Twin Cylinder Racking EnginesHistoric - Industrial - Twin Cylinder Racking EnginesTwin Cylinder Racking Engines made of metal, iron and steeltwin cylinder racking engines, puffing billy

Clarkat A Clarkat Aircraft Tug that has been converted to run on Rails, This Clarkat 'B' was one of 11 machines shipped on 13 April 1943 to the Lathrop Holding & Re-consignment Depot in Lathrop, California. and was used at Jack's Magazine, Maibyrnong, Victoria and later on at Coal Creek Historical Village, Gippsland, Victoria. Clarkat Tug Model C S/N Cx30F Made by Clark Tructractor Div of Clark Equipment Co Battle Creek Michigan U.S.A Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 Historic - Industrial Narrow gauge railway equipment - Jack's Magazine, Maribyrnong, Victoria, Australia Clarkat Aircraft Tug that has been converted to run on Rails, made of steel Coal Creek Tug Clarkat Serial No. CK 43 470 Code: Heavy Des.Pat. 116092 clarkat, clarkat aircraft tug, puffing billy, jack's magazine

0-6-2 Tank Locomotive No.1 "Delta" Gauge 2'0" Identification: 1 Delta Type: 0-6-2T Builder: Perry Engineering, Mile End, South Australia Builder's number: Perry 7967.50.4 of 1950 Building date: 1950 Current status - Static Exhibit Wheel Arrangement 0-6-2T Cylinders (Diameter X Stroke) 10 inches X 18 inches Boiler Pressure 180 psi Driving Wheel (Dia.) 28 ½ inches Weight 16 tons Coal Capacity 27 cubic feet Water Capacity 500 gallons The Perry Engineering Co, Mile End, South Australia built a total of 18 locomotives for the 2’0” gauge tramways used by the sugar industry in Queensland. This 0-6-2T locomotive was built by Perry Engineering Co. Ltd. of Mile End, Adelaide as their Builder's No. 7967.50.4 of 1950. It was used at Qanaba Mill, Bundaberg where it was known as No.1 "Delta". / Qanaba Mill No.1 No. 1 “DELTA” 0-6-2 TANK LOCOMOTIVE Gauge: 2 foot Built by Perry Engineering Company of South Australia in 1950 (Builder’s number 7967.50.4), “DELTA” is a medium sized Australian designed locomotive featuring Walschaert’s valve gear driving piston valves. Weighing 16 tons (16.3 tonnes) it was one of the post-war narrow gauge steam locomotives, which worked in the canefields of Queensland until 1978. “DELTA” worked at various sugar mills in the Bundaberg area and was finally withdrawn from service at Quanba Mill after a life of 28 years. Obtained by the Puffing Billy Preservation Society in 1981. Delivered to Australian Estates Co., Kalamia Mill named DELTA in 1950. Purchased by Fairymead Mill as No 20 DELTA. Purchased by Millaquin Sugar for Qanaba Mill as No. 1 DELTA, 1970 Withdrawn from service, 1978. Obtained by Puffing Billy Preservation Society for display at the Puffing Billy Museum.Historic - Industrial Narrow Gauge Railway - Steam Locomotive used in Queensland in Sugar Mill service. Locomotive No.1 "Delta" - Steam Locomotive - made of steel, and wrought ironDelta0-6-2 tank locomotive no.1 "delta" perry engineering - puffing billy railway perry 7967.50.4 of 1950, puffing billy, qunaba sugar mill, bundaberg, perry engineering, delta, steam locomotive, 0-6-2 tank locomotive no.1

Malcolm Moore No. 1013 Four wheel Diesel Rail Tractor Gauge 2'0" Malcolm Moore rail tractor (Builder’s Number 1013) It was built for the Australian Army in 1943. It was sold to the Inkerman Sugar Mill in Queensland around 1948 for hauling cane and shunting at the works. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It was purchased from the Inkerman Mill of Pioneer Sugar Mills in 1982. Historic - Industrial narrow gauge Railway - Diesel Rail Tractor - used by the Australian Army and Inkerman Sugar Mill in QueenslandDiesel Rail Tractor made of iron and wrought irondiesel rail tractor, puffing billy, inkerman mill, industrial narrow gauge railway, gauge 2’0”, inkerman sugar mill, australian army

Guards Van Sign - Ticket Office In the Preservation Society days of Puffing Billy, not all stations were manned for the sale of tickets, and tickets were sold from the Guards Van. To advise the public where they could obtain tickets this sign was placed above one of the windows on the guards van. Tickets could be issued from here for passengers to travel on the line.Historic - Puffing Billy Railways Guards Van Sign - Ticket Office sign Guards Van Sign - Ticket Office White enamel sign with black letteringTicket Office puffing billy, station sign, ticket box

Station Sign - Entrance Tickets A sign from the early days of the Puffing Billy Preservation Society era, to advise where the entrance was to obtain tickets for travel on Puffing Billy. Historic - Puffing Billy Railway Station Sign from the early days of the Puffing Billy Preservation Society era. Used to advise where the entrance was to obtain tickets for travel on Puffing Billy. Station Sign - Entrance Tickets wooden brown with yellow lettering painted signEntrance Ticketspuffing billy, station sign

Coxhead Tools Pullers Historic - Industrial - Advertising Sign - Coxhead toolsSign - Advertising - Coxhead Tools Pullers made of paint on sheet metalTools Coxhead Pullers The Head of Qualitycoxhead tools pullers, puffing billy, sign - advertising - coxhead tools pullers

Station Sign - Puffing Billy Direction Trains At Menzies Creek, a Puffing Billy train has had to pass another train since 1966, due to a single line in operation from Belgrave or Emerald / Lakeside / Cockatoo / Gembrook to enable more trains to operate. When two trains passed at Menzies Creek, to assist passengers to travel on the correct train, this sign was erected. The arrows pointed towards the direction of travel as well as the locomotive that was hauling the train. This sign dates from 1975 when the line was re-opened to Lakeside. Historic - Puffing Billy Railway - Station Sign used at Menzies Creek to show next station directionStation Sign - Puffing Billy Direction Trains to Belgrave - Emerald & Lakeside Large rectangle wooden sign Puffing Billy Trains to BELGRAVE Trains to EMERALD & LAKESIDEpuffing billy, menzies creek, station sign

Historic - Industrial - Timber Mill Saw BladesHistoric - Industrial - Timber Mill Saw BladesTimber Mill - Packet of Round Saw Blades made of steelHandle with Care A MSS Product 551 771 MI Melbourne Saw Manufacturing Co. PTY 107 Northern Rd West Heidelberg Vic. Ph 45-4133 puffing billy, timber mill saw blades, melbourne saw manufacturing co.

Historic - Farming - Track tool - Garden ScytheHistoric - Farming - Track tool - Garden ScytheGarden Scythe made of wrought Iron with wooden handle puffing billy, garden scythe

Engine (power producing equipment) A single cylinder Blackham stationary engine. This engine required steam from a separate boiler to operate. Maker : W.H Blackham King Street, Melbourne, Victoria c. 1900 Historic - Industrial - Single cylinder Stationary engine - W. H. Blackham - Kings St. Melbourne, Victoria, Australia A single cylinder Blackham stationary engine. - Made from Iron, wrought Iron & brassW.H Blackham King st. Melbournepuffing billy, blackham, single cylinder stationary engine

Hand made metal bucket with spout leade soldered Bucket marked “ 10 - Not for Mineraleol” Metal bucket with spout 10 - Not for Mineraleolpuffing billy, metal bucket with funnel, tinsmith

Electric staff - Electric staff instruments The staff and ticket system was still too inflexible for busy lines, as it did not allow for the situation where the train intended to carry the actual token was cancelled or running very late. To provide for this, the electric train token system was developed. Each single-line section is provided with a pair of token instruments, one at the signal box at each end. A supply of identical tokens is stored in the instruments, which are connected by telegraph lines. A Staff can be removed from one instrument only if both signalmen co-operate in agreeing to the release. Once a Staff has been removed, another cannot be removed until the token which is "out" is replaced in either instrument. (There are variations on this sequence of events.) By this means, it can be ensured that at any one time, only one token is available to be issued to a driver. Staff belonging to adjacent sections have different configurations to prevent them being inserted into the wrong instrument. Nevertheless, in the Abermule train collision in 1921 and lax working procedures allowed the safeguards provided by the electric Staff system to be circumvented; a driver was handed a Staff for the wrong section, and without reading the information listed on the staff, proceeded on the mistaken belief that the Staff was correct. To prevent this, it became a requirement in the UK for the signals controlling entry to the single line section (starting or section signals) to be locked at danger unless a token has been released from the relevant Staff instrument. Historic - Victorian Railways Electric Staff Instrument Electric Staff Instrument made of Iron , Brass and Glasspuffing billy, electric staff instrument, victorian railways

Station Porters platform Luggage Trolley - two smaller unpainted ones Historic - Victorian Railways - Station Porters platform Luggage TrolleyStation Porters platform Luggage Trolley - two smaller unpainted ones - made of wood and wrought ironstation porters platform luggage trolley, puffing billy, victorian railways

Blacksmith grinding wheel - stone is original but stand has been made by Puffing Billy Museum volunteers stand scrapped - damaged - Feb 2018Historic -Industrial Tool - Grinding wheel Blacksmith grinding wheel - stone is original but stand has been made by Puffing Billy Museum volunteers Wheel made of stone and wrought ironblacksmith grinding wheel, puffing billy

Staff exchanger hoop - Leather Bakelite and wooden prop staff. The hoop held the 'Staff’ giving authority for a locomotive or rail vehicle permission to travel over a specified section of track. The display shows the hand held type used from person to person. Hand held staffs were exchanged at low speeds or stationary. Automatic staff exchangers were also in use when a vehicle was not required to travel at low speed to exchange the staffs and were used by express trains. To exchange the 'Staff’ from the platform or signal box to the locomotive driver, the hoop was held up in the air by the person, and collected by the Drivers arm. The reverse occurred when the staff was being given by the Driver. Both exchanges may occur where one section of line ends and another commences.Historic - Railways - Staff exchanger hoop - used for person to person exchanging.Staff exchanger hoop made of Leather Bakelite and wooden prop staffpuffing billy, staff exchanger hoop

Train Sand Bucket The Train Sand Bucket was usually carried in the guards van of a train and was used to sand the rails when required to provide traction for the locomotive to haul its load up steep grades.Historic - Railways - Train Sand BucketTrain Sand Bucket made of metal puffing billy, train sand bucket

Guards Hand Lamp - Tri Colour Harvey, Shaw & Drake 1913 Gills Alley is located between Queen and Elizabeth streets, extending north to a dead-end from Little Collins Street. In 1895, Gills Alley extended through from Little Collins Street to Bourke Street. The Saracen's Head Hotel was located on the corner of Gills Alley and Bourke Street. By 1920, however, the north end of the lane had been closed off, leaving the sole entrance to the lane on Little Collins Street. Gills Alley was at this time the location of several warehouses, showrooms and factories belonging to the Harvey, Shaw and Drake Company.Guards Hand Lamp - Tri Colour Harvey, Shaw & Drake 1913 used by the victorian railwaysTri Colour Harvey, Shaw & Drake 1913 guards hand lamp Made of Metal , brass and glassTri Colour Harvey, Shaw & Drake 1913 puffing billy, guards hand lamp, harvey, shaw and drake company, tinsmith

Guards Hand Lamp - Tri Colour Historic - Railways - Guards Hand Lamp - Tri Colour Guards Hand Lamp - Tri Colour made of tinpuffing billy, guards hand lamp - tri colour

Tilley Floodlight Projector - Model FL6 It stands about a metre high, and when lit, turns out about 5,000 candle power from the parabolic mirror in the back of the lamp. manufactured between the mid 1940's and early '50's It runs on kerosene that is pressurized with the integral pump, to provide a light beam from the parabolic mirror in the back of the lamp of approximately 3,000 candle power which can project over 1/4 of a mile. It features a pressure gauge, armored glass and all steel construction. Historic - Railways - Tilley Floodlight ProjectorTilley Floodlight Projector - Model FL6 made of metal, brass and glass and steelTilley Floodlight Projector - Model FL6puffing billy, tilley floodlight projector

Brandt Brothers Floodlight Albert Charles Brandt established a lighting business in 1878 with his brothers in Sydney and Melbourne.Historic - Railways - Brandt Brothers FloodlightBrandt Brothers Floodlight made of metal. brass and glassBrandt Brothers - Makers - Melbournepuffing billy, brandt brothers floodlight

Brandt Brothers LampHistoric - Railways - Brandt Brothers LampBrandt Brothers Lamp made of metal and glassBrandt Brothers puffing billy, brandt brothers lamp

The Adlake Non Sweating Lamp "THE ADLAKE NON SWEATING LAMP CHICAGO" Adlake is a shortened name of the "Adams and Westlake" company. They began doing business in 1857 in Chicago. They manufactured railroad supplies and hardware in Chicago. In 1927, they moved to Elkhart, Indiana, where they remain in business today. The difference between "lamp" and "lantern" is that the lamp is meant to be hung on a post or a hook during use and the lantern is hand-held and only used when a person is directing traffic. It has four lenses- two amber and two blue. Adams & Westlake, also known as A&W or Adlake, became a dominant maker of short-globe lanterns and their #200, #250, and plain “Kero” (sometimes known as #300 or #400) models were sold by the thousands to the entire range of railroads. Short-globe lanterns came about because manufacturers figured out how to get a lantern to burn properly with a shorter combustion chamber, which allowed lanterns to be shorter and cheaper. Adams & Westlake began selling #200 Kero lanterns around 1921 and they sold well, the #250 Kero lantern was released in the mid 1920’s as an improvement over the #200 version, with a new burner design. FInally, around 1930 Adams & Westlake released models marked simply “Kero” but are sometimes known as the #300 or #400 models, which are further refinements. The #200, #250, and “Kero” models all look very similar in design and in fact they are all pretty much the same frame design with a couple of minor differences on the later “Kero” models. Short globe lanterns are still very easy to find because they were produced well into the mid 1900s. Adams & Westlake short globe lanterns can usually be dated by looking for a two-part date code on the bottom of the lantern. The first digit will be 1,2,3, or 4 followed by a dash and then a two digit number. Sample code: 2-39 would mean that the lantern was produced in the 2nd quarter (Apr-Jun) of 193Historic - Railways - Adlake Non Sweating LampAdlake Non Sweating Lamp made of metal and glass Metal with handle, painted black, oil Bullseye lens, 13 cm diameter, green Circular lens on opposite site, 5 cm diameter, clear Sliding panel provides access to burner Rain shield embossed 'THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON''THE ADLAKE NON SWEATING LAMP' 'LAMP MFG 7 RLY SUPPLIES LONDON'puffing billy, adlake non sweating lamp

Leather Cash Bag - Kyneton Leather Cash Bag – Kyneton Inscriptions & Markings Kyneton Used for transporting money and other valuable items between a location and Kyneton Historic - Leather Cash Bag from Kyneton stationLeather Cash Bag - Kyneton - small Leather BagKynetonkyneyon, puffing billy, cash bag

fittersLeather Tool Bag - Large A leather bag used by the fitter to carry spanners and other tools required for repairs.leather bag used by fitters on the victorian railways Leather Tool Bag - Large made of leather with copper rivetspuffing billy, leather bag, victorian railways, fitter

fitters Leather Tool Bag - Medium fitters Leather Tool BagLeather Tool Bag - (Medium size)made of leather with copper rivets puffing billy, railway fitter, victorian railways, tool bag

vaporizing kerosene gas lamps of this type were used by track gangers to facilitate night works. Historic - Victorian Railways - Permanent Way and Works - track equipment - Ganger's Lamp made of metal, brass and glass V.R ( and Arrow symbol ) AL 14puffing billy, victorian railways, ganger's lamp

Rail Bender - Part of Hydraulic Rail Bender Rail Bender – No. 3 Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is tightened slowly using large spanner. Historic - Railways Permanent Way and Works - track equipment - Rail Bender large Rail Bender - Part of Hydraulic Rail Bender made of cast wrought iron puffing billy, rail bender

Fire Fighting Extingusher Tank Old style firefighting extinguisher, for use on very small firesHistoric - Railways Permanent Way and Works - track equipment - Fire Fighting Extingusher TankMetal Fire Fighting Extingusher Tank with rubber hosepuffing billy, fire fighting extingusher tank

This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill