150 p.; 21 cmnon-fictionReflections on the creative life of EE Kurthkurth kiln, ee kurth

The authors personal experiences visiting Kurth KilnKurth Kiln at the time the Friends of Kurth Kiln were formedTwo Page Article in the publication "Victoria's Heritage" by Mary Ryllis ClarkCopy shaded pink

Kith Kiln was the site of a short lived charcoal kiln designed to provide an alternative to petrol during World War 11 when there was a fuel shortage. Local history has been told by Genseric (Bill) Parker and the reflections collected by Friends of Kirth Kiln (under the auspices of Parks Victoria).The booklet is significant because it tells the story of the development of the Kirth Kiln Park in Gembrook, from the Friends perspective.The park is not only historical but is also of great environmental significance and it forms part of community life in the district. Green soft cover booklet of 128 pages. The front cover has 2 photos; the top one of the caretakers compound with Forest Commission huts and the bottom photo is of the Lake, taken from the dam on Tomahawk Creek. The back cover has a diagram of the Kiln logo.Fireside Stories with Genseric (Bill) Parker and Lorna Parker. Reflections collected by Friends of Kirth Kiln.kirth kiln, genseric parker, parks victoria, gembrook, charcoal burner

Although the Beenak Post Office officially closed on 31 August 1951, the Mail Box continued to be used until 1976. The history of Beenak (the town that never was) is part of the Yarra Valley Ranges, and this picture tells the story of the historic MailboxBlack and White Picture of the original Beenak Post Office Letter Box, used for collecting mail during the Beenak Sawmilling operations. The Friends of Kurth Kiln have errected a Commemorative Plaque on site next to the huge gum tree that still carries the scar where the the mail box had been mounted. A full scale replica of the box has been fitted to the shed at Kurth Kiln, made and painted by Henk Bouck under the supervision of ex PMG officer John Waghorn beenak, post office

Amongst Kurth Kiln Cultral Heritage Artifacts assumed left after the Foresty Commission moved from Kurth Kiln to Kalista LowManufactured rusty metal cutting blades attached to metal handle No physical markingsshears

found amongst the tools at Kurth Kiln Part of wood harvesting machineryChisel shaped tool for a machine with a 3.5cm hole at one end. 3cm thick and 6cm wide at the thick end. Could be part of a slasher or hammermillrural industries

found a Kurth Kiln amongst the charcoal making equipmentV Pulley Wheel 10cm diameter by 4cm wide, on a right angle steel shaft cirved and hooked for hanging. Bearing seized up

Professor Ernest Edgar Kurth of the University of Tasmania, invented a faster, simpler and cleaner way to produce charcoal on a continuous basis during the second world war. The charcoal was used to produce a combustible gas in motor cars, as a substitute for petrol, which was heavily rationed. The first batch of charcoal was produced in February 1942 and continued until the end of the war. Wood from stringybark trees was cut into lengths and fed into a kiln which converted it into charcoal. The Kiln is located on Beenak Road, 7km north of Gembrook. It has great historical significance, particularly as an alternative supplier of fuel during the second world war. It is a State Registered facility, managed by the Friends of Kirth Kiln and the park is managed by Parks Victoria Green soft covered book of 150 pages, with a photo of 2 men and a boy out in the bush with 3 fires burning.Contains a Prelude about Ernest Edgar Kurth written by Alfred Klink (2013) and a Foreward by John Sullivan (Heritage Officer of Parks Victoria). There is an Acknowledgement page, with recognition given to the grant provided by the Department of Sustainability, Environment, Water, Population and Communities. e.e. kurth, kirth kiln, charcoal kiln, parks victoria

Kurth's kiln used creek water in a series of waterpipes to cool the charcoal below the flash point for extraction during the charing processA cylinder of wood fitted on a 1" waterpipe, secured by an elbow and a 1" locknut. A 10cl long piece of pipe is fitted on the other side of the elbow. The assembly could be part of the kiln water-cooling system

The Unit was picked up from a paddock on a farm in Bagshot, near Bendigo. It was donated to the Friends of Kurth Kiln Heritage Collection by the Family of Cyril H Peatling on 23 December 2006.Gas Producer Units are of significance to Kurth Kiln because they demonstrate the enduse of the charcoal that was created at Kurth Kiln. Considerable documentation has been made available to us on its history, including a picture of the truck is was mounted on. A Gas Producer Unit that converted charcoal into a gas suitable for the combustion engine. Used on motor vehicles during WWII petrol rationing restrictions. It consists of a hopper to hold the charcoal and a firebox to generate the gasNameplate missinggas producer, bagshot, wilma

Specifically shaped hatchet with downward pointed blade and stubby short wooden handle 231 SCOTT Trojan

Part of Tools used for making charcoal during WWIIPurpose made Steel Clamp for attachment to to round shaft up to 5cm. Threaded section with "T" bar for tightening: Height 16cm Width 11cm, Depth 5cm Dia of shaft 3.5cm Thickness 1.8cm Plain steel, badly rusted, thread seized upNil

Heavy duty hex wheel wrench, losely tied to a piece of flat steel with several turns of steel wire (perhaps for strengthening). Handle Offset 22cm deep by 14cm wide. Flat steel base is warped and has three holes

Machinery PartSteel Coil Tension Spring 26cm long. 5cm diameter made with 6mm dia round steel. Around loop at each end in the same plane provides for hooking onto equipment

Teardop shape steel ring with end squared and bent at right angle for 6cm. Possible chainlink or attachment to plant machinery

Dates to the charcoal making period in the 1940sBlacksmith Tongs, 51cm long, jaws 8cm by 2cm. Diameter of handles 1.2cm. Handles badly bent and rusted.

perhaps used to rake out chacoal from kilnFormed Steel Rake or Scraper, a half-round steel plate rivetted to a short shaped steel arm. Rounded side of steel plate is ground to an edge

Heavy Duty Rake, with attachment to 2.5cm waterpipe fitting. 8 steel prongs are fitted with a flat steel scraper (50 x 8cm x 3mm) at the end, held in place with two steel clamps and two hex bolts and nut each

Heavy Steel Shackle made from 3cm round steel. 10cm internal depth and 3cm clearance. 3cm threaded bolt with square head. Short section of torn 1.5cm wire rope still attached

A 10cm round cylinder of wood on a 1.2cm round steel shaft, shaped into a 15 x 15cm crank handle. Both ends of the wood are banded with 2.5cm flat steel, fastened with bullet head nails

Ratchet Assembly on a flat surface cast bearing; one side broken off. 10cm dia ratchet wheel held in position by a locating pin. Captive handle 1.2cm round steel 35cm long. A 15cm piece of chain is attached to the shaft.

Stranger Stone (Concrete?) Column, cone shaped with hollow cavity in bottom7cmwide by 23cm deep. Two mounting holes in rim of base 2.5cm dia x 23cm deep. Undetermined use.

Small Trolley Axle with centre pivot, 32cm long, 4cm wide and 1cm thick. Axle bearings are formed 1.5cm diameter. Captive centre pin 14cm long, 1.5cm diameter.

20cm dia Cast Iron Trolley Wheel with 4 ribbed spokes. The rim of the wheel is slightly rounded. Axle hole is 2cm dia.

The Gas Producer is fitted with hinged mountings for attachment to the rear of a vehicle. Its central oval hopper is flanged by two round containers interconnected with 50mm tubing A faded brass nameplate identifies the unit as a Cheney - Pederick make

According to Les Solomano this unitoriginally belonged to the Hendricks brothers of Talbot. It was mounted on the front bumper of their 6 ton truck used for general cartage.The Unit shows the wide range of Gas Producers constructed during the war years to drive with charcoal fuel. This Gas Producer unit appears to be home-made mild steel construction for a specific purpose. The assembly sits on a welded frame, the hopoper on one side, the filter drum on the other and the radiator in between.there are no specific markings visible

Les Solomano tells us this unit was made by their cousin Frank Solomano and mounted on the passenger side running board of his A Model Ford, Spare bads of charcoal were tied to the rear door, so passengers had to get in and out through the driver side doors. It is the smallest Gas Producer unit we have seenThis Gas Producer unit is obviously a home made construction for a specific application. Absence of any air-cooling facilities suggests these may have been fitted separately inside the engine compartment.No specific marlings

This Unit was donated to us by the Falla Family of Donald, and picked up from the farm on 22 February 2007.The unit being in reasonable condition would almost lend itself to reconditioning for use.This Gas Producer Unit is in reasonable condition, with apparently all doors and fittings intact. The central oval shaped hopper is flanged by round and regular containers, interconnected with a series of pipes. Obviously a professionally made item, with signs of the original paintwork still visible. A brass nameplate states the make as Electrolux

In conversation with Mr Tibbett we found out that he obtained this particular unit at an auction in Sydney and brought it home with the intention of one day getting it going again. 'One day' never seemed to come, so he decided to let us have it for our display, rather than jjust collecting dust in his shed.This unit is again of a different manufacturer and construction, highlighting the versatile nature of charcoal producer gas and its applications. A commercially made cast iron unit with a solid round hopper/boiler on a steelframe base. It has a pressure-cooker lid and a car type radiator. Solid built, but rust affected in partsMake: Tysons Cross Draught Model: Official 30hp Heavy Duty Serial: 1368

Jack for changing wheels on light horse-drawn wagons. Contoured Lever Handle with holding Ratchet