It is likely that this object belonged to Dr Giles.Chevalier Jackson medium size steel made laryngoscope. Hexagonal shape design on handle and arm blade with a thumb support at the handle angle, missing the bulb light and all the system to support it. Deep scratches over the top and under blade with presence of dust marks over the handle, arm and inside the blade canal. Also has a grey paint mark over the top blade area. No stamped inscriptions are present just a label attached with a possible owner's name and a reference code to the museum old catalog.Attached label hand written inscription, Giles / S 4. 13chavalier jackson, laryngoscope, stainless steel

Used by the Mah Meri people, Kuala Langat, Selangor (Malaysia), 1936. While Malaysian, this blow-gun is analogous to that used by Indigenous groups from South America with curare. The gun is of bamboo, with a highly polished inner tube of the same. The darts are reeds, made directional by knobs of a tudor wood, with poison made from the ipoh tree and the Strychnos vine The blowpipe examined in this report consists of a long bamboo tube with engraved floral motifs on the outside and a second bamboo tube inside. The mouthpiece is attached to the inner tube and the whole piece can be removed from the outer casing. There is a quiver, filled with darts, a small poisons receptacle, and a single dart and hollow bamboo tube, stored outside the quiver. The objects were donated as a whole to the museum in 1948 by Dr Thomas Edward Marshall. The engravings on the outer case originate from the Mah Meri community in Kuala Langat, Selangor, Malaysia. The floral ‘motif is of a vine with small incisions to reflect the properties/identity of the plant (poisonous/harmful)’. These motifs are generally handed down through the generations and can be used for kinship identification. They are also believed to enhance the performance of the blowpipe. The outer casing is made up of several pieces of bamboo fused together. Broken or damaged blowpipes were not discarded. Broken sections of a pipe could be removed and replaced as required, and the observably different bamboo sections suggest this has taken place at some point. Sap from the perah tree is used to seal or glue the pieces together and the glue is reversible by heating. The Mah Meri created a poison from the ipoh tree for use in hunting. The poison acted swiftly to kill the animal and did not result in secondary poisoning. The way in which the Mah Meri hunted is analogous with other blowpipe hunting practices elsewhere in the world. Blowpipe hunting practices represent a starting point for the introduction of standardised muscle relaxants into surgery during the 20th Century. In parts of South America, plant poisons were used to tip the darts and kill prey. These poisons are known as curare. The crucial ingredient in curare was Chondrodendron tomentosum root. Raw curare formed the basis for Intocostrin, the first standardised, mass produced muscle relaxant. The introduction of muscle relaxants dramatically changed surgery, allowing for more precise surgery and better patient outcomes. Bamboo blowpipes can be found in many museum and heritage collections, particularly those with strong colonial origins or influence. Blowpipes from Borneo seem to be well represented, along with those from Guyana. Blowpipes from Malaysia appear to be less common. More research is required to establish the rarity or representativeness of the blowpipe. Ownership of the blowpipe can be traced back from the museum to Dr Thomas Marshall. It has also been established the blowpipe’s point of origin is among the Mah Meri people of Kuala Langat, near Kuala Lumpur. There is no information regarding the way in which Marshall came into possession of the blowpipe. Provenance cannot be fully established. Despite these difficulties, the blowpipe represents a full set of hunting implements. It is accompanied by a quiver, also decorated with a floral motif, a set of bamboo darts, and a poison receptacle. The quiver also has a waist strap which enabled the owner to strap it to themselves, preventing its loss while hunting. Each object within the set is in good condition, although the inner tubing is beginning to split lengthwise and should not be removed from its outer casing. While the blowpipe and accompanying objects are not of South American origin, the techniques and poisons used are analogous and this object has high interpretative capacity. Hollow bamboo blowpipe with mouthpiece at one end. Two different types of organic fibre have been used at difference points along the shaft to secure different segments of the blowpipe. The item consists of two tubes a thin and unpolished inner tube that has degraded and can no longer be removed, and a polished and decorated outer casing. The outer casing is made up of different sections of polished bamboo, some pieces have developed a deep red hue which is likely the result of prolonged polishing and regular heating over many years, other sections are a lighter yellow indicating that they are newer pieces of bamboo. The entire outer tube is covered in a varied sequence of genomic patterns. The exact meaning of these patterns is unknown however they are passed down through family lineage, the exact family of origin is unknown. Connected to the mouthpiece if it is removed from the inner casing is a piece of cloth with the numbers 2241 written in black ink, their purpose is unknown.curare, malaysia, bamboo

This beaker (tumbler) was presented to the Faculty in 1977 by Professor Arthur Bull, as a token of esteem and friendship, from the Faculty of Anaesthetists College of Medicine of South Africa. It was in this year that Professor Bull was also awarded an honorary fellowship from ANZCA. Professor Arthur Barclay Bull was a pioneer of South African Anaesthesia, having played a major role in the specialty and research in anaesthesia from 1954. One of his achievements include the use of prolonged curarisation and IPPV for treating tetanus. In 1965 - 1967 the Taurus Blood Warmer was developed - named after Professor Bull - to prevent hypothermia after major blood transfusion. Not only was Professor Bull the presenter of this beaker, but also its maker. It is hand wrought from sterling silver recovered from discarded tracheostomy tubes. The maker has hallmarked the beaker with the initials A B. Hand wrought sterling silver beaker made from the silver recovered from discarded tracheostomy tubes.To / The Faculty of Anaesthetists / R.A.C.S. / from / The Faculty of Anaesthetists / C.M. of S.A. / 1977 [hallmark in maker's logo] A Btracheostomy, taurus blood warmer, the college of medicine of south africa, faracs

Dr John Hains, presented these two shakers to Dr Neville Davis, President of ANZCA (1995 to 1996). Dr Hains expressed in his letter to Dr. Davis, how these two shakers are made from a red cedar branch which had fallen on his property in Queensland. A pair of hand crafted red cedar salt and pepper shakers, each with a thin gold band above the base.dr john hains, red cedar, hand crafted

This vase was gifted to the Faculty by Dr Walter Wyndham Biggs upon his retirement from the Faculty Board in 1981. Dr Biggs was the first flying anaesthetist of the Flying Surgeon Service based at Longreach in central Queensland. The vase is hand painted by Dr Biggs mother, Bessie Biggs. The manufacturer of the vase, Furstenberg, is one of oldest and most renowned porcelain makers in Europe since 1747. Made in West Germany, the makers mark is found at the base of the vase marked with a blue under glaze symbol of a crown, script F and a number 9. Porcelain vase of bulbous form and narrow neck with gold trim on lip. Black and white hand painted scene of flying geese above a body of water surrounded by reeds.[hand written on base in black ink] Handpainted / by / Bessie Biggs / 1981 [embossed on base] 7405/30 [Blue under-glaze on base] symbol of crown / cursive script F / 9 / FURSTENBERG / SEIT 1747 / WEST GERMANY [Artist signature on painted surface] B BIGGSdr walter biggs, furstenberg, porcelain

Between 1867 and 1920, anaesthesia for dental operations was often maintained by blowing the vapour of ether or chloroform into the patients' oral or nasal pharynx. Junker's inhalers are a "blow over" device used with a hand-held bellows to bubble air through liquid chloroform and to the patient. It was initially intended for use with bichloride of methylene, a mixture of chloroform and methyl alcohol. Ferdinand Ethelbert Junker introduced his inhaler in 1867 as appointed physician to Samaritan Free Hospital for Women (although it didn't have that name until c.1904). Glass jar with liquid measure markers etched onto. The jar has a metal lid, with a metal tube descending into the jar. Two metal tubes are protuding out of the top of the lid, and each has a small section of rubber tubing attached. There is also a metal hook, used to attached the jar to the physicians (anaesthetist's) lapel.Stamped into frame of metal lid: LONDON MADEjunker, blow over, chloroform, samaritan free hospital for women

Standard issue Army wrist watch, commonly called a "Mickey Mouse" watch. This item was specifically made for Australian military use in 1970. A silver metal wrist watch with a glass cover over a round black face with white numbers for both 24 and 12 hour markings. The hands and 5-minute marks glow in the dark. Watch has wind up motion. Army issue green nylon band has a black clasp.Back: Watch. Wrist general purpose. MIL-W-46374A HAMILTON fsn6645-00-952-3767 Armymilitary issue, watch, 1200hr 2400hr watch, wrist watch, vietnam

Long term loan from Neurological Society of Australasia Museum of Neurosurgical Instruments,South Australia. Catalogue with Historical Commentaries Second Edition January 2006 Copy located at RACS MuseumTrumble's Skull Plough or craniotome devised by Hugh Trumble (1864-1962 ) CRANIOTOME. This craniotome was designed by Hugh Trumble (1894-1962) of the Alfred Hospital, Melbourne, one of the eight founders of the Neurosurgical Society of Australasia. It was a modification of an earlier instrument, similar in principle but less versatile, designed by Sir Henry Souttar(l875 - 1964), a very inventive surgeon who worked in the London Hospital. Souttar also used a motor-powered circular saw when necessary. He cut very large circular bone flaps, exposing the occipital lobes and posterior fossa in a few minutes. Trumble reported the use of this craniotome as "an expeditious method of cutting bone flaps" and in the designer's hands this claim was certainly justified. To use the crauiotome, it was necessary to hold the skull rigidly, and this was done by embedding the head in a plaster mould. Three holes were drilled in the skull to fix the pin of the craniotome, and the flap was then cut in a series of three arcs, after which the flap was elevated with levers until its base fractured. The 'Trumbolian" instrumentation was used in the Alfred Hospital by a number of Trumble's pupils. The craniotome is made of steel, not plated and apparently not stainless. It is believed that Trumble made his craniotomes himself, in a backyard workshop.

Benjamin Rank was considered by many to be the father of plastic surgery in Australia. He was born on 14 January 1911 in Heidelberg, Victoria, where his father, Wreghitt Rank, owned a grain store and mill. His mother was Bessie née Smith. He was educated at Scotch College, Melbourne, and Ormond College, University of Melbourne, graduating with many honours and prizes. He did a two-year residency in the Royal Melbourne Hospital before going to London to specialise in surgery. There he did junior posts at St James' Hospital, Balham, but soon became fascinated by the new specialty of plastic surgery and was appointed assistant plastic surgeon at Hill End (Bart's EMS unit). Joining the Royal Australasian Army Medical Corps in 1940, he commanded their plastic surgical unit in Egypt. In 1942, he returned to Australia to set up a plastic and maxillofacial unit at Heidelberg Military Hospital. Among the patients treated there was one Flight Lieutenant John Gorton, who went on to become Prime Minister of Australia. In 1946 he was the first honorary plastic surgeon at the Royal Melbourne Hospital. He spent much time overseas and was instrumental in setting up the specialty of plastic surgery in India, for which he set up 'Interplast' - a charity supported by the Rotary Clubs to offer training and expertise to Asian and Pacific nations. He was the Sims Commonwealth Travelling Professor of the College in 1958, Moynihan lecturer in 1972, President of the British Association of Plastic Surgeons in 1965 and President of the Royal Australasian College of Surgeons from 1966 to 1968. He made important contributions to the study of Marjolin's ulcer, radiation carcinoma, and the transition from benign to malignant melanoma. He also made a major contribution to hand surgery, and his textbook Surgery of repair as applied to hand injuries (Livingstone, 1953) ran to four editions. He wrote extensively, including an autobiography, and was a talented painter. He was a tireless campaigner for no-fault motor accident insurance and was President of the St John Ambulance Association. He married Barbara Lyle Facy in 1938. They had one son Andrew, and three daughters, Helen, Julie and Mary (one of whom became a nurse). He died on 26 January 2002. Reference; https:livesonline.rcseng.ac.uk surgeon, sir benjamin rank, heidelberg military hospital, plastic surgery, royal melbourne hospital

A predominantely red carpet. Custom made with woven inscription Royal Australian Engineers 1959 Wilson R B 1968 - 2411848. Ubique Viet 66' 67' with fringes top and bottom. 5 wooden rings attached to topThis fully imported & hand woven rug was custom designed for Graeme Wilson.royal australina engineers

Cordite Wagon - 18½-inch (460mm) gauge wagons came from the Commonwealth Explosives factory at Maribyrnong in Melbourne’s western suburbs. Both have gun-metal wheels, as avoiding sparks was understandably a priority in an explosives factory. Both wagons also have water tanks to drip water on the wheels as an added precaution. Cordite, an explosive used in artillery, was manufactured and pressed into thin sheets, which still contained a quantity of acetone solvent from the manufacturing process. The sheets of cordite were laid in racks of perforated trays in the cordite wagons, which were hand-pushed to the cordite drying-house where the trucks were coupled together in rakes and warm air was blown through them. The acetone, being very volatile, was evaporated out of the cordite and recovered to be re-used in the manufacturing process. Historic - Industrial Narrow Gauge Railway - Commonwealth Explosives factory, Maribyrnong, Victoria, AustraliaCordite Wagon - Rectangular yellow wagon made of wood and brass with aluminium traysThe number 77 is on the endspuffing billy, wooden wagon, 18½-inch gauge, explosives, maribyrnong cordite factory, maribyrnong explosives factory, puffing billy museum, industrial narrow gauge railway

Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

The Lister Auto-Truck was a small monowheel tractor built for moving light loads around factories, railway yards and similar sites. They were built by R A Lister and Company of Dursley, Gloucestershire, well known for their range of small stationary engines The Auto-Truck was one of several monowheel tractors to appear in the 1920s and '30s, with the availability of small, reliable petrol engines, as developed for motorcycles and the stationary engines for which Lister were already known. These were tricycle vehicles, with the single leading wheel used for both drive and steering. Their simple construction carried most of the mechanism on this wheel as a single unit, the chassis with the trailing wheels being little more than a trailer for balance. Simplicity was a key feature. The engines were single-cylinder and air-cooled. Ignition was by magneto, rather than requiring a battery and electrical system. One of these designs was produced in the 1920s by George Grist of the Auto Mower Co., Norton St Philip, Somerset. The engine was a JAP 600 cc four-stroke air-cooled sidevalve, a typical small engine of the time. The Auto Mower Co. were Lister agents and when Lister heard of this 'Auto-Truck' they bought one for use in their own factory. It was used to carry heavy engine castings from the foundry to the machine shop. Lister customers saw them and there was such interest in wanting to buy them that Lister negotiated with Auto Mower to build them under licence. Although Lister were already well known for their small petrol stationary engines, these were heavy cast-iron engines with water hopper cooling and unsuitable for vehicle use. Lister remained with the JAP engine for the Auto-Truck. The Auto-Truck was designed for use in factories or other places with smooth surfaces of concrete or tarmac. This allowed the use of small solid-tyred wheels with only simple suspension, making the vehicle simple, cheap and lightweight. They had little ability on soft surfaces though and could even topple over if driven carelessly across slopes. Their design was a compromise between the top-heavy nature of the tall engine grouping above its wheel and a well thought-out chassis for stability. The bearing between them was a large diameter ring roller bearing, mounted at the lowest part of the chassis. This gave rigidity and stability, even after long wear. A ring of rolled channel girder was attached to the engine group and rollers on the chassis carried the load upon this. On early Auto-Trucks this bearing is set very low, in line with the chassis members, and is covered by thin steel plates. The front panel of the engine cover is distinctive with large ventilation holes and a Lister signature cut through it. Strangely this panel is made of thick cast iron, providing substantial weight high on the engine and only adding to its top heaviness. To improve visibility of moving vehicles in noisy factories, this panel was often painted white, the rest of the vehicle being Lister's usual brunswick green. The driver was seated on a Brooks bicycle saddle, which in recognition of the lack of vehicle suspension, was carried on the end of a cantilevered bar that acted as a leaf spring. A wide handlebar on the engine group was used for steering. A squeeze bar the width of this handlebar engaged the clutch. Controls included a hand throttle, a gear lever with two forward and one reverse gears, and a large handbrake lever. The engine unit rotated freely for a full 360° rotation. When used in reverse, the Auto-Truck could either be driven from the saddle, looking backwards over the driver's shoulder; or they could dismount, swivel the engine unit around and control it as a pedestrian-controlled truck from behind. Under the engine cover were two equal diameter tanks, a fuel tank for petrol and a shorter oil tank. Engine and chain-drive lubrication used a total-loss oil system, controlled by a small pump and needle valve. Info Ref: Lister Auto-Truck - Wikipedia https://en.wikipedia.org/wiki/Lister_Auto-TruckHistoric - Industrial monowheel tractor for moving light loads around factories, railway yards and similar sites.The Lister Auto-Truck - small monowheel tractor Made of steel with three wheels. Powered by a J.A.P single cylinder petrol motor which is Hand Cranked to start.Lister puffing billy, lister, lister auto truck, monowheel tractor

Zeehan & North East Dundas Tramway Bogie 1896 The North East Dundas Tramway (NEDT) was a 2 ft (610 mm) narrow gauge tramway on West Coast Tasmania that ran between Zeehan and Deep Lead (now Williamsford). It was part of Tasmanian Government Railways. The line was opened in 1896 to carry ore from the Williamsford mines to Zeehan where it would be loaded onto another train for shipment to Burnie. The narrow-gauge (2 ft) was chosen because of the extremely difficult terrain that the railway crossed, requiring several big trestle bridges, including one at the foot of Montezuma Falls. After some rain the engine and carriages would get soaked by spray from the falls. There was a break-of-gauge with the mainline 1,067 mm (3 ft 6 in) system at Zeehan. The railway was closed in 1932. The rolling stock for the Tramway was built in the Launceston Railway workshops, and comprised twenty five eight-wheel low-side trucks, tare 3 tons 1 cwt. 1 qr., load 10 tons; six eight-wheel flat trucks, tare 2 tons 18 cwt. 1 qr., load 10 tons; two four-wheel bolster trucks, for carrying long timber, tare 1 ton 19 cwt., load 5 tons; and four passenger cars, each with six cross-seats with reversible backs, to carry eighteen passengers, also a locker for mails and parcels. All trucks and cars have cast-steel wheels 21 inches in diameter and are fitted with automatic vacuum brakes. The trucks have side levers and the cars have hand-screw brakes. The vacuum brake can be worked from the engine or from the passenger cars, which act as brake vans. When this brake was introduced, one effect was to accelerate the journey speed by about 10 minutes owing to more even running on down gradients. Historic - Industrial Narrow Gauge railway - Bogie used on the Zeehan & North East Dundas Tramway, Tasmania, Australia Bogie made from steel, iron and wrought ironZN & NTDS ML TRAM 1896 Griffinpuffing billy, bogie, zeehan & north east dundas tramway bogie, zeehan & north east dundas tramway, industrial narrow gauge railway, gauge: 2' (610 mm)

Electric staff - Electric staff instruments The staff and ticket system was still too inflexible for busy lines, as it did not allow for the situation where the train intended to carry the actual token was cancelled or running very late. To provide for this, the electric train token system was developed. Each single-line section is provided with a pair of token instruments, one at the signal box at each end. A supply of identical tokens is stored in the instruments, which are connected by telegraph lines. A Staff can be removed from one instrument only if both signalmen co-operate in agreeing to the release. Once a Staff has been removed, another cannot be removed until the token which is "out" is replaced in either instrument. (There are variations on this sequence of events.) By this means, it can be ensured that at any one time, only one token is available to be issued to a driver. Staff belonging to adjacent sections have different configurations to prevent them being inserted into the wrong instrument. Nevertheless, in the Abermule train collision in 1921 and lax working procedures allowed the safeguards provided by the electric Staff system to be circumvented; a driver was handed a Staff for the wrong section, and without reading the information listed on the staff, proceeded on the mistaken belief that the Staff was correct. To prevent this, it became a requirement in the UK for the signals controlling entry to the single line section (starting or section signals) to be locked at danger unless a token has been released from the relevant Staff instrument. Historic - Victorian Railways Electric Staff Instrument Electric Staff Instrument made of Iron , Brass and Glasspuffing billy, electric staff instrument, victorian railways

Porters Luggage Trolley - large red one Used for transporting luggage and other items on a railway platforms by porters and other station staff.Historic - Victorian Railways - Station Porters platform Luggage Trolley Large Porters Trolley - made of wood and steelpuffing billy, victorian railways, porter, luggage, hand trolley

Appletons Patent Railway Warning Lamp with Sherwood Style burner Used by Gangers during track work at night Appletons was an early pioneer of railway lamp signal lamp Alfred Edward Appleton invented and patented the Spinner Railway signal lamp in England in 1897. Appleton lamps were patented and manufactured by Alfred Edward Appleton at a factory in Sherwood during the early 1920's to late 50's and widely used throughout Queensland Railways. Alfred Edward Appleton's father was a railway pointsman and porter on the Great Western Railway in Tewkesbury England Historic - Early Hand signalling Lantern Appletons Patent Railway Warning Lamp made of tin & metal and glassAppletons Patentpuffing billy, appleton warning lamp, lamp

10 NU Louvre Van - Louvred Truck (11) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 10.VA - 30/12/1911 NWS Built new - / /1926 - To NU 10.VA - NU 10.VA - / 5/1926 - Modified AC Malco /12/1972 BEL To NW 10.VA Sec72/3400, RS72/9371 NW 10.VA - 26/ 8/1976 CLS Photograph #662.2-.4: and end detail 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 Build Date: 30/12/1911 NWS Built new Victorian Heritage Register (VHR) Number H2187 NW 10 is a 1972 reclassification of NU 10. It is presumed the van was used to store tools and equipment. In 1977, the van was removed from railway records and control handed to the Puffing Billy group.Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock CollectionWooden Louvered Van - Made of Timber on a Wrought iron frame - current condition Untrafficable10 NU puffing billy, louvered van, 10nu, victorian railways, 2'6" gauge, narrow gauge rolling stock

Van 3 NUU - Louvred Truck (11) VR Service History 3/12/1900 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 7 tons Capacity 10 tons Built 1898 - 1911 Number Built 14 In use 5 To be restored None *NUU 3.VA - 3/12/1900 NWS Built new - / /1926 - To NU 3.VA - NU 3.VA - circa 1926 - Modified AC Malco 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 NUU The standard louvre van design for the Victorian narrow-gauge lines, the NUU vehicles were constructed in three batches; the first seven from 1899 to 1901, an eighth in 1906 and the last six in 1911, for a total class of fourteen. They looked very similar to the U vans of the Broad Gauge, although two photographs[1][2] of NUU 1 show that its body may have been white for some time. NU In 1926 the class was relettered to simply NU, with no changes to numbers. NU 4 was scrapped in 1938, but otherwise the class remained intact until 1954, when seven members (2, 5, 7, 8, 9, 11 and 12) were sold to Coulston & Hyder, who dispersed the wagons among locations on the Wangarrata to Whitfield line. As of 1996, vans 7 and 12 were at Moyhu, while van 11 was destroyed by fire in 1978. Wagons 6 and 1 were scrapped in 1957 and 1958 respectively, while in 1954 van 13 was recorded as being sold to the Puffing Billy Preservation Society. In 1977, the remaining vans 3, 10 and 14 were handed over to the Emerald Tourist Railway Board, and removed from Victorian Railways records. The Puffing Billy Railway now posesses vans 3, 8, 10, 13 and 14. Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered VanWooden Louvered Van - Made of Timber on a Wrought iron frame3 NUUpuffing billy, 3 nuu, louvered van, 2'6" guage, victorian railways, narrow gauge rolling stock

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 216 NQR - Open Medium Truck 15/ 1/1914 NWS Built new VR Service History *NQR 216.VA - 15/ 1/1914 NWS Built new - / /1926 - To NQ 216.VA - Puffing Billy Service History or Notes April 2016 - Trial fitting of brake rigging May 2016 - Riveting of the draw gear castings in progress July 2016 - Riveting of the draw gear castings in progress. Truss rods threaded ready for fitting Aug 2016 - Rivetting of the draw gear castings in progress. Draw gear and couplers being evaluated. Sept 2016 - Riveting of the draw gear castings in progress. Draw gear and couplers being overhauled. Oct 2016 - Riveting of the draw gear castings completed, brake piping installed. Nov 2016 - Floor installed, under framing welding completed, fitting of side doors, hand brake fitted Dec 2016 - Car Workshop - Side panels fitted, end panels to be fitted Jan 2017 - Couplers fitted, brake rodding connected, transferred to Emerald for bogie work and sign writing. Feb 2017 - At Emerald - Tyres machined, braking system being prepared Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck216 NQR - Open Medium Truck made of Steel and metal216 NQRpuffing billy railway, pbr, rolling stock , 216 nqr - open medium truck, victorian railways, nqr - open medium truck

This Victorian railways constructed turntable is used for turning around locomotives. It is 16.2 meters long and is hand pushed either direction. Originally broad gauge (5 foot 3 inches) and located in the Newport Locomotive workshop area it was relocated to emerald and 2-foot 6-inch railway track fitted to it and is used by the Puffing Billy Railway to turn their locomotives and carriages Historic - Victorian Railways - Turntable used at Newport Narrow Gauge Turntable made of metal and steelturntable, victorian railways, puffing billy, emerald, newport

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

Four NSWTD Railway marker Oil lamps at Nobelius Packing shed Item stamped numbers unknown Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil LampFour NSWTD Railway marker Oil lamps made of metal and glass Railway lamp, paraffin, metal / glass / fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870-1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTDpuffing billy railway , pbr, four nswtd railway marker oil lamps

Life Buoy from HMAS Sydney II - On 19 November 1941, Sydney was involved in a mutually destructive engagement with the German auxiliary cruiser Kormoran, and was lost with all hands (645 aboard).Three Australian warships have carried the name Sydney. Following the tragic loss of HMAS Sydney II and all 645 crew members in 1941 the Life Buoy was found in poor condition discarded in a bin at Spectacle Island in Sydney and later restored. The Life Buoy made from kapok ceased to be used by the RAN in the early 1950's. Solid white circle surrounded by attached ropeHMAS SYDNEY hmas sydney, life buoy

History has it that the origins of the Slouch Hat began with the Victorian Mounted Rifles; a hat of similar design had been worn in South Africa by the Cape Mounted Rifles for many years before 1885. The design of the Victorian Mounted Rifle hat originated from headgear of native police in Burma where Lieutenant-Colonel Tom Price had recognised its value. The Victorian hat was an ordinary bush felt hat turned up on the right side. The intention of turning up the right side of the hat was to ensure it would not be caught during the drill movement of “shoulder arms” from “order arms”. The Slouch Hat became standard issue headdress in 1903 and its brim position was mostly standardised. The slouch hat became a famous symbol of the Australian fighting man during World War One and continued to be worn throughout World War Two. Its use since that time has made it a national symbol.Slouch Hat - made of fur felt with an 8 fold hat band (puggaree) it has the blue/gold unit badge on the band denoting the 8th Light Horse brigade with a leather chin strap. The right hand side is held by a brass rising sun badge.army, slouch hat

Made especially for the Late Mr. Rickard about 1900.1 & .2 Pair brown bespoke leather lace boots size 8, lace on left boot missingOn sole of each boot Made in Australia Cork filled Waterproof F.A.C. Hand sewn Sticker marked "137"boots, rickard, handsewn boots

On 19 November 1941, HMAS Sydney was involved in a mutually destructive engagement with the German auxiliary cruiser Kormoran, and was lost with all hands (645) aboard.This object was handmade to house a Life Buoy from HMAS Sydney II which was lost at sea with all hands on board in 1941. The Life Buoy made from kapok ceased to be used by the RAN in the early 1950's. It was found in poor condition discarded in a bin at Spectacle Island in Sydney and later restored.Long narrow timber board mounted with timber crest consisting of crown and red anchor on white background within gold coloured circled rope.SYDNEY Gold coloured plaque - Donated by Peter L CARDWELL Ex HMAS SYDNEY (3) 2002life buoy, hmas sydney

The pram was made by Otto Gottlieb, for his daughter Ruth's fifth birthday. Otto and family were internees in camp 3. Artwork by unknown artist. Originally had a hood but this is missing.Timber pram on metal rectangular "Wheels". Red metal handles. Sides are painted grey and trimmed in red. Hand painted animals, sea creatures, boats and a lighthouse. otto gottlieb, ruth gottlieb, internment camp wood work