Wrap reel manufactured at Valley Worsted Mill and possibly used in the laboratory. "Wrap reels were used to check the yarn count in a spinning mill. A set length of yarn was wound off several test bobbins and weighed, if the weight was not the correct amount expected the spinning machines draft could be re calculated and the machine draft wheel ( cog ) changed to achieve the required count". - Greg AldridgeA small hand operated wrap reel. The reel is on a wooden base, the winding mechanism is metal and turned by a wooden handle. There is a metal plaque on the base inscribed MAKERS VWM. A wood and metal yarn feeder has broken off its mount.MAKERS/ VWMtextile machinery textile production weaving, valley worsted mill valley worsted mill, warping machinery, textile machinery, textile production, weaving, wrap reel, skein winder

Long steel shaft half of which is twisted into a corkscrew shape and sharpened to make a hole in wood. The other end has been formed into a round hole so that a handle may be inserted to turn the drill. Used for drilling hole in fence post.rural industry, fencing

Possibly made on-siteof critical significance GALVANIZED METAL BATH. Rectangular shaped bath, with rounded ends, turned rim. Roughly soldered. Consisting of a wood & iron frame with 4 claw feet & plug. Decorative floral motif on upright supports joining to claw feet.bathing

The wood from which the bowl was turned came from the original Lone Pine Tree that stood by the Shrine of Remembrance in Melbourne for many years.A round bowl made from pine wood. Details around the bottom. "The Lone Pine Gallipoli produced seeds which were subsequently planted in Australia. This bowel was made from the wood of one of those trees"

Please find 5 photographs taken by me & my wife Brenda, at Ballarat, on 14 December 1993. Unfortunately, I did not take photographs of the building that housed the exhibit, probably because I thought just how sad and pathetic the entire memorial display looked. It comprised a reconstructed slab hut and nearby a partly-rebuilt fence that represented the hastily-built Eureka Stockade. The signage that detailed the events surrounding the Eureka Stockade was affixed to the hut wall beside the entrance to the interior diorama. In the first photograph, you can see the dark, bare timber colour of the slab wood that held the signage plus (on the left side) one of the numerous holes in the slab walls. This made the display very cold and draughty in its interior. Once inside, you were confronted with an earthen, gravel and leafy floor, which became muddy, after rain, as it was on the day of our visit. The diorama was held in a glass and cement display case. with no lights on. It was dark inside the hut so the diorama was not easy to see unless you inserted a coin into a metal pay-box. Then lights would turn on and a recording of shouting and gunfire (representing the battle noise) would play. I remember the whole experience to be short and underwhelming. To get an idea of the scale of the diorama, you can see Brenda’s elbow & part torso to the left of the photograph labeled “diorama- hut exit”. Once outside the diorama’s slab hut, you could walk across to a partial representation of the stockade’s fortifications, complete with two wagon wheels. This space was also graveled to distinguish it from the rest of the green-lawn park. Finally, you walked up the hill, from the hut and outside display, to visit the old Eureka Stockade monument & cannons. This is still in existence today. Digital photographeureka stockade, sign, diorama, jack ford, brenda ford, memorial

The signage that detailed the events surrounding the Eureka Stockade diaroma was affixed to the hut wall beside the entrance to the interior diorama. In the first photograph, you can see the dark, bare timber colour of the slab wood that held the signage plus (on the left side) one of the numerous holes in the slab walls. This made the display very cold and draughty in its interior. Once inside, you were confronted with an earthen, gravel and leafy floor, which became muddy, after rain, as it was on the day this photograph was taken. The diorama was held in a glass and cement display case. with no lights on. It was dark inside the hut so the diorama was not easy to see unless you inserted a coin into a metal pay-box. Then lights would turn on and a recording of shouting and gunfire (representing the battle noise) would play. The Photographer remembers the whole experience to be short and underwhelming. Once outside the diorama’s slab hut, you could walk across to a partial representation of the stockade’s fortifications, complete with two wagon wheels. This space was also graveled to distinguish it from the rest of the green-lawn park. digital photographeureka stockade, diorama, jack ford, brenda ford, eureka stockade memorial

The signage that detailed the events surrounding the Eureka Stockade diaroma was affixed to the hut wall beside the entrance to the interior diorama. In the first photograph, you can see the dark, bare timber colour of the slab wood that held the signage plus (on the left side) one of the numerous holes in the slab walls. This made the display very cold and draughty in its interior. Once inside, you were confronted with an earthen, gravel and leafy floor, which became muddy, after rain, as it was on the day this photograph was taken. The diorama was held in a glass and cement display case. with no lights on. It was dark inside the hut so the diorama was not easy to see unless you inserted a coin into a metal pay-box. Then lights would turn on and a recording of shouting and gunfire (representing the battle noise) would play. The Photographer remembers the whole experience to be short and underwhelming. Once outside the diorama’s slab hut, you could walk across to a partial representation of the stockade’s fortifications, complete with two wagon wheels. This space was also graveled to distinguish it from the rest of the green-lawn park.digital photographeureka, diorama, 1993, jack ford, brenda ford, eureka monument, memorial

Please find 5 photographs taken by me & my wife Brenda, at Ballarat, on 14 December 1993. Unfortunately, I did not take photographs of the building that housed the exhibit, probably because I thought just how sad and pathetic the entire memorial display looked. It comprised a reconstructed slab hut and nearby a partly-rebuilt fence that represented the hastily-built Eureka Stockade. The signage that detailed the events surrounding the Eureka Stockade was affixed to the hut wall beside the entrance to the interior diorama. In the first photograph, you can see the dark, bare timber colour of the slab wood that held the signage plus (on the left side) one of the numerous holes in the slab walls. This made the display very cold and draughty in its interior. Once inside, you were confronted with an earthen, gravel and leafy floor, which became muddy, after rain, as it was on the day of our visit. The diorama was held in a glass and cement display case. with no lights on. It was dark inside the hut so the diorama was not easy to see unless you inserted a coin into a metal pay-box. Then lights would turn on and a recording of shouting and gunfire (representing the battle noise) would play. I remember the whole experience to be short and underwhelming. To get an idea of the scale of the diorama, you can see Brenda’s elbow & part torso to the left of the photograph labeled “diorama- hut exit”. Once outside the diorama’s slab hut, you could walk across to a partial representation of the stockade’s fortifications, complete with two wagon wheels. This space was also graveled to distinguish it from the rest of the green-lawn park. Finally, you walked up the hill, from the hut and outside display, to visit the old Eureka Stockade monument & cannons. This is still in existence today. digital photographeureka, diorama, 1993, jack ford, brenda ford, eureka monument, memorial, eureka stockade, eureka diorama

This President's chair was used by the Shire of Bulla Presidents/Mayors to sit in at Council meetings pre 1963 in the Sunbury Memorial Hall and possibly at the old Shire of Bulla Council offices in Bulla.Large brown upholstered wood frame President's chair. Small front turned legs. Small padded arm rests. High back padded with seven (7) buttons.A design carved into sides of front arm rests.sunbury, shire of bulla, shire presidents, memorial hall, george evans collection

A weapon issued to Ghurka servicement. Often purchased as a souvenir by returning servicemen from Southeast Asia and later donated as a Mess decoration.Representative of souvenirs from WWII.Large knife with inward turned blade traditionally carried by Gurkha soldiers. Sheath is wood covered by leather. Includes two much smaller knives which fit into the top of the sheath.Blade is engraved with decoration.kukri, gurkha

In 1960 seventy-four commandos from 2 Commando Company left Point Lonsdale at 6pm on February 17 to cross The Rip in an exercise raid on the Portsea officer school. Shortly after departing, a strong tide caught the raiding party and pushed them out to sea through The Rip, where 10-metre waves capsized many of the kayaks and amphibious vehicles. Many of the men were picked up by larger rescue boats, only to be overturned once again in the heavy seas. Warrant Officer George Drakopolous and the driver of his amphibious DUKW, Private Eddie Meyer, both drowned as their vehicle sank. Eight of the commandos were rescued in Bass Strait after being picked up by an Italian ship, the Toscana. Commando Roger Wood helped others board the Toscana safely but was washed off a rope ladder by a monster wave and into the sea. His body was never found. It remains one of Australia's least-known peacetime military tragedies.One of the later disasters around the Rip between Points Nepean and Lonsdale. The 'Queenscliffe' lifeboat turned out to search for survivors without success Paddles from a Mk3 foldaboat used in ill fated commando training exercise in 1960the rip disaster, kayaks, oars

Kaweka Reserve is a a small reserve of approximately 8ha. The land was donated to the Castlemaine City to be a wildflower Reserve. A management committee was formed in 1966. The committee is still managing the park. Vicroads Edition 6: Map 59E2, 628 H4 Location. Turner St, Castlemaine. From the Castlemaine Post Office, drive north (towards Bendigo) and turn right along Turner Street to the park entrance. What to do: walk along some of the tracks through the park follow the nature trail bird watch have a picnic at the picnic tables. RUSH Dam is a basic free camping area sits alongside Rush Dam in the Greater Bendigo National Park, featuring a single picnic table and wood fire barbecue.Peter Ellis Collection: Seventeen slides of Kaweka Wildflower Reserve, Castlemaine, Lightning Hill Lookout Bendigo, One Tree Hill Lookout Tower Bendigo. Also the Rush Dam free camping area at Kamarooka. Also a slide of an unknown group having a meal or day out; perhaps also a working bee. In addition there are two slides of a house - location not specified; and a working bee clearing along a pipeline at Big Hill. Peter was a chemistry lecturer at the Bendigo Institute of technology.history, bendigo, peter ellis collection, whipstick bendigo, bendigo state forests, kaweka wildflower reserve castlemaine, one tree hill lookout bendigo, lightning hill lookout bendigo, kamarooka, rush dam kamarooka, greater bendigo national park

Application for Permission to Publish or reproduce material, dated 7/5/07. Permission was sought to use a wood engraving of a Masquerade Ball given by the German Turn Verein as fill in art in a publication titled The Waltz, The Polka and All Kinds Dance Music, publisher FSDV. The wood carving was in the 'Illustrated Australian News' 24/8/1881. Included is a letter from (Dr.) Dianne Reilly, La Trobe Librarian, granting permission to use material from the Library's collections in a Book, providing acknowledgement appears adjacent to the image. Dated 2/7/2007.State Library Victoriacommunication, postal, letters, peter ellis collection, state library of victoria, madeleine say, dr dianne reilly, la trobe

Wooden inkwell with bakelite insert made from Australian mulga wood with top turned in steps.Genuine Australian Mulgadomestic equipment, writing equipment, ink well

"In 1839 John Dight purchased Melbourne block 88, which included 26 acres of land along the Yarra River for £481 at the Port Phillip land sales held in Sydney. Dight was already in the business of flour milling and had a mill near Campbell Town in New South Wales called ‘Ceres’. In April 1840, he notified his customers through The Sydney Herald that he was leaving to go to Port Phillip. The first steam powered flour mill was constructed in Melbourne in 1841. Dight built his water powered mill, soon after, from bricks bought over from Tasmania. Dight used the river to power his mill: Water flowed along an inlet channel to turn an undershot water wheel. In order to regulate flow or to ensure flow for times when river levels were low, Dight constructed a rough stone weir." (Melbourne Water)Dights Mill. Reproduction of a book plate from an original wood engraving, showing Dights Mill and Falls on the River Yarra. The image was originally published in Sands & Kenny, Melbourne & Sydney.Annotation on reverse: "Dights Flour".dights mill, yarra river

Bedside table with round top, made of timber. 3 legged, round pedestal. Spiral turned and carved stem. Varnished.furniture, domestic, bedside, table, wood, varnished, turned

Vic WOOD (1939 - 02 October 2020) Born Melbourne, Victoria Vic Wood was an internationally renowned artist, craftsman and teacher from the 1970s. He studied gold and silversmithing, woodturning and cabinet making at Melbourne Teachers' College and Royal Melbourne Institute of Technology. He was a skilled woodturner who, as a lecturer at Melbourne College of Advanced Education, taught a generation of woodworkers. Best known as a master wood-turner, Vic Wood retired from lecturing in 1983 to become a full-time woodturner. He was a sought after demonstrator and presenter for all kinds of local and international events. His teaching philosophy was simple: ‘share everything, have nothing to hide, and have no secrets; for ultimately it is in giving that you receive’. Vic Wood was a foundation member and inaugural president of the Victorian Woodworkers Association (VWA). In 1923 the Victorian Woodworkers Association announced the establishment of an annual Vic Wood Scholarship. he intent of the award is to promote excellence in woodwork and to engender inclusive and supportive woodworking networks. This item is part of the Federation University Art Collection. The Art Collection features over 2000 works and was listed as a 'Ballarat Treasure' in 2007.Large lathe-turned sculptural relief. art, artwork, vic wood, wood, woodwork, sculptural relief

The 'Melbourne District Nursing Society After Care Home' was built by MDNS in 1926 and the name changed from 'Care' to 'Hospital' in 1934. It was located at 45 Victoria Parade, Collingwood. This photograph is taken three years after Miss Dorothy Tupper was appointed Matron of the District Nursing Division of the Society in 1941. The Sisters in this Division worked in the community giving nursing care to people in their own homes.From its foundation in 1885 the Melbourne District Nursing Society (MDNS, were instrumental in giving care to their patients, and to assist them if they had financial problems or resided in poor living conditions. Miss Dorothy Tupper, who as a Trained nurse, had undertaken a course in hospital housekeeping at London Prince of Wales Hospital, was contacted by MDNS in 1939 and, possessing both business and humanitarian qualities, was asked to organize their newly established Social Service Department. As the MDNS Social Service Sister, she assessed the living conditions in patient's homes. She continued in this role until being appointed Matron of the Society's District Nursing division in 1941. Matron Dorothy Tupper announced her retirement in December 1962. As Matron for 22 years she played a major role in the employment and management of an ever increasing nursing workforce as well as help oversee the expansion of the service. Matron Tupper was known for her keen sense of duty, her high professional standards and never-failing concern for patients. The photograph was taken by Sun Newspaper photographer and appeared in an article about the MDNS in September 1944Black and white photograph showing Melbourne District Nursing Society (MDNS) Matron, Dorothy Tupper, standing side on, and to the left, of three District Trained nurses (Sisters) who are seated in the grounds of the After-Care Hospital. Matron Tupper is wearing a light coloured uniform which has a belt and a centre box pleat on the lower part of the skirt; a grey brimmed hat with a darker grey hat band sits over her short dark hair. She is looking down at the first Sister on the seat who is looking up at her. The Sisters at either end of the seat are wearing dark grey double breasted coats with lapels; the collars of their light colour uniforms can be seen. Both are wearing grey brimmed hats over their short dark hair. The Sister at the far end is wearing glasses and the Sister near Matron Tupper is holding a book. The centre Sister has shoulder length dark hair and is wearing a light coloured long sleeve uniform. She is also holding a book. Both these Sisters are looking toward Matron Tupper. The seat is made of wood and is against the concrete veranda of the building behind. Scrolled metal lace work is directly behind them with a round thin concrete post to the left of Matron Tupper and the other end of the lace work is fixed to the concrete square corner columns. One turns to the right and the concrete wall of the veranda attached can be seen running in front of part of the brick wall of the building.after- care hospital, melbourne district nursing society, mdns, nurses, matron, mdns social service department, rdns, royal district nursing service, matron dorothy tupper

From home of Mervyn Sebire, 2nd son of Thomas and Linda Sebire.A dark brown cedar wood chest of drawers, with four legs. It has four small drawers, one square one in the middle and three larger drawers at the bottom and all have a keyhole. All have a large round turned knob to hold to open them.chest of drawers, cabinets, storage and display furniture

The Billiard Room and South wing were completed in 1914, built by recommendation of the Lesee John Newton and the Government Tourist Officer and Supervising officer of the Government Chalet, James Boyce... "Boyce was present at the Chalet on 14 March to witness the completion of the new wing's foundations ...when he returned in June he found the wing approaching completion and that '... the billiard table was expected to reach the Chalet during the week'. The table possibly came second-hand from the Oriental Hotel, Bright. When visiting in March, Boyce had heard from a Mr Tewksbury 'that he is disposing of those at the Oriental Hotel so that if the Public Works Department is going to provide the table for the Chalet it might be possible to pick one up cheap from the Hotel'. It's reasonable that the Chalet did acquire one of the second-hand tables in 1914 and, and changed over to a new model in the 1930s. Three billiard tables remain in the Chalet Billiard Room today; one full sized table and two smaller tables, one perhaps a pool table. The full-sized table was made by the well-known billiard table manufacturers Alcock, Thomson & Taylor, who adopted this name when they merged their billiard businesses in January 1930. Henry Upton Alcock had initially established the business in Fitzroy in the mid-1850's and the table at the Chalet resembles the 'Squatter's Favourite' model that Alcock first produced in the nineteenth century from Australian timbers. this style of table was installed in Melbourne's Parliament buildings, several prestigious clubs as well as hotels and houses."(Pg 13-14. Historica)Listed in Appendix A.1 Furnishings. - Billiard Room. Draft Inventory of significant Collection Items. (Pg 162 Historica, 2011)1. Full size billiard table made of dark wood with eight turned legs. Green blaize covered table surface. 2.Wooden triangle to enclose balls. 3.balls(16) .4 Wooden backed bristle brush with VR stamp. 5. Billiard scorer with Alcock & Taylor, Pty, Ltd. 6. framed billiard rules. 7. Pool balls & cue rest. .8Plus 1x revised rules of pool framed behind glass.(stored in area 23) 1 x original cue rest.Alcock, Thomson & Taylor.

Bluthner piano dated 1889 (patent no. 32310). PWD engraved imprint to wood. "The Bluthner grand piano came second-hand to the Chalet in 1920 when it was obtained by lessee, Hilda Samsing. This high quality German piano, which stands out as an item of individual significance, is now one of the oldest furnishings in the Chalet. When it was acquired in 1920, the Chalet already had a Beale brand upright piano which had been at the Chalet from the earliest days." (Pg. 77 Historica. 2011) 'A photograph taken of the Music Room (also known as the Drawing Room) between 1920 and 1924, when Hilda Samsing was lessee is one of the earliest known photographs of the Chalet's lounge areas. Published in the undated promotional booklet, Victoria's Wonderland Mount Buffalo, it shows 'A corner of the music room'... On the right, is the Chalet's second piano, which was purchased second-hand in 1920 from Gardner & Lang in Swanston Street, Melbourne. This impressive grand piano of walnut wood still stands in the Chalets Music Room. It was made in the world-famous factory of Julius Bluthner, in Leipzig, Germany, which has made Bluthner pianos since 1853 for numerous royals, composers, conductors, artists, authors and performers including Brahms, Mahler, Bartok, Debussy, Wagner, Strauss, Tchaikovsky and Rachmaninoff. The present stool is not part of the ensemble." ( Pg. 42. Historica )Listed in Draft Inventory of Significant Collection Items. Appendix A.1. Furnishings, Lounges and Hallways (Pg 163. Historica"Bluthner" grand piano made from walnut wood with accomanying wooden stool.(not matching). Piano features three large turned and carved legs on brass castors. Pedals on piano are solid brass, surrounded by carved and turned wooden pedal stand. Stool seat slants towards piano and two plain stretchers support four curved legs. Has 'PWD' stamped on it. PWD engraved imprint to wood.

Used as pattern to cast crown wheel of drive on water wheel. Actual drive has since been sold, only mold remainsCircular wooden pattern, raised centre circular area surrounded by four wide, flat spokes at regular intervals (the interim spaces being cut out with rounded corners) which are in turn surrounded by a rim which tapers back from the centre of the piece and has fixed to it regularly interleaved slats. Slats of protruding oblongs tapered from attachment to top and also central end to outer point. Light coloured wood 1 & 2 are Broken off pieces of back.

This table was found in the shed and restored in the 1990's by lightstation staff. The late nineteenth century cedar table has turned legs, a front drawer with brass knob pull (this may not be original). The wood has lost its original finish. Despite this, it has first level contributory significance for its historic value as an original furnishing that has remained at the lightstation since the nineteenth century.It has first level contributory significance for its historic value as an original furnishing that has remained at the lightstation since the nineteenth century.Australian cedar table with turned legs and front drawer with brass keyhole and wooden knob. Unpainted.

Cyril Smith was a popular figure amongst his contemporaries and this has been recognised by the plaque from those who new him. Appreciation of fellow Legatees to a comrade. The plaque has sentimental value, the words, the time and effort to make it by fellow Legatees shows the high regard in which Cyril was held. Caricature and signatures on a piece of 3 ply wood, front varnished, rectangular shape. Hole drilled top centre.Handwritten message in black ink "Our Cyril.,Heres from every cobber who wore the old chapeau". A caricature of Cyril Smith engraved (burnt) into the timber. Signatures of many Legatees, signed in ink. Reverse side, "Cyril - From all old cobbers of Melbourne Legacy Club with happy memories Legacy. 1938." Handwritten in black ink "Mrs Cyril Smith gave me this plaque which I in turn now pass onto Legacy Comradeship for safekeeping. Frank Doolan June 1962"comradeship, cyril smith

This tenon saw was used in the making of components for the ship model Sovereign of the Seas. Tenon saws are often used for making dovetail joints. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This tenon saw is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This tenon saw was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Tenon Saw. Hand saw with small-toothed metal blade set into a slotted brass back, attached to a round brass fitting in the light coloured, turned wooden handle. Top on handle is marked with seven concentric rings scored into the wood. On top of blade is maker’s name “AVIA” within oval ring. This tenon saw is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”."Avia" within oval ring.flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, saw, wood cutting tool, tenon saw, avia steel and tool company limited, carpenter's tool, tool, sovereign of the sea, ship model, hobby, ship model tool

The British Arts and Crafts Movement was a major influence on handcrafts made by the Leviny women at Buda. This Movement spread knowledge of craft techniques in the decorative arts and encouraged women to partake in fields that had traditionally been the domain of men, such as metalcraft and woodwork. The Leviny women studied art, design and craft techniques at the Castlemaine School of Mines from the 1890s to the early 1900s and this boot stool, hand-carved by Gertrude, is an example of the influence of the Arts and Crafts Movement on her decorative art. See: Zilles, Lauretta (2010), Buda and the Leviny Family, Castlemaine: Buda Historic Home & Garden Inc.This is a rare example of a unique hand-carved boot stool made in Australia by Gertrude Leviny in the British Arts and Crafts Movement style at the turn of the twentieth century.Timber boot stool, hand-carved by Gertrude Leviny. Made using the 'chip carving' technique, with dragon heads on upright at one end, and plant design in relief on the seat. Timber finish has a blackened effect.'K/40' (Old Registration Number)gertrude leviny, wood carving, arts and crafts movement, buda, castlemaine, dragon's heads, c1900, domestic furniture, castlemaine school of mines

This is a teacher's desk which came from Woodford State School. The school began in 1854 in a private dwelling with a new building constructed in 1874. The school still operates today.This is a very fine example of an early 20th century school teacher's desk. As it comes from one of the earliest schools in the district, it is of considerable significance.This is a wooden desk, now varnished, with a lift up, slanted lid with brass hinges and a brass key hole. On the top right hand side is a brass insert with a porcelain ink well. The desk has four turned legs with end struts. The desk lid may be made of pine but the rest of the desk seems to be made of a different wood. There are signs of old borer on the left hand front and the curved part on that side is missing.woodford state school, teachers desk, wooden teachers desk

Prior to carrying out a detailed condition report of the cetacean skeletons, it is useful to have an understanding of the materials we are likely to encounter, in terms of structure and chemistry. This entry invites you to join in learning about the composition of whale bone and oil. Whale bone (Cetacean) bone is comprised of a composite structure of both an inorganic matrix of mainly hydroxylapatite (a calcium phosphate mineral), providing strength and rigidity, as well as an organic protein ‘scaffolding’ of mainly collagen, facilitating growth and repair (O’Connor 2008, CCI 2010). Collagen is also the structural protein component in cartilage between the whale vertebrae and attached to the fins of both the Killer Whale and the Dolphin. Relative proportions in the bone composition (affecting density), are linked with the feeding habits and mechanical stresses typically endured by bones of particular whale types. A Sperm Whale (Physeter macrocephalus Linnaeus, 1758) skeleton (toothed) thus has a higher mineral value (~67%) than a Fin Whale (Balaenoptera physalus Linnaeus, 1758) (baleen) (~60%) (Turner Walker 2012). The internal structure of bone can be divided into compact and cancellous bone. In whales, load-bearing structures such as mandibles and upper limb bones (e.g. humerus, sternum) are largely composed of compact bone (Turner Walker 2012). This consists of lamella concentrically deposited around the longitudinal axis and is permeated by fluid carrying channels (O’Connor 2008). Cancellous (spongy) bone, with a highly porous angular network of trabeculae, is less stiff and thus found in whale ribs and vertebrae (Turner Walker 2012). Whale oil Whales not only carry a thick layer of fat (blubber) in the soft tissue of their body for heat insulation and as a food store while they are alive, but also hold large oil (lipid) reserves in their porous bones. Following maceration of the whale skeleton after death to remove the soft tissue, the bones retain a high lipid content (Higgs et. al 2010). Particularly bones with a spongy (porous) structure have a high capacity to hold oil-rich marrow. Comparative data of various whale species suggests the skull, particularly the cranium and mandible bones are particularly oil rich. Along the vertebral column, the lipid content is reduced, particularly in the thoracic vertebrae (~10-25%), yet greatly increases from the lumbar to the caudal vertebrae (~40-55%). The chest area (scapula, sternum and ribs) show a mid-range lipid content (~15-30%), with vertically orientated ribs being more heavily soaked lower down (Turner Walker 2012, Higgs et. al 2010). Whale oil is largely composed of triglycerides (molecules of fatty acids attached to a glycerol molecule). In Arctic whales a higher proportion of unsaturated, versus saturated fatty acids make up the lipid. Unsaturated fatty acids (with double or triple carbon bonds causing chain kinks, preventing close packing (solidifying) of molecules), are more likely to be liquid (oil), versus solid (fat) at room temperature (Smith and March 2007). Objects Made From the Whaling Industry We all know that men set forth in sailing ships and risked their lives to harpoon whales on the open seas throughout the 1800s. And while Moby Dick and other tales have made whaling stories immortal, people today generally don't appreciate that the whalers were part of a well-organized industry. The ships that set out from ports in New England roamed as far as the Pacific in hunt of specific species of whales. Adventure may have been the draw for some whalers, but for the captains who owned whaling ships, and the investors which financed voyages, there was a considerable monetary payoff. The gigantic carcasses of whales were chopped and boiled down and turned into products such as the fine oil needed to lubricate increasing advanced machine tools. And beyond the oil derived from whales, even their bones, in an era before the invention of plastic, was used to make a wide variety of consumer goods. In short, whales were a valuable natural resource the same as wood, minerals, or petroleum we now pump from the ground. Oil From Whale’s Blubber Oil was the main product sought from whales, and it was used to lubricate machinery and to provide illumination by burning it in lamps. When a whale was killed, it was towed to the ship and its blubber, the thick insulating fat under its skin, would be peeled and cut from its carcass in a process known as “flensing.” The blubber was minced into chunks and boiled in large vats on board the whaling ship, producing oil. The oil taken from whale blubber was packaged in casks and transported back to the whaling ship’s home port (such as New Bedford, Massachusetts, the busiest American whaling port in the mid-1800s). From the ports it would be sold and transported across the country and would find its way into a huge variety of products. Whale oil, in addition to be used for lubrication and illumination, was also used to manufacture soaps, paint, and varnish. Whale oil was also utilized in some processes used to manufacture textiles and rope. Spermaceti, a Highly Regarded Oil A peculiar oil found in the head of the sperm whale, spermaceti, was highly prized. The oil was waxy, and was commonly used in making candles. In fact, candles made of spermaceti were considered the best in the world, producing a bright clear flame without an excess of smoke. Spermaceti was also used, distilled in liquid form, as an oil to fuel lamps. The main American whaling port, New Bedford, Massachusetts, was thus known as "The City That Lit the World." When John Adams was the ambassador to Great Britain before serving as president he recorded in his diary a conversation about spermaceti he had with the British Prime Minister William Pitt. Adams, keen to promote the New England whaling industry, was trying to convince the British to import spermaceti sold by American whalers, which the British could use to fuel street lamps. The British were not interested. In his diary, Adams wrote that he told Pitt, “the fat of the spermaceti whale gives the clearest and most beautiful flame of any substance that is known in nature, and we are surprised you prefer darkness, and consequent robberies, burglaries, and murders in your streets to receiving as a remittance our spermaceti oil.” Despite the failed sales pitch John Adams made in the late 1700s, the American whaling industry boomed in the early to mid-1800s. And spermaceti was a major component of that success. Spermaceti could be refined into a lubricant that was ideal for precision machinery. The machine tools that made the growth of industry possible in the United States were lubricated, and essentially made possible, by oil derived from spermaceti. Baleen, or "Whalebone" The bones and teeth of various species of whales were used in a number of products, many of them common implements in a 19th century household. Whales are said to have produced “the plastic of the 1800s.” The "bone" of the whale which was most commonly used wasn’t technically a bone, it was baleen, a hard material arrayed in large plates, like gigantic combs, in the mouths of some species of whales. The purpose of the baleen is to act as a sieve, catching tiny organisms in sea water, which the whale consumes as food. As baleen was tough yet flexible, it could be used in a number of practical applications. And it became commonly known as "whalebone." Perhaps the most common use of whalebone was in the manufacture of corsets, which fashionable ladies in the 1800s wore to compress their waistlines. One typical corset advertisement from the 1800s proudly proclaims, “Real Whalebone Only Used.” Whalebone was also used for collar stays, buggy whips, and toys. Its remarkable flexibility even caused it to be used as the springs in early typewriters. The comparison to plastic is apt. Think of common items which today might be made of plastic, and it's likely that similar items in the 1800s would have been made of whalebone. Baleen whales do not have teeth. But the teeth of other whales, such as the sperm whale, would be used as ivory in such products as chess pieces, piano keys, or the handles of walking sticks. Pieces of scrimshaw, or carved whale's teeth, would probably be the best remembered use of whale's teeth. However, the carved teeth were created to pass the time on whaling voyages and were never a mass production item. Their relative rarity, of course, is why genuine pieces of 19th century scrimshaw are considered to be valuable collectibles today. Reference: McNamara, Robert. "Objects Made From the Whaling Industry." ThoughtCo, Jul. 31, 2021, thoughtco.com/products-produced-from-whales-1774070.Whale bone during the 17th, 18th, 19th and early 20th centuries was an important industry providing an important commodity. Whales from these times provided everything from lighting & machine oils to using the animal's bones for use in corsets, collar stays, buggy whips, and many other everyday items then in use.Whale rib bone with advanced stage of calcification as indicated by brittleness. None.warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, whale bones, whale skeleton, whales, whale bone, corsets, toys, whips, whaleling industry, maritime fishing, whalebone

Example of wood work and woodgraining popular in 1901 when the room was decorated. Mantel and mantel surround of pine turned and carved with this central panel beneath the mantel shelf all woodgrained in an oak finish.Fireplace surround featuring under-mantel panel with decorative carved acanthus leaves in urn with a rose at each extremity all in a woodgrain finish.woodgrain, decoration, mantel, oak finish, pine

Originally Wellers Hotel, it was constructed by Edward Weller in 1872. Following his death in 1883 it was taken over by his widow, Mary Weller. The hotel was delicensed in 1909 and converted to a private residence. Around 1920 William Pitman bought the property, succeeded by his son Vernon who coined the term Pittman's Corner. Vernon and Isabel Pitman owned the house form 1945-1973. Following Vernon's death, Isabel remained there till her death in 1983. The property was converted to a restaurant in 1984 by owners Robert and Kath Hendry who undertook extensive renovations in 1988. Shawn and Stephanie Wolfe purchased the property from the Hendrys in 2003 and introduced live entertainment with many famous bands and entertainers from the 1960s, 1970s and 1980s performing there, including James Reyne, Daryl Barithwaite, Brian Cadd and Billy Thorpe. In 2014 the Wolfe's sold the property and the entire contents were sold at auction. New (local ) owners Gregory Anderson, Craig Jones and Steve Gist refurbished the property and relaunched it as Fondata 1872 in 2017. Covered under Heritage Overlay, Nillumbik Planning Scheme. Published: Nillumbik Now and Then /​ Marguerite Marshall 2008; photographs Alan King with Marguerite Marshall.; p87 A low-lying brick building at a turn on the main road, on the way to Kangaroo Ground, was once a welcome resting place for travellers. In the late 19th century Weller’s Pub, as it was called then, provided a store and an overnight stopping place and changing post for Cobb & Co coaches. The coaches were bound for the Caledonia Goldfields, near Queenstown (now St Andrews) and the Woods Point gold mines.1 Builder Edward Weller constructed the hotel and store on three acres (1.2 ha) in 1872 and after he died in 1883, his widow, Mary, continued to run the hotel, which was delicensed in 1909. This was not the first enterprise Weller ran in the district. In about 1866, he came to Kangaroo Ground and rented a general store and nine acres (3.6 ha) of land. The store, opposite the present school, was on the site of the present store and Weller also acted as the postmaster there. Mrs Weller was born in Scotland in 1841 and came to Victoria with her parents in about 1852. After two years in Melbourne the family moved to the Caledonia Goldfields where they remained for several years during which time she married Weller. The couple subsequently had five sons and five daughters. Weller’s Pub was made of handmade bricks fired from clay dug on the property. The pub must have been a haven on hot days with its 40cm thick walls throughout. One quaint reminder of its early use is that every room except the dining room has an outside door. Inside, the pub was converted to a home with extra doors connecting the inside rooms. There is no trace of the original bar room in the present dining room, where the steps leading to the cellar were bricked in. An unusual feature is the pressed metal which lines the ceilings, yet with moulding and white paint, looks like plaster. The main road once passed the back of the building and wound up to the top of the hill through a cutting. This steep hill was known to the bullock drivers in the early days, as Salvation Hill, because they were always very glad to reach its peak. After the hotel was delicensed it was converted to a private residence and extensive renovations were made, changing much of its design from a Victorian to an Edwardian style.2 Between 1912 and 1915, Gordon Cameron, a Cobb & Co coach driver and his wife rented the former hotel. Mr Cameron was related to the parliamentarian Ewen Cameron of Pigeon Bank, Kangaroo Ground, and his wife was related to Albert Pepper who owned Pigeon Bank from 1916 to 1919, when Gordon Cameron bought it. About 1920 William Pitman bought the property, which in turn was owned by his son, Vernon, who coined the name Pitman’s Corner. He and his wife Isabel owned the house from 1945 to 1973. Then as a widow Isabel Pitman lived there until her death in 1983.3 In 1984 the property was converted to a restaurant by owners P A Tribe, a barrister, his wife Sharon, and Robert and Kath Hendry. Extensive renovations maximised the splendid views of the Dandenong Ranges and the Yarra Valley.This collection of almost 130 photos about places and people within the Shire of Nillumbik, an urban and rural municipality in Melbourne's north, contributes to an understanding of the history of the Shire. Published in 2008 immediately prior to the Black Saturday bushfires of February 7, 2009, it documents sites that were impacted, and in some cases destroyed by the fires. It includes photographs taken especially for the publication, creating a unique time capsule representing the Shire in the early 21st century. It remains the most recent comprehenesive publication devoted to the Shire's history connecting local residents to the past. nillumbik now and then (marshall-king) collection, eltham-yarra glen road, fondata 1872, kangaroo ground, wellers restaurant, billy thorpe, brian cadd, craig jones, daryl barithwaite, edward weller, gregory anderson, hotels, james reyne, kath hendry, mary weller, restaurants, robert hendry, shawn wolfe, stephanie wolfe, steve gist