chimney at the front of the iron. The holes that line the base allow air to circulate and keep the charcoal ambers burning. This vintage clothes iron is not just a functional item but a testament to the craftsmanship and ingenuity of an earlier era. 'S' is stamped in a circle on the back of the iron.flatirons, laundry irons, cast iron laundry irons

BHS CollectionRound metal cream scooper. Several small holes on scooper for filtering of milk. The scooper has a simple handle. This item could have been used by George Harris.food technology, dairying, metal cream scooper

Four photographs from a Supplement dated Thursday, November 14, 1901. Top photo is a picture of the Victoria Quartz poppet legs, buildings and a large chimney. The second photo is a puddling machine. In the photo is a circular area with water in it and an island in the centre with a log across it. A horse is harnessed to one end of the log. There is a man behind the horse and a dray in the background. The third photo is a whip. It is a pole held at an angle by two smaller poles. At the top is a wheel. There is a rope over the wheel with a bucket on the end. There are two men to the right of the whip. The bottom picture is a man dollying. He has a half barrel and he is working the water with a short pole with a handle on each side. The barrel has a drainage pipe in the bottom. There is also a dish, two buckets and a shovel around the barrel. There are two photocopies of the page. One didn't get all the fourth picture copied.photo, victoria quartz, victoria quartz, photographs of mining, puddling machine, whip, dollying

2nd INF Brigade Competition - Lewis Gun - Won by 5th BattSmall - Mid size trophy with upside down hockey stick/nike logo handles that are intact. Base of trophy has VSR Trust written. 2nd INF Brigade Competition Lewis Gun Won by 5th Batt5/6 rvr, 5/6 rvr pipes and drums, 2nd inf brigade competition, lewis gun, 5th batt

BHS CollectionSmall metal jug (possibly made of pewter). The jug has a decorated handle. The lid has what looks like a bird of prey, on three leaves, a snake is sliding out behind the bird. On the bottom what's looks like an H has been scratched on. From George Harris estatedomestic equipment, containers, jug

Wooden Wax Sealing stamp - wood handle with a small brass stamp with the letters "R.Ty." and "I" or "1" underneath. See e-mail message from Andrew Cook dated 3-2-2019, Andrew advised "That is a wax seal (see attached image of a modern day one). You can still buy them to this day. I'm only guessing, but maybe the seal came from one of Melbourne's cable tram depots? 'R' could possibly stand for 'Richmond' or maybe 'Revenue'. See: https://milligram.com/creativity/wax-seals - accessed 22/2/2019 for samples of the seals and the stamps - very similar in design.trams, tramways, mmtb, revenue clerks, tickets

Rowing trophy won in 1938 by anticedent unit of 5/6 RVRSmall, Art deco silver trophy with two, double tiered handles on long ornate stem. Engraved on obverse United Services Regatta 1938\Championship Eights Won By 6th Battalion Bow CPL M Stokoe 2 Pte M.J. Fakhry 3.Pte D.B.Tudehope. 4. Capt H.E. Wright 5. Pte T.D. Nuendorf 6.Pte k.q. nUENDORF 7.Pte H. Gunnerson Str Sgt F.F. Knowles Cox Capt H.E. Comporl Coach Capt T.F.Davies6th battalion, interwar, trophy, rowing

Small silver trophy on bakelite base. Stem has separated from cup. Left handle has been bent . Cup lip has been flaired out and has engraving on it obverse is hand engraved Drumming Contest Ballarat 1956 1st Prize VSRvsr, trophy, 5/6rvr pipes and drums