The colour prints show a Prahran and Malvern Tramways Trust - PMTT electrical switching or cable pillar box in City Road, near Queensbridge St, South Melbourne.Yields information about a former PMTT Electrical switch boxSet of 2 colour prints on Crystal Archive paper and 35mm negatives.tramways, pmtt, electrical engineering, electrical equipment, electrical switching, switch box

Black and White - tram 17 (Grey St Sebastopol), arriving at the City tram stop, Sturt and Lydiard Streets, Ballarat. Has the Commonwealth bank building in the background along with an ESCo/SEC switch box. Taken by A T Miles 26/8/1971.Yields information about tram operations in Ballarat, shortly before the closure.Photograph - black and white print with notes on rear. A T Miles stamp and location and date notes.tramways, trams, sturt st, tram 17, commonwealth bank

Photograph - Black and white of an Electric Supply Co. pillar or switch box, cast iron, with the company on the side and on the base "The British Insulated Wire Co. Ltd Prescot England". This type of item was used to terminate and interconnect feeder cables in both Ballarat and Bendigo.Yields information about the ESCo switch or cable pillars.Black and white photograph on plain paperIn ink on rear "R Green photo" and "See composite caption" which has been crossed out.tramways, tramcars, esco, electrical switching, electrical equipment, british insulated wire company

Wooden box used to advise other stations - Box Hill and Ringwood when the Mitcham train was departing. Acquired when the Mitcham station was demolished in 2014. Handset altered c. 1970s.Metal plate with switches. Wooden box 1930s. Handset altered C.1970s as used by trains as they departed from Mitcham to Box Hill and Ringwood. Switches Black - Up to Box Hill and Down to Ringwood. Red "UP" Bell to Box Hill Red "Down" Bell To Ringwood To advise the train had left Mitchammitcham, box hill, ringwood, victorian railways, railway stations, trains, railway signals

Type of switch fitted to Melbourne W class trams for switching the line breaker on or off. This switch controls power to the line breaker activated by the tram controller. Had been fitted to the Restaurant tram No. 3 or Cuthberts 939. Was found to be defective - the power was available to the controller even when switched to the OFF position, that is, failed unsafe. Was replaced 4/11/2015 from a spare. Has the name of the manufacturer on the cover. Demonstrates a switch that failed unsafe.Tramcar equipment - line breaker switch - fibre material box and cover containing electrical switch and 10Amp Cartridge fusew class trams, cuthberts 939, switches, line breakers, faulty equipment, safety

Yields information about the intersection of Sturt St and Drummond St and its use by trams in the period before the closure of the SEC system.Set of two Black and White photographs of trams near the intersection of Sturt St and Drummond St North, Hospital Corner. .1 - No. 41, another bogie and a single trucker travel along Sturt St south, the last tram has a destination of Special. .2 - Photo looking at the median strip with a tram on either side. Single trucker with a Twin Lakes sign inbound and another single truck outbound. Shows the position of the shelter and the ESCo switch box. Has a Marshal battery advert on a building in the background. Photo by Charles Craig - during 1971. trams, tramways, sturt st, hospital corner, drummond st, tram 41

Negative No. N380 and black and white print made by a laser printer (stored in folder) of Ballarat No. 25 at the City Terminus, Sturt St, south side. Tram has destination of "Sebastopol" with a Bourne? Liquid Plastic (varnish) ad on the front panel of the tram. Has the Commonwealth bank in the background. Adjacent to a pole is a ESCo / SEC electrical connection / switch box on the left hand side of the tram, which is part of the power supply or distribution system. Date of photo on folder - 5/9/1959. Original negative rescanned 24/5/2020 and image file updated. Paper folder that contained the negative had "NR7A" in red ink, "BA7" in pencil, date stamp of "5 Sep 1959" on front, and on rear date stamps "26 Sep 1962" and "26 Sep 1962".trams, tramways, city terminus, sturt st, commonwealth bank, power supply, tram 25

Black and white print of bogie tram No. 22 and another single trucker at the City terminus, Sturt St, with the Town Hall in the background. A large number of passengers board and leaving the trams. Has a bus in the distance crossing Sturt St.. Tram has the destination of Sturt St. West. In the photograph are Anderson Paper Merchants, Terminus Cafe and Penfolds Wine shop. In the bottom right hand corner is an ESCo/SEC cable termination/switch box. 3217.1 - original photo ex SEC? 3217.2 - different crop - added 21/3/2021 - has more of the original image on the right side. On rear of photograph is a white dot with "5" in red ink, and in pencil "Car 22, renumbered as 37 in 1951 in order to consolidate the bogies cars from No. 34 onwards. This was the first bogie car to run in Ballarat and ran from 1945. The car was withdrawn in 1955, following severe accident damage SECV"tramways, trams, sturt st, city terminus, bogie trams, esco, tram 22

Yields information about Sturt St between Lydiard St and Ripon St.Set of 5 AGFA slides - blue and white plastic mounts: 1 - Sturt St looking west, south side from Windermere St. .2 - ditto from Dawson St, shows tram stop sign and end of section sign. .3 - ditto from Armstrong St - with Myer's and Coles stores in the background. .4 - ditto at Ripon St, showing junction of View Point line, has the shelter on the right. .5 - City terminus - Sturt St and Lydiard St, with a bogie tram arriving from Grenville St. Has the ESCo switch box in the view - (to the right of the ladies). Has the Commonwealth Bank on the right hand side of the photo. Photo from the collection of Lilian Butler. ballarat, tramways, trams, sturt st, dawson st, tram stops, view point, shelters, lydiard st

Yields information about the appearance of the appearance of the SEC tram stop equipment at the corner of Ryrie and Moorabool StreetsBlack and white digital print from scan of a donated negative showing the signage at the tram stop in Ryrie St at the corner of Ryrie and Moorabool Streets Geelong. Shows the End of Section, pole banding, Cars Stop Here Sign and a section isolator switch box. Has the Australian and New Zealand Bank Limited, L. N. Hill Estate Agent, Wrays Furs and Bags and F.H.Wray Building in the background. Alongside the ANZ bank building is a number of potential passengers, ladies and gents in overcoats. Assumed photo taken on the same day as the others - 21-8-1955. Black and White prints made from scan of negative. Original Negative stored with Negatives. Negative scanned at hi res 4/6/2020 and image updated.On left hand side of the negatives in ink is "DB12"tramways, trams, geelong, tram stops, moorabool st, ryrie st

Instruction - 5 pages - duplicated foolscap sheets - headed "MMTB Engineering Department - Workshops and Running Shed Branch" - titled "Duties of Electrical Mechanics - Runningsheds" Details electrical work to be done on tramcars at the 100 hours service; trolley pole, electrical equipment, controllers, switches, resistance boxes, line breakers, RC units, motors, governor, compressor, lighting, buzzers, door engines, wipers, brake cylinders and general body eg handrails. Dated May 1970.trams, tramways, depot, safety, workshops, electrical equipment, instructions, procedures

12 Volt battery supply. Green metal box with switches & knobs on top. Army issue used in conjunction with head set for communication APC issue. Radio set from APC used in training?battery

Yields information about the electrical power supply and overhead switching for Ballarat in 1914.Rolled drawing showing Tramway Power supply arrangements 1914, track map, power station, feeder cable, switches, section insulators, box locations, lightning arrestors and feeder cables for the various routes in Ballarat. Dated 2/1/1914, with initials GL. The various cables and trolley wire has been drawing in differing colours.ballarat, power station, overhead, section insulators

Yields information about Ballarat Tramways and trams prior to the closure of the tramway system.Set of 10 digital images of Ballarat trams prior to closure, scanned from original slides by Stuart Lodington, 1971 prior to closure of the system. .1 - No. 17 at the City Centre, Sturt St, south side, with Gardens via Sturt St on destination roll. Can see the ESCo switch box in the back and the stop and section sign on the adjacent pole. .2 - No. 26 at Sebastopol terminus alongside the Royal Mail Hotel. The tram has yet to turn the pole or the destination roll. Note the Bus Stop sign on the pole, just prior to closure. .3 - ditto .4 - No. 27 and 30 crossing in Skipton St at the Bell St loop (see also btm4975i3) .5 - No. 32, Gardens, about to enter the Carlton St loop, with Lake Wendouree in background, Wendouree Parade. .6 - No. 32 at Depot junction, good photo of depot trackwork entry area. .7 - No. 21, Wendouree Parade, Gardens area, north bound, showing Gardens via Sturt. .8 - No. 12, inbound on Sturt St west at a tram stop. Has destination of Mt. Pleasant. .9 - No. 27 at Lydiard St north terminus with the shelter in the background. .10 - No. 21 at Gardens Loop, tram has destination of Mt. Pleasant. Crews sitting in the saloon.trams, tramways, ballarat, sturt st, sebastopol, drummond st sth, wendouree parade, carlton st, depot, depot junction, trackwork, gardens, sturt st west, crews, tram 17, tram 26, tram 27, tram 32, tram 21, tram 12

Ten page plus cover sheet document titled "Scrubber No. 8 Training Manual", detailing Controls, Auxiliary equipment of ex MMTB Scrubber No. 8 ( 8W), with photographs of the controls, scrubbing blocks, pipework, preparation, operation, stabling, appendix showing cut out switches and tool box and Scrubber car operator competency sheet. Version 1, dated 8/6/1001. (has been replaced since). Prepared by Warren Doubleday 6/2001.trams, tramways, scrubber tram, btm, manual, instructions

Agfa plastic mount (blue base, white cover) of a photograph of No. 43 turning from Drummond St South into Sturt St at Hospital corner. Has the shops on the south west corner in the background. Photo taken late 1960's. Tramcar has an SEC roof advertisement. Note the ESCo electrical switch/junction box in the photograph, to the left of the tram. A single truck tram is in the background and the short stubby tram stop pole in Drummond St. South. The slide appears to be a copy slide, given the nature of the colour and the additional number WP415. Photographer could be Bill Pearce (WP). Slide rescanned at 3200 dpi 25-10-2020, jpg replaced, tiff file retained. This file was scanned in 2003 and may show colour changes."BAS 55 in penciltramways, trams, hospital corner, drummond st, sturt st, tram 43

Manufactured in the 1960s, this mobile emergency telephone exchange was fitted into a caravan. Part of the Shepparton Division State Disaster Plan, the caravan could be towed to areas affected by disasters to enable communications to recommence. The caravan remained in service until approximately 1974.Mobile infrastructure plays an important role in Australian communications, owing to the often remote and hostile environments in which Australians live and work. Exchanges such as this facilitated phone calls in the aftermath of an emergency, particularly for hospitals, police and other emergency services. Today, Mobile Exchange on Wheels (MEOWs), Cell on Wheels (CoW) and Satellite Cell on Wheels (SatCOW) - which provide temporary landline and broadband services, mobile phone coverage and service in areas without communications infrastructure respectively - are a critical part of emergency response procedures for natural disasters such as fire and flood. Though technology has progressed, the need for rapid service in remote areas remains a present concern of the communications service providers in Australia. This mobile service infrastructure is historically significant as an early example of a service which has evolved over decades, yet is still needed today. The exchange, as a representative example of a vehicle which would provide early-response in a disaster, is socially significant as a facilitator of critical communications needs in devastated communities: access to emergency services and contact with family and friends. The exchange itself, intact from its period of use, provides an insight into technology of the 1970s.Mobile emergency exchange housed in a caravan trailer on 2 wheel base, duralin body, steel tow bar, Caravan divided into 3 sections; the exchange room; the relay room and the main frame room. The exchange room contains 3 switchboards, a folding table, cupboards, benches and switch rack (.1). table (.2), steel bar for attaching the table (.3), back boards of switchboards (.4-.6), switches (.7-.16), box of switches (.17). There is a wall phone magneto, 300 type handset on wall and 2 skylights with wire screens. .11? hat pegs and shelf; there are 2 fluorescent tubes for lighting, all in exchange section. The floor is covered with 2 tone grey tiles and there are wire mesh on outside of windows and a geometric curtain inside behind switch rack. There is a flywire screen door as well as exterior door. The relay room has a sectioned door so half can open at a time. Room contains a cupboard with folding bench top beneath a curtained window. The opposite wall has a bank of batteries and transmission condensers; there is a shelf above window, one fluorescent tube and fuse boxes. Tiles on floor also. The main frame room contains many metres of coiled black covered cable, a black covered magneto wall telephone with 300 type handset; grey plastic jumper cords, a rack of termination points and wire with wasp nests attached. There is a small iron step under door, a fluorescent tube on wall and 3 hat hooks. Roll of Paper Handtowels (.18), cord and handle (.19), red exchange cords and plugs (.20-.22), plastic aluminium runners (.23,.24), headset (.25,.26), logbook (.27), battery readings (.28), box containing papers circuit drawings etc (.29-.93), paper lists off wall (.94,.95). Books, record books etc (.96-.103). Manila folder (.104) containing circuit drawings (105-.124). Wooden drawer (.125), metal drawer containing subscribers master cards, record of faults cards, particular switchboards connected, Junction line cards (.126). Box of valves (.127), box of clamps (.128). Box of 2000 type rack fuses, red 1 1/2 AMPS, black 3 AMP, blue 1/2 AMP (.129). Box of sleeves for covering wire joints (.130), plastic beakers (.131,.132), soap (.133), box of white plastic squares (.134), time switch "Venner BF/43 time switch" Made in England (.135), box of bolts, knobs etc (.136), box of switchboard number indicators (.137), fuse (.138), fuse wire (.139), football card (.140). Box of cartridge fuse 6 AMP (.141). Envelope of drawing pins, rubber bands (.142), black plastic, paper tape centres (.143-.152), metal plug (.153), 2 signs "Beware of vehicles" (.154-.155). Paper listing Naringal East automatic conversion (.156). Green Commonwealth of Australia note pad (.157). Wiring plug for tail lights (.158). Black fuse plugs (.159,.160). Box of bolts (.161). 2 sections of blue plastic coated wires (.162,.163). Gloves used for working on batteries (.164-.167). Wasp nests (.168,.169). White fuse (.170). Photographs of van in use (.171,.172)..1 on front: "ANOTHER / MOBILETRAIL / PRODUCT" "MAX SPEED / 25MPH" "TRAILER BRAKES / --- / " On sides: "EMERGENCY TELEPHONE EXCHANGE" "NO 1" "PMG" "TCQ / GROSS 250 / TARE 182 / LOAD 162" "6" "COUNTRY BRANCH / NORTH REGION / [SHEPPARTON DIVISION]" "LAW'S SIGNS" "Telecom Australia" On back: "DANGER / LONG LOAD" "MQA 3787" .133: "FIR OIL" "AUSTRALIA"mobile telephone exchanges, mobile telecommunications trailers, trailers, transport, natural disaster, black saturday, bushfires, floods, emergency communications

Mrs Coels was born in Warley Hospital and lived all her life in Ventnor.invitation Card to Switching on of electricity supply to Ventnor District, Friday 13th December 1963. Mrs Edith Coels performed the switch-on ceremony. Card in Presentation Box - Picture FrameCommittee of Ventnor No. 2 S.E.C. Extension Group Switching On Ceremony At Ventnor Hall on Friday, 13th December, 1963 at 8 pm McNabb's Orchestra Good Supper Ticket 7/6switching on ceremony ventnor, mrs coels, cefn & phillis price

Possibly early 1950sDark brown box with lid and clip fastener. The lid has a handle at the top.Lid & inside of box lined in red velvet. There is a separate narrow compartment for the reel. There is an electric cord and 3 papers. The reel is dark grey steel. The cord is brown rubber and very long. At the front is an attached plastic label with a switch in the centre. There is a black, red and gold disc with a Bell and Howell guarantee. A Registration card indicating model 606 & Serial no. 9039 and another card with a Safety message in 8 languages.On the base: G.B. Bell & Howell / 8 mm projector / Model 606 / 110-250 / volts / 5 Amps A/C/ or D/C/ England London. Above this label is : Lamp 400 Watts Max.. 9039 is printed in silver on the side. Inside bottom of lid: Cabinet by Raddports Pty. Ltd. / NSW / Leatheretteprojector, g. b. bell & hovell

This is the MINJAH telephone exchange testing unit. The exchange was adjacent to the property of MINJAH which is situated near Hawkesdale in Western Victoria. The exchange operated between 1955 and 1985. The testing unit was used for detecting and testing faults in the telephone system. The keys along the front were called "Hospital Keys" and were used to give subscribers a temporary connection in the event of a break down. The telephone exchange was replaced by an automatic exchange.This is a good example of a manual telephone system in Western VictoriaThis is a rectangular polished wooden box with a telephone mechanism on the side connected by a hook. On the front right is a dialling system which has been detached. On the front left is a volt meter. At the front bottom are seventeen switches. In the middle front are twenty keys which can flash up in various colours. There is writing on the side . There is a black metal label with writingAVD HAND SET S314470 c 7060 H/56 LINE & SELECTOR TEST SET HT& Co. Ltd. LIVERPOOL ENGLANDtelephone testing, minjah, manual telephone exchange

On reverse: Tiros II - Taken from above with cover removed: 1. Wide angle TV camera 2. Narrow angle TV camera 3. TV tape recorders 4. Infra red - 5 channel radiometer 5. Infra red electronics 6. Electronic operations sequence timing 7. Relays for magnetic stabilisation for altitude 8. Control box for electronics 9. Infra red horizon scanner 10. Electronic camera circuits 11. Electronic TV tape circuits 12. Telemetry switches 13. Antenna diplexer (covering storage batteries) 14. Automatic signal generator 15. Fuse board and current regulatoralan gardiner collection, space industry, 1960, satellite, tiros ii

Precision instrument used meteorological offices on air fields to measure barometric pressure141.1 Metal cube shape instrument with button switch attached is a cylindrical read out and adjuster knob. 141.2 Carry box with hinged lid and metal latch, has three hold down screws. 141.3 Stainless steel and glass thermometer 141.4 batteries 4x 15v. Standard batteries were HT Eveready B123 30v x3, LT Eveready LLII 1.5 v x1Aneroid Barometer, Type No. M.1991/A Range 800-1050mb. Ser No. 686/65, Mechanism Ltd, Made in Englandbarometer, instrument, aneroid barometer, thermometer

Worn by Swinfield in IraqWorn by Swinfield in IraqBlack edge trimmed green fibreglass Army vehicle intercom helmet. Adjustable head straps inside helmet, Adjustment strap for right earphone located on ouside of right ear. Earphones mounted inside helmet at each ear side. Voice microphone located at mounting on outside of the left ear connected by black cable to mounting on outside of left ear. Cable connection with clip for helemt connection to vehicle located at outside of left ear. Switch located on mounting on outside of left ear. Plastic mounting box located on ouside of the left ear. Brown leather sweat band on helmet straps on inside front of the helmet. Male and female connections on end of vehicle connection point.Swinfield marked on outside front of helmet. 34B marked on outside of helmet at rear. Roamwell Corp. with number SA-1552,6 marked on plastic mounting on outside of right ear. Front and back markings on microphone. M138/6 marked on back of microphone. ID label on connection point end of vehicle connection cable.

Small rectangular cardboard box containg a black cylindrical metal and rubber flashlight or torch. The outside of the cardboarch container has black ink markings for identification and manufacture. A white printed ID label containing a barcode is attached to the bottom of the box. The pocket light has a metal attachment clip on its side and a rubber covered on/off switch on the bottom of the light. The body of the light has a knurled section for grip. The lens top section of the field pocket light unscrews of the body to enable the top of the pocket light to be unscrewed to enable battery insertion.FPL-3000 Military Pocket Light Made in Australia NSN no: 6230 66 139 1304 Ocean Graphic Pty. Ltd. Melbourne, Victoria, AUSTRALIA. *6230661391304023* FPL-3000 Black/Green Filter The field pocket light has the NSN marking 6230-66-139-1304 with the Department of Defence arrow marking at the side of the top of the flashlight.fpl-3000, military, field pocket light, australian military

A machine fitted with sharp blades, for mashing, crushing or liquefying food ingredients. i.e vitamizing. The jug, made of glass, steel, aluminium or plastic, contains rotor blades that engage with a bit protruding from the base containing an electric motor. When activated by the switch on the base the sharp rotor blades chop, mix , mince, pulverize the ingredients in the jug . The degree of mince depends on the time the motor is running. The jug is easily removed from the base to pour the mixed ingredients where needed and the rotors are safely and easily cleaned by rinsing under water.c1940, an electric, 'Vulcan' Vitamizer, with the original cloth covered flex and bake-lite lever switch at front of the cream bake-lite base . The jug- shaped chrome blender has a red, thick, rubber lid. Front: : Vulcan / LM1 Base ; VULCAN / TYPE LM1 / Patent Pending Design / Volts 220 Amps 8vitamizer, food preparation, cooking, vulcan pty ltd australia, moorabbin, bentleigh, cheltenham, ormond, housekeeping

This field telephone was developed primary for military purposes (World War I) and other wars/military interventions there after. It was the first "mobile" telephone which had a prime objective of providing isolated or "hard" to connect with locations instant communication links. Like a lot of "new" technologies it evolved from a war environment. This handset was used to connect offices and workshops, which due to their functions could not be co-located with their prime office(external workshops).The evolution from the early 1900s to the mid 1980s when mobile communication technology progressed in leaps and bounds from hard wire telephone communication to mobile digital receivers. This handset was manufactured by a subcontracted Australian company under the Australian Post Office mandate.This handset is significant in that it was donated by the Mount Beauty Timber yards and formed an integrated part of its communication system with its out lying work yards and buildings, before the mobile handset evolution. This handset was located in an environment which required a rugged and reliable day to day communications linkage as a vital part of its logistical (business) survival. As progress demands it, the faster that customers are satisfied with the service they obtain from suppliers the longer those services will be asked for and the longer and more profitable the supplier will be. This edict is as true for rural companies as it is for small or large city businesses. The customer is "always" right.This sturdy field telephone has a shell housing made in black bakelite material with a "U" form housing the major components (wiring, magneto and batteries). The main housing has two metal bells, with a central ringer between both, on the top part (to notify incoming calls). In front of the main structure is a box with the telephone hand piece (ear and mouth receptacles) nestled on two cradles. An on/off switch is activated when handset is removed from its cradle. On the front of the control box is a winder handle(to ring off) and in a field situation to activate/deactivate the magneto. To the left of the winder but on the the main body are two wind up connection buttons for the connection of operational wires (power)On the main right hand front body and next to two chrome switches is a plate with "L (next to the top switch) and below this "L2" and underneath this are "or" "EARTH". There is a plate fastened to the front of the handset and behind the winder with "REPLACE HANDSET WHEN FINISHED" and below the winder 'SERIAL NUMBER 5116"field telephone, world war ii field telephone f mk i