Colour photograph of the train turntable and William G. Pert Railway Workshops of the Diamond Valley miniature railway. A number of locomotives are visible.eltham, diamond valley railway, eltham lower park

Ballarat East Railway StationColour photographs showing the train turntable at Ballarat East.ballarat east railway, turntable, railway

Colour photographs showing the train turntable at Ballarat East.ballarat east railway, ballarat, railway

Ganger's Trolly Turntable When a railway gangers trolly was working between railway stations, occasionally it was required for the line to be clear for trains to operate. Many trollys were too heavy to physically lift off the track, so a turntable was needed. These were provided at designated locations, and in some cases the trolly had a turntable on board. The turntable would be placed on the rails and the trolley driven onto it. The turntable would then be rotated 90 degrees by human power and the trolley pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location. Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolly TurntableGanger's Trolly Turntable made of wood with wrought iron fittings puffing billy, ganger's trolley turntable, trolley, trolly

Large Gangers Trolly Turntable Many trollys were too heavy to physically lift off the track, so a turntable was needed. A railway gangers trolly was required to be "off tracked" at its working location, so that it would be clear for trains to operate. A special track at right angles to the running line was usually provided. When all the work was completed and after all the trains had cleared, the trolly was then "on tracked" so that it could proceed to its next location. These turntables were also in use at the Works Depot location. They were provided at designated locations, and in some cases the trolly carried a turntable on board. To allow for more than one trolly to be taken off the line, a longer version was available for use. The turntable would be placed on the rails and the trolly driven onto it. The turntable would then be rotated 90 degrees by human power and the trolly pushed off on to a prepared set of rails on the side of the line. The turntable would then be removed from the track allowing trains to run through that section. The gang could then get on with the work required near that location.Historic - Railway Permanent Way and Works - track equipment - Ganger's Trolley TurntableLarge Gangers Trolly Turntable made of wood with wrought iron fittingspuffing billy, gangers trolley turntable, trolly, trolley

Beech Forest Railway Station was constructed in 1902 and had a number off additions to it over the years. At the far end of the station in 1902/3 was constructed a 'balloon' reversing loop, rather than a turntable or a triangle, which rolling stock used in order to even the wear on the wheels. However, the trains also used it. The Garrett in particular was supposed to be turned every second trip to even out its wheel wear, although this was usually ignored for other reasons. The loop was used throughout the life of the station.Colour. Beech Forest Railway Station showing the 'balloon' reversing loop at the far end. The tennis courts and shelter are in the background.beech forest; railway; balloon loop;

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community. Cudgewa Line -The Cudgewa railway line opened in stages between 1889 and 1921. The first section from Wodonga to Huon opened on 10 September 1889. It was extended to Bolga on 18 July 1890, Tallangatta on 24 July 1891, Shelley on 13 June 1916 (the highest station in Victoria), Beetomba on 10 April 1919 and Cudgewa on 5 May 1921. In 1919, the line was used to carry materials for the construction of Hume Weir, and three years later a spur line connecting Ebden to the weir was opened. In the 1960s, Cudgewa became the railhead of materials for the Snowy Mountains Scheme. The last passenger service from Wodonga to Tallangatta ran on 30 September 1961 The turntable and passenger platform at Cudgewa were abolished in 1976.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.What remains of the Cudgewa Railway Station taken in January 1989. A disused shed in a paddock is all that remains of a once busy station.railways wodonga, fred rochow, cudgewa station, high country railway line

The Fred Rochow Railways Collection incorporates photos related to the operation of the Wodonga Railway Station including different types of trains and railways staff C. 1930 – 1990. It was donated to the Wodonga Historical Society by Fred Rochow, a railwayman who spent many years based in Wodonga. He joined the Victorian Railways on 17th June l947 and retired in 1988. For some time, he was a member of the Australian Federated Union of Locomotive Enginemen and served a term as a member of the Trades Hall Council. He had an extensive knowledge of the struggles that took place to achieve better conditions for railway workers. Fred worked for many years as a fireman and then worked his way up the ranks to driver, experiencing many changes from the days of steam locomotives through to diesel trains, locomotives and even the modern XPT train. He worked throughout Victoria at different stages of his career, with his final working years focused on the northeast of Victoria and the Albury to Melbourne line. After his retirement, Fred continued to share his love of steam miniature trains with the community. Cudgewa Line -The Cudgewa railway line opened in stages between 1889 and 1921. The first section from Wodonga to Huon opened on 10 September 1889. It was extended to Bolga on 18 July 1890, Tallangatta on 24 July 1891, Shelley on 13 June 1916 (the highest station in Victoria), Beetomba on 10 April 1919 and Cudgewa on 5 May 1921. In 1919, the line was used to carry materials for the construction of Hume Weir, and three years later a spur line connecting Ebden to the weir was opened. In the 1960s, Cudgewa became the railhead of materials for the Snowy Mountains Scheme. The last passenger service from Wodonga to Tallangatta ran on 30 September 1961 The turntable and passenger platform at Cudgewa were abolished in 1976.This collection has local and statewide significance as it captures images of trains, locomotives and personnel who operated the railway services in Wodonga and throughout Northeast Victoria. The railways played a critical role in opening up Victoria and connecting Australia for trade, business, social communication and transport.Historical Steam locomotive on journey to Cudgewa. Locomotive K184 leading with Driver Noel Strauss and Fireman Barrows. Locomotive K186 is the Banker with Driver Doug West. A banker is railway locomotive that temporarily assists a train that requires additional power or traction to climb a gradient. K Class Locomotives - One of VR's most successful classes of loco they were built over a 24 year period. A general purpose, light lines loco the K class had a very long career in all sorts of service from branch line passenger and goods work to pilot and banker duties and roadside mainline service. The K class is credited with working virtually every line in the VR system and hauling almost every kind of train. The majority of the class lasted into the 60's. K 184 and K186 were built by the Victorian Railways' Newport Workshops in 1945 to the successful K-class 2-8-0 locomotive design for branch-line work. K184 entered service on 9 January 1946. K186 entered service on 19 March 1946. K184 was used on heritage services with Steamrail Victoria through the 1970s. It was withdrawn from service in 1980 and is stored at Newport Workshops. and is now used as a source of spare parts; other Steamrail K Class locomotives occasionally wear its number plates and headlight number boards. K186 was scrapped on 25 October 1967.railways wodonga, fred rochow, cudgewa station, high country railway line, k class locomotives

The first tape based talking book machine from the late 1950s, produced by Clarke & Smith, that allowed the listener to hear up to 20 hours of recordings. Although bulky (each tape cartridge alone weighed over 2 kgs), the MK1 was the first magnetic, multi-track tape produced and considered quite novel for it's time. The cartridge designed to be played on the Clarke & Smith MK1 Talking Book player came in it's own separate container. Each cartridge houses the complete mechanism, track change linkages, replay heads and tape spools, which are stacked on top of each other within the housing. When one track was finished, the user was required to lift the metal cassette, turn it over, and replace it on the turntable. The bulky cartridges were distributed by post or train in strong 'Globite' cases made with reinforced corners and strapped. The costs associated with talking book players were high and individuals/groups/service clubs were asked to sponsor a machine to help those who could not afford to buy or rent one. In this example, a plate attached to the lid indicates who raised the funds: "This talking book/is presented to you/by Tallimba Branch/ of CWA of NSW." Please note: despite images, there are no cartridges with this model.Metal talking book machine housed in a brown wooden carry case. There are two plastic knobs on the front facing right hand side, and an electric cord extending from the back of the case. To the left of the knobs is a speaker grille. Also includes talking book cartridge 'The darling buds of May'.audio equipment, clarke and smith

Written on envelope attached: "This was sent to Aunty Mill from Aunty Grace. This photo was taken from our back gate opposite the post office. Miss Magan(?) was PM. The old Grenville Standard office run by Mr Adams. The little houses on the hill behind one was Mr Terrett a tailor who made the band uniforms. Mr Tom Bennett house butcher. The slaughter house is among the trees in the background. Note where the 'Law' is at the post office. I would like to see this enlarged. I think this photo is special because it shows the turntable where the trains used to turn before the rail went thru to Skipton which I remember all the [illegible] being made so many people working in Linton. As kids we loved to watch as the train came out facing a different way. The railway station master's house Mr Thompson was the SM. The old Grenville Standard office run by Mr Adams." Note: "Aunty Mill" = Amelia (Millie) Bennett, afterwards Millie Allen. "Aunty Grace" = Grace Bennett, afterwards Grace Wishart.Black and white postcard of Grenville Standard building with railway station and station master's house in background.On postcard: "Linton 30.6.09 [=1909] Dear Mill, you will be surprised at -- postcard and so soon. I forgot when writing, I wanted to ask you if Percy could get me a few dolls at wholesale price we are to have a bazaar for the church, and want to make something on our purchases. Let me know soon and I will get the money and quantity etc. required. Yours sincerely, Grace".grenville standard [newspaper], linton railway station, buildings, grace bennett afterwards grace wishart, amelia (millie) bennett afterwards millie allen