Used and sold by Holden and Frost in the 1800's and early 1900.sUsed Imported and sold by Holden and FrostBrass saddle that was to be used on Equine accessoriesequine civilian, military, agriculture ca1900, strap saddle

REPLICAAs manufactured and retailed by Holden and Frost Ca1900Metal circular ring with flat base. Slot on top for leather strap from the saddleequine, stirrup

Stirrup used by ladies who ride side saddleAs manufactured and sold by Holden and FrostBlack metal ring with flat base , slot on top to fit leather strap from the saddleequine, stirrup

Leather strap used on carts and wagons going under belly of horse to affix the cart poles for haulageManufactured and distributed by Holden and Frost brown leather strap with tongues attached each end with steel buckles, designed for attachment to saddle strapequine, belly band

Leather strap used on carts and wagons going under belly of horse to affix the cart poles for haulageAs manufactured and sold by Holden and Frost brown leather strap with tongues attached each end with steel buckles, designed for attachment to saddle strapleather, equine, belly band

This stirrup is used by ladies who ride side saddleManufactured and sold by HOLDEN and FROSTMetal cirular ring with flat area on base, on the top there is a slot which is where the leather strap from the saddle is passed throughnilstirrup, equestrian

This stirrup is used by ladies who ride side saddleManufactured and sold by Holden and FrostMetal circular ring with flat area on base, on the top there is slot which is where the leather strap from the saddle is passed through, Painted blacknilequine civilian, stirrup

Item could date later if used by someone wearing ceremonial or uniform dress collars after collar attached shirts became the norm rep[lacing detachable collars for everyday wear.Small leather- look composition board, horseshoe shaped collar box with thin real leather strap and buckle fastening. Saddle stitched on outer edges, inside box is lined with paper printed with faux alligator or crocodile skin pattern in sepia colour.On top of lid in right lower corner: 'Collars' in faded gilt cursive printed text.costume accessories, male, personal effects, travel goods

A brown leather document/map bag. It is envelope style with a rusted silver coloured buckle. On the back is a silver coloured metal ring to attach to a saddle. The flap has a small strap to close the buckle.leather-case document-holder

Used as an overnight bag and was carried at the front of the saddle.Rectangular, brown leather valise with straps on front. Folds in half for storage. To be used in front of a saddle.Written inside: A. Davidson Buchanvalise personal-effects saddle-bag

British military saddle as used in WW1. The saddles were designed to have interchangeable parts, making them easy to repair.Military steel arch brown leather saddle. Tree is made of wood with thick blue felt pads and leather attachments. Neither is original. Various brass rings located on the saddle for attaching sundry equipment. Brown leather strap with silver coloured metal buckle attached to the rear right hand side of the tree. No stirrups, stirrup leathers or girth attached. The leather seat covers the frame of the saddle between the front and rear arches and is connected to them by khaki webbing and leather laces. Leather sweat flaps on each side. Leather straps and brass buckles on the front of each pad.Stamped on the front of the seat: '1916, 13'. Stamped on each sweat flap: '1916, 13'.military equipment, saddle, horse equipment, transport

Saddle bag used during the First World War. This is presumably a dog saddle bag used to carry machine gun weaponry.This item is a piece of equipement that presumably was used as a dog saddle bag during the First World War. As a WW1 item which presumably would have been worn by working war dogs, this item has an unique history associated with it. It is a rare item, it has historic significance and good interpretive capacity as an unusual piece of war equipment.Fabric and leather saddle bag rectangular in shape with curved edge for the curve of the animal's neck. Fabric is beige-coloured on interior and a thicker woven layer on the exterior is brown with black and light green stripes; fabric remains on only half of the exterior saddle and holes throughout remaining. Saddle has leather binding along edges. Each side carries five pockets, the outer two on each side are fastened by metal buckle and the middle remaining unfastened. Pockets are lined with same beige-cream woven fabric. Leather strap fastens around the neck of the animal and is secured with a metal buckle which inserts through one of several punched holes. first world war, world war i, world war one, the great war, saddle, horse, mule, mounted infantry, equine

This belt belonged to a WW1 Australian Anzac who most probably, because of the buttons and badges, served on the Western Front. Records destroyed in 1969 bush fires at Lara means we are unable to determine who owned this in the RSL. The belts is called a 'stable belt' and the one you have acquired is an early example with a leather pocket. It became common in WW1 for both, leather belts (especially that from the 1903 bandolier equipment as worn by those in the Boer War), and stable belts to be used to hold badges collected from fellow soldiers and for that reason it was often known as a 'souvenir belt'. The evolution of the stable belt: It seems that stable belts began to become popular across the Army as a whole around the turn of the 20th century, although they probably originated with the cavalry a little earlier sometime in the 1880s/1890s. All units at that time had horses on their establishment and those soldiers told off to attend them reported for Stable Parade in Stable Dress which consisted of very high waisted and pocket less breeches, or trousers, held up by braces and collarless, woollen flannel shirts with sleeves rolled up. This was to facilitate the rigorous physical effort and flexibility of movement necessary for mucking out and grooming. Braces at that time had no elastic as rubber was expensive, they were made of cotton with no 'give' whatsoever and so soldiers commonly allowed the braces to flop down from the waist so that they could bend over freely. For trousers that fitted loosely (due to the high waist) this meant that they tended to slip down and at first soldiers cinched them in with leather belts. Later on the regimental saddlers began to make belts from the same, plain canvas or wool strapping used for the horses Surcingle and utilising the same double leather strap and buckle arrangement for security (if one strap broke the other would hold and prevent the saddle from coming unseated). One particular feature of these early stable belts was a sewn on (or in) pocket, secured by a stud or clip, within which loose change could be kept, or a pocket watch, as there were no pockets in the breeches. As you might imagine these became very popular as the pocket was useful and the extra breadth afforded by the canvas strapping made them very comfortable. Around about the turn of the 20th century it began to be popular for officers to wear neckties in regimental colours both for sport and less formal, country dress. This habit probably began with the Queens Household troops and Line Cavalry, but quickly spread throughout the Army and it appears as if this use of regimental colours spread to the canvas or wool strapping used to make stable belts. For this reason the stable belts invariably followed the same colour scheme (but not always the same pattern arrangement) of regimental neck ties. This belt is an example of what Australian troops collected when on the Western Front during WW1 and when on leave.Leather Belt with 31 Badges and Buttons from WW1 attachedSee Mediaww1, world war 1, australian army, badges, button, belt, stable belt

This belt belonged to a WW1 Australian Anzac who most probably, because of the buttons and badges, served on the Western Front. Records destroyed in 1969 bush fires at Lara means we are unable to determine who owned this in the RSL. The belts is called a 'stable belt' and the one you have acquired is an early example with a leather pocket. It became common in WW1 for both, leather belts (especially that from the 1903 bandolier equipment as worn by those in the Boer War), and stable belts to be used to hold badges collected from fellow soldiers and for that reason it was often known as a 'souvenir belt'. The evolution of the stable belt: It seems that stable belts began to become popular across the Army as a whole around the turn of the 20th century, although they probably originated with the cavalry a little earlier sometime in the 1880s/1890s. All units at that time had horses on their establishment and those soldiers told off to attend them reported for Stable Parade in Stable Dress which consisted of very high waisted and pocket less breeches, or trousers, held up by braces and collarless, woollen flannel shirts with sleeves rolled up. This was to facilitate the rigorous physical effort and flexibility of movement necessary for mucking out and grooming. Braces at that time had no elastic as rubber was expensive, they were made of cotton with no 'give' whatsoever and so soldiers commonly allowed the braces to flop down from the waist so that they could bend over freely. For trousers that fitted loosely (due to the high waist) this meant that they tended to slip down and at first soldiers cinched them in with leather belts. Later on the regimental saddlers began to make belts from the same, plain canvas or wool strapping used for the horses Surcingle and utilising the same double leather strap and buckle arrangement for security (if one strap broke the other would hold and prevent the saddle from coming unseated). One particular feature of these early stable belts was a sewn on (or in) pocket, secured by a stud or clip, within which loose change could be kept, or a pocket watch, as there were no pockets in the breeches. As you might imagine these became very popular as the pocket was useful and the extra breadth afforded by the canvas strapping made them very comfortable. Around about the turn of the 20th century it began to be popular for officers to wear neckties in regimental colours both for sport and less formal, country dress. This habit probably began with the Queens Household troops and Line Cavalry, but quickly spread throughout the Army and it appears as if this use of regimental colours spread to the canvas or wool strapping used to make stable belts. For this reason the stable belts invariably followed the same colour scheme (but not always the same pattern arrangement) of regimental neck ties.This belt is an example of what Australian troops collected when on the Western Front during WW1 and when on leave.Webbing Belt with Badges and Buttons WW1See Mediaarmy, australian army, western front, aif, s.w.ellis, service number 640, 2 m.g.c., buttons, badges, belt, stable belt

This stock horse bridle was probably used in the mid 1900's. This was the period when cattle and sheep mustering was at its prime. The movement of cattle and sheep was by mounted stock horse only and not by other methods. Northern territory cattle stations in the late 1900's started to use helicopters for "cattle control". In the KIEWA Valley/Bogong High Plains and other rural cattle/sheep producing areas required well trained stock horses and stockmen for cattle/sheep control. It is only in the later 1900's that motor bikes and four wheeled quad-bikes have taken over, in part, from the mounted stockman.This horse bridle is very significant to the Kiewa Valley because of the early introduction of cattle and sheep stations in what initially was regarded as a semi remote valley location. The maintenance of cattle and sheep in the Kiewa Valley was, and still is an important requirement of livestock management. A good stock horse bridle is important, especially during the period when cattle and sheep were grazed on the Bogong High Plains. The mustering and and moving cattle/sheep from the valley pastures to the high country was a demanding and dangerous exercise requiring "sure footed" stock horses.The "good specialised" bridle was a vital part of this cattle/sheep mustering. A scientific study started in 1947 to study the impact of grazing cattle/sheep on the natural Alpine and sub Alpine vegetation found grazing cattle had an adverse affect on the natural Alpine and sub alpine vegetation, and grazing on the plains was stopped by the Victorian Government in 2005.This "camp draft" on the Bogong High Plains could take up to six weeks.This harness bridle includes "blinders, winklers or blinkers" and would therefore be used on a pack or "working" horse. This bridle has rings on each end of the browband. The bridle is one used by a horse working in a team configuration pulling a heavy cart or wagon. The bridle has ten adjustable straps to allow it to accommodate a variety of horse sizes. See KVHS 0495 for a stock horse saddle.horse, country, leather bridle, gaiters, high country grazing, cattlemen, laces, studs

The spur is used in many equestrian disciplines.Most equestrian disciplines have rules covering spur design and use. Spurs are usually held on by a leather spur strap that goes over the arch of the foot and under the sole in front of the boot heel. The stirrup is a light frame or ring that holds the foot of a rider, attached to the saddle by a strap, often called a stirrup leather. Stirrups are usually paired and are used to aid in mounting and as a support while using a horse.E. Fisher grew up and lived at Mongan's Bride in the Kiewa Valley. Horse riding was common in the Kiewa Valley especially before the introduction of motorised vehicles.A spur is a metal tool designed to be worn in pairs on the heels of riding boots foe the purpose of directing a horse to move forward or laterally while riding. It is usually used to refine the riding aids and to back up the natural aids eg. the leg, seat, hands and voice. A stirrup is a light frame or ring that holds the foot of a rider, attached to the saddle by a strap, often called a stirrup leather. Stirrups are usually paired and are used to aid in mounting and as a support while using a horse. The spurs and stirrups are made of steel and the straps of leather.horse riding, spurs for horse riders, stirrups for horse riders, e.fisher

This cartridge bag was taken from Ned Kelly by Sergeant Steele, when he was finally apprehended in the famous shootout with police at Glenrowan, some two years after the Stringybark Creek murders. Sergeant Steele stated that the dark stain on the bag is Ned Kelly's blood: "That is Ned Kelly's cartridge bag. That is the one he was wearing at Glenrowan. I took it off him, with the other things, when he fell. And that stain is his blood. He was wounded in several places, and bled a good deal. Yes it is a grim relic - not at all pretty". (Sergeant Steel) Cartridge bags such as these were worn slung over the shoulder (the strap for this one is missing). They were used to carry ammunition.Bag, saddle, leather with flap and two metal buckles with straps broken. Metal loop and larger metal buckle attached at top. edward kelly, ned kelly, kelly gang, arthur steele, glenrowan

The early settlers of Victoria depended on horse drawn vehicles to farm, make roads and railways, deliver produce and transport people. Horse harnesses were an important requisite for all drivers and could be found wherever there were working horses. Horse Harnesses have played an essential role in different cultures throughout history. Simple, utilitarian horse harnesses made of leather straps and iron rings were being used in early China before AD 500 as well as ancient Greece and Rome allowing horses to pull chariots and ploughs. The Greeks and Romans were the first to use a "horse collar" which distributed the weight of the harness evenly across the horse's chest rather than relying on a "throat harness" that could damage a horse's throat or choke them. During the medieval period, European horse harnesses became more elaborate and decorative. Variations of different horse harnesses were also found in Native American and Middle Eastern cultures. Horse Harnesses usually have four basic components which include - 1. Communication - the bridle, bit and reins allows the driver to communicate instructions and commands to the horse, guiding its movement and direction. 2. Draft - the collar, hame straps, hames, traces and chains enables the horse to draw and pull the load efficiently by distributing the weight and transferring the pulling force to the vehicle. 3. Stopping - the breeching band, pole straps and breast strap helps to control or stabilise the horse and vehicle when moving downhill or stopping. 4. Support - the back pad, backband, belly band and back saddle keep the harness in the correct position and proper alignment. This dray harness is a plain, basic harness and reflects its working class origins. It was used by Mr. Oswald (Jack) Bourke with his horse and dray to firstly deliver drygoods from Sunbury to Melbourne in the 1930's and later (through the 1940's and 1950's up to 1961) when he worked on the garbage round for the Springvale City Council. This horse harness is a significant example of the equipment that was needed wherever horses were being used - particularly in the early years of Victoria's settlement by white settlers. Harnesses such as this example were used with drays, farming equipment, delivery carts and personal transportation.A leather and metal horse harness used with a horse and dray circa 1930's to the early 1960's. It is made up of a number of components. 1. A leather bridle with metal buckles and rings, blinkers and a metal single jointed, snaffle bit that has the initials M B stamped onto the leather. 2. A leather bridle with metal buckles and rings and a metal "straight bar" Eggbut snaffle bit. It has an elongated X design (with 4 dots) stamped onto the leather strap holders near each buckle. 3. A blue and white vinyl halter with one leather patched strap. The nose band and a chin strap are covered with woollen padding. 4. A pair of leather shaft protectors. They have lacing holes along each edge and a repeating design of small shapes (flowers, wings, crosses and arrowheads) which run along the front of each protector. 5. A leather strap with a stainless steel chain and catch and a maker's mark for "Glenn's Leather Goods, Pearcedale Victoria" stamped onto the end. 6. A wide leather strap covered with a webbing sleeve. It has two large metal rings and each end and one ring has a rope attached. 7. A leather strap comprised of three separate sections (two shorter and one longer) joined with two metal rings. The longer section has notches along its length and the shorter section at the other end has a buckle. It also had a maker's mark stamped on it but the mark is very worn and the writing is difficult to read. 8. An adjustable leather horse collar with two buckles and straps at the top opening and two "B's" stamped into the leather. The top of the collar is made from treated leather pieces stitched together and the underneath of the collar is untreated leather. It has a padded indentation running all the way around the collar for the hames to sit in. 9. Two pairs of long leather traces - each having a buckle and notched section at one end and each one is made with three lengths of leather spliced together. 10. A leather strap (with one spliced join) belonging to a horse harness with two shorter straps (each ending with a metal clip) attached to a steel D ring at one end. 11. Three assorted short leather straps - the top one has clips at each end and a buckle (for adjusting the length) in the centre, the middle strap has notches and a buckle and the bottom strap is white with notches and a buckle.Bridle with blinkers - "M B" Bridle - design showing an elongated X with a dot in each section stamped onto strap holder Shaft Protectors - stamped design of flowers, wings, crosses and arrowheads Strap with chain - "Glenn's leather goods / Pearcedale / Victoria" Leather Strap (with two metal rings) - Maker's stamp - "name indecipherable / SADDLER / ...OURNE" Collar - "B / B" Leather strap - flagstaff hill maritime museum and village, warrnambool, great ocean road, sunbury, springvale, dray, delivery dray, harness, horse harness, horse drawn vehicles, working horse, oswald (jack) bourke, bridle, horse collar, hames, shaft protectors

The early settlers of Victoria depended on horse drawn vehicles to farm, make roads and railways, deliver produce and transport people. Horse harnesses were an important requisite for all drivers and could be found wherever there were working horses. Horse Harnesses have played an essential role in different cultures throughout history. Simple, utilitarian horse harnesses made of leather straps and iron rings were being used in early China before AD 500 as well as ancient Greece and Rome, allowing horses to pull chariots and ploughs. The Greeks and Romans were the first to use a "horse collar" which distributed the weight of the harness evenly across the horse's chest rather than relying on a "throat harness" that could damage a horse's throat or choke them. During the medieval period, European horse harnesses became more elaborate and decorative. Variations of different horse harnesses were also found in Native American and Middle Eastern cultures. Horse Harnesses usually have four basic components which include - 1. Communication - the bridle, bit and reins allows the driver to communicate instructions and commands to the horse, guiding its movement and direction. 2. Draft - the collar, hame straps, hames, traces and chains enables the horse to draw and pull the load efficiently by distributing the weight and transferring the pulling force to the vehicle. 3. Stopping - the breeching band, pole straps and breast strap helps to control or stabilise the horse and vehicle when moving downhill or stopping. 4. Support - the back pad, backband, belly band and back saddle keep the harness in the correct position and proper alignment. This show harness was used by Mr. Andy Bourke when showing his Clydesdales at shows or demonstrations. Although a more modern example with decorative embellishments, it still has many essential components traditionally found in an everyday working horse harness. The original purpose of the "housen" for example, was to run rain or drizzle off the horse's neck when they had to work in wet conditions - it was laid flat for this purpose on the top of the collar. Nowadays it is purely for show and is often used to advertise a business or stud. Horse brasses and fly terrets were fastened to various parts of a horse's harness. In the early days they probably began as amulets to ward off evil and to bring good luck and continued to be used as a festive decoration. The heyday of horse brasses was between the years 1851 and 1900. Horse brasses are fastened to various parts of the harness with many of their designs being symbolic. The ornamentation on this harness (although not authentic horse brasses) are based on the horse brasses that were popular in the 19th century. This horse harness is a significant example of the equipment that was needed wherever heavy horses were being used - particularly in the early years of Victoria's settlement by white settlers. Harnesses such as this example were used with stage coaches, drays, farming equipment, delivery carts and personal transportation.A leather and metal horse harness used when showing a Clydesdale (or other breed of heavy horse). It is made up of a number of components. 1. Decorative leather cart saddle with two large cloth pads underneath (which have a scalloped leather and stud border), a raised leather pommel and a silver and red coloured metal back strap holder across the top. It has two symmetrical sets of ornamentation (silver hearts and circles) in the front and a wide strap or girth (with a maker's stamp reading "R. Mitchell Saddler") and buckle which attaches the saddle to the horse. 2. Pair of steel hames which are gently curved (to fit on a horse collar) and are topped with steel knobs. They have several steel rings and lugs (to hold straps and chains) and a "Made in England Warranted Steel" stamp. 3. Breeching harness which consists of a number of leather straps, chains and metal rings including a wide padded leather strap with a scalloped edge that sits on the back of the horse and a thick leather strap that goes around the hind quarters of a horse which is joined to the back strap with four shorter vertical straps and buckles. These straps feature silver and red patent leather trim and silver heart shaped ornamentation. The strap also features the maker's stamp of "R. Mitchell". 4. Decorative leather bridle with blinkers featuring the same silver and red patent leather trim on the cheek piece, brow band and throatlatch. It has a stainless steel "Liverpool Driving Bit" with a curb chain, a variety of decorative silver ornaments (rosettes, diamonds plus a heart and two circles) on each end of the forehead band, dropper and strap as well as a silver metal bell (sometimes known as a "fly terret" or "swinger") that sits on the headpiece of the bridle. 5. Leather "violin shaped" dropper (or hanger) with two silver rosette shaped ornaments and a stainless steel clip on the top 6. Stainless steel "Liverpool Driving Bit" with a straight mouthpiece which is ribbed on one side. It has three rein spots (spaces) and a curb chain. 7. Leather arch shaped "Housen" covered in black and red patent leather and decorated with silver studs (some spelling out F H) and bordered with a red fringe. It has a leather strap at the back and two leather loops on the front. 8. Leather padded backband (Australian style "Stallion Draught Roller") decorated with two groups of nine metal "horse brasses" or harness ornaments displaying horseshoe, starburst and horse head designs on blue, red and white striped webbing. The backband has three notched straps at each end, a buckle near the centre and the initial B stamped in two places underneath. 9. Bellyband made of leather and red, white and blue striped webbing. It has a set of three buckles at each end (which correspond with the notched straps of the backband). 10. Wide, thick leather strap which has a buckle and notches at each end. It also has the maker's stamp of "R. Mitchell Saddler". 11.One pair of long leather traces - each with a buckle and notched loop at one end, decorated with a small silver diamond shaped harness ornament. 12. Length of stainless steel heavy duty chain with two swivel connectors.Saddle - "R.MITCHELL / SADDLER" Hames - "MADE IN ENGLAND / WARRANTED / STEEL" "MADE IN ENGLAND / WARRANTED / unclear" Breeching Straps - "R. MITCHELL / MAKER / R. MITCHELL MAKER" Housen - "F H" Backband "B / B' Wide leather strap - "R. MITCHELL / SADDLER"flagstaff hill maritime museum and village, warrnambool, great ocean road, shipwreck coast, harness, horse harness, show harness, clydesdale horses, andy bourke, horse drawn cart, housen, bridle, hames, breeching straps, dropper, bit, liverpool bit, backband, harness ornamentation, bellyband, back saddle, fly terret

In the 19thC and early 20thC men often wore their shirts for a week or more. However the collars were detachable so that they could be changed when they became dirty or for special occasions eg Church on Sundays Collar studs were used to attach the collar to the shirt. The leather box was used for storage and when travelling. The collars were very stiffly starched so as to maintain their shape.The Blackburn family were early settlers in Moorabbin Shire4 x mens white, stiffly starched, detachable collars and 2 x brass studs with the leather box used for storage and transport of these items. Each collar has 3 button holes - 2 at neck and 1 centre back for attachment to the shirt. The Leather box has saddle stitching and a strap with a metal buckle for securingInside collar : a) Radiac / 0 2639 - 16 / ALL COTTON / MADE IN IRELAND; b) LAUNDRY / FOR BEST RESULT DIP / IN THIN COOKED STARCH/ Semi / 161/2 ; c) nil d) nilmenswear, clothing, shirts, collars, early settlers, fashion, cheltenham, moorabbin, dairy farmers, market gardeners

Leather straps were commonly used to secure cases and other forms of luggage when traveling. The labels enabled easy identification when collecting luggage from transport carriages, coaches, buses and trains. 10th Field Company, Australian Engineers WW1 1914-18. The 10th Brigade was an infantry brigade of the Australian Army. Originally formed in 1912 as a Militia formation, the brigade was re-raised in 1916 as part of the expansion of the Australian Imperial Force following the end of the Gallipoli campaign. It subsequently saw service on the Western Front in France and Belgium during the First World War. After the war it was disbanded but was re-raised in 1921 as a part-time formation based in the state of Victoria. During the Second World War the brigade was used in a garrison role in Australia before being disbanded in 1942.These leather straps and labels were attached to the luggage of an Australian soldier during early 20th C who may have been a resident or relative of a resident in City of MoorabbinLeather luggage straps with metal buckles and 3 luggage address labels attached.Label 1 - L.D.McCallum Sgt / 10th Fd Coy AE Label 2 - Healesville Label 3 - Maryborough leather, straps, belts, luggage labels, tools, saddles, wallets, personal effects, horses, drays, world war 1 1914 -18, world war 2 1939-45, army, 1st aif, military, 10th field company australian engineers, western front, france, belgium,

John Oxley was a shoe and butchers’ knife manufacturer, who was listed in Whitecroft UK in 1822 . By 1825, he was based in Hollis Croft. John apparently died in about 1837. He had two sons – George (1808-1879) and James (1811-1881) who took over the business. George moved to Indianna, USA and in 1868 James continued to manufacture 'Cooks’ and palette knives and steels" Oxley’s trade mark was a butcher’s knife crossed with a sharpening steel (and the letters ‘JO’). The firm stayed in the family until 1960. Early settlers were self reliant and repaired their own equipment for kitchen,dairy, farm, horses, carts using various tools . This strong steel knife is typical of the type used by early settlers in Moorabbin Shire c1900Heavy duty curved steel knife with a wide blade encased in 2 thick leather straps secured with steel rivets Blade ; James Oxley with Trade Mark - a butcher’s knife crossed with a sharpening steel (and the letters ‘JO’). scratched into leather handle ; J EVANSknives, sheffield steel, oxley james ltd. , leatherworkers, saddles, horses, bootmakers, shoes, boots, builders, carpenters, early settlers, market gardeners, blacksmiths, tools, building equipment, hammers, moorabbin shire, bentleigh, mckinnon, highett, cheltenham,mcewan james pty ltd, melbourne, bunnings pty ltd,

Track cycle built by Eugene Cowley in 1949 for Ken Jenkin from the Geelong Amateur Cycling Club.Gene Cowley began building cycles in the 1890s and continued until the middle 1950s. He was the first president of the Geelong Amateur Cycling Club.Velos Track and Road Cycle. It has a steel frame, steel rims, rubber tyres, Brookes saddle, pedals with toe straps, handle bars for track racing and dual brakes. This machine is equipped with an early derailler gear- note change lever on down tube. The frame is painted grey and has a Velos badge on the seat stem and a V in white with a red background on the head stem. The word Velos is also outlined on the frame in white with red shadowing."Velos/V"ken jenkin; eugene cowley; geelong amateur cycling club; track cycle; velos track and road cycle; brookes saddle; geelong cycling club;

Rifle buckets were used by British and Commonwealth mounted troops from the First World War to around 1941. In the Australian Light Horse units their use did not become common until the end of the First World War. Prior to this rifles were carried slung across the rider's back.Long cylinder shape made from dark brown leather with leather strap and brass buckle at the top of the bucket which attaches it to the saddle .The bucket is missing a leather slide steadying fitting, half way down the bucket which attaches to the surcingle of the saddle.rifle bucket, light horse

Leather saddle with wooden and metal tree and girth straps. The seat is supported in the centre by canvas webbing (similar to uniform belts worn by infantry) Saddle does not have stirrups or stirrup irons. Three belt attachments on each side of saddle. No markings

Used as footrest for horse riding. Attaches to a strap which attaches to a saddle.Stirrups x 7, dome shaped. Various shaped footrests} 2 oval ring shapes, 2 oval shaped rings with middle strip & 3 solid oval shaped.

WWII HeritageFrom Australian War Memorial: Standard issue blocked brown leather rifle bucket for attachment to the Pattern 1912 UP saddle. Bucket is complete with a leather slide steadying fitting, half way down the bucket, to attach it to the surcingle of the saddle, and a leather strap with brass buckle at the top of the bucket which attaches it to the saddle tree.Strap only is stamped with a broad arrow and manufacturer's details 'BLACKMAN LEATHER GOODS LTD. 175 BERMONDSEY ST S.E.1 1940'.

Each light horseman carried two spare horse shoes and nails in a wallet or case attached to his saddle. The wallet was attached to the near (left ) side of the saddle and a sabre could be secured in the loops on the side of the wallet. Stamps on the underside of this wallet indicate it was used by a trooper of the 13th Light Horse Regiment during WWI (1914-1918). It is possible the wallet was issued to Regimental Number 280 Trooper H B Johnson. The 13th Light Horse Regiment (AIF) was raised at Broadmeadows Victoria in March 1915. Following service at Gallipoli the regiment was broken up with squadrons going to France as Divisional Cavalry Squadrons of 2nd, 4th and 5th Divisions. The regiment was reformed as firstly 1st Anzac Corps Mounted Troops and later Australian Corps Mounted Troops. The regiment was raised as 13th Light Horse (Gippsland), a Citizen Forces unit. following WWI, and trained as a cavalry regiment till August 1940, when it converted from horse to mechanised initially as 13th Motor Regiment then 13th Armoured Regiment. It trained in Victoria and, as the Japanese threat to the mainland declined, was disbanded in October 1943 with men going to other units. unique relic of the Australian Light Horse in WWI.Leather wallet containing two spare horse shoes to be attached to saddle by light horseman. loop on side and securing strap held cavalry sword if trooper was issued with one.CGHF / B / 13 LH / 280military, horse, shoe, wallet, case

Part of the saddle equipment of a Light Horse Trooper. the loop and strap on side was to secure a sword.Leather wallet holding two horse shoes. Manufactured by the Commonwealth Government Harness Factory (CGHF) Groom Street Clifton Hill Victoria.CGHF / 337horseshoe, wallet, light horse