This particular aircraft was modified with a search radar in the lower fuselage to help locate and track targets and was then redesignated as a B-24R model. The RAAF took A72-176 on charge in late 1944 and this saw it issued to 7 OTU (Operational Training Unit) based at Tocumwal, south west NSW. The training saw bomber crews learn how to fly the bomber, operate as a team and work with fighters. Towards the end of the war there were up to 50 aircraft located at Tocumwal along with 5000 personnel. A72-176 was noted as flown on training missions by various aircrew.This aircraft is one of the only remaining B-24 bombers in the southern hemisphere and 1 of only 8 remaining B-24 airframes still existing in the world, out of the nearly 19,000 which were originally built. The restoration honours the contribution of one of the RAAF’s main bombers of the WWII era. This restored Liberator aircraft was assembled from parts salvaged from B-24M models, manufactured during the 1940s in the USA. Made from aluminium, the plane is 68 feet long, with a wingspan of 110 feet, and is metallic silver with a distinctive blue and white target design on each side. The aircraft is powered by four wing-mounted engines, and is fitted with 10 heavy machine guns.Registration number on side of fuselage at rear of plane: 'A72-176' Inscription on side of fuselage at front of plane: 'ROYAL AUSTRALIAN AIR FORCE / US ARMY B24-10 CO / AIR FORCES SERIAL NUMBER 44-41956' aircraft, liberator, bomber, wwii

This type first flew in 1937 and by the start of WWII it was the preferred aircraft in all Empire Air Training Schemes for multi-engine pilot training. By the beginning of WWII the Airspeed Oxford was the preferred aircraft in all Empire Air Training Schemes for multi-engine pilot training. As of April 2014, no Airspeed Oxfords remain in the world in airworthy condition and there are very few complete air frames. There are reportedly some restoration-to-fly projects underway, one in New Zealand.Full-sized replica of an Airspeed Oxford aircraft. This type of aircraft was described as a multi-engine three-seat advanced military trainer monoplane. It was a wooden construction using plywood and fabric covering and powered by two 375 HP Armstrong Siddeley Cheetah 10 engines. Parts originally used a base for this reconstruction were reckoned to be from an Oxford Mk 2 with registration A25 LX181 which was based at Point Cook and used extensively in training from the Werribee Aerodrome.

Between Pratt & Whitney and numerous licensed companies, there were over 180,000 of these engines manufactured in a number of specifications. The B-24 Liberator would have been their major recipient but other famous aircraft using the same engine were the Consolidated Catalina flying boat and the Douglas DC3/C47/Dakota. Refer Wikipedia link for other aircraft that used this engine.As a result of the significant and ongoing usage of these engines in civil aircraft such as the Douglas DC3, they are by no means rare. Many parts can still be sourced new and there are several companies that have the capacity to rebuild these engines to an airworthy standard.The Pratt & Whitney R 1830 is a double row 14 cylinder air cooled radial engine with a capacity of 1830 cubic inches (30 litres), developing some 1200 horsepower at a maximum 2700 rpm.radial engine, twin wasp, r1830

This engine was a Commonwealth Aircraft Corporation (CAC) build, and had been upgraded to 92 specification at some time. This engine as acquired, was completely seized and great difficulty was encountered in dismantling it. The pistons in Nos 1, 13, 3, 2 and 5 had "grown" into the cylinder bores requiring some unorthodox methods to remove them. The cylinder barrels have been brought up to a reasonable standard, those beyond repair were replaced from stock. After getting various parts from the US, this engine was eventually brought up to running order.The Pratt & Whitney R 1830 is a double row 14 cylinder air cooled radial engine with a capacity of 1830 cubic inches, (30 litres), developing some 1200 horsepower at a maximum 2700 rpm.Engine Number 54828

It was constructed on a former Victorian Railways NKS type underframe and powered by a single cylinder, 500 cc B.S.A. side valve motorcycle engine to drive axle by roller chains through an 'Ariel Square Four' gearbox and has traveled on all four 2'6" narrow gauge lines that operated in the state of Victoria.Historic - Narrow Gauge Railway - Track Patrol Vehicle used by Puffing Billy Preservation Society and made from parts of a Victorian Railways track patrol vehicleMotorised small rectangular trolly made of wood and wrought iron ME1 P.B.P.S Track Construction Departmentme 1, trolley, victorian railway, 2'6" gauge, puffing billy, trolly

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

Extract from The Spectator of June 12, 1946: "From the Queensland 'Methodist Times'. Dreams do come true. At any rate, that is what the Rev. Cliff Lanham believes, who after the lapse of several years finds that his early dream of a Flying Patrol for the Inland is now an actuality. The Methodist Inland Mission Board has purchased from the Disposals Commission of the R.A.A.F. a De Haviland Fox Moth Biplane. Indeed, two machines have been bought, but one will be broken up for spare parts. This 'new angel of the air' is fitted with a 130 h.p. engine and possesses a cruising speed of 100 miles per hour. The petrol consumption is only that of a big six-cylinder car—18 miles per gallon. In addition to the pilot there is room for three passengers, and a stretcher is installed whereby urgent cases of sickness or accident can be flown to the nearest hospital. In this machine, Mr Lanham proposes to cover the whole of S. W. Queensland and a portion of the Northern Territory from his headquarters at Mt Isa. It takes little imagination to realise what a boon the 'flying parson' will be to those of the great outback." …. "Before [Mr Lanham] inaugurated the scheme [the idea of a flying parson] he spent his first furlough from inland mission work (and incidentally £60) learning to fly. 'In a month,' he says whimsically, 'I was a pilot of sorts.' Mr Lanham is a son of the Church. His parents were staunch Methodists, and their home offered generous hospitality to mininsters and preachers. His brother, the Rev. Percy Lanham, M.A., died in Libya when on active service as a chaplain. His widowed mother must be proud of her tall, stalwart son, whom the Church now sends forth on his flying mission for the Lord. May he ever be wafted through inland skies on two wings and a prayer." It is of interest to note that although Cliff Lanham's brother, Percy, is listed in the Methodist Church of Australasia's Ministerial Index (9th Edition, Revised to 1961) Cliff Lanham himself is not listed as either active or deceased.Three B&W identical photographs of Lanham standing next to a Methodist Inland Mission bi-plane. Lanham and an unidentified man are holding a stretcher between them with a boy of about 10-11 on it. They seem to be exiting the plane. The original photograph F69-1 is a 110x65 mm Kodak print; the other two are 195x145 mm enlargements. Lanham is wearing a white shirt and grey trousers, the other person is wearing a safari helmet.All three photos identify "Rev. Cliff Lanham" on the back. They seem to have been originally used or intended for use by The Spectator.lanham, cliff, queensland, methodist inland mission, flying parson

This photograph is of the side of the main building of the Gold Battery with workshop at rear (now demolished). Beside building is a hand windlass, along with some old pulleys and various parts. This is one of a series of photographs of the Rutherglen Gold Battery. The battery's purpose was to crush quartz from nearby quartz reefs and extract gold from within. The battery was erected in 1908 and consists of a five-head battery, Wilfrey table, Bergin pan, portable steam engine and shed. The battery was restored in 2011/12 and can be viewed daily between 9.00am and 5.00pm. See website for details.Colour photograph of the side of a corrugated iron building with a smaller building at the left, and a number of pieces of machinery next to the buildinggold battery, gold processing

This photograph is of the back end of the side of the main building of the Gold Battery with workshop at rear (now demolished). Beside building is a hand windlass, along with some old pulleys and various parts. This is one of a series of photographs of the Rutherglen Gold Battery. The battery's purpose was to crush quartz from nearby quartz reefs and extract gold from within. The battery was erected in 1908 and consists of a five-head battery, Wilfrey table, Bergin pan, portable steam engine and shed. The battery was restored in 2011/12 and can be viewed daily between 9.00am and 5.00pm. See website for details.Colour photograph of the side of a corrugated iron building with a smaller building at the left, and a number of pieces of machinery next to the buildinggold battery, gold processing

An illustrates parts catalog produced by Pratt & Whitney for the PT6A-series turboprop engine. pratt & whitney, aero engines, turboprop manual, pt6a-series engine