Possibly ex Victorian Railways Newport workshops Supplied by Bevan & Edwards Machinery Merchants, Melbourne Sebastian Lathes Described by its makers as the Utility School, Garage and Repair-shop Lathe, the machine immediately below, a Sebastian 15" (circa 1910 - 1926) was the Company's cheapest offering and, in its basic form, lacked a compound slide rest, the tailstock did not set over for taper turning and the bed lacked a gap. However, a friction-type countershaft unit was included in the price as well as a tool post, faceplate, drive plate, changewheels for screwcutting and a small tool kit. As with modern cars (especially BMW) everything worthwhile was on the options' list and by spending more it was possible to specify all those small but important extras. Although in its lowest-cost form this model was reduced to the fundamentals required for a useable, screwcutting centre (engine) lathe it was still reasonably specified and would certainly have fulfilled many requirements when installed in a school or training workshop. The true swing was 15.25", it was properly backgeared and screwcutting was through a conventional tumble-reverse mechanism that allowed both left and right-hand powered movement to the carriage by altering the position of just one lever. As standard it accepted 40" between centres, but any capacity could be ordered, in foot intervals, up to a maximum of 88" - when it is hoped that a central bed support might have been included …… The spindle, which ran in white-metal bearings, had a useful 15/8" hole and a No. 3 Morse taper centre. Some models appear to have had the leadscrew clasp-nut lever on the right-hand side of the apron, while on others it was positioned to the left.. Early Sebastian 13-inch lathe Typical of the Centre or "Engine" lathe made by many manufacturers from the late 1800s until the late 1930s, the basic flat-belt drive Sebastian, with separate countershaft, was eventually relegated to the economy end of the Company's range by the introduction of geared headstocks and self-contained motor-drive systems.Historic - Industrial Machinery - Gap Bed Lathe - Possibly ex Victorian Railways Newport workshops - Purchased and supplied from Bevan & Edwards Gap Bed Lathe - Grey with raw steel parts and a timber cupboard with gears and tools. Bevan & Edwards PTY,LTD Machinery Merchants Melbourne (possible government tag) 365bevan & edwards pty,ltd machinery merchants melbourne, puffing billy

10 NU Louvre Van - Louvred Truck (11) Untrafficable NUU LOUVRED TRUCK. Seven louvre vans for carrying general goods were built during 1899-1901, with another one in 1906 and a further six in 1911, a total of 14 louvre vans numbered 1-14. The term Louvred Truck describes the sides which consist of fixed louvres for ventilation. The aim was to keep the goods inside cool. VR Service History : *NUU 10.VA - 30/12/1911 NWS Built new - / /1926 - To NU 10.VA - NU 10.VA - / 5/1926 - Modified AC Malco /12/1972 BEL To NW 10.VA Sec72/3400, RS72/9371 NW 10.VA - 26/ 8/1976 CLS Photograph #662.2-.4: and end detail 1/10/1977 - Off Register To ETRB Sec76/3630 RS77/4223 Build Date: 30/12/1911 NWS Built new Victorian Heritage Register (VHR) Number H2187 NW 10 is a 1972 reclassification of NU 10. It is presumed the van was used to store tools and equipment. In 1977, the van was removed from railway records and control handed to the Puffing Billy group.Historic - Victorian Railways Narrow Gauge - Rolling Stock - Louvered Van Victorian Heritage Register (VHR) Number H2187 Puffing Billy Locomotives and Rolling Stock CollectionWooden Louvered Van - Made of Timber on a Wrought iron frame - current condition Untrafficable10 NU puffing billy, louvered van, 10nu, victorian railways, 2'6" gauge, narrow gauge rolling stock

Circa 1920s petrol driven cross saw. It was mainly used cross cutting felled logs The Land on which the Menzies Creek railway station and Museum are built on was once apart of James Hermon's & his son William Hermon's property on which this Drag Saw was used. reference : Jinkers and Whims: A Pictorial History of Timber-Getting By Jack BradshawHistoric - Industrial Timber working petrol driven cross saw - Drag SawLarge, mechanical saw mounted on a steel shaft connected to tin fuel and water containers. The machine has two large spoked wheels, a rotating Crankshaft and an extended arm/rod attached to a crank and flywheel.New Record puffing billy, drag saw, timber cutting, early mechanical equipment, james hermon & sons, menzies creek, 1920s

Gang Shed Ganger may refer to: The head of a gang of labourers, especially on canals or railways. They were Men who had the job of track maintenance repair and upkeep or construction for sections of the lines. Gang Sheds were used to keep their tools and equipment and Trollys in. The shed houses and protects the historic trolley and tool collection within. loose based replica Victorian Railways gang shed, permanent way building. Gang Shed constructed of timber and corrugated ironpuffing billy, gang shed, kilmore gang shed, victorian railways, ganger, railway track

McEvoy Miners, c1895.Poster on wall, 'SPORTS' and '£170' only visible textminers, mining, mcevoy mine, men, beards, sports, el dorado, eldorado

A tool for shaping wood - to flatten/reduce the thickness of and leave a smooth surface on a rough piece of timber.ALEX MATHIESON & SON / WARRANTED (on guide) SOLID STEEL WARRANTED (on blade) Trademark crescent and starplane, tool

Black and white photograph. Group of 6 men with gardening implements standing and seated on the lawn. Corner of Pavilion on the left and a timber fence behind. On reverse, "1911." students working outside, gardening tools, pavilion

SHAPED WOODEN FRAME WITH SAW EDGE FOR PRUNING TREES OR CUTTING TIMBER. THE FRAME IS REINFORCED WITH METAL RODS THAT ALSO ADJUST THIS PIECE OF EQUIPMENT. ONE METAL ROD ACROSS THE TOPS STABILSES THE FRAME, ANOTHER ON AN ANGLE BRACES THE CENTRE WOODEN BAR. NONElocal history, trade, tools

Wooden rebate plane - makes square grooves in timber. Flat plane with iron blade inserted through wood.trades, carpentry

Hand forged steel, used for boring holes through timber.rural industry, farm machinery, trades, carpentry

Large metal axe head with wooden handle.rural industry, timber

Coopers tool for making wine barrelsSolid timber arch with a piece of timber slotted through with a metal attachment Wooden handle form which a metal cutting tool extends from

Japanese style box bellows (fukisashi/吹差鞴) reached their current and finalized form by about the sixth century. They are constructed almost entirely of wood and allow a smith to supply a highly controlled air blast to the forge by pulling and pushing the handle slowly back and forth. Using dual chambers and two sets of valves, the air is supplied on both the push and the pull stroke, and the blast may be highly intensified or stopped in an instant as needed by the smith.(http://islandblacksmith.ca/2015/06/why-you-need-a-swordsmiths-fuigo-box-bellows/, accessed 18 February 2018)Timber box with handle on the side which pulls out.fuigo bellows, japanese, bellows, fukisashi bellows, oriental box bellows, pump

An inclinometer measures the angle of inclination of a vessel or aircraft to the horizontalTimber and brass inclinometer from the M.V. Australian Explorer. Triangular timber shape with curved base. Brass measuring plate with measurements from 0-40 degrees on each side. Brass pointer indicates angle of inclination of vessel. 'EIWA' label on front. '87-156' inscribed in pen on back and underside. navigational instruments, australian explorer

These bale measuring rulers were used to calculate bale sizes when loading in ships hold.Obsolete tool is of historical significance to explain past practicesTimber measuring ruler for measuring dimensions of bales being loaded and stacked in ships hold. Outer arms are extendable to suit bale widthsIllegibleinstrument, bale measuring ruler, cargo handling

These shark fishing hooks were collected by Geoff Beasley from QueenscliffFishing artefactsFour shark hooks mounted on a timber board with an embossed labelShark Hooks collected by Geoff Beazleyfishing, shark fishing, hooks, fishing equipment

A hand held tool used for vigorously shaping timber with a blade horizontal to users grip2 Gill Pin....gis? Mill Warranted FAI 27tools, adze, boat building

Wooden mushroom used for darning socks, stockings, etc, timber turned in shape of a mushroom with removable top.handcrafts, needlework equipment, darning

Two white covered auction catalogue with red and black printing for a sale at the Murray Barrages (Mouth of Murray) on 1st to 6th April, 1940. Sale was altered to one week later, the 8th to 13th April, 1940. For sale was Contractors, Engineers & Mining Machinery, Floating Plant, Locomotives, Stores, Buildings and Houses for Removal, Extensive Quantity of Oregon & Hardwood Timber, Scrap Iron, & Valuable Collection of Tools, Equipment & Sundries. Sold under instructions from the Supply & Tender Board, Adelaide. Auctioneers were J. H. Curnow & Son in association with R. E. Jackman & Co. Ltd. Some prices have been written in one catalogue. Black & white photos in the catalogue are: the Goolwa Barrage, Derrick Barge, 'Milang' Dipper Dredge, 'Captain Sturt' Steam Boat and Batter Pile Frame (for pile driving). The tattered copy has Mr. Curnow written in the top left corner. Contains description of some of the machinery.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - murray barrages, j h curnow & son, j l jamieson, r e jackman & co ltd, the supply & tender board adelaide, k p phillips

Pale beige auction catalogue with red and dark blue printing for a sale held from the 31st August to 5th September 1936 at the Hume Reservoir, Albury, (New South Wales Side) By Order of Department of Works and Local Government, N. S. W. For sale was Contractors', Mining and Engineers' Machinery, Plant and Equipment, Stores, Locomotives, Tools, Petrol and Steam Engines, Tanks, Scrap, Building Materials, Heavy Bridge Timber, Buildings, and Workmen's Five-roomed Houses, etc. J. H. Curnow & Son were the auctioneers. Black and white photos include Lots 2065 and 2622 Kelly & Lewis Engine and Condensing Plant with G.E.C. Dynamo, Generating 300 K.W.; Lot 2018 Locomotive; Lots 2617 and 2618 Steam Road Rollers; Lot 2069 Administrative Offices; and Lot 93 Locomotives (Victorian Side).business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - hume reservoir, department of works and local government nsw, j h curnow & son, j l jamieson & co, j b garnsey, a t jones, bolton bros pty ltd

A fid is a conical tool traditionally made of wood or bone. It is used to work with rope and canvas.Fids where traditionally used for working with rope and/or sails on sailing ships. They are still in use today for working with rope.Large timber fid with a metal ring attached to wide end for strength used for splicing rope or cable.fid, sail making, rope splicing

Timber conical shaped fid designed to fit the palm of the hand101-3Nfid, sailmaking, rope making, sailing, marine craft