Fire Fighting Extingusher Tank Old style firefighting extinguisher, for use on very small firesHistoric - Railways Permanent Way and Works - track equipment - Fire Fighting Extingusher TankMetal Fire Fighting Extingusher Tank with rubber hosepuffing billy, fire fighting extingusher tank

This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

Ganger's Fire Beater This was used to beat the flames of a fire. They were used by track Gangers when burning off the trackside vegetation, to ensure the fires were kept under control. the canvis was dampened with water before useHistoric - Railways Permanent Way and Works - track equipment - Ganger's Fire Fighting Mop Ganger's Fire Beater made of timber handle with canvas strips attached puffing billy, fire beater

Light Rail Bender Most rails are produced straight. While they to easily bend and appear flexible, they are required to bend for some curves, at rail joins on curves and at point (turn-out) junctions. For a safe transition around curves and in the finer areas of the point, this use to be done with a manual rail bender. Sometimes referred to as a Buddah, the rail bender attaches its two claws to the rail. In the middle of the two claws is a screw that is slowly tightened using a crow-bar to bend the rail. Tightening the screw too fast or too tightly may not give the structure of the rail time to redistribute and the rail may break if not done properly. Historic - Railways Permanent Way and Works - track equipment - Light Rail Bender Light Rail Bender made out of cast wrought ironpuffing billy, light rail bender

Rail Turning Bar Rail is heavy, sometimes as much as 120 lbs per yard. To assist in being able to move rail, a special turning bar was developed. Usually a long handle, on one end various features in the head allow rail to be moved Historic - Railway Permanent Way and Works - track equipment - Rail Turning BarRail Turning Bar made from cast wrought iron puffing billy, rail turning bar

Ratchet Spanner This spanner is used on track work. Being a ratchet spanner, it allows movement in one direction, with a reverse movement to keep the tool in the same position, but it does not allow the item being tightened to rotate with the spanner in the reverse direction. This allows for longer handles and therefore gives more force to the item that is being tightened or released.Historic - Railway Permanent Way and Works - track equipment - Ratchet SpannerRatchet Spanner made of cast wrought iron puffing billy, ratchet spanner

Watering Can A watering can, with a large spout. Its former use is currently no known, but may have been used for oil, chemicals or even sand.Historic - Railway Permanent Way and Works - track equipment - Watering CanWatering Can with a large spout made of tin puffing billy, watering can

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 92NQR - Goods Vehicle - Open Medium Truck NQ/NQR OPEN MEDIUM TRUCKS. 218 of these goods vehicles were built between 1898 and 1914 numbered 1-218. Originally, these wagons carried the code letter R as they were built with sides and ends. Some later had the R removed if they regularly ran as flat wagons without theh sides and ends. Over the years, a number of NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames. 92 NQR VR Service History : *NQR 92.VA - 2/ 3/1907 NWS Built new - / /1926 - To NQ 92.VA -Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck with drop ends Victorian Heritage Register (VHR) Number H2187 The Puffing Billy Rolling Stock Collection 92NQR - Open Medium Truck with drop ends made of Steel and metal92NQR puffing billy railway, pbr, rolling stock , 29 nqr, narrow gauge rolling stock, victorian railways, nqr wagon

NNN - BALLAST HOPPER, This vehicle was built by the Tasmanian Govt. Railways in 1954 and classified QG. A number were obtained by the Puffing Billy Railway for use on ballast trains but to date, only two have been converted. When the first of these was converted for 2’6” gauge operation it kept the Tasmanian QG but with the addition of an N prefix, and also kept its Tasmanian number of 3. However, to follow traditional V.R. practice, in June 2003 it was reclassified to NNN and numbered 1 as the nearest counterpart on the V.R. was the broad-gauge NN. A second one, numbered 2, has since been converted. 1 NNN - Bogie Ballast Hopper Truck Service History Built 1954 Tasmanian Railways - QR 3 - Bogie Ballast Hopper Truck converted from a 3ft 6 inch (1,068 mm) gauge ex Tasmanian Railways ballast wagon by the Puffing Billy railway. Coupled Length 20 feet 0 inches (6100 mm) Weight 6 tons Capacity 10 tons Number Built Not known In use 1 To be restored 3 Puffing Billy Service History or Notes Historic - Tasmanian Government Railways - 3 QG Bogie Ballast Hopper Truck Puffing Billy Railway - Track maintenance Vehicle - NNN - Bogie Ballast Hopper Truck1 NNN - Bogie Ballast Hopper Truck made of Steel and metal1NNNpuffing billy, pbr, rolling stock , 1 nnn bogie ballast hooper truck, tasmanian government railways, 3 qg bogie ballast hopper truck

NNN - BALLAST HOPPER, This vehicle was built by the Tasmanian Govt. Railways in 1954 and classified QG. A number were obtained by the Puffing Billy Railway for use on ballast trains but to date, only two have been converted. When the first of these was converted for 2’6” gauge operation it kept the Tasmanian QG but with the addition of an N prefix, and also kept its Tasmanian number of 18. However, to follow traditional V.R. practice, it was reclassified to NNN and numbered 2 as the nearest counterpart on the V.R. was the broad-gauge NN. A second one, numbered 1, was also converted. and was reclassified to NNN in June 2003 2 NNN - Bogie Ballast Hopper Truck Service History Built 1954 Tasmanian Railways - QR 18 - Bogie Ballast Hopper Truck converted from a 3ft 6 inch (1,068 mm) gauge ex Tasmanian Railways ballast wagon by the Puffing Billy railway. Coupled Length 20 feet 0 inches (6100 mm) Weight 6 tons Capacity 10 tons Number Built Not known In use 1 To be restored 3 Puffing Billy Service History or Notes Historic - Tasmanian Government Railways - 18 QG Bogie Ballast Hopper Truck Puffing Billy Railway - Track maintenance Vehicle - NNN - Bogie Ballast Hopper Truck2 NNN - Bogie Ballast Hopper Truck made of Steel and metal2NNNpuffing billy railway, pbr, rolling stock , 2 nnn bogie ballast hopper track, tasmanian government railways, 18 qg bogie ballast hopper truck

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 91 NQR - Open Medium Truck VR Service History 15/ 2/1907 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 *NQR 91.VA - 15/ 2/1907 NWS Built new - / /1926 - To NQ 91.VA - Puffing Billy Service History or Notes April 2016 - New Bogie has been assembled and awaits testing under 91NQR May 2016 - New Bogie has been assembled and awaits testing under 91NQR July 2016 - New Bogie has been assembled and awaits testing under 91NQR Aug 2016 - New Bogie has been assembled and awaits testing under 91NQR Sept 2016 - New Bogie has been assembled and awaits testing under 91NQR Oct 2016 - New Bogie has been assembled and awaits testing under 91NQR Nov 2016 - New Fox bogie Under 91NQR - Flats Link to Heritage / Period Photos PBR Workshop Blog Report Friday, May 20, 2016 Bogie in Brief - on NQR 91 http://puffingbillyworkshops.blogspot.com.au/2016/05/bogie-in-brief.htmlHistoric - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck with drop ends91 NQR narrow gauge Open Medium Truck with drop ends made of Steel and metal91 NQRpuffing billy, pbr, rolling stock , 91 nqr, narrow gauge rolling stock, nqr wagon, victorian railways, 91 nqr

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 26 NQR - Open Medium Truck (11) 10/12/1898 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 VR Service History *NQR 26.VA - 10/12/1898 NWS Built new - / /1926 - To NQ 26.VA - NQ 26.VA - 24/10/1936 NWS Into Workshops - 7/12/1936 NWS Out of Workshops (45 days) /10/1954 - Sold (to) - Puffing Billy Service History or Notes Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck26 NQR - narrow gauge Open Medium Truck made of Steel and metal26 NQRpuffing billy railway, pbr, rolling stock , 26 nqr - open medium truck, victorian railways, narrow gauge rolling stock, nqr wagon, 26 nqr, nqr open medium truck

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 103 NQR - Open Medium Truck 16/12/1909 NWS Built new Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 VR Service History *NQR 103.VA - 16/12/1909 NWS Built new - / /1926 - To NQ 103.VA - Puffing Billy Service History or Notes Untrafficable at ClematisHistoric - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium TruckA large rectangualr open good wagon, with removable sides and ends creating a flat-bed. There are three long drop-down sides and eight narrow guage wheels. The wagon is 7671mm long and 1905mm wide with steel couplings at either end. The wagon is painted crimson (faded) with the words '103 NQR' stenciled in white at both ends. 103 NQRpuffing billy railway, pbr, rolling stock , 103 nqr - open medium truck, victorian railways, narrow gauge rolling stock, nqr wagon

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 23 NQR - Open Medium Truck VR Service History - NQR 23.VA - 10/12/1898 NWS Built new - / /1926 - To NQ 23 Puffing Billy Service History or Notes Untrafficable at Emerald Historic - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck 23 NQR - NQR at Emerald - Open Medium Truck made of Steel and metal23 NQR puffing billy railway, pbr, rolling stock , ? nqr - open medium truck, narrow gauge rolling stock, nqr wagon, 23 nqr, victorian railways

The NQRs were the standard Medium open goods wagon. Generally the sides and ends were removable thus providing a totally flat truck. Three long drop-down doors formed the sides thus allowing easy loading and unloading. 218 of these goods vehicles were built between 1898 and 1914 ? numbered 1 - 218​. Originally, these wagons carried the code letter R​ as they were built with sides and ends. They later had the R removed. Unlike the Broad Gauge, VR's 2 ft 6 in (762 mm) narrow gauge network never had four-wheeled wagons (aside from a handful of trolleys). Because of this, a single design of open wagon emerged and this was the only type of wagon ever used on these lines. This was the NQR class, a wagon with the same length and loading capacity as a Broad Gauge four-wheeled open wagon to make transferring freight between the gauges easier. The wagons, numbered 1 through 218, were built between 1898 and 1914. The wagons used the same underframe as most other non-locomotives on the VR Narrow Gauge. Letters and numbers were originally painted only on the end bulkheads and doors, both of which could be removed as traffic dictated, and this made wagon identification difficult until the decals were transferred to the underframes of each wagon In the 1910s some NQRs were provided with removable wood and steel frameworks with canvas roof canopies and side curtains, and internal seating to supplement the rest of the passenger stock during busy holiday periods. Puffing Billy has re-created these for emergency capacity. Five more NQRs, numbered 219-223​, were built between 1990 and 1992 initially for passenger use so were fitted with the removable frames In the 1960s the Puffing Billy Railway added grids in the floor of some to enable them to be used to drop ballast on the track where needed. Vehicle Length 25 feet 2 inches ( 7671 mm) Coupled Length 27 feet 4 inches (8330 mm) Width 6 feet 3 inches (1905 mm) Weight 5 tons Capacity 11 tons Built 1898 - 1915 (1992) Number Built 218 (223) In use 14 To be restored 6 203 NQR at Clematis - Open Medium Truck 203 NQR - Open Medium Truck (11) VR Service History - NQR 203.VA - 5/12/1913 NWS Built new - / /1926 - To NQ 203.VA - NQ 203.VA - / /1973 NWS Stored minus bogies, NR4/73 Puffing Billy Service History or Notes Untrafficable at ClematisHistoric - Victorian Railways - Narrow Gauge Rolling Stock - NQR Open Medium Truck 203 NQR at Clematis - Open Medium Truck made of Steel and metal203 NQRpuffing billy railway, pbr, rolling stock , ? nqr - open medium truck, victorian railways

NWT1 - Jenny - Trolly Trailer Built by Puffing Billy Volunteers named after PBPS member John Thompson's wife Jenny built on the frame of an old casey trolly . previous no. NWTC-1 Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - Trolly TrailerNWT1 - Jenny - Trolly Trailer made of Steel NWT1 - Jennypuffing billy, trolley trailer, trolly, trolley

NG1 - Sarge - Trolly Trailer Named Sarge as it originally had three safety chevrons on the back that resembled Sargeant's stripes.Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - Trolly TrailerNG1 - Sarge - Trolly Trailer made of Steel and MetalNG1 - Sargepuffing billy railway, pbr, rolling stock , ng1 - sarge - trolley trailer, trolley, trolly

Red Trolley - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyRed Trolley - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, red - trolley, bn class trolley, trolley, trolly

Yellow Trolly - BN Class Trolly Class: BN* * Trailers marked (*) are classified as Rail Mounted Tools or Tool Carriers for the purposes of Section 1 of Appendix 1 of the General Instructions. Number: 1, 2 & 3 Name: - Description: Flat top dummy Load Capacity. - Goods : 1 ton (1 tonne) - Persons. ---Puffing Billy Railway - Narrow Gauge Track maintenance Vehicle - BN Class TrollyYellow Trolly - BN Class Trolly - Flat top dummy made of wood and wrought ironpuffing billy railway, pbr, rolling stock , yellow - trolley, bn class trolley, trolly, trolley

NVW 1 - Track Patrol vehicle Rebuilt by Puffing Billy Volunteers given Number NVW 1 as it was built with a (VW) Volks wagon engine Was originally a trolley on the Australian Portland Cement Ltd at Fyansford Victoria Obtained by the Puffing Billy Preservation Society around 1968. Originally 3'6" ( 1067mm) before being rebuilt. Historic - Puffing Billy Track patrol - Rail Vehicle - NVW 1 NVW 1 - Track Patrol vehicle made of metal & steel with canvas vinyl blindsNVW 1puffing billy, nvw 1, trolley, trolly

V.R Fuel Can for Trolley - Victorian Railways Fuel Can for Trolly Motor Spirit Highly Inflammable Transporting Tin Container "Motor Spirit" is just another name for petrol. "K" and the "KS" Kasey Trolleys were two stroke petrol motors Operation, Care and Maintenance of Track Motors Victorian Railways, 1959 http://www.geoffsrailpix.com/Documents/Motors.pdf gives the following : Inspection motor type B, - straight petrol Inspection motor type V, - pre-mixed petrol Motorised tricycle type M.T., - pre-mixed petrol Gang motor type K.S., - pre-mixed petrol Gang motor type K - pre-mixed petrol Motor cars altered for rail uses (Wiki) Petrol Inspection Car This was a small car numbered '1' and named the Inspection Car. It was built in England in 1923, but was not found in the 1936 stocktake. Gang Motor The eight-horsepower Gang Motor held five people, and was built at Arden Street in late 1923. In 1950 the vehicle was removed from the rolling stock register and given to "Way and Works" as a track motor. Motor Car The Motor Car was put into service in mid 1925, after being fitted with rail wheels in lieu of tyres. In 1927 the car was named "Mr Molomby's Inspection Car", and allocated to Seymour. It was scrapped in 1952. Dodge Cars There were seven Dodge cars in rail service. The cars were numbered 1 to 6, with car 7 listed "No 7 Repair". The cars were built by the Dodge Company of Melbourne and assembled at Newport. Construction was in 1925 and they lasted until 1949.Historic - Victorian Railways - Permanent Way and Works - track equipment - V.R Fuel Can for TrolleyV.R Fuel Can for Trolly - Metal Fuel TinMotor Spirit Highly Flammable V.R 8 ?puffing billy, victorian railways, fuel can, trolley, trolly

Rail spike from the Wensleydale rail line. The line ran from Moriac to Wensleydale which closed in 1948 and was dismanatled in 1951. The rail spike is a large nail with offset head used to secure rails and base plates to railroad ties in the track.Nonerailway spike, wensleydale railway, crampon

This is possibly a photograph which records trips made around Victoria of the 'Flying Scotsman' engine which was brought to Australia in late 1980s.A coloured photograph of a steam engine painted blue, black and red travelling under full steam along a rail track.steam engines, the flying scotsman, railways, george evans collection

The photograph was taken when railway land on either side of the tracks was used for recreational purposes and agricultural related activities. The local sports ground is on the RHS of the photograph and was used to stage a number of the town's events.A black and white photograph of a section of the two railway platforms and three sets of rail tracks with a stone bridge in the distance. Four rail carriages and eight goods trucks are on a railway siding near a wheat silo. There is open land on either side of the rail tracks.sunbury railway station, wheat silos, railways, macedon street rail bridge., george evans collection

The bluestone 'road over rail' bridge at Macedon Street is of state architectural, architectural, historical and engineering significance. It spans the first government regional railway. Its design and building was done according to strict English standards and made use of a bridge crossing instead of a level road crossing.A black and white photograph of a stone bridge with an eliptical arch spanning two rail tracks. A workman is standing between one set of tracks in the foreground and a railcart is next to the tracks. The station, footbridge and water tower are visible through the arch.road over rail bridge, bridges, sunbury railway station, water towers, pedestrian bridges, stone bridges, george evans collection

This photograph was taken during the upgrade of the Bendigo Railway line at Sunbury Station. The upgrade of the line took over twelve months to complete and bus services replaced the train service during that time.A coloured photograph of construction on the site of the Sunbury Railway Station. The photograph has been taken from the Macedon Street bridge and is looking south towards Station Street. The old rail tracks have been removed and excavation work is in progress to make way for the new tracks. The new rail lines have been placed on the side of the track on the RHS of the photograph.railways, bendigo line, railway stations, bridges, sunbury railway station, george evans collection

This photograph was taken during the upgrade of the Bendigo Railway line at Sunbury Station. The upgrade took twelve months to complete and during that time bus services replaced the trains.A coloured photograph of construction on the site of the Sunbury Railway Station. The photograph was taken near the Station Street level crossing and is looking north towards the Sunbury Station. The new tracks have been put into place.railways, bendigo line, railway stations, bridges, sunbury railway station, george evans collection

This photograph was taken during the upgrade of the Bendigo Railway line at Sunbury Station. For the twelve months when the upgrade of the line took place buses replaced the train services.A coloured photograph of construction on the site of the Sunbury Railway Station. The photograph was taken from the Macedon Street end of the station platform and shows the excavation taking place to allow for the placement of the new rail tracks.railways, bendigo line, railway stations, bridges, sunbury railway station, george evans collection