W. Dalle Mfg Co molde in the cast of the foot one side and opposite Patent Pending 1901.hose fitting, sprinkler, patent, 1901

Sad-irons or "solid" irons were made by blacksmiths and used to smooth out material by pressing the hot iron over it. A piece of sheet -iron was placed over the kitchen fire and the irons placed on it could be heated whilst remaining clean of ash.. The women used 2 irons - one heating while the other was used. Thick cloth or gloves protected their hands from the hot irons. The handle was removed from the cool iron and re- attached to remove the hot iron from the fire. The cool iron was replaced on the fire or stove to heat again. These irons were cleaned with steel wool to prevent them marking the material. If the iron was too hot the material would scorch. Most homes set aside one day for ironing and some large households had an ironing room with a special stove designed to heat irons. However, most women had to work with a heavy, hot iron close to the fireplace even in summer. Thomas Fletcher (1840-1903). By 1880s he had a gas appliance manufactory in Thynne Street, Warrington. By 1895 the company had become Fletcher Russell and Co Gas Engineers, his firm having merged with Alexander and William Russell of Pendleton Iron Works. Circa 1950, the firm merged into Radiation Ltd which was later acquired by 'TI New World'; 1902: Fletcher, Russell & Co. Ltd., Palatine Works, Warrington In 1880 gas -fuelled irons were connected by rubber tubing to the gas light-fittings of the house or to gas canisters. However , not many houses had access to a gas supply until much later and this iron was popular in 1920’sThese sad irons remind us of the difficult circumstances experienced in their daily routines by the pioneers and early settlers of Moorabbin Shire The family of Miss M Curtis were early settlers in Moorabbin Shire.A gas-fuelled flat iron, made in USA , It would have been attached to a gas hose fitting that was also used at night for light in the house. There is a small chimney to allow for air and to try to control the amount of heat in the iron. A 'shield' is under the leather covered handle to protect the user's hand from the heat, however it is made of copper metal - a heat conductor.FLETCHER RUSSELL CO. / LIM/ PATENT/ WARRINGTON on right side of handle 'Registered' on left side of handle ' Fletcher Russell Co L / Warrington, Manchester / & London.sad iron, kitchen equipment, fletcher russell co. ltd., england, warrington, manchester, pioneers, early settlers, market gardeners, sewing, craftwork, clothing, moorabbin, brighton, bentleigh, fireplaces, stoves, domestic gas supply, gas-light, gas cannisters

Advertising material for Stilwell's, Hargreaves Street, Bendigo. 1) four pages summer circular, Season 1937-38 items includes: garden hose, fittings and reels. Lawn mowers, blinds, outdoor furniture and fly doors. 2) Paint or perish! Advertising for various paint brands and wallpapers. 3) article from the Bendigo Advertiser January 1951 titled: the Story of Stilwell's a link with Bendigo's progress.bendigo, business, stilwell

Four invoices from Holman Bros. (Australia) Pty. Ltd. Collins House, 360 Collins Street, Melbourne, C. 1 to North Deborah G. M. Co. N. L.. Invoices are numbered:- 12360, 12363, 11442 and 11462. Invoices are mostly for hose fittings, also some bushings and pistons. Three lots of goods were sent by passenger train and the fourth by post. Dates are26th and 28th February 1951 and 20th February and 24th February 1950. Albert Richardson Collection. document, gold, north deborah g. m. co. n. l., north deborah g. m. co. n. l., holman bros. (australia) pty ltd, invoices to north deborah g. m. co. n. l.

Yearn Hunger Thirst Always on the edge of oblivion, craving sustenance in a dry land. McLean and Kennedy have collected dry materials: hollow pipes, old hoses and worn metal hose fittings. The materials were then wrapped with dyed, frayed fabric, string and yarn to create a piece that expresses the collective longing for rain.Wangaratta Art Gallery Collection. Winner of the Wangaratta Contemporary Textile Award 2019.A sculpture made out of recycled hoses and irrigation fittings that have been wrapped and tied in overdyed yarn, string, fabric stripswangaratta art gallery, wcta, sculpture, cheryl kennedy, linda mcclean

Ford and McFarlane shearing handpiece c.1890. This shearing handpiece is from ‘Wellington Lodge” in Tailem Bend, South Australia. Wellington Lodge today is an Angus beef farm; however, the property has a long history which includes wool farming. Wellington Lodge has been in the McFarlane family since the 1840’s and was originally around 19000 acres. The donor, Brian Licence, assembled this handpiece out of spare parts he found while classing wool on the property in the 1960s. Brian showed the finished handpiece to the owners once his classing work was completed and was told he could keep the handpiece as a souvenir. Brian also classed wool at “Jockwar” and “Pleasant Park” in Penola for members of the McFarlane family during the 1960s. The handpiece is named after Ford, the name of the engineer who designed the handpiece and McFarlane, the owners of Wellington Lodge Station and employers of Ford. This handpiece was developed as a prototype for use on the property. The handpiece which is made of solid brass is in a “used condition” and has been patched with solder. The handpiece is stamped with the number 10. Internally, the handpiece is powered from a drive mechanism of compressed air, this compressed air was typically produced by burning mutton fat. The handpiece comes from the pre-electrical– steam engine era of shearing. Brass metal shearing handpiece. A three-pronged fitting to hold both the comb and the blade protrudes from one end. A cylindrical stem extends vertically from the other. This is likely where a connecting rod to the shearing plant would be found. Below this vertical stem, the handpiece has an additional threaded hose fitting. This is likely where compressed air was delivered into the handpiece. The inscriptions can be found on the rear, near the previously mentioned vertical stem. Around this stem is also where the repairs of solder can be found. These repairs are unique to this handpiece and are not common practise.Etched. Base of handle. “FORD & McFARLANE . SHEEP SHEARER . Etched. Base of handle. “10”sheep shearing, shearing equipment, ford & mcfarlane, wellington lodge, tailem bend, south australia, shearing handpiece, shearing

Copy of a black and white photo of six fire brigade members with their championship shield. Notice above the shield has written on it: Menzies F. B. Championship Shield. three of the team are standing behind a table, two are seated at the front ends of the table each side of the shield and one is sitting on the floor holding the long tap. Two of the men at the table are holding an end hose fitting. The shield is a large round one with a circular piece in the centre with a fireman holding a hose. There are smaller shields surrounding the centre. Some keys? or fittings are at the top of the shield. The men are wearing long white trousers and long sleeve shirts buttoned up to the neck. A pot plant is on the left of the photo and the background is a garden scene.bendigo, history, long gully history group, the long gully history group - menzies f b

.1 25 year bar - white background red lettering .2 30 year bar - navy background silver lettering .3 40 year bar - yellow background silver lettering .4 45 year bar - gold background black lettering .5 Medal attached to red ribbon supported by metal banner. Medal is round, white background with navy in centre. Gold enamel images of hose pump fittings and other firefighting regalia are imposed on the front of the medal. A gold coloured metal insignia is pinned to the red ribbon. A pin on a swivel is attached, this pin is used to attach to clothing. .1 25 YEARS .2 30 YEARS .3 40 YEARS .4 45 YEARS .5 LIFE MEMBER is on top of red ribbon, CLUNES is on bottom of red ribbon/INSCRIPTION on reverse of medal "Presented to J. T. Hardin from Officers & Members Clunes Urban Fire Brigade in appreciation of service 5-9-1986" j t hardin, sevice medals

The Hydro mixer was attached to the kitchen tap which drove the mixing paddles.Mostly made of cast iron covered with green enamel. Its base is a 20 centimetre diameter and two centimetres high and shaped to hold a bowl, there is a protrusion eight centimetres long, four centimetres wide and nine centimetres high. A hinged section is attached to the protrusion of the base, it's a curved oval shape that's four centimetres by three centimetres at its base and tappers to four centimetres by two centimetres at the top, it then widens to an eleven centimetre diameter and three centimetres high shape that is parallel to the base, the centre of it is above the centre of the base. There is a removable eleven centimetre diameter plate screwed to the top. A two centimetre diameter 60 centimetre long plastic hose with a brass fitting on the end that is flared to four centimetres is attached to the side of the circular top. A one centimetre diameter metal tube is attached underneath that has two beaters on the end of it.HYDRO MIXER PAT APP FORfood preparation, hydro mixer

The design of this and other similar treadle powered dental engine (or dentist drill) was in common use by dentists from the 1870’s into the 1920's. When electricity became accessible to most communities the electrically powered dental engines began to take over from the treadle power. Over the ages teeth were extracted using picks and scissors and other gouging instruments. Bow drills, hand drills and even a "bur thimble" drill were later used to prepare cavities for filling. Some drills were made bendable by attaching flexible shanks between the metal bur and the handle, giving access to the teeth at the back of the mouth. Other mechanical devices were introduced along the way, such as clockwork drills, but they were hard to handle and inefficient. Over the centuries “dentistry has been performed by priests, monks and other healers. This was followed by barbers; the barber’s chair may well have been the precursor to the dental chair. “(SA Medical Heritage Society Inc.) In 1871 James Morrison patented the first commercially manufactured 'foot treadle dental engine', the first practica dental engine although others had been introduced as early as 1790 (by John Greenwood). Handmade steel burs or drills were introduced for dental handpieces, taking advantage of the significant increase in the speed of the drill. In 1891 the first machine-made steel burs were in use. The treadle drill reduced the time to prepare a cavity from hours to less than ten minutes. In 1876 the Samuel S. White Catalogue of Dentist Instruments listed a 12 ½ inch wheel diameter dental engine, with 14 bright steel parts, for sale at US $55 In today’s market, this is the equivalent to US $1200 approx. The specifications of that dental engine are very similar to the this one in our Flagstaff Hill Maritime Village’s collection. It is interesting to note that workings of a similar treadle dentist drill were used and modified to power a treadle spinning wheel of one of the volunteer spinners at Flagstaff Hill Maritime Village. The foot treadle dental engine was a milestone in dental history. “Historic importance of treadle powered machines; they made use of human power in an optimal way” (Lowtech Magazine “Short history of early pedal powered machines”) The invention of a machine to speed up the process of excavation of a tooth lead to the invention of new burs and drills for the handpieces, improving speed and the surgical process of dentistry. They were the fore-runner of today’s electrically powered dental engines. This treadle-powered dentist drill, or dentist engine, is made of iron and steel and provides power for a mechanical dental hand-piece that would be fitted with a dental tool. The drill has a three footed cast iron base, one foot being longer than the other two. A vertical C shaped frame is joined into the centre of the base, holding an axle that has a driving-wheel (or flywheel) and connecting to a crank. A slender, shoulder height post, made from telescoping pipes, joins into the top of this frame and is height adjusted by a hand tightened screw with a round knob. On the post just above the frame is a short metal, horizontal bar (to hold the hand-piece when it is not in use). A narrow tubular arm is attached to the top of the stand at a right angle and can move up and down. At the end of the arm is a firmly fixed, flexible rubber hose protected for a short distance by a sheath of thin metal. At the end of the hose there is a fitting where the drill’s hand-piece would be attached; a small, silver coloured alligator clip is also at the end. A treadle, or foot pedal, is hinged to the heel to the long foot of the base, and joined at the toe to the crank that turns the driving-wheel. There is a spring under the toe of the treadle. The metal driving-wheel has a wide rim. Touching the inside of the rim are four tubular rings that bulge towards the outside of the driving-wheel, away from the pole, and all meet at the hub of the axle. The axle is bulbous between the inside of the driving-wheel and the frame then passes through the frame and is attached on the other side. The driving-wheel has a groove around which a belt would sit. The belt would also fit around a pulley on the arm, at the top of the post. The pulley is joined to a rod inside the arm and this spins the drill's hand-piece and dental tool holder. The two shorter feet of the base are made from a long metal bar that has been curved outwards, and its centre is bolted to the base of the pole. Under the ends of the curved legs of the base are wedge shaped feet. The driving-wheel is decorated in light coloured paint on both sides, each side having three sets of floral decals evenly spaced around them, and each about a sixth of the wheel's circumference. Similar decoration is along the sides of the frame. The foot pedal has decorative cutout patterns in the centre of the foot and at the toe. On the long foot of the stand is some lettering with a fine, light coloured border around it. The lettering is hard to read, being a dark colour and flaking off. There are also remnants of fine, light coloured flourishes. The foot pedal has lettering of the maker’s trade mark cast into the metal at the ball of the foot. Lettering on the base is peeling and difficult to read. The foot pedal has a trade mark cast into it that looks like a combination of ‘C’ , ‘S’ , ‘A’, ‘R’. flagstaff hill, warrnambool, shipwrecked coast, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, dentist, teeth, dental drill, dental engine, treadle drill, foot powered drill, treadle engine, orthodontics, dental surgery, james morrison

A tank crew gas mask as issued by the United States of America army during World War 2. When correctly worn by the wearer there is a tube fitting at the rear of the head which was connected to a length of flexible hose to receive a fresh air supply.

One school of thought is that it is an Ausculater -similar to a stethoscope. Others think it is a Convertube to aid the hearing impaired. This is a conversation tube. It has a hose with black funnel shaped fitting on one end and a small fitting round fitting on other.shipwrecked coast, flagstaff hill, flagstaff hill maritime museum, maritime museum, shipwrecked artefact, warrnambool, ausculater, convertube, hearing aid

This water standpipe is believed to be the only one of its kind in working order. It was originally located in Warrnambool, on the hillside at the corner of Mickle Crescent and Banyan Street, providing water for the Chinese Market Gardens below, on the flats. It was removed from this location on May 2nd, 1979, with the intention to relocate it at the new Flagstaff Hill Maritime Museum & Village. The standpipe lay in storage for years until the Warrnambool Company, Chemblast, offered to restore it for use as a working display. The display was officially opened on March 31, 2014. The water from the adjacent lake is drawn out with a hand operated water pump, and goes up into the standpipe, where flows through the canvas hose and into the top of the Furphy Farm Water Cart. The display is a visual acknowledgement of the years served by Flagstaff Hill volunteer and Friends of Flagstaff Hill Chairperson, Bob Crossman. Warrnambool’s early settlers had no water supply prior to the mid-1850s. They relied on rain water tanks, domestic wells and springs. The town experienced a huge, destructive fire in William Bateman Jnr. & Co.’s large produce store in November 1856, which highlighted the need for both a fire brigade and a good supply of water. In 1863 a volunteer fire brigade was established. In August 1880 the town celebrated the installation of its first water standpipe on the corner of Liebig and Timor streets. The water was pumped from springs at Cannon Hill through the connected pipeline to the standpipe, then distributed to households via horse and cart. Each of the licenced cart drivers were compelled by Council regulations to keep their carts full from sunset to sunrise, ready to cart water to outbreaks of fire. They received a fee for this service. In 1893 the town installed a water supply, sourced from the Merri River, stored in a reservoir basin and tower in north Liebig Street, and distributed throughout the town in a system of pipes. By late 1939 a reticulated supply was installed, with the water piped in under the Otway Scheme. Standpipes are still used in modern times in rural and remote areas for homes, farms, stock, agriculture and firefighting. Many commercial or government owned standpipes are metered, charging a fee for the quantities of water supplied. This water standpipe was made by Langlands Foundry Co. Limited, Melbourne, which was establish in 1842. It was Melbourne’s first foundry and iron shipbuilder, and one of the largest employers in Victoria at the time. Langlands was known for its high quality workmanship and wide range of goods for mining, engineering, marine, railway and other industrial uses. The company made the first cast bell, the first lamp posts in the colony, and the boiler for the first Australian train. In the 1860s it produced cast iron pipes for the Board of Works, which laid the pipes for Melbourne’s first reticulated water supply. The firm was bought by Austral Otis Co. in 1897.This water standpipe is significant historically as it is believed to be the only one of its type in working condition. The standpipe is significant for being manufactured by early colonial firm Langlands Foundry of Melbourne, which was known for high quality, cast iron products. The firm made the boiler for the first Australian train, assembled the first Australian paddle steamer and made the first Australian cast bell and lamp posts. Langlands was one of the largest employers in Victoria at the time. The standpipe is significant historically as it represents the evolution of water supply services in Australia. Standpipe; vertical cast iron water pipe, painted crimson, fixed in position, tapering inward from the round base to the rectangular joint near the finial on top. A hexagonal pipe extends at right angles from the joint, with an outlet fitting and flow-controlling wheel on the end. A length of canvas hose hangs from the outlet fitting. Inscriptions are on one face of the joint. The standpipe was made by Langlands Foundry Company of Melbourne. Embossed “LANGLANDS FOUNDRY CO. / LIMITED / ENGINEERS / MELBOURNE”warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, flagstaff hill, standpipe, stand-pipe, water standpipe, fire standpipe, firefighting equipment, water supply equipment, chinese market gardens, banyan street, liebig street, water tower, bateman’s fire, working display, water supply, town water, rural water, reticulated water, cannon hill spring, merri river, otway water, water carters, horse and cart water supply, volunteer fire brigade, langlands foundry, early melbourne, iron works, bob crossman, late 19th century water supply

Ampol Wayne Petrol Bowser - metal, painted red top-half and blue bottom - back and front identical with authentic logos placed below the glass encaseddial showing quantity and cost of fuel dispensed. Above dial is smaller circular bowl showing fuel level. One side showing metal fittings for dispensing fuel and attaching hose and both sides have Ampol logos on lower half. Pump bolted to concrete pad for display.Silver plaque with "WAYNE" below dispensing dial. Decal 'showing "Ampol" logo' on all sides and 'BORON" front and back. Plaque reading 'THIS BOWL MUST BE FULL/BEFORE AND AFTER DELIVERY" on front and back under small bowl. Sticker reading 'THIS FUEL MAY CONTAIN/LEAD AND IS TO BE USED/AS MOTOR FUELD ONLY".ampol, petrol bowsers, service stations

Two brass fire hose nozzles and a fire hydrant lever.fire fighting, fire hose fittings

Hand operated pressure pump with water reservoir. High and low pressure hoses. Low pressure for filling reservoir, high pressure reinforced hose for delivering water to item to be pressurised. Brass fittings. Reservoir painted pale green and operating handle yellow & red.

BHS CollectionA Davis Tyre pump. A black metal cylinder four centimetres diameter and 48 centimetres long is attached to a metal plate four centimetres wide and 14 centimetres long. A one centimetre diameter, 50 centimetre long rubber hose is attached to the bottom of the cylinder has a metal fitting on the other end. The wooden handle on top of the cylinder is 17 centimetres long and three centimetres diameter, it has a one centimetre diameter, 44 centimetre long metal rood attached to the middle of it which goes into the cylinder and presumably has something on the end of it to push air through the rubber hose. The logo near the top of the pump is partly destroyed has on it - 02 (an unreadable word) DAVIS TYRE PUMP. (There is a picture of The Davis Cup tennis trophy in the middle) Partly destroyed on the bottom of the logo is - DAVIS INDUSTRIES AUSTRALIA Part of the Aileen and John Ellison Collectionaileen and john ellison, davis tyre pump

The Small Box Respirator (SBC) was a British gas mask of the First World War and a successor to the Large Box Respirator. In late 1916, the respirator was introduced by the British with the aim to provide reliable protection against chlorine and phosgene gases. The respirator offered a first line of defence against these. The use of mustard gas, was begun by the Germans; a vesicant ("blister agent") that burnt the skin of individuals that were exposed to it. Death rates were high with exposure to both the mixed phosgene, chlorine and mustard gas, however with soldiers having readily available access to the small box respirator, death rates lowered significantly. Light and reasonably fitting, the respirator was a key piece of equipment to protect soldiers on the battlefield.The Small Box Respirator ('SBR') proved to be the most effective gas mask produced during the First World War, and had a number of advantages over its French and German contemporaries.Canvas bag containing Small Box Respirator consisting of a rubberised fabric face mask, connected by a fabric covered rubber hose to a canister made of tin plate containing a chemical absorbent.gas mask, ww1

10934.30a - Notification of out-of-stock items. Receipt dated: 29 July 1954. pink cream, rectangular paper The receipt header reads "F.W. Milne & Son" in capital letters. Milne and Son were merchants and engineers. below the company name, it lists the company's: Address - Vine Street, Bendigo Contact Info - Phone 53 and 54 Handwritten in blue ink on a black typed template. For the purchase of leather belts. 10934.30b - Letter notification of altered discount. Receipt dated: 25th Sep 1953. large, cream, rectangular paper with a printed header in green and black ink. The receipt header reads "F.W. Milne & Son" in capital letters. Milne and Son were merchants and engineers. They sold Iron and steel, galvanised and steam piping and fittings, pumps, pulleys, transmission belting, bearings, shafting, air hoses, packings etc. below the company name, it lists the company's: Address - 52-60 Vine Street, Bendigo Contact Info - Phone 53, 54 and 1026 Typed blue ink on printed header. signed by the secretary in blue pen ink. 10934.30c and 10934.30d - business card Receipt dated: 1-2nd Sep 1954. tan - rectangular paper printed with business header in black ink. The Card reads: (10934.30c) F.W. Milne & Son. Merchants and Engineers. Vine Street, Bendigo. Distributors of: - Bearing Service Co. of Aust. PTY. and Stewarts & Lloyds PTY. LTD. Welding electrodes and welding equipment. Belting. Vee belts and Pulleys. Steel. Pipes and Pipe fittings. Steam valves and packings. British tube mills products. Electric motors. die cast and aluminium vee pulleys and motor pulleys. centrifugal pumps and pumping equipment. Petter diesel engines. Roseberry engines. Jap petrol engines. (10934.30d) Vine Street, Bendigo. Dear Sir, we wish to advise that our representative Mr. H.W. McMaster, will have the pleasure of calling on you on or about the 1-2 Sep 1954. Any orders entrusted to him will receive our careful prompt attention. bendigo, morton's stores, fw milne and son