The steam engine indicator, or dynamometer, is an instrument used on a steam engine (such as that of a vessel or train) to measure and record the change in the pressures of the engine’s cylinders during their operating cycle. The engineer would use it to identify problems or defects such as bad valve settings or constricted steam pipes. It could indicate the difference in efficiency caused by adjustments made to the engine, being able to instantly measure the variation of pressure from the engine stroke at any given time. This force of power would be registered by a pencil, fitted to the adjustable arm, which would trace a line on paper wound around the cylinder. The recorded information could be used in conjunction with mathematical tables. This particular instrument was made by T.S. Mc Innes, one of the better manufacturers of engine indicators. Mc Innes engine indicators were still being used in the mid 1900’s. This specific instrument was used by Mark Forsythe of North Berwial, Scotland and late of Ararat, Victoria when he was chief engineer on the “SS Talawena” in 1892. The Port of Warrnambool, in Victoria, harboured steam ships that carried both passengers and cargo along the south west coast in the late 1800’s and into the 1900’s. The engineer of a steam ship was responsible for reaching and maintaining the optimum level of steam energy to serve the locomotion and efficiency of the steam ship. The engineer would use a steam engine indicator to measure and record information to achieve this purpose. Engine Dynamometer or Steam Engine Indicator in square, fitted oak case. This brass instrument is used to measure and record steam pressure for setting up and adjusting valves on a steam engine. It has an oscillating recording drum with vertical, silver clip attached for holding paper in place around the drum. The drum oscillates left to right. There is a pulley attached to a length of cord, which is attached to the drum. Beside the drum is a fine metal arm, vertically adjustable, small hole in the end to hold a pencil. Inscription stamped into bracket of the arm. The engine indicator is mounted on a hinged side of the case that swings out ready for use. Attached chains prevent the side from opening past vertical. There is storage for other accessories and an empty compartment in the base (where a scale or ruler may have been located). The case has a collapsible wooden handle, brass hinges and two brass, hook-shaped catches. There is a code stamped inside the lid. It contains a brass, ‘T’ shaped steam-cock (or stop cock) with two open ends made of metal pipe with different sized threads. (Turning the handle on top opens and closes the space in the pipe and would close off the flow of steam from one end to the other.) Also inside the case are three different spiral springs, each with a threaded nut on the end that has a threaded hole inside it. Used by Mr Mark Forsythe when chief engineer on the SS Talawena in 1892 “T.S. MC INNES PATENT” and “522 _ _” (last 2 digits are unreadable) pressed into the arm of the brass indicator. “[ ] X ’ stamped inside the lid of the case. The 3 springs all have a number stamped into them: (1) “32” and “12” (2) “12” and “16” [above] “12” (3) “64” and “150” Card that came with instrument “This instrument was used by Mark Forsythe of North Berwial Scotland and late of Ararat, Victoria when chief engineer on the SS Talawena in 1892" dynamometer, steam engine indicator, t.s. mcinnes, glasgow, dobbie mcinnes, port of warrnambool, warrnambool, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, maritime museum, shipwreck coast, great ocean road

This bookmark was found in a book called 'The English Lakes' owned by Elizabeth Chatham-Holmes. The bookmark is a Stevenograph. In 1854 Thomas Stevens began with weaving plain and fancy ribbons, but was soon experimenting with a development of jacquard weaving to produce pictures. For this, the picture was plotted on squared paper, in the fashion of a cross-stitch embroidery design, and a large card then perforated to represent each colour appearing in every "line" of the picture. The cards, arranged in an endless chain and attached to the loom, controlled the manipulation of the warp threads. Each time the shuttle crossed the loom a different card came into use, changing the arrangement of the warp threads and, consequently, the pattern woven..When the industry collapsed in 1860, Stevens determined to make use of his experiments by producing pictures in such variety as to appeal to all tastes. The earliest productions seem to have been bookmarkers... The pictures included portraits of celebrities and local scenes, scriptural texts, hymns and psalms, and verses from the poets. Stevens also introduced to the Admiralty a hat ribbon with the name of the ship woven in gold wire. This he patented; it was adopted and for many years the firm was the sole supplier to the Admiralty Contracts Department. https://stevengraphs.com/thomstevandh.html Also found in the book was a small card with dried flowers glued with the words 'Flowers from the Holy Land' and a WW2 photograph of the bust of a man in uniform with a cap..1) Red hard covered book called 'The English Lakes' by W.T. Palmer. .2) Woven silk bookmark with white (now cream) and yellow background and red, purple, green and yellow detail and the start of Psalm 23 woven into the bookmark. Possibly made in the late nineteenth century. .3) Small card with dried flowers glued with the words Flowers from the Holy Land .4) WW2 photograph of the bust of a man in uniform with a cap. .1) Inside front cover "E.S. Holmes Ascot" .2) Woven into the bookmark - The Lord is my Shepard I shall not want, & T. Stevens, Coventry .3) Printed on the front - Flowers from the Holy Land, Placed on the Holy Sepulchreholmes, ec holmes, ascot, religious, religion, bookmark, english lakes, w.t. palmer, chatham-holmes collection, flowers from the the holy land, stevengraph

A clamp is a fastening device to hold or secure objects tightly together to prevent movement or separation through the application of inward pressure. The tool is for temporary use for positioning components during construction and wood working. There are many types of clamps available for many different purposes. Some are temporary, as used to position components while fixing them together, others are intended to be permanent. A C-clamp or G-clamp is a type of clamp device typically used to hold a wood or metal work piece, and often used in carpentry and welding. C-clamps or G-clamps are typically made of steel or cast iron, though smaller clamps may be made of pot metal. At the top of the "C" is usually a small flat edge. At the bottom is a threaded hole through which a large threaded screw protrudes. One end of this screw contains a flat edge of similar size to the one at the top of the frame, and the other end usually a small metal bar, perpendicular to the screw itself, which is used to gain leverage when tightening the clamp. When the clamp is completely closed, the flat end of the screw is in contact with the flat end on the frame. When the clamp is actually used, it is very rare that this occurs. Generally some other object or objects will be contained between the top and bottom flat edges. A steel ‘C’ or ‘G’ Clamp used to hold a wood or metal work piece, used in carpentry and welding.L.W.BANKtools, woodwork, metalwork, welding, carpentry, pioneers, market gardeners, early settlers, bank w.l., moorabbin, cheltenham, bentleigh, ormond

Detachable collars enclosed in a leather box such as this one were used in the 19th and early 20th centuries, particularly by men in the business and clerical professions. The collars were attached by studs or buttons to a shirt. The collars were removed prior to shirt washing the shirt. The leather box was most useful for travelling. Detachable collars could still be used today particularly by clergymen. Two are named E R Twomey.This box and collars are retained as an example of vintage men's wear. It will be useful for display.A brown leather cylindrical case with a strap and buckle. It has white thread stitching around the rim and upper edge of the lid, the slot for the buckle, the rim and lower edge of the base . Inside are four detachable white winged collars for wearing with a shirt. Each has three holes, one for a button and two for a stud or for buttons at the front, two wings and a curved slot at the back.They are made of very fine cotton and linen.002215.1 J.T. MADE IN ENGLAND ESPECIALLY FOR Buckley & Nunn Ltd. MELBOURNE 002215.2 A stamped lion, WELCH MARCETSON 7 CO. LTD. 4 THE ALATUS TRADE MARK DES M 9 M 520 1 3/4 x 1/2 T14 002215.3 MADE IN ENGLAND FOR BUCKLEY & NUNN MELBOURNE EXTRA QUALITY , A deer head with antlers in a pointed elipse E.R. THOMEY a red inverted drawn triangle two dots Lindum 2x 151/2 002215.4 MADE IN ENGLAND FOR BUCKLEY & NUNN MELBOURNE EXTRA QUALITY, A Deer head with antlers in a pointed elipse . T indecipherable . E.R.T.4 indecipherable. Lindum 2x15 002215.5 E.R. THOMEY Indecipherable Lindum 2x 15 ? warrnambool, detachable vintage collars, detachable men's shirt collars

In 2005 the H.M.A.S. Warrnambool was de-commissioned in Darwin and the Mayor of Warrnambool, Cr Glenys Phillpot, was present at the ceremonies connected to this event. She obtained this sailor’s hat at that time as a souvenir of the ship. It appears to be brand new. H.M.A.S. Warrnambool was the second ship with this name. The first H.M.A.S. Warrnambool was built in Sydney in 1941 and commissioned for anti-submarine and mine sweeping duties. In 1947 it was struck by a mine in northern Australian waters and sunk with the loss of four lives. The second H.M.A.S. Warrnambool was commissioned in 1981as a patrol boat in northern Australian waters. It had steamed over 500,000 miles before the end of its working life in 2005 and had visited Warrnambool several times. This sailor’s cap is of importance as a memento of the second ship named H.M.A.S. Warrnambool and particularly commemorates the de-commissioning of that ship in 2005 in Darwin. This is a white seaman’s hat with a flat oval-shaped crown made of stiffened white material with two white metal eyelets on each side. The base has a black ribbon with a black bow and lettering in woven gold thread. Inside there is a leather band with a white bow and a navy blue ribbon to act as a chin strap. This is attached on one side only. Inside also is a white label with the maker’s information on it. H.M.A.S. Warrnambool MAPE uniform headwear of the MCH group of companies 3405-66-075-6064 E 5 R.A.N.

RMS Queen Mary a retired ocean liner by 1971 that sailed primarily on the North Atlantic Ocean from 1936 to 1967 for the Cunard Line (known as Cunard-White Star Line when the vessel entered service ( Wikipedia) Maritime ArtLong framed unglazed landscape format painting predominantly depicting in foreground an ocean liner painted black hull and white superstructure with three funnel stacks painted red with black trim, under full sail against a blue sky. The back of the painting is covered with brown paper in places damaged. Hangs on a cotton cord threaded between two screw in eyelet hooks. Brown paper backingat lower right corner single uc word in white paint : "CV WRIGHT (artist symbol of crossed anchors) / 3 ? '71"marine painting, ocean liners, rms queen mary, royal mail ships, p & o steamships, ww2, artwork-paintings, hobbies, bosun, c.v. wright

The sample of crochet lace is an example of a handmade item that would have been used to decorative purpose around the home. It may have been used to edge curtains, a table runner or a mantlepiece. Smaller pieces were used to edge towels. The shape of this piece suggests a possible use as a ladies collar however no tie or buttons have been attached at the ends.The item is significant socially to show the use of textile crafts, such as handmade crocheted lace, to decorate regular domestic objects or create pieces of clothing.A wide length of handmade crochet lace with an open pattern at the top and a pointed edged pattern underneath. For the open pattern mercerised white crochet thread has been used to crochet a double row of a repeat pattern of 'three circles and stems'. Underneath double crochet (US) / treble crochet (UK) is used to create the points which have been edged with the 'three circles and stems' pattern from above.flagstaff hill, warrnambool, maritime village, maritime museum, flagstaff hill maritime museum & village, shipwreck coast, great ocean road, lace, handmade lace, crocheted lace, decorative edging, decorative lace edging, domestic object, crocheted trim, ladies collar, crocheted collar

9062.1 Tatted oblong doily, 13.5cm # x 36 cm L 9062.2 Square crocheted doily, 16.5 cm square 9062.3 Round crocheted doily or jug cover. 25.5 cm in diameter, gathered effect 9062.4 Round 22cm diameter drawn thread doily 9062.5 Round 18cm crocheted doily 9062.6 Round tatted multipoint doily, 9062.7 Small oblong lace doily

This bodice belonged to Mary Crombie, an early Victorian dentist, who lived in Brighton while she was studying at the Australian College of Dentistry in the mid-1900s, and later returned to the area in her retirement from 1949-1971. Mary Margaret Crombie (1884-1971) was born at Coan Downs Station near Walgett, northern New South Wales, where her father Henry was station manager. After Henry’s untimely death in 1895, Mary and her mother loved for a few years with family members in St Kilda, before moving into a cottage of their own, ‘Rosewood’, at 42 Asling Street, Brighton around 1899. From here, Mary attended Oberwyl Ladies College in St Kilda and later the Australian College of Dentistry, one of only a few women to study dental surgery at the time. She was apprenticed to Ada Tovell (1865-1932), one of Victoria’s first female dentists, who had her own practice in Collins Street. Mary graduated in 1907 and the following year moved with he mother to Yarram in South Gippsland, where she took over the running of a practice owned by Sale dentist Charles Trood, eventually purchasing it from him in 1915. Speaking to a Brighton newspaper in 1961, Mary said she believed that she was the first woman to start a dental practice in Gippsland. For some locals, this took a little getting used to: “Many were amazed, and had some misgivings, when they found that the local dentist was a woman,” she said. “I always remember a huge farmer (he was about 6 ft. 4 in.), who had fortified himself at the local hotel to face the ordeal of visiting the dentist. He almost turned and ran when he saw me. … He was still more amazed when I pulled out his tooth without undue trouble.” The farmer was the best advertisement she could have asked for, telling everybody about the diminutive lady dentist who had calmly extracted his tooth. Mary practiced in Yarram until her retirement in 1949. After selling her practice she returned to Brighton, where she spent the last two decades of her life residing at 25 Oak Grove. Following her death in 1971, her relatives in Brighton donated a number of items from her home to BHS.Black satin bodice, boned, with black faceted glass buttons down the front. High collar. Both collar and cuffs are edged with a black net ruffle. Two rows of seven black crochet-covered buttons at each cuff, fastening with loops. Stray brown threads poking through fabric around the collar, shoulders and back indicate that these areas may originally have featured lace embellishments.mary crombie, 1900s

Representative of military issued accoutrements, possibly Australian Army, late 20th Century. Army water canteen, possibly Australian Army issued, with olive green fabric insulating cover featuring flaps with stud fasteners, black twist top lid attached to aluminium body fixed by aluminium chain that is attached both to base and top of lid. Back of fabric cover has a metal prong threaded through a strong fabric loop which has been sewn on for attaching to a belt. Tag on back sewed on which reads 'Made in Japan'. flask, canteen, military, military accoutrements

Representative of military issued accoutrements, possibly Australian Army, late 20th Century. Army water canteen, possibly Australian Army issued, with olive green fabric insulating cover featuring flaps with stud fasteners, black twist top lid attached to aluminium body fixed by aluminium chain that is attached both to base and top of lid. Back of fabric cover has a metal prong threaded through a strong fabric loop which has been sewn on for attaching to a belt. Tag on back sewed on which reads 'Made in Japan'. flask, canteen, military, military accoutrements

NeedleworkBooklet contains sheets of tissue paper Fautley's size , B also iron on transfers. Semco Transfer Frock Sprays BookletSemco Transfer Frock Sprays Folder No.15 Price 3DDistiction and smartness may be added to your frock, jacket or blouse with charming hand embroidery. These transfers are specifically designed for this purpose and can be used on the collar, pockets or anywhere on the garment. If desired additional sheets may be obtained. These designs are equally attractive worked with wool or Semco Embroidery Threads. Semco Art Needlework, Victoriastawell

Auger bits fit into the jaws of a hand brace (brace and bit), which is used to bore holes into wood. The tapered end, or tapered shank, fits into the brace, while the twisted shank and twisted point draw the bit into the wood. The twisted shank guides the bit into the wood, helping to remove chips produced by the cutters and enabling the user to bore deep straight holes. The collection pictured here includes two common patterns of twist bits: the ‘Jennings’ double twist pattern; and the ‘Irwin’ single twist pattern. Their finely pitched threaded points are typically used to cut hardwood timber.Set of thirteen auger bits, with tapered proximal ends and corkscrew spiraled distal ends. Some with tight and loose spiral patterns. Paint spots and surface rust.[size of each bit stamped on]churchill island, tool, auger bits

These boots had a metal plate inserted in sole to protect the feet of personnel wearing boot. This was after earlier boots without this protection did not protect the wearer from sharpened spikes eg bamboo set in pits or “punji” pits, during the Vietnam war. The laces were done up by knotting one end,threading from bottom hole across to opposite hole,up next hole on same side,across to opposite hole etc. This meant that only one loop per opposite holes was all exposed for a quick and easy cutting to release the boot in case of injury to wearer.These boots were typically worn on parade,training and in combat during the Vietnam war era and after.The LEFT boot solid black leather uppers with split leather tongue sewn to sides - making the boot semi water and insect proof.The sole is hard black rubber compound with 7 cleats on sole and 3 cleats on heel,all part of rubber sole. Woven black cotton laces. 30 mm leather reinforcing strip sewn on inside top of boot. 11 by 5mm metal holes per boot for laces. Sole is welded on. “Dunlop made in Australia” and “5/5” on sole in front of heel. Inscribed on top reinforced inside leather band is- “ B 22 R.B.T 1439 188” on one side and “ 5/6” on the other.boots, general purpose, g.p., vietnam war

These boots had a metal plate inserted in sole to protect the feet of personnel wearing boot. This was after earlier boots without this protection did not protect the wearer from sharpened spikes eg bamboo set in pits or “punji” pits, during the Vietnam war. The laces were done up by knotting one end,threading from bottom hole across to opposite hole,up next hole on same side,across to opposite hole etc. This meant that only one loop per opposite holes was all exposed for a quick and easy cutting to release the boot in case of injury to wearer.These boots were typically worn on parade,training and in combat during the Vietnam war era and after.The RIGHT boot solid black leather uppers with split leather tongue sewn to sides - making the boot semi water and insect proof.The sole is hard black rubber compound with 7 cleats on sole and 3 cleats on heel,all part of rubber sole. Woven black cotton laces. 30 mm leather reinforcing strip sewn on inside top of boot. 11 by 5mm metal holes per boot for laces. Sole is welded on. “Dunlop made in Australia” and “5/5” on sole in front of heel. Inscribed on top reinforced inside leather band is- “ B 22 R.B.T 1439 188” on one side and “ 5/6” on the other.boots, general purpose, g.p., vietnam war

The Masons patent of Nov 30th, 1858 phrase was originally embossed on countless glass fruit jars and canning jars, most ranging in age from circa 1858 to the mid-1910s. John Landis Mason was awarded patent No 22186, issued on November 30, 1858, by the U.S. Patent & Trademark Office it was termed an "Improvement in screw-neck bottles", for his invention concerning the process of creating a threaded screw-type closure on bottles and jars. Similar screw-threading had been done before on some bottles, but the process of forming the upper lip area of the container so that it was smooth, even, and sturdy enough for a lid of standard size to be screwed thereon was difficult and expensive to do properly, often with unsatisfactory results. His improvement revolutionized home canning in the United States and many other countries. In any case, throughout the next 60-odd years, production of jars with the Nov. 30, 1858 embossing continued at a high rate, with untold tens of millions being produced. The phrase was soon considered an important marketing device, adding to the perception of quality and reliability of the container to the average consumer. This perception continued to at least 1879 21 years after the patent was issued, nearly every glass bottle factory was likely producing their version. The 1880s and 1890s likely saw the peak of popularity of these jars. A considerable percentage have a mold number or letter on the base, a means of identifying the particular mold in use at the factory.An early item used in most kitchens by women who preserved fruit and vegetables before the arrival of refrigeration giving a snapshot into the domestic lives of families during the late 19th to early 20th century's and how they preserved food for later use without refrigeration. Preserving jar, glass, with metal screw top lid. Glass has side seams, impurities and slightly concave base. It has been hand blown into a mould. Inscription is moulded into glass. Moulded into glass: MASON'S / PATENT / NOV 30TH / 1838"warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, food preserving, mason jar, john landis mason, domestic container, glass jar, fruit & vegetable jar, domestic jar, food preparation, handmade glass, blown glass

The Masons patent of Nov 30th, 1858 phrase was originally embossed on countless glass fruit jars and canning jars, most ranging in age from circa 1858 to the mid-1910s. John Landis Mason was awarded patent No 22186, issued on November 30, 1858, by the U.S. Patent & Trademark Office it was termed an "Improvement in screw-neck bottles", for his invention concerning the process of creating a threaded screw-type closure on bottles and jars. Similar screw-threading had been done before on some bottles, but the process of forming the upper lip area of the container so that it was smooth, even, and sturdy enough for a lid of standard size to be screwed thereon was difficult and expensive to do properly, often with unsatisfactory results. His improvement revolutionized home canning in the United States and many other countries. In any case, throughout the next 60-odd years, production of jars with the Nov. 30, 1858 embossing continued at a high rate, with untold tens of millions being produced. The phrase was soon considered an important marketing device, adding to the perception of quality and reliability of the container to the average consumer. This perception continued to at least 1879 21 years after the patent was issued, nearly every glass bottle factory was likely producing their version. The 1880s and 1890s likely saw the peak of popularity of these jars. A considerable percentage have a mold number or letter on the base, a means of identifying the particular mold in use at the factory.An early item used in most kitchens by women who preserved fruit and vegetables before the arrival of refrigeration giving a snapshot into the domestic lives of families during the late 19th to early 20th century's and how they preserved food for later use without refrigeration. Preserving glass jar. Glass lip with metal screw top lid. Inscription pressed into glass."Mason's Patent Nov 30th 1858"warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, food preserving, mason jar, john landis mason, domestic container, glass jar, fruit & vegetable jar, food storage, preserving jar

This flare pictured is one of three lighting or signal flares. These are pyrotechnic devices used at sea, mainly as a distress signal. However, they have other meanings when used for naval purposes, such as the executive order to start a particular manoeuvre. These are usually packaged as part of a distress pack containing all necessary rockets or flares for immediate use, in any emergency, by ships and off-shore yachts.This set of three flares is significant for its connection with local history, maritime history and marine technology. Lifesaving has been an important part of the services performed from Warrnambool's very early days, supported by State and Local Government, and based on the methods and experience of Great Britain. Hundreds of shipwrecks along the coast are evidence of the rough weather and rugged coastline. Ordinary citizens, the Harbour employees, and the volunteer boat and rescue crew, saved lives in adverse circumstances. Some were recognised as heroes, others went unrecognised. In Lady Bay, Warrnambool, there were around 16 known shipwrecks between 1850 and 1905. Many lives were saved but tragically, eight lives were lost.Flare; mushroom coloured cylinder, metal base with wooden top joined to it. Base has removable cap with metal encased wooden fuse attached, which holds seven removeable pegs and rings. String threaded through top holes has a wooden peg attached. Top also has holes drilled on opposing sides through which the peg would fit. Inscriptions stamped in black on base, and impressed into cap. Stamped black: "I" Impressed into cap: ""I", "R↑L" (inside oval).flagstaff hill maritime museum and village, flagstaff hill, maritime museum, maritime village, warrnambool, great ocean road, lady bay, warrnambool harbour, port of warrnambool, shipwreck, life-saving, lifesaving, rescue crew, rescue, rocket rescue, rocket crew, lifeboat men, beach rescue, line rescue, rescue equipment, rocket firing equipment, rocket rescue equipment, maritime accidents, shipwreck victim, rocket equipment, marine technology, rescue boat, lifeboat, life saving rescue crew, lifesaving rescue crew, rocket rescue method, rocket apparatus rescue, stranded vessel, mortar, life jacket, rocket machine, rocket line, rocket set, schermuly, harbour board, government of victoria, harbour master, armband, l.s.r.c., lsrc, flare, light, safety equipment, distress signal, safety at sea, emergency signal, broad arrow, communication signal, vingage, pyrotechnic flare

This gauge was used in the making of components for the ship model Sovereign of the Seas. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This gauge is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This gauge was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Gauge; marking gauge, wooden. Wooden handle threaded through hole in wooden block, adjusted along the handle by tightening a wing-nut screw. The end of the handle has a pointed pin fitted for scoring a mark on the work surface to mark timber before cutting. This gauge is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, wood working tool, model making tool, drawing instrument, gauge, tool, sovereign of the sea, ship model, hobby, ship model tool

The Ballarat School of Mines opened in the former Ballarat Circuit Court House in 1870. The court house was demolished in 1915 to make way for the Ballarat Technical Art School. The Ballarat School of Mines is a predeccessor of Federation University Australia..1) Handwritten agreement on blue paper with green thread. The agreement is between the Board of Land and Works and Redmond Barry and others concerning a seven year lease of the former Ballarat Circuit Court House for use as a mining school (the Ballarat School of Mines). .2) Four lined fooscap pages relating to specifications of several works required to the Old Court House. .3) Rough notes on proposed lease of the Court House.lease, former ballerat circuit court house, redmond barry, legal, crown solicitor, gurner, robert davidson, warrington rogers, john warrington rogers, william warrington rogers, rivett henry bland, p. saunders, james williams, ballarat school of mines, ballarat school of mines establishment

This item of meorabilia was made by J.G.Murphy while he was hospitalised in the Middle East during the 2nd World War. He later became President of the Red Cliffs RSL and a Life Member of the League for service rendered.Brown leather satchell,embossed with Australian flora and forna, front, back and under flap, there is a carry handle on the top. The front features two Kookaburra like birds, under the flap is a Kangaroo and butterfly and folliage on the back. The seams and handle are hand sewn with 2.5mm leather lacing, and there are press studs to hold the flap closed. There are two internal pockets, stitched with fine cotton thread and the stitching is only visable from the inside. satchell leather, embossed leather, native flora, native fauna, past rsl president, j g murphy, hand made leather work, middle east hospital craft, past presidents, life members, rsl, middle east

Cream coloured hand knitted baby jacket with long sleeves. Fold back collar in zig zag pattern. Body of jacket with vertical zig zag pattern. Sleeves with zig zag pattern. Front opening. Collar, cuffs and hem have crocheted edges in silk thread. Cream satin ribbon tie at neck.This collection of knitted and sewn garments were made in the early 1940s and were intended for a baby that was stillborn.costume, children's, baby jacket

Black and white photograph of two ladies at spinning machine at Hanro factory. Boxes of cones wound behind them. Shelves to right also containing various sizes of spools of thread. Inscriptions: on back - 'On corner (TML) Winding room Hanro. Mrs Dorothy (Gooding) Arichald (sic). Mrs Moroni;, 'Bendigo Historical Society, 'Glad Davis'. "Bendigo Historical Society' (ballpoint pen). 'Glad Davis' TR corner.person, group, employees

Pittock collection : various drill bit drill bits * 18 standard brace and bit drill bits of various gauges 180-95mm length * 2 odd drill bits ( one timber 21mm gauge hole 100mm length & one odd handmade "spade"bit 120mm length) * 4 threaded drill bits 75mm length Items stored in Pittock coach builders box, reference 13000.

About the 1992 Barcelona Olympic Games donator Doug Pleasance wrote- During the 1980s the Australian wool industry was at its most prosperous times with record numbers of sheep producing wool receiving ever increasing values due to the success of the Reserve Price Scheme, and the overall guidance of the Australian Wool Corporation (AWC). As a humble technichian, my role was a low profile newly created position of “Controller, Technical Marketing” where wool was to be marketed on its technical properties, as distinct from the “Product Marketing Group” which exploited trhe traditional high profile approach of marketing wool;s superior fashion attributes. The Woolmark was the tool central to this approach. The 1992 Barcelona Olympic Games saw an evolutionary change in designer selection. A Declaration of Interest Form was communicated to over forty potential designers. The task and especially tight timelines that were involved deterred many aspirants, however, there remained eight designers with the potential we were seeking. These eight designers were paid $3,000 per submission and the winning designer, Wendy Powitt, was paid $15,000. For the first time the judging panel included two athletes, one male swimmer and one female basketballer, their influence was pivotal. The ensemble consisted of three elements- 1. The Official Uniform which was used for travel and all official functions. This included: a tailored blazer and trouser/skirt (all water repellent) by Fletcher Jones, pure wool olive-green faille fabric by Foster Valley, cotton PE formal shirt by Pelaco, pure wool knitwear by Spangaro, printed wool tie by TD Noone, wool nylon socks by Holeproof and footwear by Hush Puppy. 2. Opening Ceremony Uniform a lightweight wool fabric printed with floral designs that had been inspired by the work of Australian artist Margaret Preston. This included: Lightweight W/PE shorts by Fletcher Jones in Foster Valley Fabric, socks by Holeproof and footwear by Hush Puppy. 3. Village Clothing was designed to be highly visible garments to make it easy to ‘spot the Aussie’ and helped to contribute to good team spirit. This included: A pure wool shirt featuring blocks of contrasting colours, and a newly developed stretch 50:50 wool/cotton fabric by Bradmill was made into shorts and jeans by Fletcher Jones.8341.1 - A pair of dark green trousers made from a wool blend fabric. 8341.2 - Green sample fabric with labels stapled on. One staple that was used to attach the label has gone through several layers of fabric preventing it from being unfolded. 8341.3 - Green sample fabric with white thread attached where it has previously been sewn. 8341.4 - Green sample fabric. 8341.5 - Green sample fabric.8341.1 - On label - FLETCHER JONES 8341.2 - on labels- Wool PE. 80:20 FAILLE WEAVEolympics, 1992 barcelona olympics, olympic uniforms, trousers, wool, fletcher jones, wendy powitt

This Belt was presented by the City of Essendon on occasion of presentation of the New Colours 25 November 1956Used to carry the Battalions colours Physical Description Green felt sash with red leather lining. Sash had gold trim and an inscribed silver plate on the face. The battalions battle honours are embroidered in spun gold thread on red silk banners in front of a lightly coloured wattle bush. The regimental badge is spun gold/ silver and red silk. Inscriptions and Markings This Belt was presented by the City of Essendon on occasion of presentation of the New Colours 25 November 1956This Belt was presented by the City of Essendon on occasion of presentation of the New Colours 25 November 195658/32 bn, 5/6rvr, dcoy, uniform

BHS CollectionFine patterned black syntheticed? Thread jacket. Long sleeves have been hemmed back with a generous seven cm hem. This maybe to form a turn-back cuff if required. High fold-back collar fastens with two narrow velvet ribbons. No fastenings at centre front opening. Extended sleeves in one piece with the front and back. Collar, front, and ;lower edges finished in a curved, shell shaped pattern.costume, female, black crocheted jacket