The 1982 Ford V6 engine, built at the Ford Essex Engine Plant at Windsor in Ontario Canada, was released by Ford for installation in a number of car and light truck models manufactured in Canada, United States, Mexico and Venezula. Production probably exceeded 7 million items. The Australian Gliding Museum’s exhibit was an engine converted for aircraft use that was bought for the Gliding Federation of Australia “Auto-Tug” program from Javelin Aircraft Company in Wichita in USA. “Auto-Tug” was an experimental program sponsored by the Gliding Federation of Australia to equip a glider – sailplane Piper Pawnee PA-25-150 tug with a water-cooled engine to alleviate the costs of running and maintaining the Lycoming engines fitted to Pawnee tugs in Australia. The program began in 1988 and was aimed at obtaining limited certification for converting dedicated glider – sailplane tow planes. The engine equipped with modified intake manifolds produced 198 hp for flight with the same propeller RPM for take-off as the original Lycoming 0-540 engine. However, fuel consumption was halved as the water cooling of the Ford engine enabled quicker descents with throttle closed following the release of the sailplane. Based on the results of GFA’s program, CASA concluded that engine was quite suitable for an aircraft installation and rated it more reliable than the equivalent Lycoming and Continental aircraft engine. The use of the 1982 Ford V6 engine type for Pawnee tug conversions was discontinued when the General Motors LS1 5.7 litre V8 became available. It is understood that a small number of conversions have been done using the LS1 engine. This brief history is based on information obtained from Mike Burns and David Sharples who were involved in the Auto-Tug program from 1988 to 1992. Technical information relating to the 1982 Ford V6 automotive engine is contained in a paper by D.L. Armstrong and G.F. Stirrat of the Engine Engineering Office at Ford. Indicative of technological experimentation in the sport of glidingFord auto engine mounted on mobile standaustralian gliding, glider, sailplane, auto-tug, pawnee, tug, auto, engine, motor, ford, gliding federation of australia, burns, sharples.

This Ford Handbook is in good condition. This book covers at least 97% of the instructions necessary for servicing the 1950 and 1951 models.Repair and Maintenance book covering all models of ford including V8, "60" and FORD SIXOn page 106 of the handbook there is, in handwriting, CABLE OPERATED BRAKES, Spring, Colour & Position Guide. Hand drawn picture with details marking the layout and details of the spring, colour & position.electrical, steering, ford, engine, transmission, accessory, ford owners, car repair, v8, 60, ford six, repair and maintenance, ford engine, clutch, body, chassis, shockers, cooling system, fuel system, suspension, rear, axle, brakes, shock absorbers, rear axle

3. 2 trucks have the 3rd MD TAC Sign, 1 truck has the TAC sign with 7 on it. Passchendaele Barracks was the name of the Army Drill Hall, Mollison Street, Bendigo. The drill hall was in use 1916 - abt 2004.1. Side view of international MK3 Army Truck 4 x 4 set up for troop or general service work. Canvas cover is on. Coloured photo taken in the Mollison Street Depot yard. Photo is mounted on stiff cardboard. 2. Side View of Army Commercial Ford Truck. Cabin tilted forward to enable access to engine (Ford CL 400). 3. Group photo in colour, of 5 MN3 trucks lined up on the road beside the Mollison Street Drill Hall,. 1. On the rear is a 'stuck on' label "International 2 1/2 tons GS MN3 Bendigo Deport Yard". 3. On the rear is written "Convoy Inter MK3's in Mollison Street Bendigo. trucks, cmf, passchendaele barracks trust

Auction catalogue for a sale on 13th March, 1946 under instructions from the Commonwealth Disposals Commission at the Army Salvage Depot, Fishermen's Bend. An extensive sale including Caterpillar, Cletrac, International Diesel Tractors, Elec. Generators, Elec. Motors, Chevrolet, Dodge, Ford V8, Motor Engines, Harness, Steel Shelving and Miscellaneous Equipment. J. H. Curnow & Son were the auctioneers. Catalogue has column for £, S and D down the right side of the page to write in the price of each lot. Contains a description of some lots. The back cover has a black and white photo of the entrance gates to the Commonwealth Disposals Commission Auction Depot. It has a clock in the top centre and two sets of double iron gates. The Prahran Telegraph Printing Co. were the printers of the catalogue.business, auctioneers, j h curnow & son pty ltd, ian dyett collection - auction catalogue - army salvage depot, commonwealth disposals commission, j h curnow & son, j l jamieson & co, w g wedd, the prahran telegraph printing co

The Rob Roy Hill Climb originated in 1935 on the property of former Heidelberg Mayor, William Clinton, where he reared the Rob Roy breed of miniature ponies. He established Pleasure Grounds on part of the property attracting groups of Sunday visitors from Melbourne's inner suburbs. Visitors enjoyed a picnic area, pony rides, a dance hall and a tap room. Young men would ride their BSA or Harley Davidson motorcycles to the property which led to regular club-organised hillclimb meetings between 1930 and 1936. In 1935 Clinton offered the use of his property to the Light Car Club of Australia for their hillclimbs. The track was sealed that same year and the hillclimb at Clintons Road was one of only three specially designed bitumen surface hillclimbs in the world, the others being Shelsey Walsh and Prescott Hillclimbs in the UK. The first Light Car Club of Australia hillclimb was held at Rob Roy in February 1937. Covered under Heritage Overlay, Nillumbik Planning Scheme. Published: Nillumbik Now and Then /​ Marguerite Marshall 2008; photographs Alan King with Marguerite Marshall.; p133 About six times a year the unlikely sound of car engines emerges from deep in the heart of Christmas Hills.* Usually a quiet retreat, the Hills are home to one of the world’s oldest purpose-built motor sport venues - the Rob Roy Hillclimb. When sealed in 1939, the hillclimb at Clintons Road was one of only three specially designed bitumen surface hillclimbs in the world, the others being Shelsley Walsh and Prescott Hillclimbs in the UK.1 The Rob Roy Hillclimb originated in 1935 on the property of former Heidelberg mayor, William Clinton, where he reared the Rob Roy breed of miniature ponies. Rob Roy was the Scottish folk hero and outlaw. On part of his property Clinton established Pleasure Grounds, attracting Sunday parties from Melbourne’s inner suburbs. Visitors enjoyed a picnic area, pony rides, a dance hall and a tap room.2 Young men riding on their BSA or Harley Davidson bikes led to club-organised regular hillclimb meetings, between 1930 and 1936. In 1935 Clinton offered his property to the Light Car Club of Australia for their hillclimbs. In February 1937, the first Light Car Club of Australia hillclimb meeting was held at Rob Roy. Jack Day achieved the fastest time that day for the 760 yard (695m) track at 36 seconds in a Ford V8 engined Bugatti Special. At first the climb was just a dusty gravel track, but in 1939 it was up-graded and bituminised. Today the 695 metre track begins on a slight incline, proceeds through a sharp right turn, which formerly passed a rusty iron shed, now remembered by the name Tin Shed Corner. The track continues down a slight incline to a level stretch along the top of an embankment holding back a half-acre (0.2ha) dam, then up to a one-in-three gradient. The track then winds uphill through several left turns to the finish line. In 1939 Frank Kleinig reduced the record to 29.72 seconds in an MG Hudson. Throughout World War Two the Rob Roy Hillclimbs were suspended, but were resumed in 1947. The hillclimbs consistently attracted crowds averaging 500 to 600 people, peaking at 2000, until the hillclimb was destroyed by the 1962 bushfires. The meetings included nine Australian Hillclimb Championships, with the first in 1938 won by Peter Whitehead in his ERA. Eight of the Outright and Class record holders were Australian Grand Prix winners including Jack Brabham, who became a triple F1 World Champion. The Light Car Club of Australia held 61 meetings at Rob Roy. Events usually included Touring, Gran Turismo, Production, Sports, Racing and Vintage cars and in the latter years Go-carts. These meets suddenly stopped after the 1962 bushfire destroyed the access bridge on the property leading to the track area, although fortunately Clinton saved his home. The club then established the Lakeland Hillclimb venue close to Lilydale.3 From 1979 to 1987 the MG Car Club ran hill climbs at the Templestowe Hillclimb until the land was to be sub-divided. In 1991 the MGCC approached the Shire of Nillumbik about using the derelict Rob Roy venue. In 1992, after much lobbying, the club signed a ten-year lease from Melbourne Water, which has been renewed. The original track was faithfully reconstructed. Access roads were improved and guard rails were installed on the causeway. Permanent structures were rebuilt and tonnes of rubbish removed. This was made possible by an immense amount of voluntary work by MGCC members and financial support from the newly formed Friends of Rob Roy. In February 1993 the first Return to Rob Roy Historic Meeting was run with a huge spectator attendance of around 1000 enthusiasts. In September 2007, the Nillumbik Shire Council gave the hillclimb heritage protection. This acknowledged the property’s significant contribution to early Australian motor sport with its social connection to William Clinton and the local community.4 *Christmas Hills was named after emancipated convict and shepherd David Christmas, lost in these hills.This collection of almost 130 photos about places and people within the Shire of Nillumbik, an urban and rural municipality in Melbourne's north, contributes to an understanding of the history of the Shire. Published in 2008 immediately prior to the Black Saturday bushfires of February 7, 2009, it documents sites that were impacted, and in some cases destroyed by the fires. It includes photographs taken especially for the publication, creating a unique time capsule representing the Shire in the early 21st century. It remains the most recent comprehenesive publication devoted to the Shire's history connecting local residents to the past. nillumbik now and then (marshall-king) collection, rob roy hill climb, clintons road, light car club of australia, william clinton

Digital TIFF file Scan of 35mm Ilford HP4 black and white negative transparency, c.1971george coop collection, lake goldsmith steam rally, steam rally, beaufort (vic.), steam traction engine, chrysler 75 roadster, ford model t, john fowler & co. (leeds) ltd

Near Eltham Park (now known as Eltham Lower Park), floodwaters from the Diamond Creek cut off the Main road into Eltham at Bremner’s Flats (present day Wingrove Park). In the distance, left of centre, is Mr. Montieth's Ford Wagonette stranded in the floodwater near Wingrove Cottage. “On the Lower Eltham Reserve the water was nearly five feet deep across the reserve and over a mile along the road. All the week-end shops are surrounded. For over 40 years flood waters have not reached this unprecedented level.” - Advertiser, Friday November 30, 1934, p7 "Whilst we were at the shop a "tidal" wave occured . There used to be a Mr. Monteith who ran a Model T Ford bus from the Eltham Railway Station down the main street. The bus would hold seven, six seated in the back, 3 aside a seventh standing on the step on the middle of the back hanging on to two small hand rails. The bus was caught by the flood and was abandoned not far from our shop in the paddocks towards the Higher Elementary School. It was there for days and after the flood waters receded, Mr. Monteith, after removing all the mud and debris gave the engine one turn with the handle and it started first time! So the story goes! " (Doug Orford Reminiscences, 2004) The 1934 flood of the Diamond Creek and Yarra River is the highest recorded flooding in the district and set the standard for the current planning flood plain level.Black and white photograph showing the floodwater from Diamond Creek across Main Road in 1934. Left of centre shows Mr. Montieth's Ford Wagonette in the floodwater in the distancefloods, main road, eltham south, diamond creek (creek), wingrove cottage, wingrove park, bus services, bremner's flat, eltham park, ford wagonette, mr. montieth, floodwater, reminscences

Ford Customline, registration no. GKL 204, circa 1956Customline 1956. M.T.S. Engine # ASQ 4984. Sold 23.12.57 750 pounds. P. Wilsonpolice vehicles; motor transport branch; wireless patrol; ford customline car

Inspector Reg Watson OIC Transport Branch far right.Ford Customline, registration number GUP 828, with four men in suits standing behind it. Circa 1958/59Engine AVQ2923. Sold 31.12.59 700 poundspolice vehicles; wireless patrol; motor transport branch; motor transport section; ford customline car

J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations. Herbert John Higgins ran a dairy farm with 40 cows on some acres fronting Jasper Rd ( Higgins Rd today ) he grew corn crops to feed his herd and also bought grain from J L Smith.Herbert Higgins , Dairy farmer, along with the Allnutt, and Long families were members of the Methodist Church Bentleigh from 1880s and involved in community organizations, J.L.Smith was an early settler in East Brighton now Bentleigh and established successful Wood cutting, Grain & Chaff cutting and Motor garage businesses in Centre Road . He was elected Councillor of the Shire of Moorabbin and, with Mary Ann, his family were involved with local Church, Red Cross, and other community organizations.Black & White photograph showing an upended Ford truck that has been overloaded with bags of grain with Herb Higgins and 2 men and a boy. They are outside J L Smith Chaff & Grain Store Centre Rd Bentleigh c 1926 higgins,herbert, dairy farmer, allnutt victoria (queenie), smith j l; smith mary ann, stanley helen, smith vic, smith harry redvers, chaff cutter, horse drawn carts, toll gates brighton, motor cars 1900, steam engines, early settlers, bentleigh, parish of moorabbin, city of moorabbin, county of bourke, moorabbin roads board, shire of moorabbin, henry dendy's special survey 1841, were j.b.; bent thomas, o'shannassy john, king richard, charman s, highett william, ormond francis, maynard dennis, market gardeners, vineyards, orchards, methodist church bentleigh, milk,

Photographed by Alison Kelly while she was joint caretaker of the building during the Mission Arts Centre days 1987 to 1991 Port Melbourne Missions to Seamen building, view from southeast corner of ground. Portion of Commonwealth Engine Works just visible at right, 1984 Ford Laser parked in circular driveway near front entrance. From album of photos mostly by Alison Kelly:missions to seamen, built environment

Malcolm Moore No. 1015 One of a Batch of 92 such rail tractors built. Builders Number 1015. Built for the Australian Army in 1943 Built for the Australian army - delivered to Army on the 3 March 1944 and was sold to the State Rivers and Water Supply Commission at Red Cliffs, Victoria. - used at the Red Cliffs Power station to haul briquettes from the rail siding Red Cliffs to the Red Cliffs Power Station and also used for shunting and some haulage from the Red Cliffs siding.. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It arrived at the Museum from Red Cliffs in 1977 and is operational. Originally equipped with a Ford side valve V8 Later replaced by a Fordson Major diesel tractor engine.Historic - Narrow Gauge Industrial Railway - used by the Australian Army, and the State Rivers and Water Supply Commission at Redcliffs, Victoria, AustraliaMalcolm Moore No.1015 - Malcolm Moore Rail Tractor 0-4-0 Malcolm Moore Rail Tractor - Steel (Painted)Malcolm Moore Rail Tractor 0-4-0 Malcolm Moore 2' Gauge 1015puffing billy, malcolm moore, ford v8, rail tractor, fordson, australian army, state rivers and water supply commission, 2' gauge, industrial narrow gauge railway

Fordson Henry Ford set up the company Ford and Son in 1917, it later became known as Fordson. Henry had previously tried to interest the directors of the Ford Motor Co in producing agricultural machinery, but when this met with no success he set up the new company to market the tractor he had created. Fordson: Model N 1929-32 Produced at Cork 1932-1945 Produced at Dagenham The Fordson Model N replaced the Fordson Model F. Production of the Model N started in Cork in 1929. Production of the Fordson Model N was transferred from Cork to Dagenham in 1932. The Model N featured a 27 HP engine, standard rear fenders (mudguards), a higher voltage ignition system, and optional pneumatic tires. In 1935 power take-off (PTO) was available as an option on the Model N. Historic - Farm Machinery - TractorSteel Tractor - Orange with black wheels.Fordsonpuffing billy, fordson, tractor

Malcolm Moore No. 1013 Four wheel Diesel Rail Tractor Gauge 2'0" Malcolm Moore rail tractor (Builder’s Number 1013) It was built for the Australian Army in 1943. It was sold to the Inkerman Sugar Mill in Queensland around 1948 for hauling cane and shunting at the works. This rail tractor was originally powered by a Ford side valve V8 petrol engine. It was purchased from the Inkerman Mill of Pioneer Sugar Mills in 1982. Historic - Industrial narrow gauge Railway - Diesel Rail Tractor - used by the Australian Army and Inkerman Sugar Mill in QueenslandDiesel Rail Tractor made of iron and wrought irondiesel rail tractor, puffing billy, inkerman mill, industrial narrow gauge railway, gauge 2’0”, inkerman sugar mill, australian army

Continuous cutting chain was patented in 1905 by Samuel Bens of San Francisco, while the first portable chainsaw was developed and patented in 1918 by Canadian millwright James Shand. But the main advancements of modern petrol chainsaws occurred in Europe in the 1920s and 30s where Andreas Stihl is often hailed as the "father of the chainsaw" After the second world war lighter materials, metal alloys and improved engine designs revolutionised the logging and timber industry. Of interest on this model is the spacing of the teeth compared to modern machines. With a 4HP motor it has few safety features and is very heavyEarly model chainsawBurns ChainsawModel 106forest harvesting

Les Solomano tells us this unit was made by their cousin Frank Solomano and mounted on the passenger side running board of his A Model Ford, Spare bads of charcoal were tied to the rear door, so passengers had to get in and out through the driver side doors. It is the smallest Gas Producer unit we have seenThis Gas Producer unit is obviously a home made construction for a specific application. Absence of any air-cooling facilities suggests these may have been fitted separately inside the engine compartment.No specific marlings

Ford and McFarlane shearing handpiece c.1890. This shearing handpiece is from ‘Wellington Lodge” in Tailem Bend, South Australia. Wellington Lodge today is an Angus beef farm; however, the property has a long history which includes wool farming. Wellington Lodge has been in the McFarlane family since the 1840’s and was originally around 19000 acres. The donor, Brian Licence, assembled this handpiece out of spare parts he found while classing wool on the property in the 1960s. Brian showed the finished handpiece to the owners once his classing work was completed and was told he could keep the handpiece as a souvenir. Brian also classed wool at “Jockwar” and “Pleasant Park” in Penola for members of the McFarlane family during the 1960s. The handpiece is named after Ford, the name of the engineer who designed the handpiece and McFarlane, the owners of Wellington Lodge Station and employers of Ford. This handpiece was developed as a prototype for use on the property. The handpiece which is made of solid brass is in a “used condition” and has been patched with solder. The handpiece is stamped with the number 10. Internally, the handpiece is powered from a drive mechanism of compressed air, this compressed air was typically produced by burning mutton fat. The handpiece comes from the pre-electrical– steam engine era of shearing. Brass metal shearing handpiece. A three-pronged fitting to hold both the comb and the blade protrudes from one end. A cylindrical stem extends vertically from the other. This is likely where a connecting rod to the shearing plant would be found. Below this vertical stem, the handpiece has an additional threaded hose fitting. This is likely where compressed air was delivered into the handpiece. The inscriptions can be found on the rear, near the previously mentioned vertical stem. Around this stem is also where the repairs of solder can be found. These repairs are unique to this handpiece and are not common practise.Etched. Base of handle. “FORD & McFARLANE . SHEEP SHEARER . Etched. Base of handle. “10”sheep shearing, shearing equipment, ford & mcfarlane, wellington lodge, tailem bend, south australia, shearing handpiece, shearing

The vehicle is a Ford F350 series, manufactured in 2005. It has a 6.5 litre V8 diesel supercharged engine. It was fitted out as an ambulance in Tamworth , New South Wales by Jacab and was one of many used in Regional Victoria in the early 2000's. This ambulance was stationed at the Heywood Branch in the west of Victoria for its entre service life until it was donated.Four-wheeled vehicle fitted out as an ambulance. Bodywork painted white with red logo and markings. Bumpers are chrome. Strip-lights mounted on roof above front windscreen. Registration number UDZ591ambulance, motor vehicle, ford, ford f350, jacab

1930 AA Ford 1.5 tonne (30cwt) truck. Originally owned by Blakiston & Company, Geelong. Built in 1930, this truck carried wool and general goods in Geelong and the Western District until the early 1940s. It was restored in 1989-1990 by David Malkit Automotive, Belmont, Geelong East Technical School. Specifications: 4 cyclinder side valve engine 201 cu.in. capacity 24 hp (R.A.C.) rating 40 bhp @2200rpm Optional 4 speed non-synchronised gearbox Heavy duty rear axle with torque rod Transverse front springs Cantilever back springs Coach built cab and tray bodyDark green truck with painted lettering on door and tray. The cabin has a black bench seat, and body has a wooden tray.printed: NATIONAL WOOL MUSEUM / GEELONG / BLAKISTON & Co. / Pty. Ltd. / CARRIERS / GEELONG / No 1 Licence plate: WOOL - 30ford, truck, transport, 1930s, vehicles

The VN Commodore was available in Executive, S, SS, Berlina and Calais specification levels, although a more basic SL model (opt. code A9K) was supposedly offered to government and fleet buyers, as it was not officially listed as part of the Commodore range. Changes in the relative values of the Australian dollar, the Japanese yen, and the US dollar made it impractical to continue with the well-regarded Nissan engine of the VL. Instead, Holden manufactured their own 90-degree V6 based on an old Buick design from the US, although initially it was imported. The 5.0-litre V8 remained optional and received a power boost to 165 kW (221 hp). Both these engines used multi point GM EFI and the V6 using 3 coil-packs for ignition. Holden and HSV developed this car as the basis for racing in Group A Confederation of Australian Motor Sport events. While the minimum number of cars built to qualify in Australian Touring car Championships, with modified body kit, brakes or engine is 500, only 302 VN were built but CAMS granted an exemption allowing them to compete.Holden and HSV had worked hard to develop this car to be a serious competitor to the Skyline, Ford Sierra and the BMW which had dominated in the previous years. This was to be the Holden’s answer and coincided with the return of Peter Brock back to the Holden team from 1987.Mechanically the cars were fitted with reworked version of Holden’s 4.9 litre V8. The engine block was cast for additional strength, modified cylinder heads roller rockers and high fuel flow fuel injection was applied. Output was 215 kw at 5200revs and, though at today’s standard, that is not that much it was very impressive at that time. The drive was through a six speed ZF gearbox with a heavy duty racing clutch and a limited slip differential.Under the Hawke government's Button car plan, which saw a reduction in the number of models manufactured locally, and the introduction of model sharing, the VN Commodore was rebadged as the Toyota Lexcen, named after the late America's Cup yacht designer, Ben Lexcen. Subsequently, the Toyota Corolla and Camry were, similarly, badged as the Holden Nova and Holden Apollo.Red executive 4 door sedanHolden Lion and stone emblem grille centre, Commodore boot LHS, Lion and stone emblem boot RHS.vehicle, vn commodore, holden, car