Very old. Ref. Pages 6 and 7 Tools for all Trades Catalogue. The braces vary in quality (strength) depending on what materials are used to make them.The brace is a hand operated tool for boring holes in wood, consisting of a crank-shaped turning device. The brace that grips and rotates the hole-cutting tool, the bit.Used by woodworkers in the Kiewa Valley.Vintage hand drill braces. All different and not all complete. Made of cast iron, steel with wooden handles. The drills fit into one end of the brace which is turned to make a drilling motion. A brace is a hand tool used with a bit (drill bit or auger) to drill holes, usually in wood. Pressure is applied to the top while the handle is rotated.brace and bit, woodwork, hand drilling

Before drills and braces, T-shaped augers were used to poke holes into wood, while smaller gimlets were used to start them.. A significant advance on the auger was the brace, which was originally designed with a single, permanently fixed bit at its end. Hand drills were often called eggbeater drills for their similarity to that common kitchen tool using a crank to drive the drill into the wood A steel hand drill with hand crank and wooden handlespioneers, early settlers, market gardeners, moorabbin, bentleigh, cheltenham, brighton, tools, craftsman, carpenters, blacksmiths, builders, farmers, metalwork, woodwork, drills

Historic - Industrial drill - typical hand operated design used in workshops.Historic - Industrial drill - typical hand operated design used in workshops.Hand operated drill press. Bench mounted type hand drill press. drill, press, workshop, hand operated, puffing billy

Historic - Industrial drill - typical hand operated design used in workshops.Historic - Industrial drill - typical hand operated design used in workshops.Hand Operated Drill Press Bench mounted type hand drill press. puffing billy, tools, hand tools, drill press

Hand Rail Drill Out on the track in the old days, it was sometimes required to drill some holes in a piece of rail so that two rails may be joined together by a metal joiner – called a fishplate. Before the use of generators and oxy cutting, the only way to do this was with a hand drill. This is the machine operated by two people, that would drill a hole in the rail. With two to three holes to be drilled in each rail end (ie 4 or 6 holes), it was a tiring, back breaking job. And then there was usually the rail on the other side of the track to be done! Historic - Railways Permanent Way and Works - track equipment - Hand Rail DrillHand Rail Drill made of metal puffing billy, hand rail drill

The invention of a hand drill is credited to Arthur James Arnot and William Blanch Brain of Melbourne, Australia who patented the electric drill in 1889. In 1895, the first portable handheld drill was created by brothers Wilhem & Carl Fein of Stuttgart, Germany. Hand-powered devices have been used for millennia. However, during the last quarter of the 19th century a radically improved generation of tools appeared. These tools took advantage of modern mass production machinery and processes (like interchangeable parts) and an increased availability in superior material (metal instead of wood). One of the outcomes included an array of new drilling machines. These human-powered tools were a vast improvement over earlier tools.This item is an example of a commonly used domestic tool - pre power tools.A Stanley hand drill with two wooden handles. The red wheel is painted metal. On red wheel - STANLEY ENGLANDwoodwork tool hand-drill

The Archimedes drill, also known as a fretwork drill, is an old type of drill which works on the Archimedian principle; the drill rotates quickly as the barrel on the stem is worked up and down. This tool provides a quick and easy way to bore holes through ordinary fret wood and other substances, smaller versions are used in jewellery making where precision drilling is required. There were numerous different sized Archimedes drills made from various materials, usually a combination of wood and steel, some being all steel and some including brass parts. The fancier versions of these drills included parts made from Rosewood, Ebony, Ivory and decorative brass parts. Some of the later Archimedes drills had technological improvements such as a ratchet device and the inclusion of fly-weights. The ratchet device allows the drill to revolve continuously in the cutting direction. The fly-weights give momentum to maintain the speed of the drill during the upward stroke of the hand. Most old examples such as the subject item have no makers names.A vintage drilling tool that gives a snapshot into how holes were drilled by hand into small or delicate objects during the Victorian era. Tools from this time are today regarded as collectable items eagerly sought by collectors of antique tools. Archimedean drill with Rosewood hand, brass bearings, steel twist and wooden grip. Noneflagstaff hill, warrnambool, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, archimedean drill, archimedean drill with wooden hand, drilling tool

This hand operated drill was used to drill holes in the rails so that with fishplates (metal joiners) the rails could be bolted together to form a continuous length.Historic - Railways Permanent Way and Works - track equipment - Hand Operated Rail Drill Hand Operated Rail Drill made of cast Metalpuffing billy, hand operated rail drill

Archimedes drills, incorporate a bobbin sliding up and down a spiral shaft to bore a hole. Spiral-bit augers were precursors to modern drills, whose bits cleared the hole of chips as the user drilled. Some of the most beautiful Archimedean drills appear in English tool auctions replete with brass, rosewood and even ivory. A steel hand drill with fine bit and sliding bobbin'HOBBIES' on top of handletools, metalwork, woodwork, carpentry, early settlers, pioneers, market gardeners, moorabbin, bentleigh, cheltenham, blacksmiths, bobbins, augers, hand drills, marples william

This item is an example of a domestic woodworking tool commonly used before the widespread use of power tools.A hand drill with three wooden handles. The main gear is painted red.On right handle - Made in China with some Chinese lettering.tool hand-drill

This style of geared drill was commonly referred to as an egg-beater drill and was first patented in 1838. During the late 19th century these drills became more common due to the development of mass production. Users also began to mount the drill onto a frame. This allowed greater control over the drill and removed the need to be holding it in both hands. This gave the operater greater control over the item to be drilled. The drill could be easily removed when required. This item is an example of a domestic woodworking tool commonly used before the widespread use of power tools. The construction of the basic wooden frame also demonstrates the ingenuity of early pioneers and tradesmen in adapting tools to suit their own needs.A metal hand drill which has been mounted on to an improvised wooden stand. hand tools, mass production, egg beater drills

Hand drill metal 3 wooden handles crank missing 310mmL x 145mmW. One handle greenflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Small hand drill with holding handle with a winding handle with " Leytool - made in England" Covered by Pat No. 20987/44 World PatentsAs abovetools, drill, leytool

Hand drill metal wooden handle plate painted red Stanley England on outside plate 00525 & 0108 on inside of plate 325mmL x 115mmWflagstaff hill, warrnambool, shipwrecked-coast, flagstaff-hill, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village

Wall mounted hand operated drill press. Flywheel on LHS. Drill lowering hand wheel on top. Painted green and black.Cast in relief on frame "Champion ......... & Forge Co./ Lancaster" on LHS, "Warranted" on RHS.trades, metal working

Small hand 'stanley' drill with red dial with a handle and a wooden knob. A '104' drill, has a handmade replacement handle.C0525 0255 on Dialtools, hand drill, stanley

The photo shows track construction in Dandenong Road by the PMTT in 1911. Note the hand drilling of the sleepers. It would appear to have been a hot day with most men having taken their jackets off. This photo appears in "Prahran and Malvern Tramways Trust - Melbourne's foremost municipal tramway" on page 46 and is credited to the Bob Prentice collection.Yields information about the methods of track construction during 1911 and Dandenong Road.Photograph, with a plain backtramways, pmtt, track construction, dandenong road

This tool is one of a collection of tools which are believed to have belonged to Henry Phillips. English-born carpenter, Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived for some time in Port Fairy before coming to Warrnambool where Henry formed a partnership with Christopher Beattie and established the undertaking firm of Beattie and Phillips in 1865. This firm continued on after the death of the two founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved in the management of the Mechanics’ Institute. This tool is of interest, firstly as an example of a vintage tool and secondly as a memento of the Warrnambool carpenter and businessman, Henry Phillips. This is a hand drill with a composite material handle at one end (for one hand) and a tubular metal piece at the other end for the insertion of a bit or drill. In the middle is a circular turning piece with metal spokes and a metal handle (for the other hand). The circular piece is held together and attached to the main body of the tool with several screws. vintage tools, henry phillips, history of warrnambool

This tool is one of a collection of tools that are believed to have belonged to the Warrnambool carpenter and businessman, Henry Phillips. English-born Henry Phillips (1821-1896) came to Australia with his wife Elizabeth in 1849. They lived for some time in Port Fairy and came to Warrnambool where Henry formed a partnership with Christopher Beattie to establish the undertaking firm of Beattie and Phillips. This business continued after the deaths of the two founders and lasted until the year 2000. In Warrnambool Henry Phillips was involved with the management of the Mechanics Institute. This tool is of interest, firstly because it is a good example of a vintage tool and secondly because it is a memento of the Warrnambool carpenter and businessman, Henry Phillips. This is a small hand drill with a metal piece containing a composite material handle at one end (for one hand) and a metal piece at the other end for the insertion of a drill. Attached to the main metal piece is a circular piece of metal with spokes and a wooden turning handle (for the other hand). The handle is attached to the circular spool by a metal screw. vintage tools, henry phillips, warrnambool, history of warrnambool

Yields information about the construction of trackwork and other Museum infrastructure during 1980.Letter from Dave Macartney to Warren Doubleday, typed on the rear of an Association of Railway Enthusiasts foolscap size train tour booking form for the Albury to Culcairn tour for 20/5/1967. Letter dated 20 May 1980 updates Warren on progress of bending rail, track repairs, purchase of a new Second hand drill and building work.trams, tramways, btps, trackwork, museum

This Yankee spiral-ratchet Screw Driver (screwdriver) set was a hand tool with drills, used in the making of components for the ship model Sovereign of the Seas. It is part of a collection of objects used by Jim Williams, maker of fine ship models from about 1930-1955. Most of the components for the models, as well as many of the tools, were handmade by Jim Williams. Jim’s family has donated the ship model “Sovereign of the Seas” and many tools, accessories and documents used in the making of this and other ship models have been donated to Flagstaff Hill Maritime Village. Ship model of HMS Sovereign of the Seas, scale model of 17th Century English war ship, was handmade and carved from plans, enclosed in airtight glass case. All components of that model, including even the smallest pulleys, were hand crafted using tools designed and made by Jim. Outstanding details include functional rigging and moving cannons. Please see our record 3732 of the mode Sovereign of the Seas for further details of the ship and the maker. This set is connected with the hobby and skill of ship model making that has been crafted as a leisure activity for many generations. The hobby is often chosen by serving and retired mariners who appreciate the connection with maritime history. This set was used by local Warrnambool man, Jim Williams, who was employed at Cramond and Dickson clothing store, and then at Fletcher Jones menswear for 27 years. It was used in making components for the model of the historic ship, the Sovereign of the Seas. The Sovereign of the Seas was a historic 17th century English war ship with important maritime heritage. Spiral-Ratchet Screw Driver set, also called an ‘American drill’ or hand drill. 9 parts, Yankee brand, No. 31 set. Made by North Bros. Mfc Co. Philadelphia, Pennsylvania, U.S.A.. Instructions for use are on label. Ratchet screwdriver plus 6 drill bits - sizes 1/16th to 11/64th - contained in a small round wooden tube with lid, label on outside. This Screw Driver set is part of a collection of tools and accessories once used by Jim Williams, maker of a series of ship models 1930-1955 including “HMS Sovereign of the Seas”. “WITH 6 DRILL POINTS / SIZES, 1/16 TO 11/64 includes - - with - - / “Yankee” Spiral-Ratchet Screw Driver No. 31 / Made by NORTH BROS. MFG. CO. PHILADELPHIA P [A?]- / Directions for use – First Insert Drill Point In - / Drill Chuck, and turn the – in Chuck of Screwdriver U.S.A.”flagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, jim williams, james bernard williams, ship model hobby, ship model tools, ship model making equipment, ship model making accessories, wood working tool, model making tool, screwdriver set, spiral ratchet screwdriver set, yankee screwdriver set, spiral-ratchet screw driver set, american drill, ratchet drill set, ratchet hand drill, ratchet screwdriverset, north bros. mfc co philadelphia pa, tool, sovereign of the sea, ship model, hobby, ship model tool

Wall mounted drill press, flat belt pulley driven. Flat belt pulley and flywheel on LHS, hand operated drill lowering mechanism on RHS. Unpainted.Cast in relief on main frame "No 1082" on LHS, "Buffalo Forge Co. / Buffalo N.Y." on RHS.trades, metal working

W E Coward builder came to Stawell around 1919 and had a workshop in Campbell Street Stawell. Tools kept by his son Frank Coward. Donated by grandsons Ron and Jeff Coward of Stawell. Ten Moulding Planes, Wooden Mallet, Woodworking Drills, Three rounded Chisels, Counter sink Auger, Scouring Tool, Spoke Shave, Sawblade Tooth setting tool, simple Caliper, Wooden Plane, Hand Drill, Moulding Plane with Offsets, Two Handled routing tool, Two flat Blade Screwdrivers Wood working tools including set of Moulding Planes, mullet drills etcSome tools have makers stamps on them

Iron and wooden brace for drilling holes. The U-shaped crank has a wooden spindle on it and along with the top spindle is allowed to freely turn under the hands without producing wear and tear on the hands. A drill bit is in the chuck.brace and bit