Four metal goldmining pans Nilgold pans, gold mining, gold mining tools

A mining safety cage was used in a mine lift. It was fitted with mechanisms to prevent the cage from dropping if the lifting rope broke. In the 1870s in Victoria, deaths and injuries from falling cages in vertical shafts of gold mines were a major problem. The inventor of this safety cage was Robert Allan, a machinery maker of Creswick Rd, Ballarat. He said his cage featured a ‘dissolving’ fulcrum. Others called it an eccentric (off centre) system. Note the pair of clutch levers designed to grab the side guides if tension ceases in the suspending rope from the poppet head pulley. Also, the hinged ‘lids’; designed to protect miners trapped in a braked cage from falling rope, and to enable rescue of the miners. This model was presented to The Ballarat School of Mines Council in November 1876. This model was shown at the Smeaton Show in November 1874, Ballarat School of Mines Museum from 1876, and examined by the 1879 Victorian Board of Inquiry (Pg 15 of FedUni Catalogue 3437) From the Argus of 13 November 1874: At Smeaton Show, Robert Allan of Ballarat won 1st prize for a Model of a Mining Cage, a Butter working machine, a Cheese press and a Curd Mill. By 1878 an Allan Safety-Cage was in operation in the Number 6 shaft of the Band and Albion Consols mine in Ballarat. This cage was judged the best inspected by the Victorian Board of Inquiry by 1879, p. 39.Mining was a big industry in Ballarat in the late 1800s and a lot of deaths were recorded because of mining accidents, the development of the mining safety cage brake limited the deaths and injuries from falling cages in vertical shafts. The model also has links to the Ballarat School of Mines, being presented to the council in 1876. Ballarat School of Mines is the oldest Technical School in Australia and is a predecessor of Federation University. The model is significant to Ballarat's mining history.Model of a mine safety cafe. A grey painted wooden frame with metal model of cage and safety brake system. When tension ceases in rope a pair of crutch levers grab strongly onto the wooden guide strips which run down the sides of a vertical shaft. This safety cage was discussed in "Safety Mining Cages. Report of the Board of Enquiry on Safety Cages 1878-9; together with proceedings of the Board and Appendices".safety cage, mine cage safety brake, robert allan, model, safety cage model, machine maker, millwright, mining, gold mining, tools, equipment, victorian board of inquiry

A gold pan was used to wash alluvial gold from gravel and dirt.Colour photographs of a large gold pan.gold pan, mining, gold mining tools tools

Photograph included in book "Victoria: Gold and Minerals" issued by Mines Department Victoria, 1935Photographvictoria, underground drilling, pneumatic drill, rail tracks, hand pushed cart, gold mining, mining, tools

Photograph included in book "Victoria: Gold and Minerals" issued by Mines Department Victoria, 1935Image of two men involved in panning for gold. victoria, gold mining, prospecting method, creek bed, panning, gold panning, gold pan, mining, prospecting, tools

The Old Identities Association was the forerunner ofThe Old Colonists' Association. This particular medal was presented to R.W. Wright who arrived in Ballarat in August 1853. It was purchased by the Old Colonists' Association in 2014. Other known medals were presented to :- * Arthur Croft who arrived in 1852 (Museum of Victoria) * Isaac Croft who arrived in September 1851 (Gold Museum) * Ben Story (Ballarat Historical Society) * John Brokenshire (Private Collection)Ballarat Old Identities medal in a box. The medal shows a gold cradle and other mining tools, and was presented to members of the Old Indentities Association. To qualify as a member you had to have arrived in Ballarat between 1851 and 1854. "Mr Welch, jeweller, of Sturt street, has just manufactured 60 medals, for issue to the members of the Old Identities' Association of Ballarat. Each is suitably inscribed and ornamented. The medals will be on view to day in Mr Welch’s window. " (Ballarat Star, 11 October 1884)The Old Identities Association 1851-1854 Arrived Aug 1853 R.W. Wrightballarat old colonists' association, ballarat old colonists' club, old colonists' association, ballarat, ballarat old identities, r.w. wright

Formerly KV 071. It was used to break up rock and ore, making it easier to extract valuable minerals. The pointed end of the pick axe was used to chip away rock, while the flat end was used to strike the rock for breaking it apart. This one has a short handle. Miners picks were commonly used in the the 19th and early 20th centuries for extracting gold from underground mine tunnels.Used in the Kiewa Valley where prospecting for gold occurred.Formerly KV 071. Cast iron symmetrical pick tool on cast iron with a wooden handle. It has a pointed end and a flat end. It is 12 inches long.gold mining, miners' pick axe, hand tool

This is a pictorial history of the Crooked River district.This is a useful reference tool on the history of gold mining in the Dargo area.A thin 56 pp paperback book titled,"Dargo Crooked River a Pictorial History". On the yellow front cover is a sepia photograph of a man standing outside a rough wooden hut. The title and author are printed in black text over this. The book contains Black / white photographs and the history of Dargo and Crooked River. The information is divided int decades. Inside there is a newspaper cutting of Victorian cattlemen on Junction Plain near Omeo.dargo-crooked-river gold-mining east-gippsland-history

The Rising Sun Reef first opened, at Bonang in 1868.– at Goongerah Creek south west of Bonang. William Hunter (1893-1971), resident of Tatura and Mallacoota was a soldier, surveyor and amateur naturalist. This document is a useful research tool.Plans and application for the "Rising Sun Goldmine". Tery are on foolscap sized white paper with black text. hunter-william gold-mining rising-sun-goldmine bonang

Metal shaft bucket hook, used in gold mining. Metal ring on top , locking device to secure bucket on shaft of object.gold mines, mining equipment, shaft bucket hook

Brass weights used for weighing gold. Smallest weights a 4 'grain' and 5 'grain' square weights. Rectangular 1 pennyweight weights (brass lozenge apothecary style weights ) through to round, flat 2 ounces. Weights enclosed in an oval shaped tin with side clasp.gold mining, scales, brass weight for weighing gold

Metal candle holder, cylindrical, open top and bottom, with metal spike attached. Used by underground miners. Candle holder was stuck into timbers or rock to provide light. Small stub of candle in holder. Wick fraying.gold mines, mining equipment, candle holder

Chinese gold scales. Wooden scale holder (a) two part wooden device secured at end of handle with a metal pin to allow swivelling of both pieces. At end of handle, two pieces 'violin' shaped to hold scale and weights. This enabled placement of scales within holder. Bottom piece has indent for scale pan, weight and long handle. Chinese scale (b) thin cream handle marked with inch graduations, without numbers. Separately suspended from handle with thick cotton is a small semi-circular lead weight and a round brass scale pan.gold mining, mining equipment, chinese gold scales

Cast Iron gold mould. Mould used in gold pour to shape ingot. Rectangular shape mould with rectangular handle.gold mines, mining equipment, gold mould

Cast iron mercury bucket, used to hold mercury, potentially in the process of recovering minute pieces of gold mixed in soil and sediments. See research page for description of one process of using mercury to extract gold.gold mines, mining equipment, mercury bucket, miners used mercury in a number of ways to amalgamate gold, with each mill or battery operator having their preferred method depending on the nature of the ore. by the late 1850s the most common way of crushing goldbearing quartz ores or consolidated alluvial cements was in a stamp battery. the battery featured heavy iron stamp heads held in a frame, with each head often weighing up to 500 pounds (226 kg) or more (see msv 1880, page 45) (birrell 2005). stamp heads were lifted and dropped by a rotating overhead cam shaft driven by a steam engine or water wheel. ore was fed into a large cast-iron battery box, mixed with a steady stream of water, and pulverised by the stamp heads. in some batteries, mercury was placed in the base of the boxes to amalgamate with freed gold. the violent agitation of the mercury in the mortar box, however, could cause the mercury to break into myriad tiny globules that were carried away by the water with the tailings, thus losing a certain amount of gold in the process (thompson 1867; ritchie & hooker 1997). the water and sand slurry was splashed by the falling stamps from the box through fine mesh screens and onto inclined wooden tables below the mortar box (figure 2). the tables were covered with copper sheets or plates coated with mercury, which caught and amalgamated with a portion of the gold. the grey putty-like amalgam was periodically scraped off the sheets and retorted in a furnace to collect the gold and recover the mercury for reuse. mercury was inevitably lost from the plates, while poor maintenance resulted in further losses of gold and mercury in the tailings. mercury use and loss from gold mining in 19th century victoria. peter davies1, susan lawrence, and jodi turnbull, department of archaeology and history, la trobe university.

Metal gold retort, it has a two parts circular container attached to crook shaped long handle. A caption reads Mr. G. Humphrey. An amalgam (gold and mercury) is placed inside and fire built around outside. Mercury vaporizes away leaving the gold. Diameter of retort 23 cm. Overall size 37x75 cm.mining, equipment, retort

Cast iron company seal used by the South Deborah Gold Mines for official documents including shares, painted black with wooden handle and gold embellishments, painted on one side Sth.Deborah in white paint.gold mines, mining equipment, company seal, bendigo-companies-gold mines-south deborah

Black cast iron company seal for Deborah United Gold Mining Company used for official documents including shares, black enamelled cast iron with gold trim, painted on one side Deb United in white paint.gold mines, mining equipment, company seal, bendigo-companies-gold mines- deborah united

Black enamelled cast iron company seal for the Napoleon Reef Gold Mining Company used for official documents including shares, with gold trim and Napoleon Reefs.NL and Nap.Reef painted on sides in white paint.gold mines, mining equipment, company seal, bendigo-compaines-gold mines-napoleon reef

Black enamelled cast iron company seal for the Central Garden Gully Gold Mining Company, with gold trim and C.G.Gully painted on one side in white paint.gold mines, mining equipment, company seal, bendigo-companies-gold mines-central garden gully gold mining company

Black enamelled cast iron company seal for the Monument Hill Consolidated (Bendigo) mine, with gold trim and the name Mon.Con painted on one side in white paint.gold mines, mining equipment, company seal, bendigo-companies-gold mines-monument hill

Black enamelled cast iron company seal for the North Virginia Gold Mining Company with gold trim and the name N.Virginia painted on one side in white paint.gold mines, mining equipment, company seal, bendigo-companies-gold mines- north virginia

Large black enamelled cast iron company seal with wooden handle, red and gold decoration, seal is a general cross hatched pattern.gold mines, mining equipment, company seal, bendigo-companies-gold mines-seals

Miner's pick, badly rusted iron in poor condition, no handle. Pick was found in the Whipstick bushland by a gold prospector.bendigo, mining, pick

A small 12oz weight made by a British company in West Bromwich called Archibald Kenrick and Sons. This was found by QC Binks whilst he was out metal detecting for gold.bendigo, gold mining, qc binks, archibald kenrick and sons, qc binks, weights.

Document. 2 page list of inventory.McColl, Rankin & Stanistreetorganization, business, nell gwynne reef mine, mccoll, rankin & stanistreet, nell gwynne reef n/l, gold mining, inventory of stores & tools

This photograph was taken in approximately 1870 and depicts four male miners standing in mining sluice at the Three Mile Goldfields. These men are wearing typical attire for 1870s gold miners. They wear white shirts, tan coloured pants with water proof shoes and most of the men are wearing an apron to prevent their clothing from becoming too dirty from the mud. Each man is wearing a wide brim hat and hold large wooden tools used for sorting through the sluice. Three of the four men have full beards. The photograph was donated to the Burke Museum by R. Ziegenbein before 2001 but the photographer and the individuals captured in the photo are unknown. The image depicts the landscape of the Three Mile Goldfields during a period when open cut sluicing was undertaken to reach gold. Open cut sluicing is a method used to extract gold and other precious metals from beneath the surface of the earth. This technique involved the use of high-powered hoses which broke down the soil enabling miners to come along and search this soil for gold. After the gold rush of the early 1850s, diggers had to enlist the assistance of heavy machinery and techniques like hydraulic sluicing in order to reach gold because the surface alluvial gold had already been discovered and removed. This heavy machinery was not used until after 1853. The Three Mile Goldfields was a site of rich alluvial gold deposits located about 5 km south of Beechworth in Victoria. Today, the location of this gold deposit is called Baarmutha. It was a popular area for gold mining in the 1850s but became largely abandoned by the following decade. In 1865, a man named John Pund recognized that the area could be potentially rich if a better water supply could be obtained. He secured a 15 year license with three other miners. Within the next five years, these men had constructed 19 km of water race going from Upper Nine Mile Creek to Three Mile Creek. By 1881, these four men had delivered 950,000 gallons to the Three Mile Sluicing area which is depicted in this photograph. Pund was later go into partnership with John Alston Wallace who would become owner of the Star Hotel in Beechworth. The Three Mile sluicing location continued to be operational until 1950. Sluice box workers were a vital part of gold mining regardless of how inefficient they were in the recovery of gold. After using hydraulic sluicing to cut away the earth, miners would use the big wooden boxes depicted in the image to catch the earth which would then be sifted for gold. However, accidents would occur often which would result in the gold washing away and unable to be recovered. It was not a very efficient system because the gold, which was alluvial and thus very fine, would often pass through the sluice box undetected.The search for gold is ingrained into the history of Victoria and therefore, images like this one which portray an open cut sluicing site can reveal important information for society and technology for the date when the photograph was taken. This image is of important historical significance for its ability to convey information about sluicing and the methods used to find gold in the late 1800s and early 1900s. It also shows a location where sluicing was undertook which provides insight into the impact of sluicing on the environment at a time when it was done. Images, like this one, of Australian gold rush history can reveal important information about the social and environmental impact of this period. This image depicts diggers standing in a mining location and therefore, this image has the capacity to reveal or support significant information for researchers studying the fashion and social status of diggers in Australia in approximately 1870. It can also provide information on the landscape of Australia in this period and the impact of mining for gold on both society and the Australian landscape. The Burke Museum is home to a substantial collection of Australian mining photographs which can be used to gain a deeper understanding into life on the gold fields, technology used in mining, the miners themselves and the impact of the gold digging on the environment.Sepia toned rectangular photograph printed on matte photographic paper and mounted on board.[illegible] about 1870 / 97 2514.1 / 2594 30three mile goldfields, goldfields, 1870, 1870 gold, australia, australian landscape, miners, gold miners, diggers, gold diggers, beechworth, victoria, sluice box workers, sluicing, sluice, mining