Metal (silver-plated?) cylindrical base with a column rising up to a cylindrical storage area for kerosene. On top of this are three wires protruding out from the burner area. These wires would be used to hold the glass lens (not with the lamp)lamp, lantern, light, kerosene

Metal cylindrical base to store kerosene. Metal "arch" connected to the base and holding the top metal vent in place. The top vent and bottom vents have wire metal holding the glass lens in place. There is also a wire handle Lanora Australia, on baselamp, lantern, light, kerosene

Lamp made from metal/tin. Cylinder base to store the kerosene, with pump attachment to pump kerosene up to the lamp area. The lamp is attached to the base via a metal tube. the lamp is cylindrical with clear plastic lenses. On top of the lamp is a perforated metal cylinder for venting the fumes. on top of that is a metal circle for hanging the lamp. This is also a long screw which can be undone to access the lamp area. The whole lantern has a thick metal wire loop handle.lamp, lantern, kerosene, light

Metal cylindrical base to store kerosene. Above this area is a cylindrical glass area for the actual lamp light. Above this is a metal cylindrical cover with perforated holes for venting fumes. A thick metal wire handle is attached to the sides of the lamp. Access to the inside of glass area is via two spring-loaded clamps on either side of the glass area.On glass: Pyrex, Aladdin, Made in Australialamp, light, lantern, kerosene

The kerosene lantern is a type of lighting device that uses kerosene as a fuel. Kerosene lanterns have a wick or mantle as light source. They may be hand-held for portable lighting.This kerosene lantern was used as a light on road works in the Orbost area. It would have been carried/used by one of the road workers. Lamps of this kind were significantroadworks items in their period of use as essential tools to the safe-working operations of the Country Roads Board.. A red metal roadworks warning lantern. It is rectangular with a metal carrying handle. The top is domed. The door at the back is hingedand opens with a small nail. The lamp was lit by kerosene held in a small square tank with a wick.lantern kerosene light lamp

In the beginning of the19th century, the main mode of transportation was the horse and carriage. Even after the advent of the railway, remote areas still relied on the horse for local transport.Until Australian coachbuilders began making buggies from the 1860s, most were made in America Buggies with four wheels were light but comfortable. Many had hoods to keep the sun and rain off passengers. They were generally owned by doctors, ‘squatters’ and business people. Some had small turn-out seats at the back for children. Lamps are placed at different places on the carriage sides: 1 lamp on each side placed close to box seatThese lanterns are examples of lighting devices used in the time of horse and carriage transport.Two kerosene lanterns - buggy lamps.They are rectangular in shape and have a chimney on top. Both have carrying handles.There are 3 glass windows having two clear white lights and one small red round light on the back. The ceramic burner is made by Barton's.On ceramic wick holder - B in the middle of BARTONS B Underneath is TRADE MARK lighting kerosene-lights buggy-lamps transport lanterns

These lamps belonged to Ernie Eaton and were used for spotlighting rabbits. Carbide lamps, or acetylene gas lamps, are simple lamps that produce and burn acetylene (C2H2) which is created by the reaction of calcium carbide (CaC2) with water. Acetylene gas lamps were used to illuminate buildings, as lighthouse beacons, and as headlights on motor-cars and bicycles. Portable acetylene gas lamps, worn on the hat or carried by hand, were widely used in mining in the early twentieth century. They are still employed by cavers, hunters, and cataphiles Torches, candles, oil lamps and kerosene lamps were designed to be carried around but they could be dangerous because they have flame as a source of light. These lanterns are significant examples of lighting devices widely used used before the use of battery powered devices. A pair of Germania lamps. They have brass cases with steel bodied generators and convex lens. .1 is a metal carbide coach lamp. .2 is a similar lamp but has the chimney missing. .3 is a metal handle used to attach a lamp to the front of the vehicle.Germania Base has circle with three leaves.lantern lamp germania coach-lamp

http://en.wikipedia.org/wiki/File:Tilley-storm-lantern-X246-May- Tilley storm lantern, this model has been in production since 1964 The Tilley Lamp derives from John Tilley’s invention of the hydro-pneumatic blowpipe in 1813 in England. http://en.wikipedia.org/wiki/Kerosene_lamp#Pressure_lamp Pressure lamps are far more sophisticated than wick lamps and produce a much brighter light, although they can be quite complicated and fiddly to use. This type of lamp is commonly known in the UK as a "Tilley lamp", after a manufacturer of the same name, and in North America as a "Coleman lantern" for similar reasons. A kerosene blowtorch displaying the various aspects of the kerosene burnerA pressure lamp has a fuel tank at the bottom with a small pump to pressurise the kerosene. There is a narrow gap up to the top of the lamp, called a flue, and at the top of the lamp there is a burner (gas outlet). Directly underneath the burner is the mantle, a fabric bag coated with chemicals that incandesce when heated by the gas flame. The burner lamp is known for its brightness. It is so bright because of the amount of pressure that is placed onto the wick. This pressure allows a steady flow of the gasoline and a constant light Tilley Storm Pressure Lantern, model no x246 has a stainless steel base which is filled with kerosene, with a pump used to pressurize the kerosene vapor. Under the base is a sticker.On top is a black hood with vents which sits on the glass heat resistant shade. The glass shade has an etched label. It has a white and pink mantle on the central rod with a long shaped stainless steel handle, this folds down when not in use.Base - Sticker Tilley Lamp Model X246 Etched on glass shade Tilley, Durosil, ITI, Heat Resistant. Made in Englandlantern tilley pump pressure mantle kerosene methylated spirits stainless steel lamp kerosene lamp round glass cylinder

Bradley and Hubbard Co. 1869 to 1940. Pat'd 1895 - 1898.Used by a Kiewa Valley residentNickel plate body with glass chimney and large white lamp shade. Both bowl and base are panelled and the base is scrolled on the edge. The bowl has a fill cap inscribed B & H and opposite there is a ratchet wheel lift. On top of the bowl is a decorated cylinder which lifts up to enable the lamp to be lit with a match. The glass chimney sits on top. There are 3 curved equally spaced rods coming up around this cylinder - to hold up the shade.Embossed on Fill Cap lid: "B & H" Embossed on top of bowl "Dec. 1885 / No. 4 Radiant / The/ B & H" and opposite "Pat'd Aug. 16 1888" Embossed on side under the 'grate': Pat'd Feb. 16 '97" Painted on glass chimney: "Griffen - Brand / dragon logo / Fire Proof / Madein Saxony / Rochester / No. 2lamp, lantern, bradley & hubbard, kerosene, oil light

The period when kerosene was extensively used for indoor lighting was before electrical reticulation was installed in rural areas. In remote areas this was up to the mid 1900's. The kerosene lantern however was still in use, for camping and outdoor activities, well beyond this period and was eventually replaced by LPG and battery powered lighting. The transition phase to "modern" outdoor and domestic lighting lingered on the rural areas where the electrical reticulation suffered from reliable constant supply.In the Kiewa Valley, being a rural region, had reliable electrical domestic and farm supply only after the Kiewa Hydro Electricity Scheme had been fully operational. The supply was relative to how close the homestead was to the major electricity substation. This kerosene lamp was in use during the period when it was the only reliable source of domestic night time lighting. The strength of refractive light produced by this lantern/lamp hinged upon the size of the lamp(wick and glass bowl). The small size of this lamp suggests that it was for use in a small room(children's bedroom) or as providing a light for a safe walk to the outside ablutions (toilet) area. This small kerosene lamp has an enclosed "cup" body which would have contained the kerosene fuel. The top wick holder, made from brass, has an extended enclosed spout which raises the wick approximately 20mm from the bottom of the holder. The wick holder screws into the the top of the kerosene reservoir bowl and has a wick adjustment screw (light control) at one side. The small white glass light reflector bulb nestles securely onto the wick holder and is kept snug by snap designed extending "fingers". The section between the bottom of the refractive glass "light" bowl and the top of the kerosene bowl has perforations to allow air passage to feed directly to the wick.The light refracting bulb is open at the top to allow heat and smoke from the burning wick to escape upwards.On the wick control screw "CWB BRITISH MADE"kerosene reading lamp, domestic lighting, bedside light

This item is an important example of the early technology of artificial light. It has historical significance in demonstrating lighting devices used before the widespread use of electricity.Kerosene/oil hand-held lantern with carry handle. Red glass window (for a show of red light) and a clear glass window that opens for lighting of wick. (Dietz Dainty Tail Lamp)lantern candle dietz-dainty-tail-lamp

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. This lamp appears to be a modern reproduction of an earlier optional wall-mounted kerosene lamp. The lamp has been produced as an example of a 19th and early 20th-century marine kerosene navigation lamp. Marine lamp; portside metal kerosene lamp with two flat sides, and a curved front. The front has a red ridged glass lens insert and the name "port" is inscribed on a fixed brass plaque. A round chimney is on top of the lid and it has a catch. The fuel tank and wick can be removed through the base. The metal appears to be electroplated.Inscribed on the plaque; "PORT"warrnambool, shipwreck coast, flagstaff hill, flagstaff hill maritime museum, flagstaff hill maritime village, lamp, ship lamp, port lamp, marine lamp, navigation lamp, port, lantern, kerosene lamp, marine technology, ship light, portable lamp

The subject item was produced in 1914/15 by the Telford Grier and Mackay Company in Glasgow, Scotland, this lantern was not used to provide visibility for Sailors on a ship, rather, it is meant to help other vessels identify the ship’s presence and heading in low visibility conditions hence it is marked Port and has a red filter. The lantern would have been placed along the port side of larger vessels to provided an unbroken light and would be visible in an arc from as well as at an angle from the port side of the vessel. The company was established in 1904 at 11 Fairley Street Glasgow and in 1922 moved to 10 Carrick Street. The company manufactured patented lamps for marine use, later moving into the manufacture of electrical and mechanical items. A significant marine kerosene lantern made by a company that patented this type of lantern for use by the British Navy and for merchant ships the world over. This item today is rare and sought by collectors.Ship's port side sidelight lamp with clear glass frenal lens with red filter behind, burner missing, replacement with modern electric fittingTwo makers lozenges one marked PORT the other has the maker Telford, Grier and Mackay, Glasgow, 1915 marked on main body chimney has 1914 marked . Also serial No C976 stamped on backplate.flagstaff hill, warrnambool, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, lamp ship's sidelight, ship's sidelight lamp, port lamp, marine light, navigation light, kerosene ship lamp

The kerosene lamp was one of the most common oil lamps used and was manufactured until the 1980s. An anchor lamp like the lamps in this pair would be raised on the highest ship mast at night to signal other seafarers that the ship was at anchor or sailing at night. The metal loops on opposing sides of the lamp could hold a pair of rods or ropes. and be used to raise the lamp.The lamp is made to the design of a 19th and early 20th-century kerosene anchor lamp carried as essential marine equipment and used as a signal lamp on sailing ships. Lamps; a pair of cylindrical kerosene anchor lamps. Each has a flat back, a hinged door, a metal handle and two metal loops or guides fixed on each side. The glass window is convex and inside the lamp is a wick in an enamel wick holder.brass lamp, lamp, anchor kerosene lamp, kerosene lamp, marine equipment, marine lamp, navigation, light, ship light, ship lamp, lantern, maritime, nautical, safety lamp

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The screws on the side adjust the flame and hence the strength of the flame produced. Prior to the introduction of gas and electricity these lamps provided lighting in all householdsPioneers and early settlers in Moorabbin Shire relied on kerosene lamps for lighting their homes after sunset.This kerosene, flat wick, banquet lamp has a clear glass shade chimney with a frilled rim, a reservoir of plain yellow glass and a metal engraved base . 1 side screw to adjust the flamelights, early settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, cheltenham. lamps, kerosene, paraffin, oil

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The side screws adjust the length of the wick and hence the strength of the flame / light produced. Prior to the introduction of gas and electricity these lamps provided light in households after sunset.Prior to the introduction of gas and electricity these lamps provided light after sunset for the early settlers, as they established their farms and businesses, in Moorabbin Shire.A Victorian kerosene banquet lamp, with a gilded metal quad footed base, cranberry glass oil reservoir with geometric patterns, original etched, yellow, glass globe shade and clear glass chimney. There are 2 side screws for adjusting the flame.early settlers. pioneers, follett w, moorabbin, bentleigh, brighton, ormond, market gardeners, kerosene, paraffin, lights, lamps, candles

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The side screws adjust the length of the wick and hence the strength of the flame/light produced. Prior to the introduction of gas and electricity these lamps were used for lighting in all households after sunsetPioneers and early settlers relied on kerosene lamps for lighting their homes after sunset.A 19th Century kerosene chamber lamp, with clear, plain glass shade and reservoir, circular metal base and 1 side screw for adjusting the flameearly settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, ormond, cheltenham, candles, lights, lamps, kerosene, paraffin, oil

Prior to the launch of the motor powered Queenscliffe, three row boats were in service as lifeboats. This lantern was part of the equipment of the third lifeboat up to 1926.A brass lamp which was part of the safety equipment on board the Third Queenscliff LifeboatBrass Lantern with interchangeable port and starboard glass filters run of kerosene.Brandt Bros Melbourne Manufacturers 422 Elizabeth Streetlight, navigational safety

The heavy twin tanks formerly contained vaporised kerosene which was used as a fuel to light the lantern. Kerosene became available in the 1860s as the oil industry in the United States developed, and vaporised kerosene soon became the most common system of illumination. The kerosene vapour lamp was perfected by Chance Bros. for burning the light in their renowned lenses. The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. Kerosene tanks like these were developed in the early twentieth century, and kerosene as a fuel was phased out by electricity, with the last kerosene system in Australia eventually replaced in 1985. The wick lamp in Gabo Island’s light was altered to a vaporised incandescent kerosene mantle burner in 1909. They would have been in use until 1935, when the light was electrified and the original first-order lens was replaced by a fourth-order lens. The Gabo Island tanks, which are presumed to be those used in the lighthouse between 1909 and 1935, are not attached to the optical apparatus and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. Cape Schanck has a pair of unattached tanks, which are not historically associated with the lighthouse. Point Hicks has an iron stand that formerly supported its lighthouse oil tanks. Despite their lack of intactness, the Gabo Island tanks have first level contributory significance for their provenance to the lightstation and historic association with the lantern’s original Chance Brothers first order lens, which was removed in 1935Two large green cylinders standing in a metal frame. There is also a pumping mechanism attached to the stand with a wooden handle.

A small number of heavy cast iron weights and two rods remain at the Point Hicks Lightstation. These weights comprise one rod with a forked top and four circular weights attached to the bottom of the shaft. The weights and rods were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. They were attached to a cable or chains and moved vertically in similar fashion to the way weights move on grandfather clocks. As the weight fell, the optic clock was driven and the lens was turned. To keep the clock turning, the weight needed to be wound back up to the top of its travel. The cables and weights in this lighthouse were visible as they moved through the length of the tower up to the lantern room. It was usual for systems to move inside a tube extending up to the top, but in this case the tower’s cast iron spiral staircase, which is supported on cantilever cast iron brackets set into the concrete wall, spiralled around the space in which they moved. Lighthouse keepers had the arduous job of having to constantly wind the clock to keep the light active, and at least two keepers needed to observe a strict roster of hours. When electric motors were invented, all of this became redundant and the motors were able to turn the optic for as long as there was power to drive them. In December 1964, the original 1890 Chance Bros kerosene‐fuelled light and clockwork mechanism were replaced by small electric motor, and the number of keepers reduced to two. The six circular weights and rods originate from the obsolete system and may have been part of a larger set. Wilsons Promontory retains seven of its original set of ten weights, all of which are detached from the tower’s weight tube. Cape Schanck has a set of fourteen weights remaining in situ as well as another four detached weights, which have inscriptions. One weight is displayed in the lantern room at Cape Otway. The image shows four of the clockwork weights attached to a rod with a forked top. They were part of the original clockwork mechanism that was fitted beneath the lens to keep the kerosene‐fuelled light turning. The Aldis lamp in its case sits on the floor next to the weights. Source: Parks Victoria.The Point Hicks weights have first level contributory significance for the insights they provide into the superseded technology and operations of a late nineteenth century lighthouse. They are well provenanced and are significant for their historic value as part of the lightstation’s Chance Brothers optical system installed in 1890. Four circular metal weights are stored on a metal rod with a forked section at the top. The weights have a cut out section which allows the weights to be removed easily.

The two hand-held, portable kerosene lamps each have green enamel caps over the glass. They were used from around the 1930s until 1993, and one is now located on the groundfloor level of the lighthouse and the other is in the assistant lightkeeper’s quarters. The brand name of the Point Hicks lamp, while not stated is probably Coleman, Tilley or Austramax, which were all similarly made, portable pressurised kerosene lamps. Coleman brand pressure lamps and lanterns were first made in about 1905 by American, William Coleman, and their English competitor was the firm, Tilley. The Australian company Austramax began manufacturing kerosene pressure lamps in Brunswick in 1946, making the bases and the workings by hand, turning out 1000s of lamps each week. Portable lamps were used worldwide where bright light was needed and they became essential as an emergency back-up source of light for the lightstation as well as the lantern room. Through the multiplication of light by the lighthouse lenses, they could provide a tower with a 26 nautical mile range. Lamps similar to the two Point Hicks examples can be found at Gabo Island, one of which is a green enamelled Austramax lamp; Cape Nelson (Austramax), and similar lamps are held at Cape Schanck and Cape Otway. The two Point Hicks lamps have first level contributory significance for their historic value and provenance, and as representative examples of lamps that were widely used in Australian lightstations between the 1930s and 1960s.PHLS0008.1 & PHLS0008.2 Pressurised kerosene lamp, cover over glass is made of green enamelled metal.

Was the stand for a Chance Brothers air & oil containers fitted with pump handle & pressure gauges.This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness. The oil was fed under pressure to the burner mantle. It is all that remains of an air and kerosene oil tank installation, with each rounded side formerly supporting a heavy iron tank. The containers would have been fitted with a pump handle and pressure gauges. An intact assemblage is displayed in the AMSA offices, Canberra with a text that explains ‘This type of installation was once common and relied on the lightkeeper having to pressurise the cylinders manually at regular intervals throughout the hours of darkness’.The system involved vaporising kerosene under pressure and mixing it with air and then burning the vapour to heat an incandescent mantle. The use of kerosene as a fuel to light the lantern became the most common system of illumination from the 1860s after the oil industry in the United States began to develop. The kerosene vapour burner was created in 1901 by British inventor Arthur Kitson (1859-1937) and perfected by Chance Bros for burning a more intense light in their renowned lenses. The lamp had to be watched throughout the night in case a mantle broke, and the tanks needed to be maintained by hand-pumping each hour or so. The Point Hicks lantern was initially lit by a six-wick Trinity house kerosene burner. This was replaced by the more efficient and brighter 55mm vaporised kerosene mantle burner in 1905, and the tank stand is probably original to this apparatus. Electricity eventually replaced kerosene at Point Hicks in 1964 making the tank installation obsolete, and the last kerosene system in an Australian lighthouse was replaced in 1985. Gabo Island Lightstation has a pair of tanks that are not attached to the optical system and are no longer in the lighthouse. They are also missing the pressure gauges that were formerly attached to the top of each cylinder. An intact tank assemblage is displayed at the Cape Schanck Lighthouse Museum it is detached and not original to the lighthouse. Although corroded, the remnant Point Hicks tank stand has first level contributory importance to the lightstation. It is significant for its provenance and historical value as part of the Chance Bros vaporised kerosene burner introduced in 1905 to intensify the light and improve the efficiency of the system. The rusted iron stand rests on four short legs and is shaped like a pair of spectacles.

These lamps would have been used in the late 19th and early 20th centuries for outdoor, industrial, or domestic lighting, before the widespread availability of electric lighting. The left lamp is a traditional lantern, likely used for portable lighting, either carried by hand or hung on a hook. It could have been used on farms, in railway stations, or in military settings. The right lamp is an oil or kerosene lamp, possibly wall-mounted and used in stables, workshops, or early automobile garages. The reflector helped to direct light forward, making it more efficient in dimly lit spaces. Both lamps have significant wear and damage, indicating long-term use and exposure to the elements.The image shows two old metal and glass lamps, both exhibiting signs of heavy wear and damage. Left Lamp: A rectangular lantern-style lamp with a metal frame and glass panels on all four sides. The glass is cracked and broken, with missing sections, and the metal frame is corroded and bent. A metal loop handle at the top suggests it was meant to be carried or hung. The interior appears hollow, where a candle or oil lamp would have been placed for illumination. The metal has a dull silver-grey finish, likely due to oxidation. Right Lamp: A cylindrical oil lamp with a flat back and a hinged metal reflector at the top. The base contains a round opening, likely where the wick holder and burner were originally inserted. The metal body is painted or enamelled, but the finish is chipped and worn. The top reflector is bent and dented, but the hinge remains attached. The flat back suggests it was a wall-mounted lamp, possibly used in barns, workshops, or railway applications.lamps, kerosene, lamp, candle, light

Kerosene lanterns like these were commonly used from the mid-19th century to the early 20th century before electric lighting became widespread. Railway & Signal Use – Some lanterns, particularly those with enclosed rear casings, may have been used as railway signal lamps. Camping & Outdoor Use – The smaller, lightweight designs were portable, making them useful for camping, farming, and night-time travel. Household & Industrial Lighting – Before electrical grids, kerosene lanterns were used for home lighting, barns, and industrial workspaces.This collection consists of several rusted kerosene lanterns, showing various designs that were common in the 19th and early 20th centuries. Key features include: Metal body construction, likely iron or steel, with a cylindrical glass globe in most of the lanterns. Protective wire guards, designed to shield the glass globe from breakage. Carrying handles and hanging hooks, allowing them to be portable or mounted. Some lanterns feature side reflectors or enclosed rear casings, suggesting they may have been used as railway or signal lamps. Different shapes and sizes, some with rounded oil reservoirs, while others have flat-bottomed bases for stability. The lanterns show significant wear, with rust and corrosion evident on the metal parts, and some globes showing dirt, soot, or residue from past use.lantern, light, lamp, household item