Set of three 35mm Kodak white cardboard colour slide by Keith Kings of 16 or 17 /3/1968. .1 - W5 834 - on temporary track in Glenferrie Rd during relay looking, south to Kooyong railway station. .2 - photo showing the temporary track and the new 102 lb rail laid out pending welding. .3 - Photo showing W2 418 in Glenferrie Road and trackwork. Route 69" Has the Kooyong Tennis courts on the right hand side. See Keith's slide notes.Keith Kings stamp and number "20-1, 20-2 and 20-3", with details of exposure. .1 - "W5 834 - on temporary track in Glenferrie Rd during relay, south to Kooyong railway station. - 16/3/68" .2 - "Glenferrie Rd relay new 102 lb rail in approximate position in excavation. Ashes rolled as foundation. Temporary track on left. 17/3/68" .3 - temporary track at left being excavated and track drain laid. W2 418 on old track on right. 17/3/68"trams, tramways, glenferrie road, kooyong, trackwork, temporary track, w5 class, w2 class, route 69, tram 834, tram 418

Set of 8 black and white photographs of the SEC Ballarat track welding truck, Reg. No. 119 341. Truck is a British Bedford truck, model WHG, built by GMH Melbourne between 1932 and 1934. Has a fabric roof, chassis fitted with a tray top body, side tool box, metal frame and covered with canvas, fitted out with a motor generator set, welding equipment and oxy acetylene bottles. Also fitted with a spot light - 'Auto Reel Lite". - See Related Items sheet on truck notes provided by Kevin Oates, MFESB workshops, 4/2001. (Scan of this sheet of the Kodak folder added 15-8-2017 - see pdf file.) 1705.1 - side on view of truck with covers down, except for opening at back. Photographed in Wendouree Parade with two different boat sheds in the background. 1705.2 - view with drivers side cover opened, showing equipment arrangement. 1705.3 - close up view of motor generator set and controls and one of the oxy acetylene bottles. 1705.4 - view showing equipment laid out on the roadway, welding cover, seat, grinder, cables, shovels, welding mask etc. 1705.5 - close up view of motor generator control panel and associated cables. 1705.6 - view of side of truck showing all equipment. 1705.7 - vertical format photo from rear of truck showing equipment laid out and wandering lead connected to the overhead. Also shows high voltage wires on a power pole fitted with a bracket arm. 1705.8 - view of truck from the front, with SEC symbol on side, with a covers closed. Thought to be photographed at loop in Wendouree Parade on the View Point line, near Mill St. Prints when donated to the BTM were contained within a red and yellow "Kodak" folder. Folder stored with catalogue worksheet. On rear of folder in ink is number "53569" and stamped on the front is number "984" and written in front top left hand cover, "8 prints" and in top right hand corner word "Sarah". See Notes provided by Kevin Oates of the MFESB (Metro Fire Brigade Melbourne) Thornbury workshops on the truck, manufacture and engine. A survey of Wendouree Parade on 22/4/2001 did not show the boat sheds or power lines featured in the photographed. Thought to be in vicinity of Power station because of the high voltage lines on the power poles.Stamped on rear in black ink, "984" on photos 1705.3 to 1705.8.trams, tramways, welding truck, trackwork, secv, wendouree parade

These photographs were taken just after the McKillop's Bridge was completed after the flood damage. The current McKillop’s Bridge was built by the Country Roads Board in two stages between 1931-36, during which its height was raised after the original bridge superstructure was washed away in record floods of January 1934, prior to its original official opening. In its reconstructed form the original concrete abutments were turned into additional piers and the welded-steel trusses were cantilevered back over them to meet the new higher road approaches. It is sited at McKillops Crossing, named after pioneer overlanding squatter George McKillop who crossed here in 1835. This was a stock crossing place for almost a century before the bridge was constructed. (info. from Victoria Heritage Register)This is a pictorial record of the history of McKillop's Bridge, in itself of historical significance for its association with Victoria's long and important pastoral history, its technicl significance and aesthetic significance.Three black / white photographs. 3133.1 shows the approach to a washed away bridge. 3133.2 is of a bridge over a river with men clearing debris. 3133.3 is a close-up showing the wreckage of the bridge.mckillop's-bridge snowy-river flood-damage-1934

McColl Rankin & Stanistreet, North Virginia GM Co NL, Certificate of Boiler Inspection. Certificate that boiler is in good order and may be use up to a pressure of 100 lbs. per square inch. Dated: 23/11/1934. Signed: P Wagstaff, Inspector of Mines Issued by Signature: Samuel ? ?? Makers name A Roberts & Sons. Type Cornish Boiler 25' 6'' x 6' 6'' dia 1/2 plates, 5/8'' ends. Adamson welded flue. 3' 6'' dia 1/2'' plateorganization, business, gold mine, mccoll rankin & stanistreet, north virginia gm co nl, certificate of boiler inspection mines act victoria

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Book - SEC "Workshop Job Requisition" book - numbered 2856 to 2900, three sheets per requisition - yellow, blue and off white kept in book. Has some 20 areas where information on the requisition could be recorded - on the rear sheet is provision for extending the cost of the job and accounting information. The off white sheet has been by the SEC Ballarat track gang to record their daily work, welding, track cleaning, etc for the period 1-8-1950 to 12-2-1951. Appears to be original writing, not a carbon copy. tram, trams, sec, ballarat, depot, trackwork, rails, welding

In October 2000, Council invited three artists from the region (Deborah Halpern, Matcham Skipper, Tony Trembath) to submit designs for a sculpture / public art work for the Eltham Town Square. The commission was paid for by supermarket giant Safeway (Woolies) as part of its supermarket permit, which required them to contribute to beautification work in the Town Square.This is the first of three parts. The 'Spirit of Nillumbik' is a celebration of the artistic spirit of Eltham and surrounding communities. Each area is identified through the flora and fauna represented in the panels. The work honours the many creative artists and architects, past and present, who have built homes and shaped lives and livelihoods with their unique creative spirit. Halpern describes her work as a public expression of their individual and collective visions. Halpern acknowledges these contributions to our hand-made history and the influence they have on the character and identity of Eltham and Nillumbik. Five picture and six woven balustrades each made out of welded steel / organic wrought iron and coated with wax. Imagery (flora - plants, landscapes and fauna - animals, birds, reptiles, insects) are all based on the local environment. There is also a relevant aboriginal presence amongst each of the panels. Each panel represents the different areas that make up the Shire. 'Water' for Warrandyte, 'Kangaroos' for Christmas Hills, 'Cockatoos and 'Valley Creek Flats' for Hurstbridge, 'Wombats', 'Bluetongues' and 'Possums' for St. Andrews/Kinglake, 'Orchids' for Panton Hill, 'Cows' and 'Grapevines' for the Kangaroo Gound Hill landmark. N/Apublic art, nillumbik, fauna, flora, wrought iron, balustrade, halpern, laurence, kangaroo, eltham town square, spirit, warrandyte, christmas hills, kangaroo ground, hurstbridge, kinglake, panton hill, water, valley creek flats, cockatoos

Set of two 35mm Kodak white cardboard colour slide by Keith Kings of: .1 - W2 600 testing the diverted track at St Kilda Jtn. Sunday 10/12/1967. Looking south See Keith's notes as well. Track welding being carried out. Tram showing Special. In the background are signs for Castrol, Speedie Electrical Appliances. .2 - W5 812 and W2 521 on the temporary track following the first diversion for the construction of the new bridge works looking north. Also see Keith's notes. 812 has adverts for wax and Harold's diamonds.Keith Kings stamp and number "14-23" and "14-28"", with details of exposure. .1 - "MMTB St Kilda Jtn bypass works. W2 600 as the test tram after the St Kilda Junction by Pass, No. 1 diversion trying out the south bound temporary track 3.03pm, Sunday 10/12/67. The North bound track tried out at approx. 12.40pm: .2 - "MMTB 521 (route 64 - City) and 812 (route 64 - East Brighton and Malvern Burke Road) on temporary track at St Kilda Jtn bypass. Note sharpness of curves and very limited transitions and tangents. Looking north. 10/12/1967trams, tramways, st kilda junction, trackwork, road works, w2 class, w5 class, route 64, east brighton, tram 600, tram 521, tram 812

The Ballarat Junior Technical School was a division of the Ballarat School of Mines, and a predecessor institution of Federation University Australia.Ballarat Junior Technical School Teacher's Timetable .1) G.B. Pyke (Carpentry, Joniery, Building Construction .2) G.B. Pyke (Carpentry, Joniery, Building Construction .3) R.C. Morgan (Joining, handrailing, building construction, building Technical Maths) .4) James Bell (Toolmaking, Milling and Gear Cutting, Maths, Engine Drawing, Applied Mechanics, Metallurgy) .5) James Bell (Toolmaking, Milling and Gear Cutting, Maths, Engine Drawing, Applied Mechanics, Metallurgy, Electrical Welding) .6) R.C. Morgan (joinery, building construction, buillding Maths) .7) R.C. Morgan (joinery, building construction, buillding Maths)ballarat junior technical school, timetable, george brosnan pyke, robert charles morgan, james bell, trades, building

Book - green Rexene covers, with title - "Melbourne and Metropolitan Tramways Board - Works Codes and Instructions". Six sections, sewn into covers, dated April 1961, signed by J. J. Fisher, Civil Engineer. 118 pages plus covers. Book numbered "46". Provides an list of contents, giving provisional codes or instructions for works, instructions, about the maintenance and repair of the track welding, safe working, watchmen, care of lamps, and plant. 2nd copy added 5/5/2019 from donation of Barry Brooks ex Bob Prentice Collection. Images revised - jpgs removed and pdf added.Inside front cover has a signature and date of 9/8/61 in ink and inside rear cover "not entered" in pencil. Could be a reference to a Court document - see Reg item 94.trams, tramways, mmtb, track, maintenance

A blowtorch or blowlamp is a fuel-burning tool used for applying flame and heat to various applications, usually metalworking. Early blowlamps used liquid fuel, carried in a refillable reservoir attached to the lamp. Modern blowtorches are mostly gas-fuelled. The blowlamp is of ancient origin and was used as a tool by gold and silversmiths. They began literally as a "blown lamp", a wick oil lamp with a mouth-blown tube alongside the flame. This type of lamp, with spirit fuel, continued to be in use for such small tasks into the late 20th century. In 1882, a new vaporizing technique was developed by Carl Richard Nyberg in Sweden, and the year after, the production of the Nyberg blow lamp started. It was quickly copied or licensed by many other manufacturers. Carl Richard Nyberg (May 28, 1858, – 1939) was the founder of Max Sievert’s Lödlampfabrik, then one of the largest industries in Sundbyberg, Sweden. After school he started working for a jeweller and later he moved to Stockholm and worked with various metalworks. 1882 and set up a workshop at Luntmakargatan in Stockholm making blowtorches. However the business didn't work well because it took too long to both manufacture and sell them. In 1886 he met Max Sievert (1849 - 1913) at a country fair and Sievert became interested in Nyberg's blowtorch and started selling it. In 1922 the company was sold to Max Sievert who continued to own it until 1964 when it was bought by Esso. The blowtorch is commonly used where a diffuse high temperature naked flame heat is required but not so hot as to cause combustion or welding: soldering, brazing, softening paint for removal, melting roof tar, or pre-heating large castings before welding such as for repairing. It is also common for use in weed control by controlled burn methods, melting snow and ice from pavements and driveways in cold climate areas, road repair crews may use a blowtorch to heat asphalt or bitumen for repairing cracks in preventive maintenance. It is also used in cooking; one common use is for the creation of the layer of hard caramelised sugar in a crème brûlée. A brass blowtorch, 'Sievert' with a wooden handleSIEVERTtools, blow torches, blow lamps, welding, brazing, jewellery, cookery, soldering, nyberg carl, sievert max, stockholm, sweden, spirit fuel, kerosene, gas fuel, moorabbin, bentleigh, cheltenham, market gardeners, pioneers, early settlers, plumbing, carpenters,

Before 1908 the words "melting pot" was a term relating to a "crucible" with a meaning of "a pot in which metals and other substances are melted (fused) to provide metal items of varying shapes and uses. From the mid 1900's this term changed and became more related to the "mixing" of social and ethnically diverse populations. The description used here is that of pre 1908. This melting pot was used in the early to late 1900's when produce and hardware shops were too far away from the Kiewa Valley and time was at the essence. The ability to manufacture as many "crucial " items at the home property was the difference between running a successful rural business or not. The isolation of the Kiewa Valley (before the 1950's), hindered the "time down" of machinery and important "widget" replacements. The ability of self sufficiency on properties is still a boon to rural properties as time lost is never really recovered.This melting pot is highly significant to the Kiewa Valley as it provides evidence that the graziers and cattle stations required to be self sufficient in all aspects of day to day maintenance and replenishment of worn materials requiring to be "manufactured " at the property and lack of replacements from commercially shelved products. This aspect of "survival" in the "bush" can be seen in the "huts" built on the Bogong High Plains to accommodate the seasonal grazing of cattle from the Kiewa Valley.This black melting pot is made of cast iron. The lid is missing. The top rim of the pot has three lips for poring accuracy. The formation of these lips are in a "triangle" formation. The top section of the body has a curve inwards reducing the pot diameter from 270mm at the base to 135mm.at the top. The handle is made from heavy gauge wire which is fastened to the body through two lugs (welded onto the top section of the pot) and fasten through a hole at the top of each lug. The handle has a "U" shape as it goes through the lug hole, ensuring no accidental fixture to any side thus allowing free swiveling from one side to the other . "BH" indented within a diamond shape. Opposite "No 3"camp fire cooking utensils, hot plate, cast iron cooking appliance, drovers kitchen

This item wasused before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength. This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) within the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools was and still is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron, hand operated Auger has a short barrel shaped cylinder at one end (known as the "Eye") and at the other end a Helical screw blade (screws the cutting edge into wooden material, thereby creating a hole 3/4 inch diameter in the wood) . The barrel section at the top permits a metal or wooden leverage plank to be inserted. The main rod has a 180mm long cutting/screw blade running from the bottom up towards the "eye" end. From the end of the screw blade to the handle is 380mm and cylindrical, but this changes at 550mm from the "eye" end to a 14mm x 10mm rectangular shape shaft.This shaft end is welded to the "Eye".On the shaft below the "eye" is stamped " MATHESON GLASGOW" on the front side and a spade (cards) symbol on the back.auger, hand drill, fencing, tool, rural trades, brace & bit

This item was before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength.This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) of the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron hand operated drill, has a short barrel-shaped cylinder, known as "the eye" welded across the main rod and is 30mm in circumference. It also has a hole drilled to allow a screw to be fastened onto the hand stock ( not available).The main rod is solid for 400mm and then has been flattened and coiled (Helical screw blade) for another 200mm. At the end of the larger screw blade there is a smaller gauged starter blade with a pointer thread 15mm long. This Auger produces a 1/8th inch hole (metric measurement not used at time of manufacture) See KVHS 0469 for 3/4 inch hole and KVHS 0471 for another 1/8th inch hole.A number 5 stamped on the flat sideauger, hand drill, fencing, tool, rural trades, brace & bit

This item was before diesel, electric and battery drilling apparatus were used by farmers, and other trades requiring a portable yet reliable method of drilling holes. As this item is a 3/4 inch hole drill it would be suitable for fencing and providing holes for structural studs. As with all outdoor farm equipment, man power was required (be it the farmer or farm hands). Fitness of the operator was at a high standard but protective gloves were not highly thought of as it was before occupational, health and safety regulations became mandatory over all manual handling activities, be they on rural properties or town/city factories. This period was one where the male ego was at its pinnacle i.e. the harder the tasks the more of a man was required. Hard manual work was not only the "way to go" but also a necessity. Evolution of cheap portable electric/battery powered tools opened up a more efficient method available, especially to those with less muscle strength.This item personifies the rugged environment of the rural workplace. The Kiewa Valley with its main emphasis on farming and grazing provided ample opportunity to use this construction implement. The manufacturer being a Scottish tool company is very significant in the era when this hole maker was in high demand. British steel products were of high grade and had a good record of reliability. The reliability of any tool was a solid factor for farmers and tradesmen in this semi-isolated region (Circa early 1900s) of the Kiewa Valley and its regional area. This factor,although not as crucial, post 1960s, when Asian manufacturers entered the market place and produced cheaper tools and transportation and supplies was more frequent and reliable, the need for the more expensive British made tools diminished considerably. After the influx of tradesmen from war torn Europe (post 1945) and the increased availability of tradesmen in the Kiewa Valley and its region the price of tools is not as crucial and the cost of all required tools has become a minimal part of the equation. It is only with the emerging younger trades person, farmer and grazier, who have more, "one eye on production costs" and no "old ties to the motherland" inert mind set that quality tools such as this auger and other hand tools "must be made to last a life time" is no longer part of the modern work environment.This cast iron hand operated drill, has a short barrel-shaped cylinder, known as "the eye" welded across the main rod and is 30mm in circumference. It also has a hole drilled to allow a screw to be fastened onto the hand stock ( not available).The main rod is solid for 400mm and then has been flattened and coiled (Helical screw blade) for another 200mm. At the end of the larger screw blade there is a smaller gauged starter blade with a pointer thread 15mm long. This Auger produces a 1/8th inch hole (metric measurement not used at time of manufacture) See KVHS 0469 for 3/4 inch hole and KVHS 0470 for another 1/8th inch hole.auger, hand drill, fencing, tool, rural trades, brace & bit

The first sculpture awarded the Shire of Eltham 'Art in Public Places' Award/Commission. The Judges were Inge King, Jenny Zimmer and Daryl Jackson. The work deals with the juxtaposition of suburban and rural surroundings. This scupture is a typical example of the artist's oevre of the period. This sculptre is site specific and refers to the nature of the environment. The colour - bushfire red / sienna - alludes to the history of fire in the urban/rural fringe and the title, as well as the sculpture's shapes, forms and material refer to the natural and local elements. Judges report noted: "The most vital and expressive work for the site...with a great sense of dynamic movement and vibrant colour. Its' abstract forms will enliven the surroundings and the urban and natural environment. This work is the most appropriate for the site and expressive of the dynamics of an evolving community in which artistic discourse and debate has always thrived." The work has acquired the status of a major landmark from the National Trust. The Breeze is an abstract work made out of welded steel and painted in enamel in bush fire red / sienna. It comprises a series of flat, cut-out shapes, interlocking at different angles, giving the impression of being hinged together rather than fixed. The work references nature and the built environment. Its geometric shapes suggest man-made structures within industry and suburban life, while rural areas can be identified by the organic flame-like shapes fanned by the wind. The circular cut-out in the eye mimics the sun, symbolising the intense heat of the Australian climate, while the colour red alludes to the history of bushfire within the urban and rural fringe. N/Apublic art, ginger, red, sienna, elements, steel, abstract, breeze, fire, sculpture

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Collins Australian Diary, 1969, No. 324 printed by Collins Bros, dark red card covers, sewn sections with ruled sheets providing a diary for 1969, one week per double page. Has "useful information" sheets at from the diary. Used by the SEC Ballarat track gang to record their daily work, leave, welding, track cleaning, truck driver etc. Names of gang often mentioned in the diary undertaking specific jobs and when on leave. Loose contents 27/7/1969 - on the back of a Allocation of time sheet for E.C. Fish, a list of names and leave commencing and finish dates. Fish Clough Wiseman Vermeend Denbaden?tram, trams, sec, ballarat, depot, trackwork

In Australia, the wholesale druggists Fenton, Grimwade and Company, established in 1876, were producing small quantities of oxygen for medical and industrial purposes(11,11). In 1910, they produced a booklet promoting the therapeutic use of oxygen, suggesting it's use in pulmonary and cardiac affections, asphyxia, and morphine poisoning(9). Eventually, oxygen was to play a more significant role in medicine following two significant events. In 1895, Karl Von Linde succeeded in liquefying air, and then fractionally distilling its individual components, including oxygen. This new technique for the production of oxygen from air was revolutionary, but large demand for it did not develop in the wider community until Claude and Hess managed to compress acetylene into cylinders safely in 1897, keeping the highly explosive fuel stable by dissolving it in acetone. By 1900, the oxy-acetylene welding technique was born, and the demand for oxygen for industrial purposes accelerated worldwide. In Australia, Russell Grimwade, working for his father's company, ordered the first oxygen plant to be built in Australia in 1910. (George Kantianis, 2013)Medium sized black coloured cylinder with rounded base once containing oxygen with a large black on white diamond shaped manufacturer's label adhered to the front. Much of the label has been degraded with missing bits, and rust stains.Printed on to manufacturer's label: OFFICIALLY PREPARED FOR MED? / AUSTOX [in logo] / COMPRESSED / OXYGEN / CONTENTS / 33 [handwritten in pencil] Imperial Gallons / KEEP COOL / Australiand Oxygen and Industrial ? / Pty. Ltd. / MELBOURNEoxygen, cylinder, therapeutic, russell grimwade

Series of 15 black and white photographs of the track works to reconstruct tram lines showing various methods and works during the 1960's. .1 - Jackhammers concrete out around wooden sleepers - the rails have been bolted to them. .2 - Excavated track or temporary track next to newly relaid track - Hawthorn Road by Caulfield Park? .3 - Partly completed work - nearest track relaid, second track still has wood blocks? and then a temporary track. .4 - Excavated previously concreted and bolted track. Appears to be new rail. .5 - Compacting a new track bed with work laying track in the background. .6 - Rail being craned into position onto small concrete blocks - Nicholson St North Fitzroy at Church St - the church is now Melbourne City Mission Palliative care centre. 1955/56 - construction of the replacement track. Note the Hail bus stop sign on the corner. .7 - Thermite welding being set up. .8 - after a Thermite welding joint completed. .9 - track reading for pouting concrete, with a rebuilt track alongside and temporary track on the other side. .10 - ditto .11 - Concrete being poured .12 - ditto - could be Maribyrnong Road bridge replacement. .13 - Screeding off the concrete - possibly Nicholson St North Fitzroy .14 - completed surface - location as above .15 - completed surface with cloth covers to assist the concrete being cured. Has a MMTB hut and two worker amenity buses alongside. - location as above.Some photos have pencil marks on rear.trams, tramways, trackwork, rails, track materials, track repairs, sleepers, equipment, concrete, welding, nicholson st, new tramway, buses

Set of five colour photographs of the repair of northern end of Wendouree Parade. Photos taken on 5 and 6/4/2003, printed on AGFA paper. 2557.1 - The general scene with the new kerb and channel on the north side - backfilling around the sleepers 5/4/03. 2557.2 - Packing between the sleepers, Len Millar, Sam Boon and Richard Gilbert 5/4/03. 2557.3 - Welding track bonds - Paul Mong 6/4/03 2557.4 - Packing the broken joint area - Simon Green, Alan Snowball, Gary Wood, Bryan Hill, Paul Mong and Peter Winspur with No. 8 in the background. 6/4/03. 2557.5 - Testing the track with No. 8 - Garry Wood and Sam Boon.trackwork, wendouree parade, track, tram 8

Tramcar component - possibly locking key - made from two pieces of cut steel and welded together and finished. A known unknown! Kym Smith advised - "11/6/2020 - It looks familiar, but I can’t recall exactly. I think is used as a locking pin to hold an internal panel in place, possibly the internal panels/frames that are on the interior side of the sliding doors, with the pin going through the top sill into the internal frame?" and 13/6 " I remember somewhere seeing a panel that has pins in the bottom that locate in holes in the floor, then the panel is pushed into place and the securing/locking pin used to hold it in place, with the panel having a square saddle that the pin goes through. I’m wondering if it is a kick panel under a seat? "trams, tramways, tramcars, components

A C-clamp or G- clamp is a type of clamp device typically used to hold a wood or metal work-piece, and often used in, but are not limited to, carpentry and welding. These clamps are called "C" clamps because of their C shaped frame, but are otherwise often called G-clamps or G-cramps because including the screw part they are shaped like an uppercase letter G. The fixed end is not adjustable so size is not variable. G-clamps are typically made of steel or cast iron, though smaller clamps may be made of pot metal. At the top of the "G" is usually a small flat edge. At the bottom is a threaded hole through which a large threaded screw protrudes. One end of this screw contains a flat edge of similar size to the one at the top of the frame, and the other end usually a small metal bar, perpendicular to the screw itself, which is used to gain leverage when tightening the clamp. When the clamp is completely closed, the flat end of the screw is in contact with the flat end on the frame When used some other object or objects will be contained between the top and bottom flat edges. A steel 'G' Clamp tools, g clamp, screws, steel, clamps, metalwork, woodwork, carpentry, early settlers, pioneers, market gardeners, moorabin, bentleigh, cheltenham

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Collins Australian Diary, 1968, No. 324 printed by Collins Bros, dark red card covers, sewn sections with ruled sheets providing a diary for 1968, one week per double page. Has "useful information" sheets at from the diary. Used by the SEC Ballarat track gang to record their daily work, leave, welding, track cleaning, truck driver etc. Names of gang often mentioned in the diary undertaking specific jobs and when on leave. Loose contents April Cash Account sheets 1. - Envelope addressed to Mr. H. Smith - Track Foreman 2 - 3 Number SECV Daily Time Sheet - Day Shift, form FTK 4-60. 26/5/1968 - blank Statutory declaration form for sick leave from the SECV.tram, trams, sec, ballarat, depot, trackwork

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Invicta Australian 1957 Business Diary, No. 4, printed by Sands and McDougall, light brown Rexene binding, card covers, sewn sections with ruled sheets providing a diary for 1957, one week per double page. Has "useful information" sheets at from the diary. Used by the SEC Ballarat track gang to record their daily work, leave, welding, track cleaning, truck driver etc Rear pages - has notes on materials used. Loose contents 1 - 18/11/1957, note dated 26/9/57 to track foreman re work at the Cooling Tower, B station. 2 - 23/12/1957 - envelope address to H. Smith Tracks - with Yallourn Briquettes sales department logo and address details. 3. - Inside rear cover - plan of hospital corner - showing plan of broken joints? tram, trams, sec, ballarat, depot, trackwork, rails

Photo - see pdf file for further information. Number Brief Description CC271 Y1 610 and another at Camberwell depot CC272 Ditto CC273 Y1 613 at Batman Ave CC274 Y1 611 Peel St North Melbourne CC275 Y 469 Camberwell depot CC276 Ditto CC277 Postcard – L104 – MMTB CC278 L103, Hawthorn Road CC279 L103, Hawthorn Road CC280 L103 Dandenong Road CC281 L103 and w5 847 Dandenong Road CC282 L104 on Preston Workshops traverser CC283 Flinders St station with Ws CC284 Flinders St looking south along St Kilda Road to Shrine CC285 Postcard – Nu Color vue – Flinders St CC286 Postcard – Valentines – Flinders St No. 13 CC287 Postcard – Rose Series – 13595 – has been trimmed CC288 Postcard – Rose Series – 10660 – Princes Bridge and Flinders St yard CC289 Postcard – Rose but has been trimmed of Flinders St CC290 Postcard – same as CC285 CC291 SW6 914 and another car in Swanston St by Flinders St CC292 SW6 903 and bus 436 with Flinders St Station in background CC293 W5 776 at Flinders St Station CC294 W2 596 at Flinders St Station CC295 L101 and W2 Swanston St by Ian Brady CC296 Postcard - Biscay BG 250 – A 281 - CC297 W5 779 Maribyrnong River CC298 SW5 787 Queensbridge St CC299A Duplicate copy CC299 Ditto CC300 W5 812 St Kilda Junction CC301 W5 721 Carnegie? - CC302 W5 817 Elliot Ave – see also CC150 CC303 CW5 682 CC304 CW5 682 Dandenong Road CC305 SW6 855 Power St Hawthorn CC306 Argus photo same as CC8A CC307 Freight car 19 leaving South Melbourne depot CC308 Freight car 19 at South Melbourne depot CC309 Cleaner 7 CC310 W2 295 and 8 at South Melbourne Depot CC311 Cleaners 5, 8 and 7 and S or T at South Melbourne depot CC312 Freight car 17 with crew member CC313 Cleaners 5, 8 and 7 along with a tower truck and another road motor CC314 Wheel Transport car 16 at Preston CC315 Cleaner 7 CC316 Cleaner 6 Brunswick Depot R Hudson and Bob Prentice CC317 SW6 867 in Swanston at Flinders CC318 SW6 850 at Chapel and Brighton Road CC319 SW6 914 at Batman Ave CC320 SW6 963 and W5 826 in Collins St near Spencer St CC321 Sw6 923 RAAF tram CC322 Same image at 318, but better has initials T McC (Tom McCaw) CC323 Sw6 963 In Collins at Spencer St CC324 SW6 947 in Collins at Spencer St CC325 Ditto with crew CC326 SW6 850 at Preston Workshop – Argus photo CC327 SW5 843 at Swan and church, severely derailed – Herald photo CC328 SW6 886 in Victoria Parade near La Trobe CC329 SW6 948 turning from Union St into Maribyrnong Road – single curve CC330 W5 731 CC331 SW5 on a 4D – Herald WT photo CC332 Sw6 867 Swanston St with driver carrying handles etc CC333 SW6 954 – Truganini Cres CC334 SW6 915 illuminated for Christmas, the CDA father Xmas special CC335 SW6 850 on route 77 side on view CC336 Sydney R class 1845 on trailer in a busy road CC337 Sydney R class 1845 on trailer CC338 Ditto CC339 Ditto – on trailer turning from a local street CC340 MMTB Emergency van CC341 Ditto CC342 Welding truck – Hopkins and Leeds CC343 Welding truck – Hopkins and Leeds CC344 Welding truck in Hopkins St Footscray CC345 Negative – Hobart tram 103 CC346 Launceston tram CC347 Trackwork – East Kew CC348 Trackwork and a W2 East Kews CC349 SW6 892 and trackwork – East Kew CC350 W4 670 – FRONT ON CC351 W3 654 – Brunswick Depot CC352 W3 666 – St Kilda Road and High St Demonstrates the work of Charles Craig in photography and collection of prints.Assembled album in a black presentation folder of 80 photographs from the Charles Craig Collection - 31 sleeves - part 2 of 2. All photographs have been scanned and placed on the Museum's G drive. A list of all photographs with details where possible has been compiled. Victorian Provincial, Launceston, Hobart and Sydney tram photos have been transferred to other Museums, image files retained.melbourne, tramways, tramcars, trams, charles craig

Set of thirteen colour photographs of the repair of the broken joint in Wendouree Parade as part of the track works in the area. Photos taken on 15 and 16/3/2003, printed on AGFA paper. 2555.1 - Gary Wood, Oedf Byslma looking at the excavated area, with sleeper cutting going on in the background. 2555.2 - Gary Wood and Alan Snowball, cleaning rails and the area, shows status, which was tight to gauge. 2555.3 - Removing sleepers. 2555.4 - First sleeper installed. 2555.5 - Cutting sleepers to length - Rolf Jinks and Andrew Mitchell. 2555.6 - Installing sleepers. 2555.7 - All 4 new ones positioned. 2555.8 - Cutting bolts from old plate. 2555.9 - Bending the rail. 2555.10 - Tram 33 at the temporary terminus. 2555.11 - Rail repositioned. 2555.12 - Installing the screw spikes - Gary Wood, Alastair Reither, Andrew Mitchell and Alan Snowball. 2555.13 - Welding the plates etc - 16/3/2003 - Alan Snowball.trackwork, wendouree parade, track, tram 33

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Invicta Australian 1952 Business Diary, No. 40, printed by Sands and McDougall, green Rexene binding, card covers, sewn sections with ruled sheets providing a diary for 1952, 2 days and notes for each page. Has "useful information" sheets at from the diary. Used by the SEC Ballarat track gang to record their daily work, leave, welding, track cleaning, truck driver etc Rear pages - has a detail list of locations, depth of grove for both rails, rail type and type of rail, whether old or new. Loose contents 1 - 1/7/1952 page - SEC memo written on two sheets, dated 4/5/1949 regarding track work and a SEC Ballarat envelope with notes on the sheet. 2 - 3/9/1952- notes on a daily time sheet 3 - 14/11/1952 - sheet of lined paper with notes.tram, trams, sec, ballarat, depot, trackwork, rails

Yields information about the track maintenance activities of the track gang in Ballarat, the work they did, notes, names and other information.Collins Australian Diary, No. 324 printed by Collins Bros, dark red card covers, sewn sections with ruled sheets providing a diary for 1966, one week per double page. Has "useful information" sheets at from the diary. Used by the SEC Ballarat track gang to record their daily work, leave, welding, track cleaning, truck driver etc Loose contents With the Engagements 1. - part of a card with roses on it 2. - sheet of paper with tramways account numbers on it 3 - Phillips Electrical Pty Ltd -warranty certificate and envelope 4 - Trams out from depot and Mileage Run sheet with notes on the back (Item Reg. 3706) re track measurements. 25/12/1966 - blank weekly timesheet. Inside rear cover - sheet of paper with names and leave owing details. Names are: Lancaster Wiseman Mark Lakey Edwards Fish Donovan Weightman Wilson Rose Mason Scicluna Smithtram, trams, sec, ballarat, depot, trackwork, rails, scrubber tram