This wagon wheel spoke was recovered from the wreck of the Falls of Halladale. Buggy wheels and spokes here amongst the varied cargo carried on the ship. The Falls of Halladale was an iron-hulled, four-masted barque, used as a bulk carrier of general cargo. She left New York in August 1908 bound for Melbourne and Sydney. In her hold was general cargo consisting of roofing tiles, barb wire, stoves, oil, and benzene as well as many other manufactured items. After three months at sea and close to her destination, a navigational error caused the Falls of Halladale to be wrecked on a reef off the Peterborough headland on the 15th of November, 1908. The captain and 29 crew members survived, but her cargo was largely lost, despite two salvage attempts in 1908-09 and 1910. The Court of Marine Inquiry in Melbourne ruled that the foundering of the ship was entirely due to Captain David Wood Thomson's navigational error, not too technical failure of the Clyde-built ship. The Falls of Halladale was built in1886 by Russell & Co., at Greenock shipyards on the River Clyde, Scotland for Wright, Breakenridge & Co of Glasgow. She was one of several designs of Falls Line of ships named after waterfalls in Scotland. The company had been founded between 1870- 1873 as a partnership between Joseph Russell, Anderson Rodger, and William Todd Lithgow. During the period 1882-92 Russell & Co. standardised designs, which sped up their building process so much that they were able to build 271 ships during that time. The Falls of Halladale had a sturdy construction built to carry maximum cargo and was able to maintain full sail in heavy gales, one of the last of the 'windjammers' that sailed the Trade Route. She and her sister ship, the Falls of Garry, were the first ships in the world to include fore and aft lifting bridges. Previous to this, heavily loaded vessels could have heavy seas break along the full length of the deck, causing serious injury or even death to those on deck. The new raised catwalk-type decking allowed the crew to move above the deck in stormy conditions. The wheel spoke was part of the cargo on the ship, Falls of Halladale, along with buggy wheels. These are examples of parts of vehicles used at the beginning of the 20th century and could have been built components for buggies or wagons if delivered to their destinations of Melbourne or Sydney. The Falls of Halladale shipwreck is listed on the Victorian Heritage (No. S255). She was one of the last ships to sail the Trade Routes from Europe and the Americas. Also of significance is that the vessel was one of the first ships to have fore and aft lifting bridges as a significant safety feature still in use on modern vessels today. The subject model is an example of an International Cargo Ship used during the 19th and early 20th centuries to transport goods around the world and represents aspects of Victoria’s shipping industry. Wagon wheel spoke, light coloured wood, flat length, tongue shaped at the end. It was recovered from the wreck of the Falls of Halladale. flagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, russell & co., spoke, wagon wheel spoke, wreck artifact, falls of halladale, buggy wheel spoke, wheel spoke, cargo

Eulogy as Charter President of Inner Wheel Club of Bendigo South for Elsie Twitt. Also Eulogy & History as Charter President of Rotary Club Bendigo South. Mentioned is the origin of the Inner Wheel and the beginning of the Inner Wheel Club in Bendigo. Also mentioned is the lighted candle she always lit at the meetings of the Club. It became known as the Flame of Friendship. Mentioned is the aims and objectives of Inner Wheel. At the end is a prayer called The Collect.bendigo, clubs, inner wheel club south bendigo, inner wheel club south bendigo: elsie twitt eulogy, bendigo club, rotary club of bendigo south, flame of friendship, ron twitt

Miniature water turbine (pelton wheel, single jet) mounted on a wooden frame. Undershot wheel driving a pulley at one end of the shaft. Flywheel at the other end of the shaft. Small die-cast buckets, some broken and missing. Pelton wheel and flywheel painted red, wooden frame unpainted.Nonemachinery; water turbine; power

In 1932 Councilor H.J.Wheeler was elected as a member of Ballarat Shire Council and served until 1946. He served two terms as Shire President in 1937-38 and 1943-44.Original Historic Photo of Councilors for the year 1942-43.Rectangular with curved top,Sepia photo on brown mount, of Councilor H.J.Wheeler, top row ,left hand side of collection of photos of all councilors for the year 1942-43.Presented to the Ballarat Shire Council by Councilor R.T. White (J.P.) President 1942-43. wheeler, ballarat shire council, h j councilor, 1942 43

This item is in the gardens of the Bendigo District RSL Sub Branch Havilah Road.Hawkei protected Mobility vehicle, camouflage colours, 4 wheeled.“Hawkei”brsl, smirsl, bdrslinc, hawkeye

SEPIA PHOTOGRAPH OF CONSTRUCTION OF "WHEELERS" BRIDGE AT LAWRENCE MOUNTED ON CARDBORADTHE FIRST REINFORCED CONCRETE BRIDGE IN AUSTRALIA. ENGINEER - JOHN MONASH. LATER SIR JOHN MONASH.local history, photography, photographs, bridges

Traditional wooden Spinning Wheel---wooden with Bobbin, tripod legs Nonespinning wheel, wool

Belltower Pottery was established by Rudolf Dybka in Kyabram, Victoria, in around 1977 with the help of John Stroomer. Stroomer later took over the pottery, employing as many as 23 workers and apprentices. After a fire in 1988 destroyed the building, Stroomer moved the pottery to the old Kyabram butter factory, where it operated until the late 1990s. Works may be marked with an impressed 'Belltower Pottery' or, after the move to Kyabram, 'Belltower Pottery, Handmade, Kyabram, Vic.'Wheel thrown stoneware bowl with the word 'Nuts' on one side. Stamped "'Belltower Pottery, Handmade, Kyabram, Vic"pottery, belltower pottery, kyabram, australia studio pottery

Belltower Pottery was set up by Rudolf Dybka in Kyabram, Victoria, in around 1977 with the help of John Stroomer. Stroomer later took over the pottery, employing as many as 23 workers and apprentices. After a fire in 1988 destroyed the building, Stroomer moved the pottery to the old Kyabram butter factory, where it operated until the late 1990s. Works may be marked with an impressed 'Belltower Pottery' or, after the move to Kyabram, 'Belltower Pottery, Handmade, Kyabram, Vic.'Wheel thrown stoneware bowl with the word 'Nuts' on one side. pottery, belltower pottery, rudolf dybka, john stroomer

Black and white photograph of Miss Bertha Hansen at the wheel of the Canberragenealogy

Mining Relic found at Deep Lead Part of Trolley Wheelstawell

This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Wheel thrown stoneware lidded jar. Decorated with tenmoku glaze. art, artwork, ruth kealy, ceramics, tafe ceramics collection, available

This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Wheel thrown, stoneware vessel with lid decorated with tin glaze.art, artwork, ceramics, sam drew

This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Small wheel thrown bowl decorated with white crackle glaze.art, artwork, ceramics

This item is part of the Federation University Art Collection. The Art Collection features over 1000 works and was listed as a 'Ballarat Treasure' in 2007.Wheel thrown lidded vessel. Decorative glazed. Artist unknown. art, artwork

Colour photograph of a stone cairn with a metal cog wheel on top of it.In commemoration of the Turriff West Pioneer Settlers who built a bush church on this site 1914-1915 'To satisfy a need for god'cairn, memorial, turriff, turriff west, pioneer memorial, bush church, turriff west bush church

Black and White photo of Sister Rock's with people in horse and buggies in front of the rocks. One with two wheels and 3 people the other with 4 wheels and one person. There are 3 people sitting up on the rocks. Two Black & White photograph of Sister Rock's. The photos have in the foreground, a two wheel buggy with 3 people and a four wheel buggy with one person. There are also people up on the rocks.

Wooden pulley wheel section from the wreck “Newfield”. The Newfield was a three-masted iron and steel barque, built in Dundee, Scotland, in 1889 by Alexander Stephen and Sons. It was owned by the Newfield Ship Company in 1890 and later that year It was registered in Liverpool to owners Brownells and Co. The Newfield left Sharpness, Scotland, on 28th May 1892 with a crew of 25 under the command of Captain George Scott and on 1st June left Liverpool. She was bound for Brisbane, Australia, with a cargo of 1850 tons of fine rock salt, the main export product of Sharpness. At about 9pm on 28th August 1892, in heavy weather, Captain Scott sighted, between heavy squalls, the Cape Otway light on the mainland of Victoria but, due to a navigational error (the ship’s chronometers were wrong), he assumed it to be the Cape Wickham light on King Island, some 40 miles south. He altered his course to the north, expecting to enter Bass Strait. The ship was now heading straight for the south west Victorian coast and at about 1:30am ran aground on a reef about 100 yards from shore and one mile east of Curdie’s Inlet, Peterborough. The ship struck heavily three times before grounding on an inner shoal with 6 feet of water in the holds. Rough sea made the job of launching lifeboats very difficult. The first two lifeboats launched by the crew were smashed against the side of the ship and some men were crushed or swept away. The third lifeboat brought eight men to shore. It capsized when the crew tried to return it to the ship for further rescue The Port Campbell rocket crew arrived and fired four rocket lines, none of which connected with the ship. A local man, Peter Carmody, volunteered to swim one mile to the ship with a line to guide the fourth and final lifeboat safely to shore. Seventeen men survived the shipwreck but the captain and eight of his crew perished. The Newfield remained upright on the reef with sails set for a considerable time as the wind slowly ripped the canvas to shreds and the sea battered the hull to pieces. The Marine Board inquiry found the wreck was caused by a "one man style of navigation" and that the Captain had not heeded the advice of his crew. According to Jack Loney ‘… when the drama was over . . the Newfield was deserted except for the Captain’s dog and two pigs.’ Flagstaff Hill Maritime Museum has several artefacts that have been salvaged from the wreck. See also other items in the Flagstaff Hill Newfield Collection.The report from SHP documented the following in regards to the Newfield collection: Flagstaff Hill’s collection of artefacts from the Newfield is of historical and archaeological significance at a State level, because of its association with the shipwreck, which is on the Victorian Heritage Register. The collection is significant because of its relationship between the objects. The Newfield collection is archaeologically significant as it is the remains of an international cargo ship. The Newfield collection is historically significant for representing aspects of Victoria’s shipping history and its potential to interpret sub-theme 1.5 (Living with natural processes). The collection is also historically significant for its association with the shipwreck. The Newfield collection meets the following criteria for assessment: Criteria A: Importance to the course, or pattern, of Victoria’s cultural history Criteria B: Possession of uncommon, rare or endangered aspects of Victoria’s cultural history Criteria C: Potential to yield information that will contribute to an understanding of Victoria’s cultural history This item is an oval-shaped brown and orange wooden shell from a ship’s pulley. The original wooden material is now petrified but the lighter coloured concentric rings of the wood's grain are still visible. A metal sheave or drum is fitted into the centre hole and some of the edge of its sheave’s collar has corroded and broken away. The collar has three holes of equal size that are evenly spaced around it. The bearing ring is now detached but still connected to the pulley with a string on which a label is attached. Most of the six cylindrical metal roller bearings are sand encrusted but some are still visible. Recovered from the wreck of the ship NEWFIELD.The pulley has a string through it that attaches it to the bearing. The label on the string bears the handwritten words “PULLEY WHEEL / NEWFIELD / PETER ROLAND”.block, flagstaff hill, maritime museum, shipwreck coast, warrnambool, peter carmody, carmody, newfield, shipwreck, pulley, wheel, pulley block, sheave, drum, peterborough, south west victoria, rocket, rocket crew, shipwreck artefact, flagstaff hil maritime museum

Vintage opisometer used for measuring distances on maps. Part of the Kevin John Herdman, No. 397661, Collection. See Catalogue No. 5942P for details of his service record..1) Circular chromed metal instrument with handle. Calibrated dial with black markings and hand on a white background. Reverse face has unit conversion details in black text on white background. Each face is covered with a convex glass lens. On the opposite end to the handle is a small wheel with milled edge. As it turns, the hand on the front dial turns to measure distance. .2) Rigid plastic rectangular storage case in two parts. Base is yellow, top is clear..1) Printed on front dial: 'INCHES, MADE IN FRANCE'. Printed on back dial: 'Unit conversion details'. Stamped on metal near wheel: 'DEPOSE, H(logo)B'. .2) Stamped on clear cover: 'CURVIMETRE, MAP MEASURER, H(logo)B, MADE IN FRANCE'.map, map measure, equipment, opisometer, kevin john herdman

The early settlers of Orbost had to be self sufficient making their own clothes, tableware, bed coverings, furnishings and equipment. Many women were skilled dressmakers and craft workers. This item reflects that time.A small black hand-cranked lockstitch sewing machine. It has a backwards C-shaped body. The wheel and base are decorated with a gold pattern. On the end above the needle assembly is a brass plate The balance wheel has a handle. The pattern on the wheel is a gold border with two gold, red and green stars formed by interwoven triangles. On the cloth plate is stamped "Patent March 1867 Heron Gresham" with some indecipherable marks.sewing-machine needlework

This item was made by John Russell Senior, a blacksmith, wheelwright, farmer and later chairman of the Orbost Butter Factory, makers of Sunny South Butter (today part of Murray Goulburn Co Ltd). The buggy lifter was handed down to George Henry Russell (Doug), the second son between 1970 and 1973.Blacksmiths played an essential part in the regional parts of Victoria and were required to use their ingenuity and skills to design and make tools needed on local farms. This item is an example of a tool specifically designed for a horse-drawn wagon. Horse-drawn wagons are an important part of Australia’s agricultural history. Light buggies were popular with farmers for trips into town before the common use of motorised vehicles.A metal buggy wheel lifter. It has two hooks connected at the top by a bolt and a shackle. The hooks fit under the rim to enable the wheel to be lifted with a pulley / crane system operated by a man or a horse.tool buggy-lifter russell-john blacksmith wheelwright

The flywheel possibly belongs to a Walker's Cherub Mark III Ship-log taffrail, how the flywheel operates is a metal loop of the recording log would have been connected to the flywheel, so you could see if it was spinning properly. After the flywheel, is the rotor that was towed behind the ship and the revolutions of the rotor would register on the indicator, thus measuring the distance the vessel had travelled. Thomas Ferdinand Walker (1837–1921) first patented the Cherub log in 1878. It was one of the first logs in which the recorder was placed onboard a ship rather than being incorporated as part of the rotor. The Cherub Mark III series was produced from 1930 it came in two versions a thousand-mile which is quite rare and a five hundred-mile version.This ship log flywheel was invented and made by a significant marine instrument maker and innovator of machinery Thomas Walker. It demonstrates the huge leap taken to improve navigational accuracy at sea with an instrument that was in use for decades to measure the distance travelled at sea updated versions are in use today by mariners.Log Governor (or Fly-wheel) from a Ships Taffrail Log, metal wheel with 6 spokes, hub has rope attached for connecting to ships log. Boss the other side for attachment to the spinner.Noneflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, log governor

Log Governor (or Fly-wheel) from a Ship Log; metal wheel shape with 6 spokes, hub has rope attached for connecting to ships log. Metal hook detached from rope.flagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, log governor (or fly-wheel), log governor, fly-wheel

Textiles. Calico flour bag printed on one side in blue, ''WATER WHEEL FLOUR, BRIDGEWATER, VICTORIA, AUSTRALIA.25 lbs gross weight when packed. In the centre is a picture of a water wheel.textiles, domestic, water wheel, bridgewater flour bag

Wheel metal part of pulley has 6 spokes & hole in centreflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

This hand drill was colloquially called an ‘egg beater drill’ due to its method of operation, and was aesthetically similar in appearance to the ‘breast drill’, with the former having a rounded handle instead of a concave bracing surface. Originally designed for drilling into metal, its gears allowed for higher rotation speeds and finer accuracy. This drill was probably manufactured in the 1960s by German company BECON. Distributed in Australia by Beck & Coram, it was widely used and easily accessible.Hand drill with red wheel, dark red paint remnants on handleBECON D129hand drill, hand tools, wood working tools, churchill island

Handled Cork lid No label Trade mark symbol is a wagon wheelMarchant & Co Registered Australia Trade Mark

A sepia photograph (postcard) of a 5? storey stone mill with water wheel.Printed on front: THE OLD MILL SUNBURY Printed on back: POST CARD / CARRESPONDENCE / ADDRESS ONLY / TOold mill, mills, sunbury, postcards, water wheels, george evans collection