Single page A4 photocopy of a Interoffice Memo dated 8/2/1984, from the Running Sheds Engineer to Depot staff titled "Failure of Motor Armature Bearings", sign Alan Nolan. Describes the problem with the failure of bearings, inspection requirements, and looking for burnt wool or burnt wool smells. trams, tramways, w class trams, bogies, overhauls, maintenance, bearings

Produced by the SECV to document the Motor Armature Bearings.Yields information regarding the dimensions of the Armature Bearings Westinghouse 225N Motor.SEC drawing number GE-T8-8114, Geelong Branch, "Switch Tongues Tramway Permanent Way.". Drawn 24/04/1945. Blueprint drawing. electricity supply department, secv, works division, provincial tramways, tramways, armatures, bearings, westinghouse 225

Sixty page book - gloss paper, plus end papers and heavy card covers, titled "SKF Bearings in Tramway Service". Published by the "The SKF Ball Bearing Company Ltd" in August 1939, gives details of the type of ball bearings available for tramcars - axle boxes, tramway motors, current collection - trolley poles and pantographs. Has drawings, illustrations, photographs etc. Photographs include Hobart 8 and a Wellington Fiduca tram. Address of Melbourne office given as 539 Bourke St, also addresses for Sydney and Brisbane. Printed in Sweden.$20 inside front cover.trams, tramways, tramcars, bearings, skf ball bearings, hobart

Memorandum - A4 sheet, dated 8/2/1984 from Runningsheds Engineer A. Nolan to depots titled "Failure of Motor Armature Bearings". Notes that there have been an increase in bearing failures and the problems resulting. Printed on Metroplan Transit Authority letterhead.trams, tramways, mta, depots, bearings, armatures, tramcars, maintenance

Instruction - printed on two A3 sheets, titled "The Care of Railway Motor Bearings" issued by General Electric July 1925. Details bearing lining materials for brass and Babbitt, armature, axle, iron, packing, oil levels and inspection. Original from a wall poster.trams, tramways, electrical engineering, electrical equipment, motors, electric traction, general electric, bearings, maintenance

Produced by the SECV to document the General Electric motor, GE201.Yields information regarding the GE201 Armature Bearings Comm. & Pinion End.SEC drawing number VW4/22, "Tramways GE201 Armature Bearings Comm. & Pinion End". Drawn 15/01/1962. Beige paper copy of original dyeline print. Copy of original.electricity supply department, secv, works division, ge201, general electric

Hand written record of the type of armature lining (All duty or Graphine 2) metal used to line the bearing. Gives armature number, type of metal, date and type of motor. Sheet dated 31/5/1940. Has notes in the bottom right-hand corner about the bearing metal used and whether new or reconditioned.Yields information about the type of metal used to white metal armature bearings in Ballarat.Foolscap sheet, unruled, with details in pencil and folded 12 times.tramcars, equipment, rolling stock, armatures, bearings, motors

This mangle, sometimes referred to as a wringer, was donated to Flagstaff Hill Maritime Village by the family of Doctor William Roy Angus, Surgeon and Oculist. It is part of the “W.R. Angus Collection” includes historical medical equipment, surgical instruments and material once belonging to Dr Edward Ryan and Dr Thomas Francis Ryan, (both of Nhill, Victoria) as well as Dr Angus’ own belongings. The Collection’s history spans the medical practices of the two Doctors Ryan, from 1885-1926 plus that of Dr Angus, up until 1969. The mangle was used in laundries to squeeze water from washed items and hasten the drying process. This particular wringer is larger that the usual household design and was possibly amongst the original furnishings of "Birchwood", the 1852 home of Dr Henderson when Dr. Angus purchased his home and medical practice in Koroit St, Warrnambool. The wooden rollers date the mangle to one of the earlier models manufactured. ABOUT THE “W.R.ANGUS COLLECTION” Doctor William Roy Angus M.B., B.S., Adel., 1923, F.R.C.S. Edin.,1928 (also known as Dr Roy Angus) was born in Murrumbeena, Victoria in 1901 and lived until 1970. He qualified as a doctor in 1923 at University of Adelaide, was Resident Medical Officer at the Royal Adelaide Hospital in 1924 and for a period was house surgeon to Sir (then Mr.) Henry Simpson Newland. Dr Angus was briefly an Assistant to Dr Riddell of Kapunda, then commenced private practice at Curramulka, Yorke Peninsula, SA, where he was physician, surgeon and chemist. In 1926, he was appointed as new Medical Assistant to Dr Thomas Francis Ryan (T.F. Ryan, or Tom), in Nhill, Victoria, where his experiences included radiology and pharmacy. In 1927 he was Acting House Surgeon in Dr Tom Ryan’s absence. Dr Angus had become engaged to Gladys Forsyth and they decided he further his studies overseas in the UK in 1927. He studied at London University College Hospital and at Edinburgh Royal Infirmary and in 1928, was awarded FRCS (Fellow from the Royal College of Surgeons), Edinburgh. He worked his passage back to Australia as a Ship’s Surgeon on the on the Australian Commonwealth Line’s T.S.S. Largs Bay. Dr Angus married Gladys in 1929, in Ballarat. (They went on to have one son (Graham 1932, born in SA) and two daughters (Helen (died 12/07/1996) and Berenice (Berry), both born at Mira, Nhill ) According to Berry, her mother Gladys made a lot of their clothes. She was very talented and did some lovely embroidery including lingerie for her trousseau and beautifully handmade baby clothes. Dr Angus was a ‘flying doctor’ for the A.I.M. (Australian Inland Ministry) Aerial Medical Service in 1928 . Its first station was in the remote town of Oodnadatta, where Dr Angus was stationed. He was locum tenens there on North-South Railway at 21 Mile Camp. He took up this ‘flying doctor’ position in response to a call from Dr John Flynn; the organisation was later known as the Flying Doctor Service, then the Royal Flying Doctor Service. A lot of his work during this time involved dental surgery also. Between 1928-1932 he was surgeon at the Curramulka Hospital, Yorke Peninsula, South Australia. In 1933 Dr Angus returned to Nhill and purchased a share of the Nelson Street practice and Mira hospital (a 2 bed ward at the Nelson Street Practice) from Dr Les Middleton one of the Middleton Brothers, the current owners of what previously once Dr Tom Ryan’s practice. Dr Tom and his brother had worked as surgeons included eye surgery. Dr Tom Ryan performed many of his operations in the Mira private hospital on his premises. He had been House Surgeon at the Nhill Hospital 1902-1926. Dr Tom Ryan had one of the only two pieces of radiology equipment in Victoria during his practicing years – The Royal Melbourne Hospital had the other one. Over the years Dr Tom Ryan had gradually set up what was effectively a training school for country general-practitioner-surgeons. Each patient was carefully examined, including using the X-ray machine, and any surgery was discussed and planned with Dr Ryan’s assistants several days in advance. Dr Angus gained experience in using the X-ray machine there during his time as assistant to Dr Ryan. When Dr Angus bought into the Nelson Street premises in Nhill he was also appointed as the Nhill Hospital’s Honorary House Surgeon 1933-1938. His practitioner’s plate from his Nhill surgery is now mounted on the doorway to the Port Medical Office at Flagstaff Hill Maritime Village, Warrnambool. When Dr Angus took up practice in the Dr Edward and Dr Tom Ryan’s old premises he obtained their extensive collection of historical medical equipment and materials spanning 1884-1926. A large part of this collection is now on display at the Port Medical Office at Flagstaff Hill Maritime Village in Warrnambool. In 1939 Dr Angus and his family moved to Warrnambool where he purchased “Birchwood,” the 1852 home and medical practice of Dr John Hunter Henderson, at 214 Koroit Street. (This property was sold in1965 to the State Government and is now the site of the Warrnambool Police Station. and an ALDI sore is on the land that was once their tennis court). The Angus family was able to afford gardeners, cooks and maids; their home was a popular place for visiting dignitaries to stay whilst visiting Warrnambool. Dr Angus had his own silk worm farm at home in a Mulberry tree. His young daughter used his centrifuge for spinning the silk. Dr Angus was appointed on a part-time basis as Port Medical Officer (Health Officer) in Warrnambool and held this position until the 1940’s when the government no longer required the service of a Port Medical Officer in Warrnambool; he was thus Warrnambool’s last serving Port Medical Officer. (Masters of immigrant ships arriving in port reported incidents of diseases, illness and death and the Port Medical Officer made a decision on whether the ship required Quarantine and for how long, in this way preventing contagious illness from spreading from new immigrants to the residents already in the colony.) Dr Angus was a member of the Australian Medical Association, for 35 years and surgeon at the Warrnambool Base Hospital 1939-1942, He served as a Surgeon Captain during WWII1942-45, in Ballarat, Victoria, and in Bonegilla, N.S.W., completing his service just before the end of the war due to suffering from a heart attack. During his convalescence he carved an intricate and ‘most artistic’ chess set from the material that dentures were made from. He then studied ophthalmology at the Royal Melbourne Eye and Ear Hospital and created cosmetically superior artificial eyes by pioneering using the intrascleral cartilage. Angus received accolades from the Ophthalmological Society of Australasia for this work. He returned to Warrnambool to commence practice as an ophthalmologist, pioneering in artificial eye improvements. He was Honorary Consultant Ophthalmologist to Warrnambool Base Hospital for 31 years. He made monthly visits to Portland as a visiting surgeon, to perform eye surgery. He represented the Victorian South-West subdivision of the Australian Medical Association as its secretary between 1949 and 1956 and as chairman from 1956 to 1958. In 1968 Dr Angus was elected member of Spain’s Barraquer Institute of Barcelona after his research work in Intrasclearal cartilage grafting, becoming one of the few Australian ophthalmologists to receive this honour, and in the following year presented his final paper on Living Intrasclearal Cartilage Implants at the Inaugural Meeting of the Australian College of Ophthalmologists in Melbourne In his personal life Dr Angus was a Presbyterian and treated Sunday as a Sabbath, a day of rest. He would visit 3 or 4 country patients on a Sunday, taking his children along ‘for the ride’ and to visit with him. Sunday evenings he would play the pianola and sing Scottish songs to his family. One of Dr Angus’ patients was Margaret MacKenzie, author of a book on local shipwrecks that she’d seen as an eye witness from the late 1880’s in Peterborough, Victoria. In the early 1950’s Dr Angus, painted a picture of a shipwreck for the cover jacket of Margaret’s book, Shipwrecks and More Shipwrecks. She was blind in later life and her daughter wrote the actual book for her. Dr Angus and his wife Gladys were very involved in Warrnambool’s society with a strong interest in civic affairs. He had an interest in people and the community They were both involved in the creation of Flagstaff Hill, including the layout of the gardens. After his death (28th March 1970) his family requested his practitioner’s plate, medical instruments and some personal belongings be displayed in the Port Medical Office surgery at Flagstaff Hill Maritime Village, and be called the “W. R. Angus Collection”. The W.R. Angus Collection is significant for still being located at the site it is connected with, Doctor Angus being the last Port Medical Officer in Warrnambool. The collection of medical instruments and other equipment is culturally significant, being an historical example of medicine from late 19th to mid-20th century. Dr Angus assisted Dr Tom Ryan, a pioneer in the use of X-rays and in ocular surgery. Large mangle (or wringer) with wooden handle, hardwood wooden rollers and metal stand, part of the W.R. Angus Collection. Household clothes mangle with steel ball bearings, made by the American Wringer Co. New York, U.S.A. Brand and details are printed on side. Printed on side; "HOUSEHOLD / CLOTHES MANGLE / STEEL BALL BEARINGS / THE AMERICAN WRINGER Co, NEW YORK, USA” and on top "NO. HARDWOOD ROLLERS 124"flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, dr w r angus, dr ryan, surgical instrument, t.s.s. largs bay, warrnambool base hospital, nhill base hospital, mira hospital, flying doctor, clothes mangle, clothes wringer, laundry equipment, the american wringer company, mangle with wooden rollers, mangle with settl bearings

The Claymore mine is a directional mine with 700 small ball bearings. This small section was brought home from Vietnam by George Cameron Wood No 3798253. Refer Cat no 1872 for his service history.Corner section fragment from an M18A1 Claymore anti-personnel mine. Hard green plastic front, rear has a large number of approx. 3mm diameter ball bearings set in black epoxy resin.arms-ammunition, claymore

Five letters referring nylon bearings for use with Scalebuoys.Two dated 20/9/1957 and 30/9/1957 are from McPherson's Limited with information on the bearings. Three dated 16/9/57, 2/11/57 and 28/9/57 are enquiring about the suitability of the nylon bearings.sciences, bill ashman collection - correspondence, mcpherson's limited, bendigo electronic company of aust ltd, h g england, nylon bushing

Delivery docket number 96686. Form 1/118 - Jan 1959. Delivery details handwritten in blue ink. To "Mr R Prentice T M S" (TMSV) From "Preston" (?) "4. whitemettaled Saddle brasses" - (for use as Axle bearings) "Sundry Debtor. H.O."trams, tramways, preston, forms, equipment, axles, tramcar equipment, tmsv, bearings

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples such as the subject item have no makers names.A vintage drilling tool that gives a snapshot into how holes were drilled by hand into small or delicate objects during the Victorian era. Tools from this time are today regarded as collectable items eagerly sought by collectors of antique tools. Archimedean drill with Rosewood hand, brass bearings, steel twist and wooden grip. Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill, archimedean drill with wooden hand, drilling tool

A large device for drying laundry consisting of two rollers between which the wet laundry is squeezed (or wrung); a mangle. American English uses the term 'Wringer' whereas UK English uses the term 'mangle'. Later devices were typically electrified.Large mechanical hand cranked household laundry mangle with hardwood rolls and metal fittings. Information about the equipment is stamped/incised on both the metal and wooden frame.Household Clothes Mangle /American Wringer No 120 / Inc Metal Bearings / / Hardwood Rollslaundry equipment, household mangle, wringer

The M18A1 'Claymore' Directional Fragmentation Mine which is used as part of the perimeter defences at, for example Fire Support Base or for use in ambush situations. The convex side is faced toward the enemy and the mine is configured to be electrically detonated from a remote location, (these mines can be connected by white "det cord" & detonators from the detonator wells show to link a series of mines)). It is raised off the ground by a small stand to maximise the blast radius. Claymore mines contain 700 steel ball bearings impressed into 650 grams of plastic explosive. The M18A1 has a lethal range of up to 100 metresA replica of the M18A1 'Claymore' Directional Fragmentation Mine. The convex side is faced toward the enemy and the mine is configured to be electrically detonated from a remote location. In practice this mine type is raised above the ground slightly by a small legs designed to maximise the blast radius. These mines contain approximately 700 small steel ball bearings impressed into 650 grams of plastic explosive. The M18A1 has a lethal range of up to 100 metresOn the front"Front Toward Enemy" on the reverse "Back M18A1 Apers Mine"

Clothes mangle [wringer] Wooden metal Turning Handle & rachet 2 tap screws for pressure B/N RollerHardwood rolls No 124 Household clothes Steel Ball Bearings The American Wringer Co New York USA

Memorandum, typed foolscap, 4 sheets, titled "Notes on Rolling Stock Maintenance Practice", undated, late 1930's? looking at MMTB Workshop and depot maintenance practices, for tramcars. Gives details of the shifts, cleaning, motor inspections, grinding, the use of a single truck breakdown tram, grinding of wheels at depots, annual mileages, defect rate, use of roller bearings on armatures, painting of trams, gear shield grease and varnishing or lacquering of seats and interiors,trams, tramways, tramcar components, brakes, depots, workshops, maintenance, motors, rolling stock, bearings, paint