Letter typed on MMTB Letterhead quarto paper with the name of the Secretary, Telegraphic address and contact details - to J. Bounds of East St Kilda regarding this letter requesting advice on the Brill 21E truck at the Hawthorn Driving School. Advised that it had agreed to dispose it to the TMSV. Dated 6/11/1972. Signed R. M Brown (?) Assistant Secretarytrams, tramways, mmtb, brill trucks, hawthorn, tmsv

Contains an article that looks at the development of the four wheel Brill 21E in regard to the engineering aspects. Written by N. F Henley with drawings of the various concepts and history of the Brill truck. See item 7384 for s similar article on the Brill 22E truck.Yields information about the development of the Brill 21E truck which is used on some of the BTM trams.Magazine 40 pages, centre stapled, Tramway Review published by the Light Railway Transit Association, Autumn 1990.trams, tramways, bogies, trucks, brill trucks, brill 21e

Black and White photograph of a Brill 21E type, used on four wheel trams. Note the motor suspension spring is not located in the original position provided for on the truck. One of a series of photographs done by the MMTB to illustrate the various types of bogies used by the MMTB. Possibly during the 1960's.trams, tramways, mmtb, brill trucks, brill 21e, bogies, trucks, preston workshops

The drawing provides details of the two sets of springs that fit on either side of the axle box of a Brill 21E four-wheel truck. Gives load, sizes, and material dimensions. Revision E dated 7-11-1958. Prepared by the MTTB for use on four-wheel trams. Original drawing dated 30/9/1927Yields information about Brill 21E truck axle box springs.Drawing Foolscap size with two punched holes on the left hand side.tramcars, 21e trucks, brill 21e, springs, mmtb

Black and White photograph of a MMTB workshop dolly made from a former Brill 21E truck cut down and fitted with centre pin and bolsters. One of a series of photographs done by the MMTB to illustrate the various types of bogies / trucks used by the MMTB. Possibly during the 1960's. Two copies held.trams, tramways, mmtb, bogies, trucks, preston workshops, brill 21e

Black and White photograph of a Brill 21E type, used on four wheel trams. Note the motor suspension spring is not located in the original position provided for on the truck. One of a series of photographs done by the MMTB to illustrate the various types of bogies used by the MMTB. Possibly during the 1960's. Two copies held.trams, tramways, mmtb, brill trucks, brill 21e, bogies, trucks, preston workshops

Black and white negative, by Wal Jack, of Freight car No. 17 at Brunswick Depot. Photo dated, 23/5/1941 in the Wal Jack album. See also Reg item 5238 for another photo of this car at Brunswick.trams, tramways, freight tram, brunswick, brill 21e, tram 17

Black and white negative, by Wal Jack, of Freight car No. 17 in Cameron St, Brunswick. Has the Coburg rail line in the background. Shows the 21E truck. Dated 8/1940. May not be a Wal Jack photograph as odd negative size. See also Reg item 5333 for another photo of this car at Brunswick.trams, tramways, freight tram, brunswick, cameron st, brill 21e, tram 17

Article looks at the development of the maximum traction bogie, the Brill 22E in regard to the engineering aspects. Written by N. F Henley with drawings of the various concepts and history of the Brill truck. See item 9663 for s similar article on the Brill 21E truck.Yields information about the development of the Brill 22E truck which is used on some of the BTM trams.Seven A4 sheets, photocopy of an article titled "The development of the Manchester bogie" from the UK magazine Tramway Review published by the Light Railway Transit Association, Winter 1988.trams, tramways, maximum traction, bogies, trucks, brill trucks

Set of two black and white photographs which have been coloured to show possible arrangements for covers to the side frames of a Brill 21E and Brill 22E (single truck or four wheel truck or bogie tram). 1793.1 - Showing possible arrangement for a cover for a maximum traction tram truck - cover has been outlined in red and then coloured to match the tram colour. The body has been coloured as well with green and yellow colours. 1793.2 - ditto for single truck tram No. 20. Background for the preparation of these photographs is unknown. Date unknown.trams, tramways, trucks, covers, brill trucks, tram 20

Series of four Black and white photographs of tram 26 on No. 2 road at the BTPS Depot, undergoing replacement of the broken frame on the Brill 21E truck. The tramcar record sheets note that the car was lifted 15-3-1975 and lower 27-7-1975 and tested on the same day. Seems to have re-entered service on 28/9/1975. .1 - on the front of the road, with a "Defective Not for Service" sign. .2 - car on jacks being either lifted or lowered. .3 - tramcar body lifted showing the word to replace the side frame underway, has the good and broken side frame in the view. .4 - tram being either lifted or lowered - with Rolf Jinks in the view. trams, tramways, btps, depot, brill trucks, maintenance, tram 26

Green folder gold block printed cover for "The J.G. Brill Company" and associated companies containing the following bulletins. All four pages, unless noted otherwise, printed on art paper, with the company name associated companies and agencies - e.g. Noyes Bros in Australasia. Contain a photo of the truck, a photo of a vehicle using the truck or bogie, line diagram, dimensions and parts diagram and listing. Bulletins 229, 246, 247 and 249 are for window (sash) components seats. Give diagrams and photos of this equipment. 1. No. 220 - The Brill 21E truck 2. No. 221 - Brill No. 50E truck 3. No. 224 - The Brill 27MCB truck 4. No. 225 - The Brill 76E truck 5. No. 227 - The Brill 39E truck 6. No. 228 - The Brill 77E truck 7. No. 229 - The Brill Renitent Post 8. No. 234 - The Brill 78M truck for light weight cars 9. No. 236 - Parts of Brill Short Base Pivotal Truck No. 27G 10. No. 237 - Parts of Brill Short Base Pivotal Truck No. 27F 11. No. 238 - Parts of Brill High Speed Truck No. 27E 12. No. 240 - Two Important Brill full elliptic Spring Trucks - 51E and 68E types. 13. No. 242 - The Brill 79E truck for Birney Safety Cars 14. No. 246 - Brill Reversible seats - Winner and Waylo types - 8 pages 15. No. 247 - Brill Non-reversible seats. 16. No. 249 - The Motorman's seats for Birney Safety cars. (different style of layout). All contained with a 'Shipman's "Common-Sense" Binder', comprising a green cloth covered cardboard, continuous cover, printed end papers, binder clips for inserting documents. Style No. 62848. Gold block front with name of company and Brill logo and on spine of document "Brill Publications" in gold. Has a ESCo date stamp of 3 May 1921 on front page of Bulletin No. 220.On front cover of first Bulletin, date stamp of ESCo, Ballarat "3 May 1921" in purple ink.trams, tramways, 21e trucks, j c brill co, bogies, interurban, birney, brill trucks

Yields information about the drawings that were used by the depot or workshop staff as reference drawings. Has a strong association with the depot workshop staff. Yields information about equipment on Ballarat tramcars and Signalling.Folder containing 46 blueprints or Dyeline prints of SEC tram equipment drawings. Front of folder made from a cloth back sheet of paper extended to secure to a thick cardboard runner. Rear of folder made from an old tram advertising panel or cardboard sheet, cut to size and secured to a thick cardboard runner with a cloth backing on both sides. Sheets secured with three brass screwed clips. Front cover damaged in bottom right hand corner. Rear cover breaking apart on outside around cloth binding. Heavy dirt marks from “grease” on bottom half of rear cover. Contains 46 drawings which have been individually catalogued and numbered on the rear of each drawing within the folder. Some of the drawings have been folded. Reg Item Micro Film No. Old BTPS No. SEC Drawing No Title 4807 42/4 1 VB4/8103C Westinghouse T1F Controller Main Cylinder Segments. 4867 47/2 2 BA-T8-8128 Westinghouse 225N Motor Case Bolt 4830 22/3 B 3 BA-T7-7666 Half Ball Brake Hanger Link, Driving Wheel, Brill Maximum Traction Truck 22E 4868 44/3A 4 BA-T8-8113 Split Suspension Bearing for Type W225 Motor (Westinghouse) 4869 52/2 5 BA-T8-8158 Contact Tips for G.E. Compressor Controller 4818 52/3 6 BA-T8-8159 GE B-23 Contact Finger Tips for G.E. Type ‘B’ Main Cylinder 4870 6/1 7A BA-T3-6734 Brass Nut for Switch Mechanism 4829 6/2 7B BA-T3-6735 Tongue Clip Link for Switch Mechanism 4871 6/3 7C BA-T3-6736 Fulcrum for Switch Mechanism 4872 6/4 7D BA-T3-6737 Plunger for Switch Mechanism 4832 7/6 8 BA-T3-6754 Pivot for Switch Mechanism No numbers 9 or 10 4873 17/5 11 BA-T7-7639 Detail of Motor Pinion for Brill Cars 4831.2 21/4 B 12 BA-T7-7661A Half Ball Hanger Links – single bogie trucks 4874 21/6 13A BA-T7-7663 Axle Box Inner Spring Driving Wheels Maximum Traction Truck 22E 4875 22/1 13B BA-T7-7664 Axle Box Outer Spring Driving Wheels Maximum Traction Truck 22E 4876 22/2 14 BA-T7-7665 Body Spring Brill Maximum Traction Truck 22E 4830.2 22/3B 15 BA-T7-7666A Half Ball Brake Hanger Link Driving Wheel Brill Maximum Traction Truck 22E 4877 22/4 16 BA-T7-7667 Body Spring, Brush Maximum Traction Truck 22E 4820.2 22/6 A 17 BA-T7-7669 Wear cups for Half Ball Brake Hanger Links, Single & Double Bogie Trucks 4878 50/5 18 BA-T8-8149 Connections of Line Breaker and Ratchet Switch for use with Drum Controller 4879 74/6 19 BA-T13-8757/9 Signal boxes, Back of Panel Wiring and External Connections 4880 45/1 20 BA-T8-8116 Trolley Harp 4806 15/3 21 BA-T7-7625 Equalizing Lever, Fulcrum, Brill 21 E truck 4881 15/5 22 BA-T7-7626A Brake Beam Fulcrum Brill 21E truck 4808 16/1 23 BA-T7-7628 Pinion Remover, GE 201G and GE 202 motors 4882 16/3 24 BA-T7-7630 Spring Posts, Brill 21E Truck 4883 21/3 25 BA-T7-7660 Brake Shoe Holder, Driving Wheel, Maximum Traction Truck Brill 22E 4884 21/5 26 BA-T7-7662 Brake Rod Guide, Single Bogie Trucks 4885 22/5 27 BA-T7-7668 Brake Shoe Holder, Pony Wheel, Maximum Traction Truck Brill 22E 4809 42/2 B 28 BA-T8-8101 Trolley Wheel and Axle 4815 42/1 B 29 BA-T8-8102A Motor Suspension Bearing, GE 202 Motor 4796.2 42/5 30 BA-T8-8104 Connection Diagram WH 225N Motor 4886 42/6 B 31 BA-T8-8105B Motor Suspension Bearing, GE 201 Motor 4797.2 48/6 32 BA-T8-8137 WH T1F Controllers 4816 49/2 33 BA-T8-8138 Connection Diagram GE 202 Motor 4887 49/3 34 BA-T8-8139 Connection Diagram K-36-J Controller 4888 50/3 35 BA-T8-8146 GE K-36-JR Controllers, with line breaker (Connection diagram) 4889 50/6 36 BA-T8-8150 Commutator for Westinghouse 225N Motor 4846 51/1 37 BA-T8-8151A Armature Bearing Lining, Commutator End, Type GE 201G Motor 4813 51/2 38 BA-T8-8152 Armature Winding Diagram Westinghouse 225 Motor 4840.2 51/40 39 BA-T8-8154A Armature Bearing Lining, Pinion End, Type GE201G Motor 4890 51/6 40 BA-T8-8156 Armature Bearing Lining, Pinion End, Type GE202A Motor 4891 52/1 41 BA-T8-8157A Armature Bearing Lining, Commutator End, Type GE202A Motor 4892 64/5 42A BA-T9-8392A Step Hangers, Single and Double Bogie Trucks, Hinged Type 4785.2 64/6B 42B BA-T9-8392/1A Step Hangers, Single and Maximum Traction Trucks, Fixed Type 4812.2 43/1 43 BA-T8-8106B GE K36J Controller, Main Cylinder Segments 4893 50/2 44 BA-T8-8145A GE B23E Controller, Main Cylinder Segments 4816 65/2 45 BA-T9-8394B Door Lock for Motorman’ Cabin Maximum Traction Trucks. 4810 73/3 46 BA-T13-8757 Ballarat Electric Tramways Signalling System, Arrangements & Details of Box.On front cover of folder, "1 - 46"trams, tramways, drawings, ballarat, sec, depot, workshops

Catalogue No. 206 of the J. G. Brill Co. of Philadelphia PA, titled "Brill Trucks" on front cover and "City and Interurban Trucks" on page 1. Comprises: Card cover very light grey on outside, grey inside which is a larger size than that of the rest of the book. Has the names of the J. G. Brill associated companies (American Car Company of St. Louis, G. C. Kuhlman Car Co. of Cleveland Ohio, Wason Manufacturing Company of Springfield, Massachusetts and Compagnie J. G. Brill, Paris France) as well. On the inside of the front cover and on the inside back cover are patterns involving the Brill logo. To the printed catalogue is a matching out 4pp again with the same Brill logos. This sheet is the same size as the text pages. Forty page printed text on a heavy gloss manila colour art paper. Front cover gives details of Brill's office addresses, and agents, including the Australasian agent - Noyes Brothers. Page 3 gives an introduction to the quality of Brill trucks and page 39 gives an index to the various trucks and components. Each truck type has a photograph, parts list and dimension details. Trucks covered are: Radiax, 21E, 22, 22E, 27E, 27F, 27G, 27MCB, 39E, 50E. Equipment detailed are the Half-Ball brake hanger, oil retaining center bearing, standard journal (axle) box, solid forged side frames and axle data. Page 38 details the information to be provided when ordering trucks. Image of each sheet added 25/3/2015.On front cover, date stamp of ESCo, Ballarat "1 Apr 1914". The printers signature is shown on page 40.trams, tramways, 21e trucks, 22e trucks, j. c. brill co., bogies, interurban

Demonstrates aspects of the two types of trucks or bogies used on Ballarat trams and their design basis. Photocopied from a catalogue.Five pages, each page trimmed to a slightly different width, photocopy of an article titled "Brill's 21-E traction truck", reproduced from the 1905 Brill catalogue. Gives details of the truck, its capability, basis, use in New York for example, how it functions, load and speed capacity, motor size, basic dimensions, limitations and drawings. 2nd copy held as well - on toner based copy rather than heat sensitive paper. Scanned copies of all sheets added 25/3/15.trams, tramways, trucks, 21e trucks, brill trucks

Set of drawings and photocopies of sanding equipment on Ballarat Tramcars, provided to the Launceston tramway Museum for information.Copy of Correspondence with the Launceston Tramway Museum 31/12/2006 concerning sand ejector equipment fitted to Ballarat tramcars. Comprises: Covering letter dated 31/12/2009 Photographs of the Ejector unit with fittings - two views Photograph of the inlet pipe Sketch of the air inlet pipe - prepared by Warren Doubleday Prints of drawings - BA - T7 - 7654 - Ejector for Sand Box, Fabricated type - 21E truck, SEC 1938 - made from scans ex Microfilm BA - T7 - 7647 - Ejector for Sand Box, Brill 21 E Truck - SEC 1938 - cast type.tram, trams, tramcar equipment, sanding equipment, sand ejectors, letters