This rounders bat was used by the students at Bogong Primary School.Historical: Bogong Primary School was opened for the Kiewa Hydro Electric Scheme workers. Provenance: Bogong Primary School sport.Wooden bat. The face of the bat is flat and the other side becomes thicker (is tapered) towards the centre in a longitudinal direction. The handle is cylindrical.'Champion' 3 quarters of the way up the bat towards the handle on the flat side of the bat. On the reverse side same position, Made in / Pakistan. On the flat side: Bogong has been written in thick black but faded paint.rounders. sport. bogong primary school. kiewa hydro electric scheme. game

This shunt is a type of resistor built of copper and designed to carry a current. It was part of the Hydro generator control metering system. It reduces the large current to a small voltage.Historical: This equipment represents a major construction and ongoing operational industry dealing with the supply of hydro electricity to Victoria.Made of copper the shunt has a middle cube with 12 sheets of copper, 5mm apart formed like shelves. On either side of the cube are two shelves coming out from the middle. Both have 2 hollow circles 17.5mm in diameter 25 mm apart in the middle. At the Join of the 'shelves' and cube is a screw on each side.Screwed in metal plaque: Deriv. 1662691 / OHM 0.0000833 / AMP 1200 on the side of the cube above a shelf and on the opposite shelf: ALTO ----> (also a metal plaque screwed on). kiewa hydro electric scheme. secv. hydro generator. victorian electricity grid, power station. electricity., resistor

The State Electricity Commission of Victoria used signs to warn people of danger when near high voltage equipment.The S.E.C.V. built the Kiewa Hydro Electric Scheme from the late 1940s. Their towers and switch boards had high voltage equipment.Red, white, black and yellow steel sign with a circular hole at the top left hand corner. Used to warn people of danger near high voltage equipment. The back is white.Danger / High Voltage / Do Not Climbsecv. kiewa hydro electric scheme. electricity. sign.

Insulates electrical wire which is attached between the outside ridges. It is screwed onto the cross arm of a power pole. It is non conductive so electricity doesn't short to the ground.Used on the power poles in the Kiewa Valley.Clear tinted glass (one green & one brown) domed shaped insulator. Above centre there are 2 ridges to enable the electrical wire/cable to be fixed on. The closed end has a screw thread down to half way to enable it to be attached to a pole.Green one has 'Agee' on side of the open endkiewa hydro electric scheme. electricity. power lines. insulator

Insulates electrical wire which is attached in the groove towards the narrow end. It is screwed onto the cross arm of a power pole. Non conductive so that electricity doesn't short out to the ground.Used on power poles in the Kiewa Valley.Cream coloured porcelain cylindrical shaped insulator with a groove towards the narrower closed end. Inside the narrow end it is threaded for screwing.On the side of the closed end - "KP / 64"kiewa hydro electric scheme. electricity. power lines. insulator

Insulates electrical wire/cable which is attached between the narrow and wide ends of the 'bell' shape (in the groove). Screwed onto the cross arm of a power pole. Non conductive so electricity doesn't short out to the ground.Used on power poles in the Kiewa Valley.White porcelain bell shaped insulator with an indent between the wide open end and the narrow closed end. The indent is for the wire/cable to be attached. The wide end is open with a white porcelain cylinder inside narrowing to thread for screwing, in the narrow section. kiewa hydro electric scheme. electricity. power lines. insulator.

Insulates electrical wire/cable which is attached between narrow and wide ends of the 'bell' shape (in a groove). Screwed onto the cross arm of a power pole. Non conductive so electricity doesn't short out to the ground. Used on power poles in the Kiewa Valley.White porcelain bell shaped insulator with an indent between the wide open end and the narrow closed end (for cable to be attached). The wide end is open with a white porcelain cylinder inside narrowing to thread for screwing in the narrow section.kiewa hydro electric scheme. electricity. power lines. insulator.

The SECV had chalets, cafes, mess halls and tea rooms all over Victoria including their construction sites. The SECV had a stores system which purchased thousands of sets of crockery and cutlery for use by personnel. There was a system of chefs, cooks, tea persons etc. to supply food and beverages to the workers. This saucer was used at one of the sites on the Kiewa Hydro Electric Scheme.Heavy, white ceramic saucer with State Electricity Commission of Victoria 1921 log/insignia on inside lip. Curves up to sides. On base, also inscribed in red are details of the makers.State Electricity Commission Victoria / 1921 On base: Vitrified / Sold by / Cafe & Hotel Supplies / Pty Ltd / DunnBennett & Co. ITC / Burslem / Made in Englandkiewa hydro electric scheme. mount beauty chalet. bogong mess hall. state electricity commission of victoria. crockery.

At the time of writing this book The State Electricity Commission of Victoria had been in existence for 30 years. This book tells something of its progress and achievements during that period. It includes brown coal and water power. The Commission was to develop and use these natural resources through the expertise and experience of the Commissioners, its staff and employees. Historical: Chapter 5 "The War Years - and Kiewa." describes the early stages of the Kiewa Hydro Electric Scheme. Photos, map and diagrams of the Kiewa Scheme are also included. Hard cover blue bound book with the SECV insignia and the title "Three Decades" both in gold on the front cover. Book includes coloured and black and white photos.Handwritten inside front cover: "Bob Burnett". Title page: hand written in print and crossed out: "L.D.Miller / Tawonga". Not crossed out - "(Cheryl)"state electricity commission of victoria. kiewa hydro electric scheme. bogong high plains. pretty valley. kiewa valley.

The S.E.C.V. published the Bi-Monthly magazine for employees. This one is Vol. 14, No. 8 / April - May. 1956The Journal includes small articles on men who were working on the Kiewa Hydro Electric Scheme.Black and white paper cover with photo of a man working up a power pole. The 'S' has an orange back ground.The back cover also has a photo of a generator.The journal is held together by 2 staples and has 32 pages.secv. kiewa hydro electric scheme. journal.

This electric washing machine was typical of the machines in the homes of Mt Beauty during the 1950's. This one has a wringer attached enabling the washing to be pushed through squeezing the water out after washing.Mt Beauty township was constructed in the early 1950s with electricity connected. Residents were employees of the State Electricity Commission of Victoria and worked on the Kiewa Hydro Electric Scheme.Metal green cylinder standing on 4 roller coasters. Cylinder has 3 sections - bottom short & yellow, the rest divided into 2, each section is held by a strip of steel bracing. The top section of the cylinder is hollow with a stainless steel metal agitator with 3 'wings'. The cylinder has a rotatable switch on the outside and a moveable knob. Opposite on the outside is a metal pipe widening to the wringer which hangs above the cylinder. The green wringer has 2 cloth covered cylinders that can be separated by moving knobs. A flat stainless steel curved flat surface comes out at an angle below the cloth cylinder. An electric cord is attached. The cylinder has a lid with a knob in its middle.On the wringer: "Stampco"electric washing machine. mt beauty. s.e.c.v. kiewa hydro electric scheme. home duties. housework. wringer washing machine.

Electric fans were used for cooling rooms prior to air conditioning.This fan was used by S.E.C.V. office workers working on the Kiewa Hydro Electric Scheme. Small electric swivel fan. This heavy black metal fan has 4 curved 'wings' covered by protecting wire consisting of 2 wire rings joined by 6 curved pieces of wire covering the sides and front. Attached to the motor that can swivel and to the base is a black rubber covered electric cord. The base forms a stand with a control knob for speed and swivel options. On a plaque: Menominee / Fan Motor / 55182591 Serial No. 200 volts / ACC current 6 cycles / Menominee Electric Mfg. Co. / Menominee ..? Control knob: 0,1,2,3 along slotelectric fan; state electricity commission of victoria; kiewa hydro electric scheme; office furniture

Electric fans were used for cooling rooms prior to air conditioning.This portable fan was used on the Kiewa Hydro Electric Scheme by office workers.Green metal swivel fan with base, motor and 4 cream angled 'wings' covered by 3 wire rings connected by 6 pieces of curved wire that cover the blades at the side and front. An electric grey rubber cord is attached. There is a lever in the base for moving from 'off to 1.2.or 3' (but no marks to indicate these positions.)Base: "Elcon Fan / Made in Australia"electric fan; state electricity commission of victoria; office equipment; kiewa hydro electric scheme;

This sign warned people not to go near electric wires. Consequences are explained. Public Health & Safety has changed over the years as have the consequences. Historic: Used by the S.E.C. on the Kiewa Hydro Electric Scheme. White metal sign with black and red writing warning people to keep away from electrical wires.(In black unless stated differently) "State Electricity Commission / of Victoria / Danger (red) / Contact with electric wires will cause Death (last word in red) / 10 pound reward paid for information leading to / Conviction for damaging commission's property / Maximum penalty Imprisonment for / 10 years. By order L G Morrison / Secretary"state electricity commission of victoria; warning sign; public health and safety; kiewa hydro electric scheme

Telephones were mounted on the wall and were operated by turning a small handle situated in the middle of the phone. This connected the speaker to the switch board where they were 'put through' to the other end (speaker).Wall phones were used by State Electricity Commission of Victoria workers and their families on the Kiewa Hydro Electric Scheme. The SECV had a switchboard located at Mt Beauty. Also refer to article in "This Week" Newsletter 30th June 2023 and attached to KVHS 0050Black bakelite wall mounted telephone with handset connected by black spiral plastic cord. The round dial in the centre has a small handle with knob for turning. The base is silver steel with screws to attach it to the wall. The handset has a circular end with 4 small holes for the ear and the other end, the speaker end has 3 rings of small holes and a curved protective mouth piece to direct speech into the holes.On white circle in centre of dial: "To call turn handle and lift hand set. / When finished replace handset and turn handle" Handset embossed on inner side: 164 55wall mounted telephone; state electricity commission of victoria; kiewa hydro electric scheme; telecommunications; switchboard

In 1940 Field Headquarters for the Kiewa Scheme were established at Bogong with office, workshop facilities and accommodation for workmen, staff and some families constructed. (There had been a 'tent camp' on this site in 1939 but was destroyed by bushfires) Construction of accommodation continued until 1947. A total of 40 houses plus a hostel for single staff, post office, police station, medical centre and primary school all with water and sewerage and electricity supply. The staff hostel was known as Kiewa House and is now occupied by the Education Department. Lake Guy was named after Mr. L.T. Guy who was the Resident Engineer in charge of construction work and associated activities on the Kiewa area. He held this position from 1939 to November 1946 when he was transferred to Head Office.The Bogong Township was developed firstly as an accommodation centre (base camp) for construction workers employed under the Kiewa Hydroelectric Scheme. Due to the influx of European workers into the Township the beautification of the immediate surrounds(gardens etc.) had a distinct European flavour. This environment has been very beneficial for tourism in later years. Strict environmental control has not allowed for any extensive redevelopment in tourist accommodation and basically restricted it to the accommodation initially built for the construction workers. Activities such a bike riding, snow skiing, restricted horse riding and bush walking on the Alpine plains and mountains are now a viable part of the Kiewa Valley Tourist Industry. The lake is one of the many water storage storage reservoirs used to supply the power stations their main power to run the huge turbines generating the final product, electricityThis black and white photograph shot from the shores of Lake Guy toward the mountain range of the Victorian Alps details the early construction of the construction worker's accommodation of the Bogong Village. The paper is of 200gms and is not photographic paper and can be assumed to be a reproduction of an original photobogong village circa 1930 to 1950, kiewa hydro-electricity scheme, victorian alpine region mid 1900s

This resistor was part of the Hydro generator control metering system which displays what electricity is produced at the underground generators. The control centre can be hundreds of meters above the generators and this resistor reduces the large current to a small voltage entering a calibrated control monitor. This resistor is highly significant to the Kiewa Valley because it represents a major construction and ongoing operational industry dealing with the supply of hydro electricity to Victoria. Although it is relatively small in size it is part of the controlling mechanism for the supply of a non polluting energy source for home and industrial use.This mainly metal and wire resistor has been built of copper and brass and designed to carry a current of 2000 Amperes. Wires are wound around a non conductive cement block which has grooves on the top and bottom ledges to hold the wires snuggle into place. At the rear there are three connection rods which have long 5mm thick screws (to fasten cable ends)On one side it is scribed "0.2 OHMS" and underneath this "10 AMPS"kiewa hydro electricity scheme, victorian state electricity commission, transformers

This linesman belt was used under the 1947 Electricity Regulations and before tighter Occupation and Health regulations (late 1990's early 2000's) were introduced that mechanical lifting platforms(wherever possible) replaced the belt up the pole method.The safety concern was that it required that tools needed by the linesman had to be placed in a large canvas bag and attached to the belt (extra weight) then the linesman had to climb the ladder. Ladders had to be at the correct angle and not able to "slip" from their initial footings. A full harness and a secondary fall belt is now mandatory for pole linesmen. The safety of fellow workers could be compromised if they were required to assist or recover the first linesman if needed. In 2006 an additional 269 registered lineworkers were employed. Please note that the terminology of linesman has become unisex. The linesman's belt enabled the linesman to place his feet against the pole adjust the belt (if needed) and lean back securely allowing both hands to be free to work with. This linesman belt is very significant to the Kiewa Valley due to the numerous poles and high voltage overhead power structures that needed maintenance for the extensive "mushroom" installation of electrical power polls(wood and metal). On high poles (steel) climbing pegs were welded on, however in the Alpine areas snow in winter caused an OH&S problem which were hard to overcome. The safety of a linesman when maintenance of electricity line on poles can be highlighted by the New Zealand linesman who survived an 11,000 volt shock when carrying out maintenance. For the record 11,000 volts is four times more powerful than execution by "the electric chair". The maintenance of the linesman's belt was his responsibility (keeping it clean and in "good" condition). Labour laws change this initial responsibility, from the linesman, to the employer. Climbing pegs were installed on higher poles that extended beyond the reach of ladders.This thick leather linesman belt is made from two lengths of heavy lengths of leather straps sewn together to make up 80% of the belt. The remaining 20% is "the belt tonge" which has eleven holes for three (solid steel tang) buckle connections.kiewa hydro electricity scheme, victorian state electricity commission, relays, generators, electrical pole maintenance

The Tawonga District Hospital opened in the early 1950's in the Kiewa Valley to treat local patients from Mt Beauty and the residents of the KIewa Valley. The State Electricity Commission of Victoria assisted with the building of the hospital as the population of Mt Beauty increased with the S.E.C. workers and their families during the construction of the Kiewa Hydro Electric Scheme. The Tawonga Hospital was later relocated to Mt Beauty. All the enamel equipment was eventually replaced with stainless steel.This grey enamel basin is large with a royal blue lip. It was used in the Tawonga District Hospital to wash patients.enamel basin, tawonga hospital, medical, kiewa hydro electric scheme

Bogong State School opened in 1941 to provide an education for the employees of the State Electricity Commission of Victoria. The school had up to date equipment and received glowing reports from School inspectors. It closed c1986.Historical: The Bogong State School was opened for the children of S.E.C.V. workers who lived at Bogong in a remote part of north east Victoria. The nearest school would have been 14 miles away and over mountain roads subject to heavy construction traffic and extremes of climatic conditions. Metal sign painted white with thin red border and black block capital letters and numbers. There is a hole in the middle top and middle bottom of the sign."State School / No. 4590"state school. bogong. education. state electricity of victoria. kiewa hydro electric scheme.

Ron White was born in 1920. He received a Diploma of Mechanical Engineering at Footscray Technical School in 1946. He started work as a laboratory assistant and after several promotions was appointed Senior Operator in 1948. In 1949, he was Engineer, Grade 1 (Hydro Areas). After further promotions he became Assistant Area Engineer, Rubicon at new Eildon Power Station and Area Engineer, Kiewa in commissioning Mt Beauty Terminal Station and West Kiewa Power Station.. By 1956, he was the Area Operations Engineer at Kiewa and four years later the Kiewa Electrical Superintendent (Operations and Maintenance) . In 1961, he was officially recognised as deputy for the General Superintendent, Kiewa. In 1966 he was appointed General Superintendent Kiewa and Kiewa became 'a branch of the Transmission Department'. In 1974, the Rubicon / Eildon Area was also under Ron's control. His title was "Principal Hydro Engineer, Hydro Division, Transmission Operations Department. He held this position until his retirement in 1985.Ron White was an important identity in his role as Principal Hydro Engineer from 1966 to 1985 after the completion of the Kiewa Hydro Electric Scheme. His long period of service involved him in the construction, operation and maintenance of the SECV's Hydro Electric Schemes and administration of related catchment areas. He had a close association with the local communities and care for the welfare of employees. He lived in Mt Beauty and was well respected in the community and beyond. He passed away on 30 September 2019, aged 99 years.A) History of Ron White's Working Life: including papers relating to "Promotion & Staff Appointment" B) Ron White's Retirement - 11th Jan. 1985: papers, cards, letters, photos, disc/plaque C) Ron White's Certificates: Diploma of Mechanical Engineering; First Aid; D) Ron White's Correspondence - miscellaneous E) Ron White's History of the 'Kiewa Scheme' from 1936- 1966. Written 1986 F) Ron White's Photo album Includes photos of him and the 2003 bushfires G) Miscellaneous Photos (not labelled) from Ron's photo album. Possibly relatives including nieces and nephews. H) Pewter Mug presented to Ron - Water Board I) Wall hanging presented to Ron - Scouts J) Ron White's Slide Ruler & Mathematical Instruments K) Collection of 7 books owned by Ron L) Starting Pistol Caps box M) Ice-cream serverF) One photo of Ron with 'Ken Connors'. One photo with 'l to r: Norm Middleton, Graham Napier, Ron White, Les Peart.' G) 2003 fires has a note re time, date and whereabouts of fires H) "Presented To / Ron White / In Appreciation For Service / To The / Kiewa Valley / Water Authority / And / Its predecessor Bodies / December 1994 I) Wall hanging: On emblem - "Lord Baden-Powell Society / The Scout Association of Australia". On Name Plate below - Ronald K. White 1989" J) mathematical Instruments have 'R. W' embossed in red on the corner of the cover M) 100 Straitline, Starting Pistol Caps N) National Ice-cream Server with stainless steel spring Size 20 ron white, hydro engineer, kiewa hydro electric scheme

The book includes detailed accounts in 4 sections of 1. History and Exploration 2. General Geology 3. Vegetation and slide set index 4. Climate ...Important knowledge/study for the construction of the Kiewa Hydro Electric Scheme on the Bogong High Plains.Cream cardboard cover book with black spiral binding. Title printed in black on cover. 46 pages printed on both sides includes diagrams. Clear blue plastic sheet as last page.e. j. minty, bogong high plains, kiewa hydro electric scheme

A photo of Beauty Avenue houses looking south. A good example of the garden's created very early in Mount Beauty's history. Photo circa 1947These houses were built for the workers and their families during the construction phase of the Kiewa Hydro Electric Scheme by the State Electricity Commission of Victoria.Large coloured photograph with mountains in the background, houses,and SEC poles in the centre, and gardens in the foregroundOn the back in pencil 13411mount beauty housing, kiewa hydro electric scheme, mount beauty gardens, mount beauty township

The pendulum weight was used to define a vertical line. Being so large and heavy it was possibly used from a tower or a dam. It was held by one end of a wire and measured any tilt of the structure in any direction.Possibly used on the Kiewa Hydro Electric Scheme during the construction of the dam walls and Electric Powerline towers.Cone shiny brass pendulum weight with cylinder shape that i hollow at one end. The hollow is threaded inside. The part that fits the hollow end is missing.pendulum weight, measurement, kiewa hydro electric scheme

The Bogong Village was originally constructed (1937-1940) by the State Electricity Commission to house, engineers and construction workers working on the Kiewa Hydroelectric Scheme. These workers were initially settled in 26 houses and were mainly of European heritage. At the completion of the scheme, in the 1960's, the village was opened to public/tourism use. This photograph shows the village before beautification for tourism was introduced and "bare bones" homes and village usage existed.This photo clearly presents a period of restricted human occupation of a very fragile Alpine environment(up to 4000 workmen involved). This was the beginning of a planned and controlled form of sustainable tourist orientated development of the Victorian Alps and high plains region. The Bogong Township was the base camp for workers employed by the State Electricity Commission. After the construction phase was completed, the planning and controls originating from this period have been modified to allow a greater public access of this unique environment.Photograph of a framed glass enclosed black and white photograph of the Bogong settlement Paper details "KodakXtraLife paper" on back of photo. bogong village, bogong township, sec alpine constructions, hydro, kiewa scheme

It is assumed that a member of the Ballarat School of Mines attended the commencement of work at the Snowy Mountains hydro-electric centre.Burgundy cover with gold printing. Black print, photos and diagrams on white paper (31 pages). Bound by 3 staples. The contents include the story of the Snowy. Images include W.J. McKell, J.B. (Ben) Chifley, J. McGirr, Nelson Lemmon, Hume Weir, Jindabyne valley (now flooded), Jindabyne township (now flooded), illustration of water Power, survey team at Adaminaby, Snowy Mountains Relief Plan, Horseman crossing the Eucumbene River, Mildura, Burrinjuck Dam under construction, transmission lines, W. Hudson.snowy mountains hydro-electricty scheme, snowy mountains hydro-electric authority

1) Young men work on steam turbines at the Yallourn Power Station .2) View of the Turbine Floor at Yallourn Power Stationyallourn, yallourn power station, turbines, steam turbines, engineers, rubiocon hydro electric scheme, geelong power station

non-fictionThis book tells the human story of the first decade of building the great Snowy Mountains Hydro-Electric Scheme, with adventures and anecdotes told by the workers themselves, and illustrated with unusual photographs. Appendices give further information about the project and list the workers named in Snowy records. The author began his 10 years with the Electrical and Mechanical Division at the age of 20. The construction of the Snowy Mountains Hydro-electric Scheme is a well-documented part of our nation’s history and a leading example of Australian innovation and ingenuity. As far back as the 1880s, Australians had been considering diverting water from some of Australia’s best-known rivers – the Murray, Murrumbidgee, Snowy and Tumut – to drought-proof parts of NSW and Victoria. It was not until 1944 that Commonwealth and State governments formed a committee to examine the development of water resources in the Snowy Mountains area. As a result of their work, on 7 July 1949, the Commonwealth Parliament passed legislation to establish a Statutory Authority and start construction of the Snowy Scheme. NSW. Construction was completed in 1974 at a total cost of $820 million. On completion, the Scheme consisted of seven power stations, 16 major dams, 80 kilometres of aqueducts and 145 kilometres of interconnected tunnels.snowy mountains hydro-electric scheme, hydroelectric power plants, snowy mountains

The Victorian Government took control of power generation in 1921, forming the State Electricity Commission (SEC). Construction approval on a grand scheme to build five power stations with a combined capacity of 289 megawatts was received in 1938, and the Clover Power Station was completed by 1945. The original scheme was dramatically pruned after World War II and only two more power stations were built. The Junction Dam and Clover Dam Power Station, stages of the Kiewa Hydro-Electric Scheme, were needed to meet the increased power demands of the wartime industry in Victoria. Clover added 26 megawatts to the grid. Junction Dam was completed and ready to hold water by September 1943, but was emptied in December 1943 and not filled again until May 1944. Construction of Clover Power Station commenced in July 1941 and both turbines were in service by May 1945.Clover Power Station and Junction Dam were part of the Kiewa Hydro Electric Scheme constructed by the State Electricity Commission of Victoria.Black and white photograph of an unidentified piece of equipment (possibly projection equipment) presumed to be used in one of the power stations ie: Clover Power Station or Junction Dam as part of the Kiewa Hydro Electric Schemeprojection equipment;

The Snowy Water Inquiry was commissioned in 1998 with a brief to recommend environmental water release options to the Commonwealth, Victorian, and NSW Governments so that corporatisation of the Snowy Mountains Scheme could proceed. These release options related to the Snowy River below Jindabyne, the Murray River and other rivers associated with the Scheme. The Inquiry objectives were that the recommendations would not adversely impact on water supplies to existing irrigators or the viability of the Snowy Mountains Scheme. (ref snowyhydro.com.au)This report contains information about water allocation and uses of the Snowy River.A book of 160 pp - Snowy River Inquiry Final report 23rd October 1998. Submitted to the Governments of New South Wales and Victoria / Commissioner: The Hon. Robert Webster. On the front cover are three aerial photographs of the Snowy River and Snowy Hydro Scheme. The book contains maps and photographs. snowy-river snowy-hydro snowy-mountains government-inquiry