A flat-wick lamp is a simple type of kerosene lamp, which burns kerosene drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat," or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light which is brighter than that produced by an open flame. The lamp burner has a flat wick, usually made of cotton. The lower part of the wick dips into the fount and absorbs the kerosene; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick, and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a toothed, metal sprocket bearing against the wick. A paraffin lamp with a green metal base to hold fuel with a side screw to adjust wick length. An opaque white glass shield sits in a metal frame attached to base* moorabbin, bentleigh, cheltenham, pioneers, early settlers, market gardeners, lights, lamps, paraffin, oil lamps

Paraffin lamp. Dark wooden turned ornate stem. Metal base. Vitreous enamel fuel reservoir. Glass chimney with mantel. Plastic and cloth shade."Aladdin 21C Made in England GB. PAT. NOS. 694273-4 21C11" imprinted on fuel reservoir. "Aladdin heat resistant glass" imprinted on chimney. " Remove this gallery when lighting REG. TM. Aladdin Made in England" Written on gallery (under chimney)lighting, kerosene & oil, aladdin, kitchen lamp, light, paraffin, mantel, table lamp, chimney, lamp shade.

Paraffin lamp with clear glass oil reservoir and stand. Oil reservoir is spherical in shape and has a bird pattern embossed while stand has a fluted base with decorative rivets and turns. On top of oil reservoir is a brass wick holder. It seems to be missing the chimney."An Qing China" is imprinted on interior of base along with an "A" in a circle. Chinese characters/letters are also imprinted on base interior and can be translated to the same as the English.lighting, kerosene & oil, light, lamp, paraffin, oil, birds, glass.

This is a typical example of a flat wick domestic paraffin lamp used in households prior to the introduction of electricity.A flat-wick lamp is a simple type of paraffin lamp, which burns paraffin drawn up through a wick by capillary action. A flat-wick lamp has a fuel tank (fount), with the lamp burner attached. Attached to the fuel tank, four prongs hold the glass chimney, which acts to prevent the flame from being blown out and enhances a thermally induced draft. The glass chimney needs a "throat", or slight constriction, to create the proper draft for complete combustion of the fuel; the draft carries more air (oxygen) past the flame, helping to produce a smokeless light, which is brighter than an open flame would produce. The wick holder has holes around the outer edges. When the lantern is lit and a chimney is attached, the thermally induced draft draws air through these holes and passes over the top of the wick. This has a cooling effect and keeps the wick from over heating. The lamp burner has a flat wick, made of cotton. The lower part of the wick dips into the fount and absorbs the paraffin; the top part of the wick extends out of the wick tube of the lamp burner, which includes a wick-adjustment mechanism. Adjusting how much of the wick extends above the wick tube controls the flame. The wick tube surrounds the wick and ensures that the correct amount of air reaches the lamp burner. Adjustment is usually done by means of a small knob operating a cric, which is a toothed metal sprocket bearing against the wick. If the wick is too high, and extends beyond the burner cone at the top of the wick tube, the lamp will produce smoke and soot (unburned carbon). When the lamp is lit, the paraffin that the wick has absorbed burns and produces a clear, bright, yellow flame. As the paraffin burns, capillary action in the wick draws more kerosene up from the fuel tank. All paraffin flat-wick lamps use the dead-flame burner design, where the flame is fed cold air from below, and hot air exits above. (Source: Wikipedia accessed 24 Nov 2023) This lantern has a circular heavy green glass base for holding the paraffin. The base has a 12mm green glass handle. There is a small clear glass chimney with a fluted upper edge and some bubbles in the glass. The metal burner and wick holder has four metal prongs to hold the glass chimney in place. The round metal wick winder is functioning. There is a small amount of residual paraffin in the base. The flat wick is made of cotton.There are no markings to indicate the manufacturer.paraffin lamp, flat wick lamp, domestic lantern

Steel framed paraffin lamp with steel base. Glass bulbous chimney with embossed writing and makers mark. Thin steel wire for protecting glass, and as handle on top with hook indent, attached to frame. Mechanism for raising and lowering glass casing by small handle attached to frame for facilitating lighting. Wick trimming device on side of base, and cap covering hole in base for filling.On glass - 'Feuerhand, Made in Germany' embossed. On opposite side, company logo of hand holding flames. On base - 'Made in Germany', embossed. Company logo. '*Nr. 327' Company logo on oil cap, wick trimming knob and on top of framelighting, kerosene and oil, hurricane, lamp, paraffin, feuerhand, lighting. dora buckley

Clear glass fuel reservoir with radial ribbed design and handle. Glass chimney."Victor" embossed on gallery.lighting, domestic, glass, lamp, lighting.

Table lamp with tubular wick, paraffin. Cast brass decorative base with four feet, cast brass interior and burner, with glass exterior and covering. Pink and white base colours on glass, with floral pattern printed on both sides of lamp. Cover a semi-circular shape with round neck opening on top.… Success…' (some words unreadable) embossed on burner platelighting, kerosene & oil, table lamp, brass, glass, paraffin, floral

Irons such as this were very popular prior to the widespread introduction of electricity in Australia. It was manufactured by the Tilley Lamp Company Ltd. In 1818 John and William Henry Tilley established W. H. Tilley, in Stoke Newington, London, England. During WW1 they started to use paraffin as a lamp fuel in pressurised containers. A production plant was established at Hendon, just north of London, and the first commercial lamps were produced after World War 1. During the 1920s the company diversified into domestic lamps. This expanded to other appliances such as heaters and eventually to irons. The use of paraffin or kerosene as a fuel was a much cleaner form of heat, especially when compared to older flat irons which used coal.This item is significant because it is representative of domestic appliances used in the Wodonga District prior to the introduction of electricity throughout the area.Cream coloured iron with a black Bakelite handle which attaches to the fuel tank. It has a steel sole plate. The heat of the iron is provided by a paraffin burner.On Metal plate: Model D.N. 250 Made in England British Pat. 524719 Australian Pat. 114305 On Knob at rear: ON/OFF TILLEYdomestic appliances, tilley paraffin iron, tilley lamp company ltd.

CAME FROM THE CAMPBELL FARM, FRAMLINGHAM, VICTORIA, AUSTRALIAMETAL DRIVING LAMP, PARAFFIN WICK, CLEAR FRONT LIGHT & RED REAR LIGHTDIETZ UNION local history, dietz usa, driving lamp

This is a vintage lighting mechanism probably dating from the 1920s. It would have been used in a household or business to provide lighting for a room. It is quite heavy so would have mostly rested on a table or ledge. It is a Petromax lantern, a brand name for a type of pressurised paraffin lamp that uses a mantle. The Petromax lantern was developed in 1910 by Max Graetz of the firm of Ehrich and Graetz of Berlin, Germany (petro= petroleum, max=Max Graetz).The Petromax lantern is still produced todayThis lantern is of antiquarian interest as an example of household lighting100 years ago.This is a lantern with a metal base, a wooden stem painted black, a metal body holding a piece of circular glass and a metal top with perforations acting as a chimney. The base has a hand pump and a removable screw cap to enable the base to be filled with paraffin. The main body has a screw holder to control the lighting and a pre-lighting mechanism and a mantle fitting inside the glass. The mantle is missing.PETROMAX No. 886 MADE IN GERMANYvintage lighting, petromax lanterns

Tilley lamps, famously known for their bright white light and reliance on kerosene pressure, originated from John Tilley’s 1813 invention of the hydro-pneumatic blowpipe. Developed as a portable paraffin (kerosene) lamp in 1915, the Tilley Lamp Company became iconic for durable lighting in the railways, military, and households before moving to Northern Ireland in the 1960s. They were used in homes and outdoors.Four vintage Tilley Lamp Vapourisers ( three new and one sealed in a plastic wrap). 1. Tilley Vapouriser Part No. 606. in a red and yellow long rectangular cardboard box complete with a cleaning wire part. 2.Tilley Vapouriser Part No.No. 606. in a red, black and white long rectangular cardboard box, complete with a cleaning wire part. 3. Tilley Vapouriser Part No.169. in a black and yellow long rectangular cardboard box, complete with a cleaning wire part. They all have patent numbers. 4. One loose vapouriser encased in plastic without a box.Each box has full details of parts and manufacturing.lighting equipment, lights, lamps, kerosene lamps

Tilley lamps, famously known for their bright white light and reliance on kerosene pressure, originated from John Tilley’s 1813 invention of the hydro-pneumatic blowpipe. Developed as a portable paraffin (kerosene) lamp in 1915, the Tilley Lamp Company became iconic for durable lighting in the railways, military, and households before moving to Northern Ireland in the 1960s. The 1940's and 50's were the golden age of matchbook art, where the covers acted as miniature canvases for marketing, often featuring art deco or commercial designs.A small red cardboard matchbook style Set of Washers No 498 for Tilley Lamps and Radiators. There are five types of washers sealed in a cellophane bag stapled to the base of the folder. Inside the foldout section are instructions for use of the washers, with illustrations. On the back of the folder is a black and white outline of a stylised owl next to the text, Tilley Lamps, I always use them, and a lamp. 'Set of Washers No 498 for Tilley Lamps and Radiators' There is a black and white outline of an owl with the moon behind it. Inside the foldout section are instructions for use of the washers, with illustrations. On the back of the folder is a black and white outline of a stylised owl next to Tilley Lamps, 'I always use them!' 'KCR TYPE 2287' is printed at the top of the card.lighting equipment, lamps, kerosene lamps

1. State Express Ready Rubbed, produced by the Ardath Tobacco Company (est. 1895 London), was a popular Virginia tobacco, notably manufactured in Australia during the mid-20th century. The tins were typically small to mid-sized, featuring the "State Express" and "Ardath Fine Cut" branding, with "Ready Rubbed" indicating it was pre-shredded tobacco. Used widely by Australian soldiers in WWII, these compact tins are highly collectible today, appearing through the 1960s. 2. The Tilley Storm Lantern,company started in the early 19th century, with William Henry Tilley manufacturing gas lamps in the 1830s. By 1919, the company pivoted to kerosene (paraffin) pressure lamps, using a pressurized system for lighting, which was improved with incandescent mantles. The company expanded rapidly, securing major contracts to supply lamps to railway companies for track work and inspections. Tilley lamps were extensively used by British armed forces during both World Wars. In WWII, they were essential for field operations, guiding aircraft (RAF), and providing light in blackout conditions. 1. A red rectangular, State Express cigarette tin with a hinged lid. The company logo and other details are printed in gold lettering on the lid as well as Ready Rubbed Virginia Tobacco Ardath Fine Cut. There is an insignia with two crossed heraldic flags and an eagle on top. This information is printed in black lettering on a gold background inside the lid. 2. The tin contains a folded green paper instruction leaflet for the use of a Tilley Storm Lantern made in England with a black plastic branded Tilley Spare Part Dipstick used for measuring the fuel level. There is also a broken thin black ring fitting.1. On the front of the lid: 'State Express Ready Rubbed Absolutely unique in its quality Virginia Tobacco Ardath Fine Cut'. There is an insignia with two crossed heraldic flags and an eagle on top. 2oz. Net Weight. When packed is at the bottom in black print. Inside the lid: 'Every tin of genuine Star Express Ready Rubbed Ardath Fine Cut has the name of Ardath printed on the paper lining' The insignia is also printed. 2. Included is a green folded pamphlet 'Hints on the use of your Tilley Storm Lantern (Regd.)' Information in the leaflet is quite detailed. The dipstick has 'The Tilley Lamp Co. Ltd. Dipstick for Models named on reverse. E.X.100.,P.L.53.,10.,T.L.13., R. T.L.106.,T.L.136.,X246.K.L.80.,LIFE BUOY. USE ONLY GENUINE 'TILLEY' SPARE PARTS'smoking equipment, cigarette containers, tobacco

NSWTD Railway Marker OIl lamp, No.1 RA Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil Lamp NSWTD Railway Marker lamp, No.1 RA made of metal and Glass Railway lamp, paraffin, metal/glass/fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870 - 1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTD 1 RApuffing billy railway , pbr, nswtd railway marker oil lamp, no.1 ra

Four NSWTD Railway marker Oil lamps at Nobelius Packing shed Item stamped numbers unknown Oil burning lamps have always been an important part of Australian railway signalling systems and have been used for communication, safety and lighting. It is called a marker lamp and was hung on rolling stock (carriages and wagons) such as the guard’s van to indicate the rear of the train at night. They were also used to indicate the rear of steam locomotive tenders for identification and safety purposes. This type of lamp was introduced to the railways around 1860 and continued to be used for over one hundred years. Oil lamps were phased out on the railways during the late 1960s and early 1970s, when they were replaced by battery lamps. Railway lighting included not only stations but yards, engines, rolling stock, signals, signal-boxes and crossings. There were a number of different types of lamps used for a variety of railway purposes. Historic - New South Wales Transport Department.- Railway Marker Oil LampFour NSWTD Railway marker Oil lamps made of metal and glass Railway lamp, paraffin, metal / glass / fabric, used for attaching to railway rolling stock to mark the end of the train, made by the New South Wales Transport Department, Sydney, New South Wales, Australia, 1870-1970 This lamp comprises a hollow cube of metal. One lens at the front transmits light from an interior light source. Fuel was either signal oil or kerosene. The burner inside the lamp used either cotton or felt wicks to create the light source. The lamp has a carry handle for carrying by hand and a bracket with a slot on the back for hanging onto the hook of a locomotive or item of rolling stock. It is marked "NSWTD" which stands for New South Wales Transport Department.NSWTDpuffing billy railway , pbr, four nswtd railway marker oil lamps

This magic lantern or slide projector was used to project glass slides on to a screen The magic lantern was the chief visual entertainment for the public before the introduction of the moving picture and consequent cinema entertainment. This one probably dates from about 1915 but its provenance is not known.This magic lantern is an important and interesting object as it shows us the way people in the early 20th century were entertained. The few people who owned this type of projector would give public showings of slides of people and scenes and sometimes raise money for a charitable cause in this way. This is a glass slide projector or magic lantern with a rectangular metal lantern body partly open at the back. The back has a top section that is attached with a metal hinge and lifts up and outwards. The lantern base also has a side opening with a metal knob for opening and a metal panel with a blue glass inset. Inside the lantern body is the lamp and an electric cord (the illuminant system may have originally been fuelled by paraffin or another oil burner). On top of the lantern body is a smaller rectangular metal box in two sections. This can be removed. The illuminant system is brass and slides out. It has two mechanisms for adjusting the focus and a covering over the lens opening which can be pulled up. There is also a wooden slide holder which can be pulled in and out of the projector. ‘W.B. British Made’ social history, history of warrnambool, glass slide projector

This slush lamp was used in the Newmerella Bakehouse ( Sederlan's Bakery) before electricity was connected. In the days before battery powered torches many used a slush lamp to provide the light they needed to carry out their duties. It held a flammable liquid like paraffin. When the wick was lit the slush lamp provided sufficient lightSlush lamps were designed to be carried around but they could be dangerous because they have flame as a source of light. This is an example of a portable lighting device in common usage before the use of batteries.A cast iron slush lamp. It is a a crude lamp or burning slush, tallow, or grease.It is a jug shaped container on a shallow dish that holds the fuel and a wick that draws the fuel by capillary action. There is some burnt hessian impregnated with fat. lighting lamp-slush newmerella-bakehouse

In the days before battery powered torches many used a slush lamp to provide the light they needed to carry out their duties. It held a flammable liquid like paraffin. When the wick was lit the slush lamp provided sufficient light.Slush lamps were designed to be carried around but they could be dangerous because they have flame as a source of light. This is an example of a portable lighting device in common usage before the use of batteries.A black metal slush lamp with two glass panels and a stock. At the back is a hinged door. There is a hole on top caused by rust or being burned through. Kerosene or oil was probably the fuel used.On top of light - Serial No 339220slush-lamp lighting kerosene oil

The Tilley lamp & heaters derives from John Tilley’s invention of the hydro-pneumatic blowpipe in 1813 in England. W. H. Tilley were manufacturing pressure lamps at their works in Stoke Newington in 1818, and Shoreditch, in the 1830s. The company moved to Brent Street in Hendon in 1915 during World War I, and started to work with paraffin (kerosene) as a fuel for the lamps. During World War I Tilley lamps were used by the British armed forces, and became so popular that Tilley became used as a generic name for a kerosene lamp in many parts of the world, in much the same way as Hoover is used for vacuum cleaners. During the 1920s the company had diversified into domestic lamps, and had expanded rapidly after orders from railway companies. After World War II fears about the poisonous effect of paraffin fumes, and widely available electricity, reduced demand for domestic use. The company moved from Hendon to Ireland in the early 1960s, finally settling in Belfast. It moved back to England in 2000.Item is significant as it was an early form of portable heating used in a domestic situation or any small room that required to be heated. This item fell out of use when electricity and electric heater became more available and affordable. Tilley kerosene pressure heater with large reflector dish. Fuel tank painted cream and wooden handle.Tilleyflagstaff hill, warrnambool, flagstaff-hill-maritime-museum, maritime-museum, shipwreck-coast, flagstaff-hill-maritime-village, kerosene heater, tilley lamps, john tilley, pressure heater, domestic use

The Tilley lamp derives from John Tilley’s invention of the hydro-pneumatic blowpipe in 1813 in England. W. H. Tilley were manufacturing pressure lamps at their works in Stoke Newington in 1818, and Shoreditch, in the 1830s. The company moved to Brent Street in Hendon in 1915 during World War I, and started to work with paraffin (kerosene) as a fuel for the lamps. During World War I Tilley lamps were used by the British armed forces, and became so popular that Tilley became used as a generic name for a kerosene lamp in many parts of the world, in much the same way as Hoover is used for vacuum cleaners. During the 1920s the company had diversified into domestic lamps, and had expanded rapidly after orders from railway companies. After World War II fears about the poisonous effect of paraffin fumes, and widely available electricity, reduced demand for domestic use. The company moved from Hendon to Ireland in the early 1960s, finally settling in Belfast. The company moved back to England in 2000.A significant item demonstrating the early use of kerosene under pressure as a lighting medium. These types of lamps were made by a company whose products became synonymous with oil lamps generally. Lamps that were used commercially, domestically and by the armed forces of many countries during the first and second world wars.Tilley Searchlight Projector, or search lamp, made in Hendon, England 1935. Metal kerosene pressure search lamp, glass front, fixed mirror at back, wooden carry handles. Mounted on fuel tank with pressure pump. Lamp has 8 airflow holes in the bottom and a covered outlet on the top. Glass is in 3 pieces, fitting together to make flat circle there is a maker’s plate on the pressure tank. “TILLEY / SEARCHLIGHT PROJECTOR / MADE AT / HENDON, ENGLAND”, “256” handwritten in red on one wooden handle, “9” or “6” hand painted in white on top on lightflagstaff hill, warrnambool, flagstaff hill maritime museum, maritime museum, shipwreck coast, flagstaff hill maritime village, great ocean road, tilley kerosene pressure searchlight, lighting, john tilley, pressure lamps

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The screws on the side adjust the flame and hence the strength of the flame produced. Prior to the introduction of gas and electricity these lamps provided lighting in all householdsPioneers and early settlers in Moorabbin Shire relied on kerosene lamps for lighting their homes after sunset.This kerosene, flat wick, banquet lamp has a clear glass shade chimney with a frilled rim, a reservoir of plain yellow glass and a metal engraved base . 1 side screw to adjust the flamelights, early settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, cheltenham. lamps, kerosene, paraffin, oil

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The side screws adjust the length of the wick and hence the strength of the flame / light produced. Prior to the introduction of gas and electricity these lamps provided light in households after sunset.Prior to the introduction of gas and electricity these lamps provided light after sunset for the early settlers, as they established their farms and businesses, in Moorabbin Shire.A Victorian kerosene banquet lamp, with a gilded metal quad footed base, cranberry glass oil reservoir with geometric patterns, original etched, yellow, glass globe shade and clear glass chimney. There are 2 side screws for adjusting the flame.early settlers. pioneers, follett w, moorabbin, bentleigh, brighton, ormond, market gardeners, kerosene, paraffin, lights, lamps, candles

The kerosene lamp is a type of lighting device that uses kerosene as a fuel. Kerosene lamps have a wick or mantle as light source, protected by a glass chimney or globe; lamps may be used on a table, or hand-held lanterns may used for portable lighting. There are three types of kerosene lamp: traditional flat wick, central draught (tubular round wick), and mantle lamp. The side screws adjust the length of the wick and hence the strength of the flame/light produced. Prior to the introduction of gas and electricity these lamps were used for lighting in all households after sunsetPioneers and early settlers relied on kerosene lamps for lighting their homes after sunset.A 19th Century kerosene chamber lamp, with clear, plain glass shade and reservoir, circular metal base and 1 side screw for adjusting the flameearly settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, ormond, cheltenham, candles, lights, lamps, kerosene, paraffin, oil

Early Settlers used candles and lamps as their source of light after sunset. This lamp, uses a flat wick immersed in kerosene or oil, contained in the bulbous reservoir, with a side screw to adjust the flame enclosed in a glass, open top shield.A flat wick kerosene lamp. The knob protruding to the right adjusts the wick, and hence the flame size. This lamp has a plain blue glass shade -chimney with a fluted rim, blue glass geometrically engraved reservoir and a circular brass base early settlers, pioneers, market gardeners, moorabbin, brighton, bentleigh, ormond, mckinnon, lighting, lamps, kerosene, paraffin, oil

Lamp used for burning oil. This would have been used to create light prior to electricity becoming the main source.This lamp is part of the story of lighting in domestic and maritime settings. The collection holds a number of whale oil lamps which, alongside kerosene lamps, show the development of different types of lighting.Glass lamp base with metal burner and wick raiser. Has liquid in the reservoir which looks like paraffin or kerosene. The stem has a wide base with a narrow fluted chimney stem. The base is octagonal. The glass is cut and the top of the stem underneath the reservoir has raised ball-like decorations.light, domestic, oil lamp

During the Victorian goldrushes of the 1850s thousands of Chinese migrants arrived to seek their fortunes. At that time many came to the lucrative gold fields of Northeast Victoria. After the Gold rush, many Chinese migrants returned home. However, a number settled in the area as merchants, hawkers and market gardeners in surrounding towns including Wodonga, the Ovens, King, Buffalo River and Kiewa Valleys. They also rented lands and established themselves in the hops and tobacco farming industries. Items of Chinese origin made their way into many households. Importation of Chinese mass produced items such as this lantern continued well into the 20th century and were common domestic items across Australia before households were connected to electricity.This item is representation of kerosene / paraffin lamps used throughout Australia to provide lighting inside and outdoors prior to the widespread availability of electricity.A small hurricane lamp with a rounded tank and small carry handle attached to the top. A larger handle is also attached at the top of the frame. It has a lever to open the glass tank. It has a metal base which is filled with kerosene. It has a screw knob to open the kerosene receptacle. The metal hood also has vents. The Chinese characters around the base translate to "Shanghai Guanghuaheng".Around base : Chinese characters. On top : "Made in China KWANG HWA"kerosene lamp, domestic appliances, chinese artefacts