Significant in being a detailed set of instructions for the Forest City signalling system that was operated by the tram's trolley pole. Details of the locations and crossing loops where used, primarily around the loop and through Bridge St. and how it operated. Prepared and printed by the SEC during 1965.Five page, foolscap duplicated document, stapled in two locations along the top edge, titled Forest City Signals, and dated 20-1-1965, giving details about the Forest City signalling system installed in Ballarat. Explains how the system operates, gives instructions, details of the system, location of the loops, trams following each other, power failure. Also gives details of how the Bridge St system operated and the switch at Grenville St. Gives instructions for running out of the depot. Note: The locations of the signals are not as detailed as in the Driver Training Manual - See Reg Item 3486 See also Reg Item 5373 for another similar copy and fully scanned copy.trams, tramways, signals, crossing loop, forest city signals, grenville st, wendouree parade

Yields information about the operation of the BTM and the management of tramcar operations. Demonstrates how information within tram crews and shed staff was distributed.Thirty Six page document within grey card covers, folded A4 paper to form an A5 booklet titled "Ballarat Tramway Museum Driver Operations Manual, November 2008". Provides details of the manual, index, details of tramcar equipment, tramcar braking, fault finding and Operating Instructions. Issued to existing workers and new workers at the time. See memo in back of worksheet for Reg item 4440 for details and mailing list.trams, tramways, btm, operations, instructions, procedures, drivers

Yields information about the instructions about Signalling system on Wendouree Parade and Bridge St - Forest City signals.Five page, foolscap duplicated document, stapled in the top left hand corner, titled Forest City Signals, undated, has letters S4 in top right hand corner of first sheet, giving details about the Forest City signalling system installed in Ballarat, particularly around Wendouree Parade and the depot. Explains how the system operates, gives instructions, details of the system, location of the loops, trams following each other, power failure. Also gives details of how the Bridge St system operated and the switch at Grenville St. Note: The locations of the signals may not be not as detailed as in the Driver Training Manual - See Reg Item 3486. Does not provide instructions for Lydiard St North or Sebastopol routes. See also Reg Item 3456 for another similar copy.trams, tramways, signals, crossing loop, forest city signals, grenville st, wendouree parade

The Mowat Sensor model MS 01, is a pale green, palm-sized, plastic battery-operated device with a darker green switch on top. It is partially open at one end with two grilles. A microphone plugs into the other end with a wrist strap. It came with a brown vinyl carry case and owner's manual, which are not included. This handheld device for the visually impaired uses high frequency sound to detect objects within a narrow beam. The sensor vibrates if an object is present, responds to closest object within the beam. The vibration rate increases as user approaches object. There are two range settings: short, responds to objects less than 1 meter away (indoor use) and long, responds to objects of sufficient size up to 4 meters. The sensor can be handheld or carried in pocket or purse. As a facility intended for partially sighted people, the compass also includes an in-built color indicator (visible through the semi-transparent enclosure), which indicates the direction using a combination of three colours. Weight: 185 grams. Comes with dark brown vinyl case.1 pale green coloured plastic rectangle sensor with a brown nylon, plaited wrist strap Model MS01assistive devices, orientation and mobility

A steel manual breast drill with an attached curved flat plate at the top to apply pressure with the chest.. This plate is attached to the drill by a screw. A wooden handle turns the drill mechanism to operate it and a second wooden handle is to steady the operation. It was used for making cylindrical holes by rotation.drills, push drills, hand drills, tools, handtools, breast drills, woodworking tools

Used to measure wind speed at Gabo Island. Max gust register and wind speed indicator were interconnected to anemometor also on display. Registor and speed / direction indicator redundant due to transition to radio transmitter and computer data recorder. This instrument for measuring wind speed by knots was made by Paton Electrical, Sydney, a radio receiving manufacturing firm which operated until c.1956. It was used in conjunction with the manual anemometer. An instrument now redundant to modern weather forecasting, it is a good example of its kind and has first level contributory significance for its historic value and provenance to the lightstation. It is a good example of its kind and has first level contributory significance for its historic value and provenance to the lightstation.Knots wind speed indicator. Housed in a black & grey metal box shaped enclosure. The front is sloped with a guage and indcator dial. Around this are eight clear orange plastic knobs with directions inscribed next to each knob.Around front in clockwise direction,"N/360, NE/45, 90/E, 135/SE, 180/S, SW/225, W/270, NW/315" On dial, 0 - 70's in 10's, "KNOTS WIND SPEED / STOCK No 6660' - 66-118-7294 / PATON ELECTRICAL SYDNEY"

A manual telephone exchange, manufactured by British Ericson, History Originally in use at Cohuna. When Cohuna was converted to automatic dialing this exchange was relocated to Harcourt, to become the third and last in a bank of three exchanges. At this time Harcourt exchange was expanded to 260 lines. It was connected to the district central exchange at Castlemaine. Operated by mains power with battery back-up. Harcourt exchange was operated by Betty McLean, Miss Mitchell, Josie Hogarth, Mr. & Mrs. Heighway, Bill & Valerie Milford, Irene Bolitho and others. Decommissioned approx. 1970. Incoming calls prompted the fall of a shutter. The operator made the connection by plugging the line into the number requested. While responding to calls the operator needed her hands free to jot down the billing particulars or to write out each telegram. Nearby stood pigeonholes with various items of stationary. Many telegrams were received each day, particularly advising fruit growers on interstate markets. Most telegrams were phoned through by the operator. This exchange was restored in 2004 - 2005 by Trevor Grant.. Many people relate to this exchange. It is a survivor of the pre-electronic era when ‘telephonist’ was a common occupation. A vital element in the communications between households and between district orchardists and their suppliers and clients.A manual telephone exchange, manufactured by British Ericson complete with operator hands-free headset/earphones and speaker mouthpiece. Wooden case with one hundred shutters and sockets. Accommodates twelve lines with extension leads with associated switches. Operated by mains power with battery back-up. Decommissioned approx. 1970. Incoming calls prompted the fall of a shutter. The operator made the connection by plugging the line into the number requested. This exchange was restored in 2004 - 2005 by Trevor Grant.

This chainsaw was one of the earliest models sold in Australia. It was manufactured by the Lombard company which was established in 1894 when Nathaniel Lombard developed the first practical water wheel governor in Roxbury, Massachusetts, USA. In 1904, the company moved to Ashland, Massachusetts. During the first World War, Lombard Governor produced hydraulic lathes for the manufacture of artillery shells At the conclusion of the war, Lombard expanded into the areas of chain saws and plastic molding injection machines. This model, the L-30 was only produced for 2 years from 1962 - 1964, primarily due to safety concerns and the fact that it did not have any way to sharpen or tighten the chain. This chainsaw was sold by Mann of Wodonga and donated to the Wodonga and District Historical society by David Mann, owner and manager of Mann Wodonga.This item is significant as it was produced for a limited time. It was also sold by a prominent Wodonga business.A single operator chain saw from Lombard, Ashland, Massachusetts, USA. The chainsaw was relatively lightweight but had no safety features such as a chain brake. It was made primarily of sand cast magnesium. The main cylinder was constructed of aluminium with a cast iron sleeve. It had a manual oil pump, the crankshaft operated on ball bearings and it had a maximum rpm of 4,500. See the Model profile in the accompanying Media item for details.On side of fuel tank: "ONE HALF PINT/SAE-30 OIL/ FOR EACH/ GALLON GASOLINE/ MIX WELL IN SEPARATE CONTAINER/BEFORE FILLING" On opposite side: "STARTING INSTRUCTIONS 1: FILL FUEL TANK WITH PROPER FUEL MIXTURE ( AS NOTED ON TANK) 2. FILL OIL RESERVOIR WITH #30 MOTOR OIL 3. CLOSE CHOKE, MOVE LEVER BACK TOWARDS AIR FILTER 4. HOLD THROTTLE WIDE OPEN 5. PULL STARTER HANDLE SLOWLY UNTIL STARTER ENGAGES, THEN GIVE IT A SHARP YANK 6. AS ENGINE WARMS UP, EASE CHOKE LEVER TO OPEN POSITION"hand tools, vintage chainsaws, david mann, mann wodonga

3 Volumes of information to Victorian Railways Goods Rates under a range of categories. They have blue board covers and had cloth binding. Print on the cover and throughout the books is in black ink. Much of the information is in tabulated format.These 3 volumes were issued by the Victorian Railways to all railway stations outlining changes made to goods and freight rates to operate in Victoria as of 14th February 1966. They were significant publications as they itemised the first rates after the introduction of decimal currency to Australia.victorian railways, victorian railway rates

A blue covered document published on white paper outlining changes to rates on Victorian Railwaysnon-fictionThis is a manual issued by the Victorian Railways to all railway stations to outline changes made to passenger and freight rates to operate in Victoria as of 14th February 1966. These changes were significant as it itemised the first rates after the introduction of decimal currency to Australia.victorian railways, victorian railways -- rules and practice., public transport victoria, victorian railways fares and rates

A booklet with a red cover and black print. There are extensive instructions on the cover which include distribution details and dates on which these instructions came into effect,fictionThe Public Transport Corporation (PTC) was a Victoria State Government owned statutory authority formed under the Transport Act 1983 which operated passenger and freight trains, trams and bus services. It was established on 1 July 1989. This memo was effective as from Sunday 16th May, 1993 and pertained to rules instructions and operating procedures regarding air brake equipment and train examination requirements. As noted on the cover: "Part One - Supersedes Automatic air brake rules, pages 479-495 of Book of rules and regulations. -- Part Two - Supersedes Air brake orders, pages 189-198 of General appendix." The cover bears the signatures of M. Digging, Safeworking Superintendent and G. De Bont, Group Manager, Freight Fleet Maintenance.locomotive manuals, victorian railways, public transport corporation victoria, victorian railways -- rules and practice.

A collection of 5 manuals for a range of Clyde Diesel Locomotives. The collection includes instructions for the Clyde G8B, G16C, G26C, 1800 HP Model A and the Clyde Mailiner Model 2. On the cover of each manual, the owner has written the letter for the name of class which the relevant locomotive was ascribed in Victoria. The Clyde Engineering Company Limited was registered on 30 September 1898 in New South Wales. It was one of the iconic Australian engineering firms whose history spanned just over a century and was one of the few locomotive and rolling stock builders in the world that transitioned from steam to diesel to electric traction. The company was formed by Walter Maplesden Noakes who purchased the works of Hudson Brothers Limited in the Sydney suburb of Granville, which had been established by in 1882. The manuals refer to the following locomotives:- Clyde Model G8B which operated in Victoria as the new T class locomotive. It was introduced in 1955 and was the most numerous class of diesel locomotive used in Victoria. This model continued in operation until 1968, although many were modified for continued service. Clyde Model G16C, later superseded by the G26C operated in Victoria as the X class locomotive between 1966 and 1976. Clyde Model 1800HP Model A became the S class locomotives in Victoria. Additional numbers were purchased in preparation for the opening of the standard gauge line between Melbourne and Albury, They entered service between 1957 and 1961. Clyde Mainline Model 2 became the B class in Victoria. The B class were the first mainline diesel-electric locomotives in Victoria entering service in June 1952. They were initially used on the main passenger and freight services, before moving out to other areas. They remained in service until the early 1990s.fiction This collection of Diesel Locomotive Manuals was published by the Clyde Engineeringclyde engineering, diesel locomotives, locomotives victoria

A small manual with red cloth board cover and black printnon-fictionThis is a manual issued by the Victorian Railways to all Diesel Locomotive drivers. Every driver was required to be conversant with and follow the instructions. The book had to be carried by the driver when on duty and to be produced on request. Diesel locomotives were introduced into Victoria from 1955 onwards.railways victoria, railways victoria handbooks and manuals, diesel locomotives

A collection of Locomotive operation manuals. All are paperback and feature an image of the relevant locomotive on the cover. Relevant illustrations are included in each publication. Cover is of card and they are bound with staples.fictionThe manuals refer to the following locomotives:- Westrail L Class (November 1983) originally built by Clyde Engineering from 1967 for the Western Australian Government Railways (WAGR) for use on the Eastern Goldfields Railway between Perth and Kalgoorlie. In 1983, three were leased to V/Line to haul services on the standard gauge Melbourne to Albury line, sometimes extending through to Sydney.A class (January 1984) were initially used for "Intercity" passenger services within Victoria. In this service, they operated at speeds up towards 125 km/h. Later, they were also used for freight services.N class (September 1985) produced by Clyde Engineering and entered service in 1985 and still operating in 2023. 422 Class diesel-electric locomotives (August 1983), designed by Clyde Engineering were introduced in January 1969. Following crew training, the engines entered service on the Main Southern line between Sydney and Albury and the Illawarra line from Sydney to Port Kembla and Moss Vale. Among the passenger services they hauled were the Southern Aurora and the Spirit of Progress. From 1982, they began to operate through to Melbourne. This ceased in February 1990 when non-air-conditioned locomotives would no longer be accepted by Victorian drivers.railways victoria, diesel-electric locomotives

2 booklets documenting Union regulations for railway employees, the 1979 publication on green paper and the 1987 publication on buff coloured paper. Both have staple binding on the spine.fictionThese handbooks document changes in industrial awards put in place to regulate the work conditions and safety in the railways. The 1979 Information Handbook was issued by the Central Council of Combined Railway Unions. The 1987 publication by the Australian Federated Union of Locomotive Enginemen outlined the Locomotive Operating Grades Award as implemented by the Victorian State Transport Authority.vline safety, vline training, railways victoria, australian federated union of locomotive enginemen

2 small publications outlining changes to existing regulations. Both bear the logo of the Victorian Public Transport Corporation and are printed in black ink.fiction These booklets outline changes to regulations governing rules and operational procedures of Victorian Railways. The white booklet outlines Supplementary Rules and regulations Amendments for the operation of locomotive hauled driver only passenger trains in 1992. The pink booklet is a guide to the 1994 book of rules and operating procedures. It included major changes with respect to existing safe working policy so was a critical document issued to all staff to be read in conjunction with the full book of rules. vline safety, vline training, railways victoria, public transport corporation victoria